summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-08-25tcp: refine pacing rate determinationEric Dumazet
When TCP pacing was added back in linux-3.12, we chose to apply a fixed ratio of 200 % against current rate, to allow probing for optimal throughput even during slow start phase, where cwnd can be doubled every other gRTT. At Google, we found it was better applying a different ratio while in Congestion Avoidance phase. This ratio was set to 120 %. We've used the normal tcp_in_slow_start() helper for a while, then tuned the condition to select the conservative ratio as soon as cwnd >= ssthresh/2 : - After cwnd reduction, it is safer to ramp up more slowly, as we approach optimal cwnd. - Initial ramp up (ssthresh == INFINITY) still allows doubling cwnd every other RTT. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-25xfrm: Use VRF master index if output device is enslavedDavid Ahern
Directs route lookups to VRF table. Compiles out if NET_VRF is not enabled. With this patch able to successfully bring up ipsec tunnels in VRFs, even with duplicate network configuration. Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-25tcp: fix slow start after idle vs TSO/GSOEric Dumazet
slow start after idle might reduce cwnd, but we perform this after first packet was cooked and sent. With TSO/GSO, it means that we might send a full TSO packet even if cwnd should have been reduced to IW10. Moving the SSAI check in skb_entail() makes sense, because we slightly reduce number of times this check is done, especially for large send() and TCP Small queue callbacks from softirq context. As Neal pointed out, we also need to perform the check if/when receive window opens. Tested: Following packetdrill test demonstrates the problem // Test of slow start after idle `sysctl -q net.ipv4.tcp_slow_start_after_idle=1` 0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 +0 bind(3, ..., ...) = 0 +0 listen(3, 1) = 0 +0 < S 0:0(0) win 65535 <mss 1000,sackOK,nop,nop,nop,wscale 7> +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6> +.100 < . 1:1(0) ack 1 win 511 +0 accept(3, ..., ...) = 4 +0 setsockopt(4, SOL_SOCKET, SO_SNDBUF, [200000], 4) = 0 +0 write(4, ..., 26000) = 26000 +0 > . 1:5001(5000) ack 1 +0 > . 5001:10001(5000) ack 1 +0 %{ assert tcpi_snd_cwnd == 10 }% +.100 < . 1:1(0) ack 10001 win 511 +0 %{ assert tcpi_snd_cwnd == 20, tcpi_snd_cwnd }% +0 > . 10001:20001(10000) ack 1 +0 > P. 20001:26001(6000) ack 1 +.100 < . 1:1(0) ack 26001 win 511 +0 %{ assert tcpi_snd_cwnd == 36, tcpi_snd_cwnd }% +4 write(4, ..., 20000) = 20000 // If slow start after idle works properly, we should send 5 MSS here (cwnd/2) +0 > . 26001:31001(5000) ack 1 +0 %{ assert tcpi_snd_cwnd == 10, tcpi_snd_cwnd }% +0 > . 31001:36001(5000) ack 1 Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-25batman-adv: beautify supported routing algorithm listMarek Lindner
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Fix conditional statements indentationSven Eckelmann
commit 29b9256e6631 ("batman-adv: consider outgoing interface in OGM sending") incorrectly indented the interface check code. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Add lockdep_asserts for documented external locksSven Eckelmann
Some functions already have documentation about locks they require inside their kerneldoc header. These can be directly tested during runtime using the lockdep asserts. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Annotate deleting functions with external lock via lockdepSven Eckelmann
Functions which use (h)list_del* are requiring correct locking when they operate on global lists. Most of the time the search in the list and the delete are done in the same function. All other cases should have it visible that they require a special lock to avoid race conditions. Lockdep asserts can be used to check these problem during runtime when the lockdep functionality is enabled. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: convert bat_priv->tt.req_list to hlistMarek Lindner
Since the list's tail is never accessed using a double linked list head wastes memory. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Fix gw_bandwidth calculation on 32 bit systemsSven Eckelmann
The TVLV for the gw_bandwidth stores everything as u32. But the gw_bandwidth reads the signed long which limits the maximum value to (2 ** 31 - 1) on systems with 4 byte long. Also the input value is always converted from either Mibit/s or Kibit/s to 100Kibit/s. This reduces the values even further when the user sets it via the default unit Kibit/s. It may even cause an integer overflow and end up with a value the user never intended. Instead read the values as u64, check for possible overflows, do the unit adjustments and then reduce the size to u32. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Return EINVAL on invalid gw_bandwidth changeSven Eckelmann
Invalid speed settings by the user are currently acknowledged as correct but not stored. Instead the return of the store operation of the file "gw_bandwidth" should indicate that the given value is not acceptable. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: prevent potential hlist double deletionMarek Lindner
The hlist_del_rcu() call in batadv_tt_global_size_mod() does not check if the element still is part of the list prior to deletion. The atomic list counter should prevent the worst but converting to hlist_del_init_rcu() ensures the element can't be deleted more than once. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: convert orig_node->vlan_list to hlistMarek Lindner
