| Age | Commit message (Collapse) | Author |
|---|
|
Commit 339f28964147 ("ixgbevf: Add support for new mailbox communication
between PF and VF") added support for v1.5 of the PF to VF mailbox
communication API. This commit mistakenly enabled IPSEC offload for API
v1.5.
No implementation of the v1.5 API has support for IPSEC offload. This
offload is only supported by the Linux PF as mailbox API v1.4. In fact, the
v1.5 API is not implemented in any Linux PF.
Attempting to enable IPSEC offload on a PF which supports v1.5 API will not
work. Only the Linux upstream ixgbe and ixgbevf support IPSEC offload, and
only as part of the v1.4 API.
Fix the ixgbevf Linux driver to stop attempting IPSEC offload when
the mailbox API does not support it.
The existing API design choice makes it difficult to support future API
versions, as other non-Linux hosts do not implement IPSEC offload. If we
add support for v1.5 to the Linux PF, then we lose support for IPSEC
offload.
A full solution likely requires a new mailbox API with a proper negotiation
to check that IPSEC is actually supported by the host.
Fixes: 339f28964147 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit d9028db618a6 ("idpf: convert to libeth Tx buffer completion")
inadvertently removed code that was necessary for the tx buffer cleaning
routine to iterate over all buffers associated with a packet.
When a frag is too large for a single data descriptor, it will be split
across multiple data descriptors. This means the frag will span multiple
buffers in the buffer ring in order to keep the descriptor and buffer
ring indexes aligned. The buffer entries in the ring are technically
empty and no cleaning actions need to be performed. These empty buffers
can precede other frags associated with the same packet. I.e. a single
packet on the buffer ring can look like:
buf[0]=skb0.frag0
buf[1]=skb0.frag1
buf[2]=empty
buf[3]=skb0.frag2
The cleaning routine iterates through these buffers based on a matching
completion tag. If the completion tag is not set for buf2, the loop will
end prematurely. Frag2 will be left uncleaned and next_to_clean will be
left pointing to the end of packet, which will break the cleaning logic
for subsequent cleans. This consequently leads to tx timeouts.
Assign the empty bufs the same completion tag for the packet to ensure
the cleaning routine iterates over all of the buffers associated with
the packet.
Fixes: d9028db618a6 ("idpf: convert to libeth Tx buffer completion")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Madhu chittim <madhu.chittim@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev mode the uplink VSI should receive all unmatched packets,
including VLANs. Therefore, VLAN pruning should be disabled if uplink is
in switchdev mode. It is already being done in ice_eswitch_setup_env(),
however the addition of ice_up() in commit 44ba608db509 ("ice: do
switchdev slow-path Rx using PF VSI") caused VLAN pruning to be
re-enabled after disabling it.
Add a check to ice_set_vlan_filtering_features() to ensure VLAN
filtering will not be enabled if uplink is in switchdev mode. Note that
ice_is_eswitch_mode_switchdev() is being used instead of
ice_is_switchdev_running(), as the latter would only return true after
the whole switchdev setup completes.
Fixes: 44ba608db509 ("ice: do switchdev slow-path Rx using PF VSI")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 608a5c05c39b ("virtchnl: support queue rate limit and quanta
size configuration") introduced new virtchnl ops:
- get_qos_caps
- cfg_q_bw
- cfg_q_quanta
New ops were added to ice_virtchnl_dflt_ops, in
commit 015307754a19 ("ice: Support VF queue rate limit and quanta
size configuration"), but not to the ice_virtchnl_repr_ops. Because
of that, if we get one of those messages in switchdev mode we end up
with NULL pointer dereference:
[ 1199.794701] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 1199.794804] Workqueue: ice ice_service_task [ice]
[ 1199.794878] RIP: 0010:0x0
[ 1199.795027] Call Trace:
[ 1199.795033] <TASK>
[ 1199.795039] ? __die+0x20/0x70
[ 1199.795051] ? page_fault_oops+0x140/0x520
[ 1199.795064] ? exc_page_fault+0x7e/0x270
[ 1199.795074] ? asm_exc_page_fault+0x22/0x30
[ 1199.795086] ice_vc_process_vf_msg+0x6e5/0xd30 [ice]
[ 1199.795165] __ice_clean_ctrlq+0x734/0x9d0 [ice]
[ 1199.795207] ice_service_task+0xccf/0x12b0 [ice]
[ 1199.795248] process_one_work+0x21a/0x620
[ 1199.795260] worker_thread+0x18d/0x330
[ 1199.795269] ? __pfx_worker_thread+0x10/0x10
[ 1199.795279] kthread+0xec/0x120
[ 1199.795288] ? __pfx_kthread+0x10/0x10
[ 1199.795296] ret_from_fork+0x2d/0x50
[ 1199.795305] ? __pfx_kthread+0x10/0x10
[ 1199.795312] ret_from_fork_asm+0x1a/0x30
[ 1199.795323] </TASK>
Fixes: 015307754a19 ("ice: Support VF queue rate limit and quanta size configuration")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix incorrect PHY timestamp extraction for ETH56G.
It's better to use FIELD_PREP() than manual shift.
Fixes: 7cab44f1c35f ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
To check if PHY Clock Recovery mechanic is available for a device, there
is a need to verify if given PHY is available within the netlist, but the
netlist node type used for the search is wrong, also the search context
shall be specified.
Modify the search function to allow specifying the context in the
search.
Use the PHY node type instead of CLOCK CONTROLLER type, also use proper
search context which for PHY search is PORT, as defined in E810
Datasheet [1] ('3.3.8.2.4 Node Part Number and Node Options (0x0003)' and
'Table 3-105. Program Topology Device NVM Admin Command').
