| Age | Commit message (Collapse) | Author |
|---|
|
There are cases where a PCIe extended capability should be hidden from
the user. For example, an unknown capability (i.e., capability with ID
greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally
chosen to be hidden from the user.
Hiding a capability is done by virtualizing and modifying the 'Next
Capability Offset' field of the previous capability so it points to the
capability after the one that should be hidden.
The special case where the first capability in the list should be hidden
is handled differently because there is no previous capability that can
be modified. In this case, the capability ID and version are zeroed
while leaving the next pointer intact. This hides the capability and
leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done
properly if the capability is unknown, as struct
vfio_pci_core_device->pci_config_map is set to the capability ID during
initialization but the capability ID is not properly checked later when
used in vfio_config_do_rw(). This leads to the following warning [1] and
to an out-of-bounds access to ecap_perms array.
Fix it by checking cap_id in vfio_config_do_rw(), and if it is greater
than PCI_EXT_CAP_ID_MAX, use an alternative struct perm_bits for direct
read only access instead of the ecap_perms array.
Note that this is safe since the above is the only case where cap_id can
exceed PCI_EXT_CAP_ID_MAX (except for the special capabilities, which
are already checked before).
[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1
(snip)
Call Trace:
<TASK>
? show_regs+0x69/0x80
? __warn+0x8d/0x140
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? report_bug+0x18f/0x1a0
? handle_bug+0x63/0xa0
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core]
? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core]
vfio_pci_rw+0x101/0x1b0 [vfio_pci_core]
vfio_pci_core_read+0x1d/0x30 [vfio_pci_core]
vfio_device_fops_read+0x27/0x40 [vfio]
vfs_read+0xbd/0x340
? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio]
? __rseq_handle_notify_resume+0xa4/0x4b0
__x64_sys_pread64+0x96/0xc0
x64_sys_call+0x1c3d/0x20d0
do_syscall_64+0x4d/0x120
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: 89e1f7d4c66d ("vfio: Add PCI device driver")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Tested-by: Yi Liu <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20241124142739.21698-1-avihaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
F_SET_RW_HINT controls data placement in the file system and / or
device and should not be available to everyone who can read a given file.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241122122931.90408-2-hch@lst.de
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
The group only contains a single entry and the conditionals around its
lifecycle make clear that this won't change.
Remove the unnecessary group.
This saves some memory and it's easier to read.
The removal of a non-const bin_attribute[] instance is also a
preparation for the constification of struct bin_attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20241121-sysfs-const-bin_attr-int340x_thermal-v1-1-2436facf9dae@weissschuh.net
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the current_uuid attribute is set to the active policy UUID,
reading back the same attribute is returning "INVALID" instead of
the active policy UUID on some platforms before Ice Lake.
In platforms before Ice Lake, firmware provides a list of supported
thermal policies. In this case, user space can select any of the
supported thermal policies via a write to attribute "current_uuid".
In commit c7ff29763989 ("thermal: int340x: Update OS policy capability
handshake")', the OS policy handshake was updated to support Ice Lake
and later platforms and it treated priv->current_uuid_index=0 as
invalid. However, priv->current_uuid_index=0 is for the active policy,
only priv->current_uuid_index=-1 is invalid.
Fix this issue by updating the priv->current_uuid_index check.
Fixes: c7ff29763989 ("thermal: int340x: Update OS policy capability handshake")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.18+ <stable@vger.kernel.org> # 5.18+
Link: https://patch.msgid.link/20241114200213.422303-1-srinivas.pandruvada@linux.intel.com
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Before this commit, ->dir and ->entry of exfat_inode_info record the
first cluster of the parent directory and the directory entry index
starting from this cluster.
The directory entry set will be gotten during write-back-inode/rmdir/
unlink/rename. If the clusters of the parent directory are not
continuous, the FAT chain will be traversed from the first cluster of
the parent directory to find the cluster where ->entry is located.
After this commit, ->dir records the cluster where the first directory
entry in the directory entry set is located, and ->entry records the
directory entry index in the cluster, so that there is almost no need
to access the FAT when getting the directory entry set.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
For the root directory and other directories, the clusters
allocated to them can be obtained from exfat_inode_info, and
there is no need to distinguish them.