Since the list's tail is never accessed using a double linked list head wastes memory. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Remove batadv_ types forward declarationsSven Eckelmann
main.h is included in every file and is the only way to access types.h. This makes forward declarations for all types defined in types.h unnecessary. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: rename batadv_new_tt_req_node to batadv_tt_req_node_newMarek Lindner
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: update kernel doc of batadv_tt_global_del_orig_entry()Marek Lindner
The updated kernel doc & additional comment shall prevent accidental copy & paste errors or calling the function without the required precautions. Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Remove multiple assignment per lineSven Eckelmann
The Linux CodingStyle disallows multiple assignments in a single line. (see chapter 1) Reported-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Fix kerneldoc over 80 column linesSven Eckelmann
Kerneldoc required single line documentation in the past (before 2009). Therefore, the 80 columns limit per line check of checkpatch was disabled for kerneldoc. But kerneldoc is not excluded anymore from it and checkpatch now enabled the check again. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-25batman-adv: Replace C99 int types with kernel typeSven Eckelmann
(s|u)(8|16|32|64) are the preferred types in the kernel. The use of the standard C99 types u?int(8|16|32|64)_t are objected by some people and even checkpatch now warns about using them. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2015-08-24Merge branch 'fjes'David S. Miller
Taku Izumi says: ==================== FUJITSU Extended Socket network device driver This patchsets adds FUJITSU Extended Socket network device driver. Extended Socket network device is a shared memory based high-speed network interface between Extended Partitions of PRIMEQUEST 2000 E2 series. You can get some information about Extended Partition and Extended Socket by referring the following manual. http://globalsp.ts.fujitsu.com/dmsp/Publications/public/CA92344-0537.pdf 3.2.1 Extended Partitioning 3.2.2 Extended Socke v2.2 -> v3: - Fix up according to David's comment (No functional change) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: ethtool supportTaku Izumi
This patch adds implementation for ethtool support. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: handle receive cancellation request interruptTaku Izumi
This patch adds implementation of handling IRQ of other receiver's receive cancellation request. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: epstop_taskTaku Izumi
This patch adds epstop_task. This task is used to process other receiver's cancellation request. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: update_zone_taskTaku Izumi
This patch adds update_zone_task. Zoning information can be changed by user. This task is used to monitor if zoning information is changed or not. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: unshare_watch_taskTaku Izumi
This patch adds unshare_watch_task. Shared buffer's status can be changed into unshared. This task is used to monitor shared buffer's status. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: force_close_taskTaku Izumi
This patch adds force_close_task. This task is used to close network device forcibly. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: interrupt_watch_taskTaku Izumi
This patch adds interrupt_watch_task. This task is used to prevent delay of interrupts. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_vlan_rx_add/kill_vidTaku Izumi
This patch adds net_device_ops.ndo_vlan_rx_add_vid and net_device_ops.ndo_vlan_rx_kill_vid callback. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_tx_timeoutTaku Izumi
This patch adds net_device_ops.ndo_tx_timeout callback. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_change_mtuTaku Izumi
This patch adds net_device_ops.ndo_change_mtu. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_get_stats64Taku Izumi
This patch adds net_device_ops.ndo_get_stats64 callback. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: NAPI polling functionTaku Izumi
This patch adds NAPI polling function and receive related work. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: tx_stall_taskTaku Izumi
This patch adds tx_stall_task. When receiver's buffer is full, sender stops its tx queue. This task is used to monitor receiver's status and when receiver's buffer is avairable, it resumes tx queue. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: raise_intr_rxdata_taskTaku Izumi
This patch add raise_intr_rxdata_task. Extended Socket Network Device is shared memory based, so someone's transmission denotes other's reception. In order to notify receivers, sender has to raise interruption of receivers. raise_intr_rxdata_task does this work. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_start_xmitTaku Izumi
This patch adds net_device_ops.ndo_start_xmit callback, which is called when sending packets. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: net_device_ops.ndo_open and .ndo_stopTaku Izumi
This patch adds net_device_ops.ndo_open and .ndo_stop callback. These function is called when network device activation and deactivation. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: buffer address regist/unregistration routineTaku Izumi