[1] https://cdrdv2.intel.com/v1/dl/getContent/613875?explicitVersion=true
Fixes: 91e43ca0090b ("ice: fix linking when CONFIG_PTP_1588_CLOCK=n")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commits 7999edc484ca ("virt: arm-cca-guest: TSM_REPORT support for
realm") and a06c3fad49a5 ("drivers/virt: pkvm: Add initial support for
running as a protected guest") added arm64 guest-side support for
running in CCA and pKVM confidential computing environments
respectively.
Unfortunately, these changes were not accompanied by a MAINTAINERS
entry and so aren't automatically picked up by the get_maintainer.pl
script. Since the initial support was merged via the arm64 tree, extend
the ARM64 entry to cover the two new directories.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20241202145731.6422-3-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Calling the MMIO_GUARD hypercall from guests which have not been
enrolled (e.g. because they are running without pvmfw) results in
-EINVAL being returned. In this case, MMIO_GUARD is not active
and so we can simply proceed with the normal ioremap() routine.
Don't fail ioremap() if MMIO_GUARD fails; instead WARN_ON_ONCE()
to highlight that the pvm environment is slightly wonky.
Fixes: 0f1269495800 ("drivers/virt: pkvm: Intercept ioremap using pKVM MMIO_GUARD hypercall")
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241202145731.6422-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When arm64 is configured with CONFIG_DEBUG_VIRTUAL=y, a warning is
printed from the patching code because patch_map(), e.g.
| ------------[ cut here ]------------
| WARNING: CPU: 0 PID: 0 at arch/arm64/kernel/patching.c:45 patch_map.constprop.0+0x120/0xd00
| CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 6.13.0-rc1-00002-ge1a5d6c6be55 #1
| Hardware name: linux,dummy-virt (DT)
| pstate: 800003c5 (Nzcv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : patch_map.constprop.0+0x120/0xd00
| lr : patch_map.constprop.0+0x120/0xd00
| sp : ffffa9bb312a79a0
| x29: ffffa9bb312a79a0 x28: 0000000000000001 x27: 0000000000000001
| x26: 0000000000000000 x25: 0000000000000000 x24: 00000000000402e8
| x23: ffffa9bb2c94c1c8 x22: ffffa9bb2c94c000 x21: ffffa9bb222e883c
| x20: 0000000000000002 x19: ffffc1ffc100ba40 x18: ffffa9bb2cf0f21c
| x17: 0000000000000006 x16: 0000000000000000 x15: 0000000000000004
| x14: 1ffff5376625b4ac x13: ffff753766a67fb8 x12: ffff753766919cd1
| x11: 0000000000000003 x10: 1ffff5376625b4c3 x9 : 1ffff5376625b4af
| x8 : ffff753766254f0a x7 : 0000000041b58ab3 x6 : ffff753766254f18
| x5 : ffffa9bb312d9bc0 x4 : 0000000000000000 x3 : ffffa9bb29bd90e4
| x2 : 0000000000000002 x1 : ffffa9bb312d9bc0 x0 : 0000000000000000
| Call trace:
| patch_map.constprop.0+0x120/0xd00 (P)
| patch_map.constprop.0+0x120/0xd00 (L)
| __aarch64_insn_write+0xa8/0x120
| aarch64_insn_patch_text_nosync+0x4c/0xb8
| arch_jump_label_transform_queue+0x7c/0x100
| jump_label_update+0x154/0x460
| static_key_enable_cpuslocked+0x1d8/0x280
| static_key_enable+0x2c/0x48
| early_randomize_kstack_offset+0x104/0x168
| do_early_param+0xe4/0x148
| parse_args+0x3a4/0x838
| parse_early_options+0x50/0x68
| parse_early_param+0x58/0xe0
| setup_arch+0x78/0x1f0
| start_kernel+0xa0/0x530
| __primary_switched+0x8c/0xa0
| irq event stamp: 0
| hardirqs last enabled at (0): [<0000000000000000>] 0x0
| hardirqs last disabled at (0): [<0000000000000000>] 0x0
| softirqs last enabled at (0): [<0000000000000000>] 0x0
| softirqs last disabled at (0): [<0000000000000000>] 0x0
| ---[ end trace 0000000000000000 ]---
The warning has been produced since commit:
3e25d5a49f99b75b ("asm-generic: add an optional pfn_valid check to page_to_phys")
... which added a pfn_valid() check into page_to_phys(), and at this
point in boot pfn_valid() will always return false because the vmemmap
has not yet been initialized and there are no valid mem_sections yet.
Before that commit, the arithmetic performed by page_to_phys() would
give the expected physical address, though it is somewhat dubious to use
vmemmap addresses before the vmemmap has been initialized.
Aside from kernel image addresses, all executable code should be
allocated from execmem (where all allocations will fall within the
vmalloc area), and so there's no need for the fallback case when
CONFIG_EXECMEM=n.
Simplify patch_map() accordingly, directly converting kernel image
addresses and removing the redundant fallback case.
Fixes: 3e25d5a49f99 ("asm-generic: add an optional pfn_valid check to page_to_phys")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241202170359.1475019-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Be specific about what fields should be accessed in the idr result and
give other guidance to the VMM on how it should generate the
vIDR. Discussion on the list, and review of the qemu implementation
understood this needs to be clearer and more detailed.
Link: https://patch.msgid.link/r/0-v1-191e5e24cec3+3b0-iommufd_smmuv3_hwinf_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Commit ba0fb44aed47 ("dma-mapping: replace zone_dma_bits by
zone_dma_limit") and subsequent patches changed how zone_dma_limit is
calculated to allow a reduced ZONE_DMA even when RAM starts above 4GB.