And there is no need to initialize atime/ctime/mtime/size in
exfat_readdir(), because exfat_iterate() does not use them.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
The output of argument 'p_dir' of exfat_add_entry() is not used
in either exfat_mkdir() or exfat_create(), remove the argument.
Code refinement, no functional changes.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
__exfat_resolve_path() mixes two functions. The first one is to
resolve and check if the path is valid. The second one is to output
the cluster assigned to the directory.
The second one is only needed when need to traverse the directory
entries, and calling exfat_chain_set() so early causes p_dir to be
passed as an argument multiple times, increasing the complexity of
the code.
This commit moves the call to exfat_chain_set() before traversing
directory entries.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
This helper gets the directory entry set of the file for the exfat
inode which has been created.
It's used to remove all the instances of the pattern it replaces
making the code cleaner, it's also a preparation for changing ->dir
to record the cluster where the directory entry set is located and
changing ->entry to record the index of the directory entry within
the cluster.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
In this exfat implementation, the relationship between inode and ei
is ei=EXFAT_I(inode). However, in the arguments of exfat_move_file()
and exfat_rename_file(), argument 'inode' indicates the parent
directory, but argument 'ei' indicates the target file to be renamed.
They do not have the above relationship, which is not friendly to code
readers.
So this commit renames 'inode' to 'parent_inode', making the argument
name match its role.
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
To determine whether it is a directory, there is no need to read its
directory entry, just use S_ISDIR(inode->i_mode).
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
Unaligned direct writes are invalid and should return an error
without making any changes, rather than extending ->valid_size
and then returning an error. Therefore, alignment checking is
required before extending ->valid_size.
Fixes: 11a347fb6cef ("exfat: change to get file size from DataLength")
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Co-developed-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
There is no check if stream size and start_clu are invalid.
If start_clu is EOF cluster and stream size is 4096, It will
cause uninit value access. because ei->hint_femp.eidx could
be 128(if cluster size is 4K) and wrong hint will allocate
next cluster. and this cluster will be same with the cluster
that is allocated by exfat_extend_valid_size(). The previous
patch will check invalid start_clu, but for clarity, initialize
hint_femp.eidx to zero.
Cc: stable@vger.kernel.org
Reported-by: syzbot+01218003be74b5e1213a@syzkaller.appspotmail.com
Tested-by: syzbot+01218003be74b5e1213a@syzkaller.appspotmail.com
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
In the case of the directory size is greater than or equal to
the cluster size, if start_clu becomes an EOF cluster(an invalid
cluster) due to file system corruption, then the directory entry
where ei->hint_femp.eidx hint is outside the directory, resulting
in an out-of-bounds access, which may cause further file system
corruption.
This commit adds a check for start_clu, if it is an invalid cluster,
the file or directory will be treated as empty.
Cc: stable@vger.kernel.org
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Co-developed-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
|
|
Prepare input updates for 6.13 merge window.
|
|
Test that extacks in dumps work. The test fills up the receive buffer
to test both the inline dump (as part of sendmsg()) and delayed one
(run during recvmsg()).
Use YNL helpers to parse the messages. We need to add the test to YNL
file to make sure the right include path are used.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119224432.1713040-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit under fixes extended extack reporting to dumps.
It works under normal conditions, because extack errors are
usually reported during ->start() or the first ->dump(),
it's quite rare that the dump starts okay but fails later.
If the dump does fail later, however, the input skb will
already have the initiating message pulled, so checking
if bad attr falls within skb->data will fail.
Switch the check to using nlh, which is always valid.
syzbot found a way to hit that scenario by filling up
the receive queue. In this case we initiate a dump
but don't call ->dump() until there is read space for
an skb.
