| Age | Commit message (Collapse) | Author |
|---|
|
I was dumping the DDI translation tables to make sure my patch updating
the HDMI entry was doing the right thing when I noticed that the table
was showing reset values after DPMS.
And indeed, the DDI translation registers are in power well 1 on SKL,
and so we're losing their values when shutting down eDP.
Calling intel_prepare_ddi() on PW1 enabling re-programs the table.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We don't use this function on gen9, no need for that test here.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The pipe interrupt registers are in the actual pipe power well, so we
need to restore them when re-enable the corresponding power well.
I've also copied what we do on HSW/BDW for VGA, even if the we haven't
enabled unclaimed registers just yet.
v2: Don't run skl_power_well_post_enable() if the power well is already
enabled (Paulo)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Just to be more consistent with what we do on HSW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Just like what we do for HSW/BDW, having those variables makes it a bit
easier to parse the code.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
While we only need to restore pipe B/C interrupt registers on BDW when
enabling the power well, skylake a bit more flexible and we'll also need
to restore the pipe A registers as it has its own power well that can be
toggled.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Collect the currently enabled counts of slice, subslice, and
execution units using the power gate control ack message
registers specific to Cherryview.
Slice/subslice/EU info and hardware status can now be
determined for CHV, so allow the debugfs SSEU status dump
to proceed for CHV devices.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Total EU was already being detected on CHV, so we just add the
additional info parameters. The detection method is changed to
be more robust in the case of subslice fusing - we don't want
to trust the EU fuse bits corresponding to subslices which are
fused-off.
v2: Fixed subslice disable bitmasks and removed unnecessary ?
operation (Ville)
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Poke at the CBR1_VLV register during init_clock_gating to make sure the
PND deadline scheme is used.
The hardware has two modes of operation wrt. watermarks:
1) PND deadline mode:
- memory request deadline is calculated from actual FIFO level * DDL
- WM1 watermark values are unused (AFAIK)
- WM watermark level defines when to start fetching data from memory
(assuming trickle feed is not used)
2) backup mode
- deadline is based on FIFO status, DDL is unused
- FIFO split into three regions with WM and WM1 watermarks, each
part specifying a different FIFO status
We want to use the PND deadline mode, so let's make sure the chicken
bit is in the correct position on init.
Also take the opportunity to refactor the shared code between VLV and
CHV to a shared function.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
VLV/CHV have similar DSPARB registers as older platforms, just more of
them due to more planes. Add a bit of code to read out the current FIFO
split from the registers. Will be useful later when we improve the WM
calculations.
v2: Add display_mmio_offset to DSPARB
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that we have drm_planes for the cursor and primary we can move the
pixel_size handling into vlv_compute_drain_latency() and just pass the
appropriate plane to it.
v2: Check plane->state->fb instead of plane->fb
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with Matt's s/plane->fb/plane->state->fb/
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Introduce struct vlv_wm_values to house VLV watermark/drain latency
values. We start by using it when computing the drain latency values.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Move the DDL precision handling into vlv_compute_drain_latency() so the
callers don't have to duplicate the same code to deal with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The current drain lantency computation relies on hardcoded limits to
determine when the to use the low vs. high precision multiplier.
Rewrite the code to use a more straightforward approach.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Kill the silly DRAIN_LATENCY_PRECISION_* defines and just use the raw
number instead.
v2: Move the sprite 32/16 -> 16/8 preision multiplier
change to another patch (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Apparently we must yet halve the DDL drain latency from what we're
using currently. This little nugget is not in any spec, but came
down through the grapevine.
This makes the displays a bit more stable. Not quite fully stable but at
least they don't fall over immediately on driver load.
v2: Update high_precision in valleyview_update_sprite_wm() too (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If we have a single unclaimed register, we will have lots. A WARN for
each one makes the machine unusable and does not aid debugging. Convert
the i915.mmio_debug option to a counter for how many WARNs to fire
before shutting up. Even when i915.mmio_debug was disabled it would
continue to shout an *ERROR* for every interrupt, without any
information at all for debugging.
The massive verbiage was added in
commit 5978118c39c2f72fd8b39ef9c086723542384809
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 16 17:49:29 2014 -0300
drm/i915: reorganize the unclaimed register detection code
v2: Automatically enable invalid mmio reporting for the *next* invalid
access if mmio_debug is disabled by default. This should give us clearer
debug information without polluting the logs too much.
v3: Compile fixes, rebase.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Update modparam text per the thread.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
drivers/gpu/drm/i915/intel_ringbuffer.c:435:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
commit 05a2fb157e44 ("drm/i915: Consolidate forcewake code")
failed to take into account that we have used to reset both
the gen6 style and the multithreaded style forcewake registers.