This patch adds buffer address regist/unregistration routine. This function is mainly invoked when network device's activation (open) and deactivation (close) in order to retist/unregist shared buffer address. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: ES information acquisition routineTaku Izumi
This patch adds ES information acquisition routine. ES information can be retrieved issuing information request command. ES information includes which receiver is same zone. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: platform_driver's .probe and .remove routineTaku Izumi
This patch implements platform_driver's .probe and .remove routine, and also adds board specific private data structure. This driver registers net_device at platform_driver's .probe routine and unregisters net_device at its .remove routine. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: Hardware cleanup routineTaku Izumi
This patch adds hardware cleanup routine to be invoked at driver's .remove routine. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: Hardware initialization routineTaku Izumi
This patch adds hardware initialization routine to be invoked at driver's .probe routine. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24fjes: Introduce FUJITSU Extended Socket Network Device driverTaku Izumi
This patch adds the basic code of FUJITSU Extended Socket Network Device driver. When "PNP0C02" is found in ACPI DSDT, it evaluates "_STR" to check if "PNP0C02" is for Extended Socket device driver and retrieves ACPI resource information. Then creates platform_device. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-243c59x: Add BQL support for 3c59x ethernet driver.Loganaden Velvindron
This BQL patch is based on work done by Tino Reichardt. Tested on 0000:05:00.0: 3Com PCI 3c905C Tornado at ffffc90000e6e000 by running Flent several times. Signed-off-by: Loganaden Velvindron <logan@elandsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24Merge branch 'ila-precompute'David S. Miller
Tom Herbert says: ==================== ila: Precompute checksums This patch set: - Adds argument ot LWT build_state that holds a pointer to the fib configuration being applied to the new route - Adds support in ILA to precompute checksum difference for performance optimization v2: - Move return argument in build_state to end of arguments v3: - Update the signature for ip6_tun_build_state() ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24ila: Precompute checksum difference for translationsTom Herbert
In the ILA build state for LWT compute the checksum difference to apply to transport checksums that include the IPv6 pseudo header. The difference is between the route destination (from fib6_config) and the locator to write. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-24lwt: Add cfg argument to build_stateTom Herbert
Add cfg and family arguments to lwt build state functions. cfg is a void pointer and will either be a pointer to a fib_config or fib6_config structure. The family parameter indicates which one (either AF_INET or AF_INET6). LWT encpasulation implementation may use the fib configuration to build the LWT state. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-23net: phy: add interrupt support for aquantia phyShaohui Xie
By implementing config_intr & ack_interrupt, now the phy can support link connect/disconnect interrupt. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-23Merge tag 'nfc-next-4.3-1' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next Samuel Ortiz says: ==================== NFC 4.3 pull request This is the NFC pull request for 4.3. With this one we have: - A new driver for Samsung's S3FWRN5 NFC chipset. In order to properly support this driver, a few NCI core routines needed to be exported. Future drivers like Intel's Fields Peak will benefit from this. - SPI support as a physical transport for STM st21nfcb. - An additional netlink API for sending replies back to userspace from vendor commands. - 2 small fixes for TI's trf7970a - A few st-nci fixes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-23route: fix breakage after moving lwtunnel stateJiri Benc
__recnt and related fields need to be in its own cacheline for performance reasons. Commit 61adedf3e3f1 ("route: move lwtunnel state to dst_entry") broke that on 32bit archs, causing BUILD_BUG_ON in dst_hold to be triggered. This patch fixes the breakage by moving the lwtunnel state to the end of dst_entry on 32bit archs. Unfortunately, this makes it share the cacheline with __refcnt and may affect performance, thus further patches may be needed. Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 61adedf3e3f1 ("route: move lwtunnel state to dst_entry") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-23Merge tag 'linux-can-next-for-4.3-20150820' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== this is a pull request of a two patches for net-next. The first patch is by Nik Nyby and fixes a typo in a function name. The second patch by Lucas Stach demotes register output to debug level. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-23Merge branch 'tipc-failover-fixes'David S. Miller
Jon Maloy says: ==================== tipc: fix link failover/synch problems We fix three problems with the new link failover/synch implementation, which was introduced earlier in this release cycle. They are all related to situations where there is a very short interval between the disabling and enabling of interfaces. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-30 08:08:44 +0000