Commit 122c234ef4e1 ("arm64: mm: keep low RAM dma zone") further fixed
this to ensure ZONE_DMA remains below U32_MAX if RAM starts below 4GB,
especially on platforms that do not have IORT or DT description of the
device DMA ranges. While zone boundaries calculation was fixed by the
latter commit, zone_dma_limit, used to determine the GFP_DMA flag in the
core code, was not updated. This results in excessive use of GFP_DMA and
unnecessary ZONE_DMA allocations on some platforms.
Update zone_dma_limit to match the actual upper bound of ZONE_DMA.
Fixes: ba0fb44aed47 ("dma-mapping: replace zone_dma_bits by zone_dma_limit")
Cc: <stable@vger.kernel.org> # 6.12.x
Reported-by: Yutang Jiang <jiangyutang@os.amperecomputing.com>
Tested-by: Yutang Jiang <jiangyutang@os.amperecomputing.com>
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20241125171650.77424-1-yang@os.amperecomputing.com
[catalin.marinas@arm.com: some tweaking of the commit log]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
This series prepares for dissimilar aggregation of CS42L43 + CS35L56
speaker playback. The CS35L56 SoundWire DAI is split into separate
DAIs for playback and capture so they can be routed and aggregated
differently.
The cs_amp driver is also updated to enable different TX (capture)
slots on each CS35L56 on a bus, so that the captures can be aggregated.
|
|
Merge series from "Csókás, Bence" <csokas.bence@prolan.hu>:
Support for Allwinner F1C100s/200s series audio was
submitted in 2018 as an RFC series, but was not merged,
despite having only minor errors. However, this is
essential for having audio on these SoCs.
This series was forward-ported/rebased to the best of
my abilities, on top of Linus' tree as of now:
commit 28eb75e178d3 ("Merge tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel")
Link: https://lore.kernel.org/all/cover.1543782328.git.mesihkilinc@gmail.com/
As requested by many, this series will now be split in 2, the DMA and the
ALSA/ASoC codec driver. This is the codec part of the series.
The first part (DMA) is at the link below. The first 3 patches of this
series can be applied and built without the former series, but for working
audio you need them both, plus the last 2 Device Tree patches in this series.
Link: https://lore.kernel.org/linux-kernel/20241122161128.2619172-1-csokas.bence@prolan.hu/
|
|
Merge series from Takashi Iwai <tiwai@suse.de>:
I stumbled upon the use of *-objs in Makefile in a few places in
ASoC. Here are trivial patches to correct those.
|
|
Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:
Define regmap for PHY and PLL registers, the PHY and PLL
registers are accessed by AI interface in controller.
Then driver can use regcache to recover registers
after suspend and resume.
|
|
compile-testing
Merely enabling compile-testing should not enable additional functionality.
Fixes: 0be58e0553812fcb ("irqchip/stm32mp-exti: Allow building as module")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/ef5ec063b23522058f92087e072419ea233acfe9.1733243115.git.geert+renesas@glider.be
|
|
Commit cdd30ebb1b9f ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts the misconversions introduced by commit cdd30ebb1b9f
("module: Convert symbol namespace to string literal").
The affected descriptions refer to MODULE_IMPORT_NS() tags in general,
rather than suggesting the use of the empty string ("") as the
namespace.
Fixes: cdd30ebb1b9f ("module: Convert symbol namespace to string literal")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit cdd30ebb1b9f ("module: Convert symbol namespace to string
literal"), when MODULE_IMPORT_NS() is missing, 'make nsdeps' inserts
pointless code:
MODULE_IMPORT_NS("ns");
Here, "ns" is not a namespace, but the variable in the semantic patch.
It must not be quoted. Instead, a string literal must be passed to
Coccinelle.
Fixes: cdd30ebb1b9f ("module: Convert symbol namespace to string literal")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was missing in the series introducing the fault object. Thus, add it.
Link: https://patch.msgid.link/r/d61b9b7f73276cc8f1aef9602bd35c486917506e.1733212723.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
As fput() calls the file->f_op->release op, where fault obj and ictx are
getting released, there is no need to release these two after fput() one
more time, which would result in imbalanced refcounts:
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 48 PID: 2369 at lib/refcount.c:31 refcount_warn_saturate+0x60/0x230
Call trace:
refcount_warn_saturate+0x60/0x230 (P)
refcount_warn_saturate+0x60/0x230 (L)
iommufd_fault_fops_release+0x9c/0xe0 [iommufd]
...
VFS: Close: file count is 0 (f_op=iommufd_fops [iommufd])
WARNING: CPU: 48 PID: 2369 at fs/open.c:1507 filp_flush+0x3c/0xf0
Call trace:
filp_flush+0x3c/0xf0 (P)
filp_flush+0x3c/0xf0 (L)
__arm64_sys_close+0x34/0x98
...
imbalanced put on file reference count
WARNING: CPU: 48 PID: 2369 at fs/file.c:74 __file_ref_put+0x100/0x138
Call trace:
__file_ref_put+0x100/0x138 (P)
__file_ref_put+0x100/0x138 (L)
__fput_sync+0x4c/0xd0
Drop those two lines to fix the warnings above.
Cc: stable@vger.kernel.org
Fixes: 07838f7fd529 ("iommufd: Add iommufd fault object")
Link: https://patch.msgid.link/r/b5651beb3a6b1adeef26fffac24607353bf67ba1.1733212723.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Fix typos/spellos in kernel-doc comments for readability.