This is due to fact that ivb can use either, depending on how the
bios has set up the machine.
Mimic the old semantics before we have determined the correct variety
and reset both before the ecobus probe.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Apparently, this has never worked reliably and is currently disabled. Also, the
gains are not particularly impressive. Thus rather than try to keep unused code
from decaying and having to update it for other driver changes, it was decided
to simply remove it.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We need to disable all sprite planes when disabling the CRTC. We had
been using the top-level atomic 'disable' entrypoint to accomplish this,
which was wrong. Not only can this lead to various locking issues, it
also modifies the actual plane state, making it impossible to restore
the plane properly later. For example, a DPMS off followed by a DPMS on
will result in any sprite planes in use not being restored properly.
The proper solution here is to call directly into our 'commit plane'
hook with a copy of the plane's current state that has 'visible' set to
false. Committing this dummy state will turn off the plane, but will
not touch the actual plane->state pointer, allowing us to properly
restore the plane state later.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the requested size is less than what the full range
of pdps can address, we end up setting pdps for only the
requested area.
The logical context however needs all pdp entries to be valid.
Prior to commit 06fda602dbca ("drm/i915: Create page table allocators")
we have been writing pdp entries with dma address of zero instead
of valid pdps. This is supposedly bad even if those pdps are not
addressed.
As commit 06fda602dbca ("drm/i915: Create page table allocators")
introduced more dynamic structure for pdps, we ended up oopsing
when we populated the lrc context. Analyzing this oops revealed
the fact that we have not been writing valid pdps with bsw, as
it is doing the ppgtt init with 2GB limit in some cases.
We should do the right thing and setup the non addressable part
pdps/pde/pte to scratch page through the minimal structure by
having just pdp with pde entries pointing to same page with
pte entries pointing to scratch page.
But instead of going through that trouble, setup all the pdps
through individual pd pages and pt entries, even for non
addressable parts. And let the clear range point them to scratch
page. This way we populate the lrc with valid pdps and wait
for dynamic page allocation work to land, and do the heavy lifting
for truncating page table tree according to usage.
The regression of oopsing in init was introduced by
commit 06fda602dbca ("drm/i915: Create page table allocators")
v2: Clear the range for the unused part also (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89350
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Valtteri Rantala <valtteri.rantala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Making the link_clock half in switch inline with the DPLL_CTRL1_* macros
(Ville)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
eDp 1.4 supports custom frequencies.
Skylake supports following intermediate frequencies : 3.24 GHz, 2.16 GHz and
4.32 GHz along with usual LBR, HBR and HBR2 frequencies.
Read sink supported frequencies and get common frequencies from sink and
source and use these for link training.
v2: Rebased, removed calculation of min_clock since for edp it is taken as
max_clock (as per comment).
v3: Keeping single array for link rates (Satheesh)
v4: Setting LINK_BW_SET to 0 when setting LINK_RATE_SET (Satheesh)
v5: Some minor nits (Ville)
v6: Keeping separate arrays for source and sink rates (Ville)
v7: Remove redundant setting of DP_LINK_BW_SET to 0 (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Using DP_SUPPORTED_LINK_RATES macro for supported_rates array (Satheesh).
v3: Reading dpcd's supported link rates tables based upon edp version in the
same patch.
v4: Move version check under is_edp (Satheesh)
v5: Using le16 for rates, some naming, and removing nested if block (Ville)
v6: Correctly using DP_MAX_SUPPORTED_RATES and removing DP_SUPPORTED_LINK_RATES
(Ville)
v7: Incorrectly removed DP_SUPPORTED_LINK_RATES in v6, re-adding it
v8: Checking return value of intel_dp_dpcd_read_wake() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Kill the blt/render tracking we currently have and use the frontbuffer
tracking infrastructure.
Don't enable things by default yet.
v2: (Rodrigo) Fix small conflict on rebase and typo at subject.
v3: (Paulo) Rebase on RENDER_CS change.
v4: (Paulo) Rebase.
v5: (Paulo) Simplify: flushes don't have origin (Daniel).
Also rebase due to patch order changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In invalidate and flush functions of eDP DRRS, if deferred downclock
work starts execution at a time window between acquiring the drrs
mutex and cancellation of the deferred work
(intel_edp_drrs_downclock_work), then deferred work will find
drrs mutex locked and wait for the same.