WARNING: CPU: 1 PID: 5845 at net/netlink/af_netlink.c:2210 netlink_ack_tlv_fill+0x1a8/0x560 net/netlink/af_netlink.c:2209
RIP: 0010:netlink_ack_tlv_fill+0x1a8/0x560 net/netlink/af_netlink.c:2209
Call Trace:
<TASK>
netlink_dump_done+0x513/0x970 net/netlink/af_netlink.c:2250
netlink_dump+0x91f/0xe10 net/netlink/af_netlink.c:2351
netlink_recvmsg+0x6bb/0x11d0 net/netlink/af_netlink.c:1983
sock_recvmsg_nosec net/socket.c:1051 [inline]
sock_recvmsg+0x22f/0x280 net/socket.c:1073
__sys_recvfrom+0x246/0x3d0 net/socket.c:2267
__do_sys_recvfrom net/socket.c:2285 [inline]
__se_sys_recvfrom net/socket.c:2281 [inline]
__x64_sys_recvfrom+0xde/0x100 net/socket.c:2281
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7ff37dd17a79
Reported-by: syzbot+d4373fa8042c06cefa84@syzkaller.appspotmail.com
Fixes: 8af4f60472fc ("netlink: support all extack types in dumps")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119224432.1713040-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VCAP API unit tests fail randomly with errors such as
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:387
Expected 134 + 7 == iter.offset, but
134 + 7 == 141 (0x8d)
iter.offset == 17214 (0x433e)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:388
Expected 5 == iter.reg_idx, but
iter.reg_idx == 702 (0x2be)
# vcap_api_iterator_init_test: EXPECTATION FAILED at drivers/net/ethernet/microchip/vcap/vcap_api_kunit.c:389
Expected 11 == iter.reg_bitpos, but
iter.reg_bitpos == 15 (0xf)
# vcap_api_iterator_init_test: pass:0 fail:1 skip:0 total:1
Comments in the code state that "A typegroup table ends with an all-zero
terminator". Add the missing terminators.
Some of the typegroups did have a terminator of ".offset = 0, .width = 0,
.value = 0,". Replace those terminators with "{ }" (no trailing ',') for
consistency and to excplicitly state "this is a terminator".
Fixes: 67d637516fa9 ("net: microchip: sparx5: Adding KUNIT test for the VCAP API")
Cc: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119213202.2884639-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
Fixes: eb9ad088f966 ("lan78xx: Check for supported Wake-on-LAN modes")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://patch.msgid.link/20241118140351.2398166-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Fixes: 72f2afb8a685 ("[TG3]: Add DMA address workaround")
Reported-by: Salam Noureddine <noureddine@arista.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241119055741.147144-1-pavan.chebbi@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot found that rtnl_dump_ifinfo() could return with a lock held [1]
Move code around so that rtnl_link_ops_put() and put_net()
can be called at the end of this function.
[1]
WARNING: lock held when returning to user space!
6.12.0-rc7-syzkaller-01681-g38f83a57aa8e #0 Not tainted
syz-executor399/5841 is leaving the kernel with locks still held!
1 lock held by syz-executor399/5841:
#0: ffffffff8f46c2a0 (&ops->srcu#2){.+.+}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:337 [inline]
#0: ffffffff8f46c2a0 (&ops->srcu#2){.+.+}-{0:0}, at: rcu_read_lock include/linux/rcupdate.h:849 [inline]
#0: ffffffff8f46c2a0 (&ops->srcu#2){.+.+}-{0:0}, at: rtnl_link_ops_get+0x22/0x250 net/core/rtnetlink.c:555
Fixes: 43c7ce69d28e ("rtnetlink: Protect struct rtnl_link_ops with SRCU.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241121194105.3632507-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace nested double quotes in f-string with outer single quotes.
Fixes: 6116075e18f7 ("selftests: nic_link_layer: Add link layer selftest for NIC driver")
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20241122064821.2821199-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e532 ("lan78xx: Lan7801 Support for Fixed PHY")
Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In lan78xx_probe(), the buffer `buf` was being freed twice: once
implicitly through `usb_free_urb(dev->urb_intr)` with the
`URB_FREE_BUFFER` flag and again explicitly by `kfree(buf)`. This caused
a double free issue.
To resolve this, reordered `kmalloc()` and `usb_alloc_urb()` calls to
simplify the initialization sequence and removed the redundant
`kfree(buf)`. Now, `buf` is allocated after `usb_alloc_urb()`, ensuring
it is correctly managed by `usb_fill_int_urb()` and freed by
`usb_free_urb()` as intended.
Fixes: a6df95cae40b ("lan78xx: Fix memory allocation bug")
Cc: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241116130558.1352230-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We were accidentally allocating a layout for the *square* of the object
size due to a variable shadowing mishap.