Fixes: aad37e71d5c4 ("iommufd: IOCTLs for the io_pagetable")
Fixes: b7a0855eb95f ("iommu: Add new flag to explictly request PASID capable domain")
Fixes: d68beb276ba2 ("iommu/arm-smmu-v3: Support IOMMU_HWPT_INVALIDATE using a VIOMMU object")
Link: https://patch.msgid.link/r/20241128035159.374624-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: 313e978df7fc ("ASoC: codecs: wcd937x: add audio routing and Kconfig")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-6-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: 250304a0fb34 ("ASoC: cs42l84: Add new codec driver")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: 3a513da1ae33 ("ASoC: SDCA: add initial module")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: 5bbfdad8cf8d ("ASoC: mediatek: Add MT8365 support")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should use *-y instead of *-objs in Makefile for the module
objects. *-objs is used rather for host programs.
Fixes: c486def5b3ba ("ASoC: cs40l50: Support I2S streaming to CS40L50")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241203141823.22393-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add ZSC Control register programming sequence for ACP D0 and D3 state
transitions for ACP6.3 platform. This will allow ACP to enter low power
state when ACP enters D3 state. When ACP enters D0 State, ZSC control
should be disabled.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20241203081940.3390281-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update mach_params subsystem_rev with acp_rev variable for ACP6.3
platform.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20241203081940.3390281-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Each cpu DAI should associate with a widget. However, the topology might
not create the right number of DAI widgets for aggregated amps. And it
will cause NULL pointer deference.
Check that the DAI widget associated with the CPU DAI is valid to prevent
NULL pointer deference due to missing DAI widgets in topologies with
aggregated amps.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20241203104853.56956-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The recent conversion of show_interrupts() to seq_put_decimal_ull_width()
caused a formatting regression as it drops a previosuly existing space
separator.
Add it back by unconditionally inserting a space after the interrupt
counts and removing the extra leading space from the chip name prints.
Fixes: f9ed1f7c2e26 ("genirq/proc: Use seq_put_decimal_ull_width() for decimal values")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: David Wang <00107082@163.com>
Link: https://lore.kernel.org/all/87zfldt5g4.ffs@tglx
Closes: https://lore.kernel.org/all/4ce18851-6e9f-bbe-8319-cc5e69fb45c@linux-m68k.org
|
|
Add the missing description to fix the following warning:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/rnull_mod.o
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Acked-by: Andreas Hindborg <a.hindborg@kernel.org>
Link: https://lore.kernel.org/r/20241130094521.193924-1-fujita.tomonori@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Change the type of the res2 parameter in io_uring_cmd_done from ssize_t
to u64. This aligns the parameter type with io_req_set_cqe32_extra,
which expects u64 arguments.
The change eliminates potential issues on 32-bit architectures where
ssize_t might be 32-bit.
Only user of passing res2 is drivers/nvme/host/ioctl.c and it actually
passes u64.
Fixes: ee692a21e9bf ("fs,io_uring: add infrastructure for uring-cmd")
Cc: stable@vger.kernel.org
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Tested-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Link: https://lore.kernel.org/r/20241203-io_uring_cmd_done-res2-as-u64-v2-1-5e59ae617151@ddn.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
a bus
Use snd_soc_dai_set_tdm_slot() on capture DAIs to prevent multiple
aggregated amps from trying to send data at the same time.
When the capture DAIs of multiple amps on a bus are aggregated they will
all be sharing the same bit slots for transmitted audio. This would lead
to bus errors if all channels on all amps were enabled, because multiple
amps would be trying to send data at the same time.
To prevent this, the available channels are divided between the amps on a
bus so that only one amp will be sending data for each channel position.
A CS35L56 has 4 TX channels, which must be split between all the amps on a
bus so that no two amps are using the same channel. This is done simply by
dividing by the number of amps on the bus, so that 1 amp can use all
4 channels, 2 amps can use 2 channels each, and 3 or 4 amps can only use
1 channel each.
The amps are usually aggregated across multiple SoundWire buses. In this
case there will be multiple cpu DAIs in the dailink. The channel mapping
is used to determine which amps are on each bus. The allocation of the
4 channels is done separately for each bus (only amps on the same bus can
interfere with each other).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241203104534.56719-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch splits the SoundWire capture DP into a separate DAI so that
it can be independently routed and/or aggregated. It also makes
corresponding changes to the SOF SoundWire machine driver.
The playback and capture over SoundWire are separate DPs so don't have to
route to the same place. They could also be aggregated differently - for
example the playback DP could be aggregated with a playback-only DAI on
a codec.
No production device currently uses the capture path and their topologies
do not connect it. So there is no need to change the machine driver match
table entries for these. They will simply drop the unused capture DAI.
There is one hookup used for a non-production development board that was
added by commit 05fe62842804 ("ASoC: Intel: soc-acpi-intel-mtl-match: add
acpi match table for cdb35l56-eight-c") This is the only hookup using a
topology that connects the SoundWire DP for capture, so this hookup has
been changed to include an aggregated endpoint for the capture DAI.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241203104534.56719-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When we enable lockdep we get such a warning:
=============================
WARNING: suspicious RCU usage
6.12.0-rc7+ #1891 Tainted: G W
-----------------------------
arch/loongarch/kvm/../../../virt/kvm/kvm_main.c:5945 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by qemu-system-loo/948:
#0: 90000001184a00a8 (&vcpu->mutex){+.+.}-{4:4}, at: kvm_vcpu_ioctl+0xf4/0xe20 [kvm]
stack backtrace:
CPU: 2 UID: 0 PID: 948 Comm: qemu-system-loo Tainted: G W 6.12.0-rc7+ #1891
Tainted: [W]=WARN
Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022
Stack : 0000000000000089 9000000005a0db9c 90000000071519c8 900000012c578000
900000012c57b940 0000000000000000 900000012c57b948 9000000007e53788
900000000815bcc8 900000000815bcc0 900000012c57b7b0 0000000000000001
0000000000000001 4b031894b9d6b725 0000000005dec000 9000000100427b00
00000000000003d2 0000000000000001 000000000000002d 0000000000000003
0000000000000030 00000000000003b4 0000000005dec000 0000000000000000
900000000806d000 9000000007e53788 00000000000000b4 0000000000000004
0000000000000004 0000000000000000 0000000000000000 9000000107baf600
9000000008916000 9000000007e53788 9000000005924778 000000001fe001e5
00000000000000b0 0000000000000007 0000000000000000 0000000000071c1d
...