Meanwhile the function that acquired mutex drrs invalidate/flush will
wait for the completion of the deferred work before releasing the mutex.
Thats a deadlock.
To avoid such deadlock scenario, this change cancels the deferred work
before acquiring the mutex at invalidate and flush functions.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Adding a debugfs entry to determine if DRRS is supported or not
V2: [By Ram]: Following details about the active crtc will be filled
in seq-file of the debugfs
1. Encoder output type
2. DRRS Support on this CRTC
3. DRRS current state
4. Current Vrefresh
Format is as follows:
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_HIGH_RR, Vrefresh: 60
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_LOW_RR, Vrefresh: 40
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
V3: [By Ram]: Readability is improved.
Another error case is covered [Daniel]
V4: [By Ram]: Current status of the Idleness DRRS along with
the Front buffer bits are added to the debugfs. [Rodrigo]
V5: [By Ram]: Rephrased to make it easy to understand.
And format is modified. [Rodrigo]
V6: [By Ram]: Modeset mutex are acquired for each crtc along with
renaming the Idleness detection states [Daniel]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: dump full busy_frontbuffer_bits and remove the dubios
computed logical state of DRRS - debugfs is about what is fact,
developers should reach their own conclusion when debugging issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Adds a parameter which can be used with DRM_I915_GETPARAM to query the
GPU revision. The intention is to use this in Mesa to implement the
WaDisableSIMD16On3SrcInstr workaround on Skylake but only for
revision 2.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When logging that full mode switch is necessary, log which connector,
encoder or crtc has caused it, so it is easier to figure out what is
goind on by just looking at the log.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We have similar macros for crtcs and encoders, and the pattern happens
often enough to justify the macro.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
In the path were there is no state to duplicate, the allocated crtc
state wouldn't have the crtc backpointer initialized.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The current minimum vco frequency leaves us with a gap in our supported
frequencies at 233-243 MHz. Your typical 2560x1440@60 display wants a
pixel clock of 241.5 MHz, which is just withing that gap. Reduce the
allowed vco min frequency to 4.8GHz to reduce the gap to 233-240 MHz,
and thus allow such displays to work.
4.8 GHz is actually the documented (at least in some docs) limit of the
PLL, and we just picked 4.86 GHz originally because that was the lowest
value produced by the PLL spreadsheet, which obviously didn't consider
2560x1440 displays.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We need this for FBC, and possibly for PSR too.
v2: Don't only flush: invalidate too (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We want to port FBC to the frontbuffer tracking infrastructure, but
for that we need to know what caused the object invalidation so
we can react accordingly: CPU mmaps need manual, GTT mmaps and
flips don't need handling and ring rendering needs nukes.
v2: - s/ORIGIN_RENDER/ORIGIN_CS/ (Daniel, Rodrigo)
- Fix copy/pasted wrong documentation
- Rebase
v3: - Rebase
v4: - Don't pass the operation to flushes (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
helpers"
This reverts commit 3f678c96abb43a977d2ea41aefccdc49e8a3e896.
We've been a bit too optimistic with this one here :(
The trouble is that internally we're still using these plane
update/disable hooks. Which was totally ok pre-atomic since the drm
core did all the book-keeping updating and these just mostly updated
hw state. But with atomic there's lots more going on, and it causes
heaps of trouble with the load detect code.
This one specifically cause a deadlock since both the load detect code
and the nested plane atomic helper functions tried to grab the same
locks. It only blows up because of the evil tricks though we play with
the implicit ww acquire context.
Applying this revert unearths the NULL deref on already freed
framebuffer objects reported as a regression in 4.0 by various people.
Fixing this will be fairly invasive, hence revert even for the
4.1-next queue.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This translation entry was updated after electrical validation by the hw
team. The other entries are removed from existence as they aren't
validated and because the sole use of a certain type of level shifter
for SKL products is anticipated.
v2: Remove all the other entries and force the use of the 800mv+2dB
config (Sonika)
Suggested-by: Sonika Jindal <sonika.jindal@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.
Let's make for_each_sprite() take dev_priv as its first argument then.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.
Let's make for_each_plane() take dev_priv as its first argument then.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With the two-step reset counter increments which braket the actual
reset code and the subsequent wake-up we're guaranteeing that all the
lockless waiters _will_ be woken up. And since we unconditionally bail
out of waits with -EAGAIN (or -EIO) in that case there is not risk of
lost interrupt enabling bits when the lockless wait code races against
a gpu reset.