Fixes memory bloat and page allocation failures in drm/asahi.
Reported-by: Janne Grunau <j@jannau.net>
Fixes: 9e7bbfa18276 ("rust: alloc: introduce `ArrayLayout`")
Signed-off-by: Asahi Lina <lina@asahilina.net>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Link: https://lore.kernel.org/r/20241123-rust-fix-arraylayout-v1-1-197e64c95bd4@asahilina.net
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
This list started as a "when to prefer `expect`" list, but at some point
during writing I changed it to a "prefer `expect` unless..." one. However,
the first bullet remained, which does not make sense anymore.
Thus remove it. In addition, fix nearby typo.
Fixes: 04866494e936 ("Documentation: rust: discuss `#[expect(...)]` in the guidelines")
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Andreas Hindborg <a.hindborg@kernel.org>
Link: https://lore.kernel.org/r/20241117133127.473937-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
In beta Clippy (i.e. Rust 1.83.0), the `needless_lifetimes` lint has
been extended [1] to suggest eliding `impl` lifetimes, e.g.
error: the following explicit lifetimes could be elided: 'a
--> rust/kernel/list.rs:647:6
|
647 | impl<'a, T: ?Sized + ListItem<ID>, const ID: u64> FusedIterator for Iter<'a, T, ID> {}
| ^^ ^^
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#needless_lifetimes
= note: `-D clippy::needless-lifetimes` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(clippy::needless_lifetimes)]`
help: elide the lifetimes
|
647 - impl<'a, T: ?Sized + ListItem<ID>, const ID: u64> FusedIterator for Iter<'a, T, ID> {}
647 + impl<T: ?Sized + ListItem<ID>, const ID: u64> FusedIterator for Iter<'_, T, ID> {}
A possibility would have been to clean them -- the RFC patch [2] did
this, while asking if we wanted these cleanups. There is an open issue
[3] in Clippy about being able to differentiate some of the new cases,
e.g. those that do not involve introducing `'_`. Thus it seems others
feel similarly.
Thus, for the time being, we decided to `allow` the lint.
Link: https://github.com/rust-lang/rust-clippy/pull/13286 [1]
Link: https://lore.kernel.org/rust-for-linux/20241012231300.397010-1-ojeda@kernel.org/ [2]
Link: https://github.com/rust-lang/rust-clippy/issues/13514 [3]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Andreas Hindborg <a.hindborg@kernel.org>
Link: https://lore.kernel.org/r/20241116181538.369355-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Type 4 PCC channels have an option to send back a response
to the platform when they are done processing the request.
The flag to indicate whether or not to respond is inside
the message body, and thus is not available to the pcc
mailbox.
If the flag is not set, still set command completion
bit after processing message.
In order to read the flag, this patch maps the shared
buffer to virtual memory. To avoid duplication of mapping
the shared buffer is then made available to be used by
the driver that uses the mailbox.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mailbox to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Make a few indentions consistent while touching these struct
initializers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Replace %i with %u in snprintf() because it is "unsigned int".
Signed-off-by: zhang jiao <zhangjiao2@cmss.chinamobile.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Both the inner and outer loops in this code use the "i" iterator.
The inner loop should really use a different iterator.
It doesn't affect things in practice because the data comes from the
device tree. The "protocol" and "windows" variables are going to be
zero. That means we're always going to hit the "return &chans[channel];"
statement and we're not going to want to iterate through the outer
loop again.
Still it's worth fixing this for future use cases.
Fixes: 5a6338cce9f4 ("mailbox: arm_mhuv2: Add driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
As per zynqmp-ipi bindings, zynqmp IPI node can have multiple child nodes.
Current IPI setup function is set only for first child node. If IPI node
has multiple child nodes in the device-tree, then IPI setup fails for
child nodes other than first child node. In such case kernel will crash.
Fix this crash by registering IPI setup function for each available child
node.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Add bindings for the mailbox controller. This work is based on the vendor
kernel. [1]
Link: https://github.com/revyos/thead-kernel.git [1]
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
This driver was tested using the drm/imagination GPU driver. It was able
to successfully power on the GPU, by passing a command through mailbox
from E910 core to E902 that's responsible for powering up the GPU. The
GPU driver was able to read the BVNC version from control registers,
which confirms it was successfully powered on.