Call Trace:
[<9000000005924778>] show_stack+0x38/0x180
[<90000000071519c4>] dump_stack_lvl+0x94/0xe4
[<90000000059eb754>] lockdep_rcu_suspicious+0x194/0x240
[<ffff80000221f47c>] kvm_io_bus_read+0x19c/0x1e0 [kvm]
[<ffff800002225118>] kvm_emu_mmio_read+0xd8/0x440 [kvm]
[<ffff8000022254bc>] kvm_handle_read_fault+0x3c/0xe0 [kvm]
[<ffff80000222b3c8>] kvm_handle_exit+0x228/0x480 [kvm]
Fix it by protecting kvm_io_bus_{read,write}() with SRCU.
Cc: stable@vger.kernel.org
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The BCM2836 interrupt controller doesn't provide any facility to configure
the wakeup sources. That's the reason why the driver lacks the
irq_set_wake() callback for the interrupt chip.
Enable the flags IRQCHIP_SKIP_SET_WAKE and IRQCHIP_MASK_ON_SUSPEND so the
interrupt suspend logic can handle the chip correctly equivalently to the
corresponding bcm2835 change (9a58480e5e53 ("irqchip/bcm2835: Enable
SKIP_SET_WAKE and MASK_ON_SUSPEND").
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/all/20241202115437.33552-1-wahrenst@gmx.net
|
|
When the GIC is in EOImode == 1 in irq_complete_ack() it executes a
priority drop not a deactivation.
Fix the function comment to clarify the behaviour.
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241202112518.51178-1-lpieralisi@kernel.org
|
|
Blamed commit forgot to change hsr_init_skb() to allocate
larger skb for RedBox case.
Indeed, send_hsr_supervision_frame() will add
two additional components (struct hsr_sup_tlv
and struct hsr_sup_payload)
syzbot reported the following crash:
skbuff: skb_over_panic: text:ffffffff8afd4b0a len:34 put:6 head:ffff88802ad29e00 data:ffff88802ad29f22 tail:0x144 end:0x140 dev:gretap0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:206 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
CPU: 2 UID: 0 PID: 7611 Comm: syz-executor Not tainted 6.12.0-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:skb_panic+0x157/0x1d0 net/core/skbuff.c:206
Code: b6 04 01 84 c0 74 04 3c 03 7e 21 8b 4b 70 41 56 45 89 e8 48 c7 c7 a0 7d 9b 8c 41 57 56 48 89 ee 52 4c 89 e2 e8 9a 76 79 f8 90 <0f> 0b 4c 89 4c 24 10 48 89 54 24 08 48 89 34 24 e8 94 76 fb f8 4c
RSP: 0018:ffffc90000858ab8 EFLAGS: 00010282
RAX: 0000000000000087 RBX: ffff8880598c08c0 RCX: ffffffff816d3e69
RDX: 0000000000000000 RSI: ffffffff816de786 RDI: 0000000000000005
RBP: ffffffff8c9b91c0 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000302 R11: ffffffff961cc1d0 R12: ffffffff8afd4b0a
R13: 0000000000000006 R14: ffff88804b938130 R15: 0000000000000140
FS: 000055558a3d6500(0000) GS:ffff88806a800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1295974ff8 CR3: 000000002ab6e000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
skb_over_panic net/core/skbuff.c:211 [inline]
skb_put+0x174/0x1b0 net/core/skbuff.c:2617
send_hsr_supervision_frame+0x6fa/0x9e0 net/hsr/hsr_device.c:342
hsr_proxy_announce+0x1a3/0x4a0 net/hsr/hsr_device.c:436
call_timer_fn+0x1a0/0x610 kernel/time/timer.c:1794
expire_timers kernel/time/timer.c:1845 [inline]
__run_timers+0x6e8/0x930 kernel/time/timer.c:2419
__run_timer_base kernel/time/timer.c:2430 [inline]
__run_timer_base kernel/time/timer.c:2423 [inline]
run_timer_base+0x111/0x190 kernel/time/timer.c:2439
run_timer_softirq+0x1a/0x40 kernel/time/timer.c:2449
handle_softirqs+0x213/0x8f0 kernel/softirq.c:554
__do_softirq kernel/softirq.c:588 [inline]
invoke_softirq kernel/softirq.c:428 [inline]
__irq_exit_rcu kernel/softirq.c:637 [inline]
irq_exit_rcu+0xbb/0x120 kernel/softirq.c:649
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1049 [inline]
sysvec_apic_timer_interrupt+0xa4/0xc0 arch/x86/kernel/apic/apic.c:1049
</IRQ>
Fixes: 5055cccfc2d1 ("net: hsr: Provide RedBox support (HSR-SAN)")
Reported-by: syzbot+7f4643b267cc680bfa1c@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lukasz Majewski <lukma@denx.de>
Link: https://patch.msgid.link/20241202100558.507765-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently rtnl_link_get_net_ifla() gets called twice when we create
peer devices, once in rtnl_add_peer_net() and once in each ->newlink()
implementation.
This looks safer, however, it leads to a classic Time-of-Check to
Time-of-Use (TOCTOU) bug since IFLA_NET_NS_PID is very dynamic. And
because of the lack of checking error pointer of the second call, it
also leads to a kernel crash as reported by syzbot.