Let's remove this FIXME as resolved then.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
plane->fb is a legacy pointer that not always be up-to-date (or updated
early enough). Make sure the watermark code uses plane->state->fb so
that we're always doing our calculations based on the correct
framebuffers.
This patch was generated by Coccinelle with the following semantic
patch:
@@
struct drm_plane *P;
@@
- P->fb
+ P->state->fb
v2: Rebase
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The cursor size fields in intel_crtc just duplicate the data from
cursor->state.crtc_{w,h} so we don't need them any more. Worse, their
use in the watermark code actually introduces a subtle bug since they
don't get updated to mirror the state values until the plane commit
stage, which is *after* we've already used them to calculate new
watermark values. This happens because we had to move watermark updates
slightly earlier (outside vblank evasion) in commit
commit 32b7eeec4d1e861230b09d437e95d76c86ff4a68
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Wed Dec 24 07:59:06 2014 -0800
drm/i915: Refactor work that can sleep out of commit (v7)
Dropping the intel_crtc fields and just using the state values (which
are properly updated by the time watermark updates happen) should solve
the problem.
Aside from the actual removal of the struct fields (which are formatted
in a way that I couldn't figure out how to match in Coccinelle), the
rest of this patch was generated via the following semantic patch:
// Drop assignment
@@
struct intel_crtc *C;
struct drm_plane_state S;
@@
(
- C->cursor_width = S.crtc_w;
|
- C->cursor_height = S.crtc_h;
)
// Replace usage
@@
struct intel_crtc *C;
expression E;
@@
(
- C->cursor_width
+ C->base.cursor->state->crtc_w
|
- C->cursor_height
+ C->base.cursor->state->crtc_h
|
- to_intel_crtc(E)->cursor_width
+ E->cursor->state->crtc_w
|
- to_intel_crtc(E)->cursor_height
+ E->cursor->state->crtc_h
)
v2: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89346
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
However, there are some places in kernel code that directly set
plane->fb and neglect to update plane->state->fb. If we never do a
successful update through the atomic pipeline, the RmFB cleanup code
will look at the plane->state->fb pointer, which has never actually
been set to a legitimate value, and try to clean it up, leading to
BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb and call it everywhere the driver tries to manually set
plane->fb outside of the atomic pipeline. In this function, use
drm_atomic_set_fb_for_plane instead of writing plane->state->fb
directly to keep the reference count right.
This is modified from Matt Roper's patch to drm-intel-nightly with
commit id
commit afd65eb4cc0578a9c07d621acdb8a570e2782bf7
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Feb 3 13:10:04 2015 -0800
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
However this bug exists in mainline kernel too, so I created this to fix
it in mainline kernel.
A minor change is to use drm_atomic_set_fb_for_plane instead of update
reference count manually.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93711
Signed-off-by: Xi Ruoyao <xry111@outlook.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[Jani: included the patch notes in the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
|
|
Pull drm fix from Dave Airlie:
"An oops snuck in in an -rc3 patch, this fixes it"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
[PATCH] drm/mm: Fix support 4 GiB and larger ranges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
|
|
bad argument if(tmp)... in check_free_hole
fix oops: kernel BUG at drivers/gpu/drm/drm_mm.c:305!
[airlied: excellent, this was my task for today].
Signed-off-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather unpleasantly large set of bug fixes for arm-soc, Most
of them because of cross-tree dependencies for Exynos where we should
have figured out the right path to merge things before the merge
window, and then the maintainer being unable to sort things out in
time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile express
and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down on Exynos5
- Multiple small OMAP power management fixes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: vexpress: update CONFIG_USB_ISP1760 option
ARM: digicolor: add the machine directory to Makefile
ARM: STi: Add STiH410 SoC support
MAINTAINERS: add Freescale Vybrid SoC
MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
...
|
|
Pull irqchip fixes from Jason Cooper:
"armada-370-xp:
- Chained per-cpu interrupts
gic{,-v3,v3-its}"
- Various fixes for safer operation"
* tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux:
irqchip: gicv3-its: Support safe initialization
irqchip: gicv3-its: Define macros for GITS_CTLR fields
irqchip: gicv3-its: Add limitation to page order
irqchip: gicv3-its: Use 64KB page as default granule
irqchip: gicv3-its: Zero itt before handling to hardware
irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
irqchip: gic: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
irqchip: gicv3-its: Fix ITS CPU init
irqchip: armada-370-xp: Fix chained per-cpu interrupts
|