[ 33.957467] powervr ffef400000.gpu: [drm] loaded firmware
powervr/rogue_36.52.104.182_v1.fw
[ 33.966008] powervr ffef400000.gpu: [drm] FW version v1.0 (build
6621747 OS)
[ 38.978542] powervr ffef400000.gpu: [drm] *ERROR* Firmware failed to
boot
Though the driver still fails to boot the firmware, the mailbox driver
works when used with the not-yet-upstreamed firmware AON driver. There
is ongoing work to get the BXM-4-64 supported with the drm/imagination
driver [1], though it's not completed yet.
This work is based on the driver from the vendor kernel [2].
Link: https://gitlab.freedesktop.org/imagination/linux-firmware/-/issues/2 [1]
Link: https://github.com/revyos/thead-kernel.git [2]
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
It should be size of the struct clk_bulk_data, not data pointer pass to
devm_kcalloc().
Fixes: aa1609f571ca ("mailbox: mtk-cmdq: Dynamically allocate clk_bulk_data structure")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Document compatible for Qualcomm SM8750 SoC IPCC, compatible with
existing generic fallback.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
fallbacks
Commit 1e9cb7e007dc ("dt-bindings: mailbox: qcom,apcs-kpss-global: use
fallbacks") and commit 34d8775a0edc ("dt-bindings: mailbox:
qcom,apcs-kpss-global: use fallbacks for few variants") added fallbacks
to few existing compatibles. Neither devices with these existing
compatibles nor devices using fallbacks alone, have clocks, so the
"if:then:" block defining this constrain should be written as
"contains:".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Document compatible for the IPCC mailbox controller on SAR2130P platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The TI message manager driver can be compiled without ARCH_KEYSTONE
nor ARCH_K3 enabled. Allow it to be built under COMPILE_TEST.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
When OF support is disabled the of_device_id struct match table can be
conditionally compiled out, this helper allows the assignment to also be
turned into a NULL conditionally. When the of_device_id struct is not
conditionally defined based on OF then the table will be unused causing a
warning. The two options are to either set the table as _maybe_unused, or
to just remove this helper since the table will always be defined.
Do the latter here.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The qcom-cpucp mailbox irq is expected to function during suspend-resume
cycle particularly when the scmi cpufreq driver can query the current
frequency using the get_level message after the cpus are brought up during
resume. Hence mark the irq with IRQF_NO_SUSPEND flag to fix the do_xfer
failures we see during resume.
Err Logs:
arm-scmi firmware:scmi: timed out in resp(caller:do_xfer+0x164/0x568)
cpufreq: cpufreq_online: ->get() failed
Reported-by: Johan Hovold <johan+linaro@kernel.org>
Closes: https://lore.kernel.org/lkml/ZtgFj1y5ggipgEOS@hovoldconsulting.com/
Fixes: 0e2a9a03106c ("mailbox: Add support for QTI CPUCP mailbox controller")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
pm_runtime_put_autosuspend() will soon be changed to include a call to
pm_runtime_mark_last_busy(). This patch switches the current users to
__pm_runtime_put_autosuspend() which will continue to have the
functionality of old pm_runtime_put_autosuspend().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
The two previous bindings for this hardware were incorrect, as the
control/status and interrupt register regions should have been described
as syscons and dealt with via regmap in the driver. Add support for
accessing these registers using that method now, so that the hwmon
driver can be supported without using auxdev or hacks with io_remap().
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
When the binding for this was originally written, and later modified,
mistakes were made - and the precise nature of the later modification
should have been a giveaway, but alas I was naive at the time.
A more correct modelling of the hardware is to use two syscons and have
a single reg entry for the mailbox, containing the mailbox region. The
two syscons contain the general control/status registers for the mailbox
and the interrupt related registers respectively. The reason for two
syscons is that the same mailbox is present on the non-SoC version of
the FPGA, which has no interrupt controller, and the shared part of the
rtl was unchanged between devices.
This is now coming to a head, because the control/status registers share
a register region with the "tvs" (temperature & voltage sensors)
registers and, as it turns out, people do want to monitor temperatures
and voltages...