Fix this by getting rid of the second call, which already becomes
redudant after Kuniyuki's work. We have to propagate the result of the
first rtnl_link_get_net_ifla() down to each ->newlink().
Reported-by: syzbot+21ba4d5adff0b6a7cfc6@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=21ba4d5adff0b6a7cfc6
Fixes: 0eb87b02a705 ("veth: Set VETH_INFO_PEER to veth_link_ops.peer_type.")
Fixes: 6b84e558e95d ("vxcan: Set VXCAN_INFO_PEER to vxcan_link_ops.peer_type.")
Fixes: fefd5d082172 ("netkit: Set IFLA_NETKIT_PEER_INFO to netkit_link_ops.peer_type.")
Cc: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241129212519.825567-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 43645ce03e00 ("qed: Populate nvm image attribute shadow.")
added support for populating flash image attributes, notably
"num_images". However, some cards were not able to return this
information. In such cases, the driver would return EINVAL, causing the
driver to exit.
Add check to return EOPNOTSUPP instead of EINVAL when the card is not
able to return these information. The caller function already handles
EOPNOTSUPP without error.
Fixes: 43645ce03e00 ("qed: Populate nvm image attribute shadow.")
Co-developed-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Florian Forestier <florian@forestier.re>
Signed-off-by: Louis Leseur <louis.leseur@gmail.com>
Link: https://patch.msgid.link/20241128083633.26431-1-louis.leseur@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Wen Gu says:
====================
two fixes for SMC
This patch set contains two bugfixes, to fix SMC warning and panic
issues in race conditions.
====================
Link: https://patch.msgid.link/20241127133014.100509-1-guwen@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We encountered a LGR/link use-after-free issue, which manifested as
the LGR/link refcnt reaching 0 early and entering the clear process,
making resource access unsafe.
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 14 PID: 107447 at lib/refcount.c:25 refcount_warn_saturate+0x9c/0x140
Workqueue: events smc_lgr_terminate_work [smc]
Call trace:
refcount_warn_saturate+0x9c/0x140
__smc_lgr_terminate.part.45+0x2a8/0x370 [smc]
smc_lgr_terminate_work+0x28/0x30 [smc]
process_one_work+0x1b8/0x420
worker_thread+0x158/0x510
kthread+0x114/0x118
or
refcount_t: underflow; use-after-free.
WARNING: CPU: 6 PID: 93140 at lib/refcount.c:28 refcount_warn_saturate+0xf0/0x140
Workqueue: smc_hs_wq smc_listen_work [smc]
Call trace:
refcount_warn_saturate+0xf0/0x140
smcr_link_put+0x1cc/0x1d8 [smc]
smc_conn_free+0x110/0x1b0 [smc]
smc_conn_abort+0x50/0x60 [smc]
smc_listen_find_device+0x75c/0x790 [smc]
smc_listen_work+0x368/0x8a0 [smc]
process_one_work+0x1b8/0x420
worker_thread+0x158/0x510
kthread+0x114/0x118
It is caused by repeated release of LGR/link refcnt. One suspect is that
smc_conn_free() is called repeatedly because some smc_conn_free() from
server listening path are not protected by sock lock.
e.g.
Calls under socklock | smc_listen_work
-------------------------------------------------------
lock_sock(sk) | smc_conn_abort
smc_conn_free | \- smc_conn_free
\- smcr_link_put | \- smcr_link_put (duplicated)
release_sock(sk)
So here add sock lock protection in smc_listen_work() path, making it
exclusive with other connection operations.
Fixes: 3b2dec2603d5 ("net/smc: restructure client and server code in af_smc")
Co-developed-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com>
Co-developed-by: Kai <KaiShen@linux.alibaba.com>
Signed-off-by: Kai <KaiShen@linux.alibaba.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We encountered a warning that close_work was canceled before
initialization.
WARNING: CPU: 7 PID: 111103 at kernel/workqueue.c:3047 __flush_work+0x19e/0x1b0
Workqueue: events smc_lgr_terminate_work [smc]
RIP: 0010:__flush_work+0x19e/0x1b0
Call Trace:
? __wake_up_common+0x7a/0x190
? work_busy+0x80/0x80
__cancel_work_timer+0xe3/0x160
smc_close_cancel_work+0x1a/0x70 [smc]
smc_close_active_abort+0x207/0x360 [smc]
__smc_lgr_terminate.part.38+0xc8/0x180 [smc]
process_one_work+0x19e/0x340
worker_thread+0x30/0x370
? process_one_work+0x340/0x340
kthread+0x117/0x130
? __kthread_cancel_work+0x50/0x50
ret_from_fork+0x22/0x30
This is because when smc_close_cancel_work is triggered, e.g. the RDMA
driver is rmmod and the LGR is terminated, the conn->close_work is
flushed before initialization, resulting in WARN_ON(!work->func).
__smc_lgr_terminate | smc_connect_{rdma|ism}
-------------------------------------------------------------
| smc_conn_create
| \- smc_lgr_register_conn
for conn in lgr->conns_all |
\- smc_conn_kill |
\- smc_close_active_abort |
\- smc_close_cancel_work |
\- cancel_work_sync |
\- __flush_work |
(close_work) |
| smc_close_init
| \- INIT_WORK(&close_work)
So fix this by initializing close_work before establishing the
connection.
Fixes: 46c28dbd4c23 ("net/smc: no socket state changes in tasklet context")
Fixes: 413498440e30 ("net/smc: add SMC-D support in af_smc")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Adding lockdep checking to the coredump code showed that there was an
existing violation. The dev_coredumpm_timeout() call is used to
register the dump with the base coredump subsystem. However, that
makes multiple memory allocations, only some of which use the GFP_
flags passed in. So that also needs to be deferred to the worker
function where it is safe to allocate with arbitrary flags.
In order to not add protoypes for the callback functions, moving the
_timeout call also means moving the worker thread function to later in
the file.
v2: Rebased after other changes to the worker function.
Fixes: e799485044cb ("drm/xe: Introduce the dev_coredump infrastructure.")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Francois Dugast <francois.dugast@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: "Thomas Hellström" <thomas.hellstrom@linux.intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: intel-xe@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: <stable@vger.kernel.org> # v6.8+
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241128210824.3302147-3-John.C.Harrison@Intel.com
(cherry picked from commit 90f51a7f4ec1004fc4ddfbc6d1f1068d85ef4771)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Fix missing initial value for last_value.
For GuC capture register definition, it is required to define 64bit
register in a pair of 2 consecutive 32bit register entries, low first,
then hi. Add code to check this order.
Changes from prior revs:
v5:- Correct cross-line comment format
v4:- Fix warn on condition and remove skipping
v3:- Move break inside brace
v2:- Correct the fix tag pointed commit
Add examples in comments for warning
Add 1 missing hi condition check
Fixes: ecb633646391 ("drm/xe/guc: Plumb GuC-capture into dev coredump")
Signed-off-by: Zhanjun Dong <zhanjun.dong@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241126201052.1937079-1-zhanjun.dong@intel.com
(cherry picked from commit 6f59fbcfa041e7d69e5e5f39d4c8cffa06fdc50b)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
syzkaller reported a use-after-free of UDP kernel socket
in cleanup_bearer() without repro. [0][1]
When bearer_disable() calls tipc_udp_disable(), cleanup
of the UDP kernel socket is deferred by work calling
cleanup_bearer().
tipc_net_stop() waits for such works to finish by checking
tipc_net(net)->wq_count. However, the work decrements the
count too early before releasing the kernel socket,
unblocking cleanup_net() and resulting in use-after-free.
Let's move the decrement after releasing the socket in
cleanup_bearer().
[0]:
ref_tracker: net notrefcnt@000000009b3d1faf has 1/1 users at
sk_alloc+0x438/0x608
inet_create+0x4c8/0xcb0
__sock_create+0x350/0x6b8
sock_create_kern+0x58/0x78
udp_sock_create4+0x68/0x398
udp_sock_create+0x88/0xc8
tipc_udp_enable+0x5e8/0x848
__tipc_nl_bearer_enable+0x84c/0xed8
tipc_nl_bearer_enable+0x38/0x60
genl_family_rcv_msg_doit+0x170/0x248
genl_rcv_msg+0x400/0x5b0
netlink_rcv_skb+0x1dc/0x398
genl_rcv+0x44/0x68
netlink_unicast+0x678/0x8b0
netlink_sendmsg+0x5e4/0x898
____sys_sendmsg+0x500/0x830
[1]:
BUG: KMSAN: use-after-free in udp_hashslot include/net/udp.h:85 [inline]
BUG: KMSAN: use-after-free in udp_lib_unhash+0x3b8/0x930 net/ipv4/udp.c:1979
udp_hashslot include/net/udp.h:85 [inline]
udp_lib_unhash+0x3b8/0x930 net/ipv4/udp.c:1979
sk_common_release+0xaf/0x3f0 net/core/sock.c:3820
inet_release+0x1e0/0x260 net/ipv4/af_inet.c:437
inet6_release+0x6f/0xd0 net/ipv6/af_inet6.c:489
__sock_release net/socket.c:658 [inline]
sock_release+0xa0/0x210 net/socket.c:686
cleanup_bearer+0x42d/0x4c0 net/tipc/udp_media.c:819
process_one_work kernel/workqueue.c:3229 [inline]
process_scheduled_works+0xcaf/0x1c90 kernel/workqueue.c:3310
worker_thread+0xf6c/0x1510 kernel/workqueue.c:3391
kthread+0x531/0x6b0 kernel/kthread.c:389
ret_from_fork+0x60/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:244
Uninit was created at:
slab_free_hook mm/slub.c:2269 [inline]
slab_free mm/slub.c:4580 [inline]
kmem_cache_free+0x207/0xc40 mm/slub.c:4682
net_free net/core/net_namespace.c:454 [inline]
cleanup_net+0x16f2/0x19d0 net/core/net_namespace.c:647
process_one_work kernel/workqueue.c:3229 [inline]
process_scheduled_works+0xcaf/0x1c90 kernel/workqueue.c:3310
worker_thread+0xf6c/0x1510 kernel/workqueue.c:3391
kthread+0x531/0x6b0 kernel/kthread.c:389
ret_from_fork+0x60/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:244
CPU: 0 UID: 0 PID: 54 Comm: kworker/0:2 Not tainted 6.12.0-rc1-00131-gf66ebf37d69c #7 91723d6f74857f70725e1583cba3cf4adc716cfa
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: events cleanup_bearer
Fixes: 26abe14379f8 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241127050512.28438-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If dccp_feat_push_confirm() fails after new value for SP feature was accepted
without reconciliation ('entry == NULL' branch), memory allocated for that value
with dccp_feat_clone_sp_val() is never freed.