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
Commit 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo
flow sensor") added support for reading Octo flow sensor, but didn't
update the priv->speed_input array length. Since Octo has 8 fans, with
the addition of the flow sensor the proper length for speed_input is 9.
Reported by Arne Schwabe on Github [1], who received a UBSAN warning.
Fixes: 120584c728a6 ("hwmon: (aquacomputer_d5next) Add support for Octo flow sensor")
Closes: https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/100 [1]
Reported-by: Arne Schwabe <arne@rfc2549.org>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Message-ID: <20241124152725.7205-1-savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Remove Brendan Higgins <brendanhiggins@google.com> from i2c-aspeed entry
and replace with Ryan Chen <ryan_chen@aspeedtech.com>.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
In commit 35eba185fd1a ("i2c: designware: Calculate SCL timing parameter
for High Speed Mode") the SCL high period count and low period count for
high speed mode are calculated based on fixed tHIGH = 160 and tLOW = 120.
However, the set of two fixed values is only applicable to the combination
of hardware parameters IC_CAP_LOADING is 400 and IC_CLK_FREQ_OPTIMIZATION
is true. Outside of this combination, the SCL frequency may not reach
3.4 MHz because the fixed tHIGH and tLOW are not small enough.
If IC_CAP_LOADING is 400, it means the bus capacitance is 400pF;
Otherwise, 100 pF. If IC_CLK_FREQ_OPTIMIZATION is true, it means that the
hardware reduces its internal clock frequency by reducing the internal
latency required to generate the high period and low period of the SCL line.
Section 3.15.4.5 in DesignWare DW_apb_i2b Databook v2.03 says that when
IC_CLK_FREQ_OPTIMIZATION = 0,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 120 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 160 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
and section 3.15.4.6 says that when IC_CLK_FREQ_OPTIMIZATION = 1,
MIN_SCL_HIGHtime = 60 ns for 3.4 Mbps, bus loading = 100pF
= 160 ns for 3.4 Mbps, bus loading = 400pF
MIN_SCL_LOWtime = 120 ns for 3.4 Mbps, bus loading = 100pF
= 320 ns for 3.4 Mbps, bus loading = 400pF
In order to calculate more accurate SCL high period count and low period
count for high speed mode, two hardware parameters IC_CAP_LOADING and
IC_CLK_FREQ_OPTIMIZATION must be considered together. Since there're no
registers controlliing these these two hardware parameters, users can
declare them in the device tree so that the driver can obtain them.
Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
optimized
Since there are no registers controlling the hardware parameters
IC_CAP_LOADING and IC_CLK_FREQ_OPTIMIZATION, their values can only be
declared in the device tree.
snps,bus-capacitance-pf indicates the bus capacitance in picofarads (pF).
It affects the high and low pulse width of SCL line in high speed mode.
The legal values for this property are 100 and 400 only, and default
value is 100. This property corresponds to IC_CAP_LOADING.
snps,clk-freq-optimized indicates whether the hardware reduce its
internal clock frequency by reducing the internal latency required to
generate the high period and low period of SCL line. This property
corresponds to IC_CLK_FREQ_OPTIMIZATION.
The driver can calculate the high period count and low period count of
SCL line for high speed mode based on these two properties.
Signed-off-by: Michael Wu <michael.wu@kneron.us>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
- BRCR value must go into the BRCR1 field when in high-speed mode.
It goes into BRCR2 otherwise.
- Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.
- Set SM properly in probe; previously it only checked STANDARD versus
FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.
- Remove all comment sections saying we only support low-speeds.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Current BRCR computation is:
brcr = floor(i2cclk / (clkfreq * div))
With brcr: "baud rate counter", an internal clock divider,
and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
and clkfreq: desired bus rate,
and div: speed-mode dependent divider (2 for standard, 3 otherwise).
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) = 4
and resulting bus rate = 48MHz / (4 * 3) = 4MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz
The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:
brcr = floor(i2cclk / (clkfreq * div)) + 1
If we redo the above examples:
Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz
Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz
In kernel C code, floor(x) is DIV_ROUND_DOWN() and,
floor(x)+1 is DIV_ROUND_UP().
This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.
This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