Here is the kmemleak stack for this:
unreferenced object 0xffff88801d4ab488 (size 8):
comm "syz-executor310", pid 1127, jiffies 4295085598 (age 41.666s)
hex dump (first 8 bytes):
01 b4 4a 1d 80 88 ff ff ..J.....
backtrace:
[<00000000db7cabfe>] kmemdup+0x23/0x50 mm/util.c:128
[<0000000019b38405>] kmemdup include/linux/string.h:465 [inline]
[<0000000019b38405>] dccp_feat_clone_sp_val net/dccp/feat.c:371 [inline]
[<0000000019b38405>] dccp_feat_clone_sp_val net/dccp/feat.c:367 [inline]
[<0000000019b38405>] dccp_feat_change_recv net/dccp/feat.c:1145 [inline]
[<0000000019b38405>] dccp_feat_parse_options+0x1196/0x2180 net/dccp/feat.c:1416
[<00000000b1f6d94a>] dccp_parse_options+0xa2a/0x1260 net/dccp/options.c:125
[<0000000030d7b621>] dccp_rcv_state_process+0x197/0x13d0 net/dccp/input.c:650
[<000000001f74c72e>] dccp_v4_do_rcv+0xf9/0x1a0 net/dccp/ipv4.c:688
[<00000000a6c24128>] sk_backlog_rcv include/net/sock.h:1041 [inline]
[<00000000a6c24128>] __release_sock+0x139/0x3b0 net/core/sock.c:2570
[<00000000cf1f3a53>] release_sock+0x54/0x1b0 net/core/sock.c:3111
[<000000008422fa23>] inet_wait_for_connect net/ipv4/af_inet.c:603 [inline]
[<000000008422fa23>] __inet_stream_connect+0x5d0/0xf70 net/ipv4/af_inet.c:696
[<0000000015b6f64d>] inet_stream_connect+0x53/0xa0 net/ipv4/af_inet.c:735
[<0000000010122488>] __sys_connect_file+0x15c/0x1a0 net/socket.c:1865
[<00000000b4b70023>] __sys_connect+0x165/0x1a0 net/socket.c:1882
[<00000000f4cb3815>] __do_sys_connect net/socket.c:1892 [inline]
[<00000000f4cb3815>] __se_sys_connect net/socket.c:1889 [inline]
[<00000000f4cb3815>] __x64_sys_connect+0x6e/0xb0 net/socket.c:1889
[<00000000e7b1e839>] do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
[<0000000055e91434>] entry_SYSCALL_64_after_hwframe+0x67/0xd1
Clean up the allocated memory in case of dccp_feat_push_confirm() failure
and bail out with an error reset code.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: e77b8363b2ea ("dccp: Process incoming Change feature-negotiation options")
Signed-off-by: Ivan Solodovnikov <solodovnikov.ia@phystech.edu>
Link: https://patch.msgid.link/20241126143902.190853-1-solodovnikov.ia@phystech.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Dst objects get leaked in ip6_negative_advice() when this function is
executed for an expired IPv6 route located in the exception table. There
are several conditions that must be fulfilled for the leak to occur:
* an ICMPv6 packet indicating a change of the MTU for the path is received,
resulting in an exception dst being created
* a TCP connection that uses the exception dst for routing packets must
start timing out so that TCP begins retransmissions
* after the exception dst expires, the FIB6 garbage collector must not run
before TCP executes ip6_negative_advice() for the expired exception dst
When TCP executes ip6_negative_advice() for an exception dst that has
expired and if no other socket holds a reference to the exception dst, the
refcount of the exception dst is 2, which corresponds to the increment
made by dst_init() and the increment made by the TCP socket for which the
connection is timing out. The refcount made by the socket is never
released. The refcount of the dst is decremented in sk_dst_reset() but
that decrement is counteracted by a dst_hold() intentionally placed just
before the sk_dst_reset() in ip6_negative_advice(). After
ip6_negative_advice() has finished, there is no other object tied to the
dst. The socket lost its reference stored in sk_dst_cache and the dst is
no longer in the exception table. The exception dst becomes a leaked
object.
As a result of this dst leak, an unbalanced refcount is reported for the
loopback device of a net namespace being destroyed under kernels that do
not contain e5f80fcf869a ("ipv6: give an IPv6 dev to blackhole_netdev"):
unregister_netdevice: waiting for lo to become free. Usage count = 2
Fix the dst leak by removing the dst_hold() in ip6_negative_advice(). The
patch that introduced the dst_hold() in ip6_negative_advice() was
92f1655aa2b22 ("net: fix __dst_negative_advice() race"). But 92f1655aa2b22
merely refactored the code with regards to the dst refcount so the issue
was present even before 92f1655aa2b22. The bug was introduced in
54c1a859efd9f ("ipv6: Don't drop cache route entry unless timer actually
expired.") where the expired cached route is deleted and the sk_dst_cache
member of the socket is set to NULL by calling dst_negative_advice() but
the refcount belonging to the socket is left unbalanced.
The IPv4 version - ipv4_negative_advice() - is not affected by this bug.
When the TCP connection times out ipv4_negative_advice() merely resets the
sk_dst_cache of the socket while decrementing the refcount of the
exception dst.
Fixes: 92f1655aa2b22 ("net: fix __dst_negative_advice() race")
Fixes: 54c1a859efd9f ("ipv6: Don't drop cache route entry unless timer actually expired.")
Link: https://lore.kernel.org/netdev/20241113105611.GA6723@incl/T/#u
Signed-off-by: Jiri Wiesner <jwiesner@suse.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241128085950.GA4505@incl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LAN7800/7850
Fix outdated MII_LPA data in the LAN88xx PHY, which is used in LAN7800
and LAN7850 USB Ethernet controllers. Due to a hardware limitation, the
PHY cannot reliably update link status after parallel detection when the
link partner does not support auto-negotiation. To mitigate this, add a
PHY reset in `lan88xx_link_change_notify()` when `phydev->state` is
`PHY_NOLINK`, ensuring the PHY starts in a clean state and reports
accurate fixed link parallel detection results.
Fixes: 792aec47d59d9 ("add microchip LAN88xx phy driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241125084050.414352-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
