| Age | Commit message (Collapse) | Author |
|---|
|
snd_una update should not be done when the same skb is being
sent out.chcr_short_record_handler() sends it again even
though SND_UNA update is already sent for the skb in
chcr_ktls_xmit(), which causes mismatch in un-acked
TCP seq number, later causes problem in sending out
complete record.
Fixes: 429765a149f1 ("chcr: handle partial end part of a record")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW doesn't need marking TCB closed. This TCB state change
sometimes causes problem to the new connection which gets
the same tid.
Fixes: 34aba2c45024 ("cxgb4/chcr : Register to tls add and del callback")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sge queue is full and chcr_ktls_xmit_wr_complete()
returns failure, skb is not freed if it is not the last tls record in
this skb, causes refcount never gets freed and tls_dev_del()
never gets called on this connection.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking page refcount is not ideal and causes kernel panic
sometimes. It's better to take tx_ctx lock for the complete
skb transmit, to avoid page cleanup if ACK received in middle.
Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert system_wq queue_work() to schedule_work() which is
a wrapper around it, since the former is a rare construct.
Fixes: 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Huazhong Tan says:
====================
net: hns3: updates for -next
This series adds support for pushing link status to VFs for
the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.
To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.
The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.
Select the copper page when probing to circumvent this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-04-14
This series contains updates to ice driver only.
Bruce changes and removes open coded values to instead use existing
kernel defines and suppresses false cppcheck issues.
Ani adds new VSI states to track netdev allocation and registration. He
also removes leading underscores in the ice_pf_state enum.
Jesse refactors ITR by introducing helpers to reduce duplicated code and
structures to simplify checking of ITR mode. He also triggers a software
interrupt when exiting napi poll or busy-poll to ensure all work is
processed. Modifies /proc/iomem to display driver name instead of PCI
address. He also changes the checks of vsi->type to use a local variable
in ice_vsi_rebuild() and removes an unneeded struct member.
Jake replaces the driver's adaptive interrupt moderation algorithm to
use the kernel's DIM library implementation.
Scott reworks module reads to reduce the number of reads needed and
remove excessive increment of QSFP page.
Brett sets the vsi->vf_id to invalid for non-VF VSIs.
Paul removes the return value from ice_vsi_manage_rss_lut() as it's not
communicating anything critical. He also reduces the scope of a
variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-04-14
This series provides 3 small fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f48 ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Restore the initrd-based ACPI table override functionality broken by
one of the recent fixes"
* tag 'acpi-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: x86: Call acpi_boot_table_init() after acpi_table_upgrade()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"A single fix for an older problem with the sysfs interface: do not
allow exporting GPIO lines which were marked invalid by the driver"
* tag 'gpio-fixes-for-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sysfs: Obey valid_mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"The changes are all device/driver specific fixes:
- EV_KEY and EV_ABS regression fix for Wacom from Ping Cheng
- BIOS-specific quirk to fix some of the AMD_SFH-based systems, from
Hans de Goede
- other small error handling fixes and device ID additions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: wacom: set EV_KEY and EV_ABS only for non-HID_GENERIC type of devices
AMD_SFH: Add DMI quirk table for BIOS-es which don't set the activestatus bits
AMD_SFH: Add sensor_mask module parameter
AMD_SFH: Removed unused activecontrolstatus member from the amd_mp2_dev struct
HID: wacom: Assign boolean values to a bool variable
HID cp2112: fix support for multiple gpiochips
HID: alps: fix error return code in alps_input_configured()
HID: asus: Add support for 2021 ASUS N-Key keyboard
HID: google: add don USB id
|
|
After commit 2decad92f473 ("arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is
set atomically"), LLVM's integrated assembler fails to build entry.S:
<instantiation>:5:7: error: expected assembly-time absolute expression
.org . - (664b-663b) + (662b-661b)
^
<instantiation>:6:7: error: expected assembly-time absolute expression
.org . - (662b-661b) + (664b-663b)
^
The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.
Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Cc: <stable@vger.kernel.org> # 5.8.x
Link: https://github.com/ClangBuiltLinux/linux/issues/1347
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a few driver fixes here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - drop zero-checking of ABS_MT_TOUCH_MAJOR resolution
Input: elants_i2c - fix division by zero if firmware reports zero phys size
Input: nspire-keypad - enable interrupts only when opened
Input: i8042 - fix Pegatron C15B ID entry
Input: n64joy - fix return value check in n64joy_probe()
Input: s6sy761 - fix coordinate read bit shift
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Display panel & power related fixes:
- Backlight fix (Lyude)
- Display watermark fix (Ville)
- VLV panel power fix (Hans)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YHg4nz/ndzDRmPjd@intel.com
|
|
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the nft_offload there is the mate flow_dissector with no
ingress_ifindex but with ingress_iftype that only be used
in the software. So if the mask of ingress_ifindex in meta is
0, this meta check should be bypass.
Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Change register setting from bit number to bit mask.
Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prevent setting of devlink traps on the uplink while in switchdev mode.
In this mode, it is the SW switch responsibility to handle both packets
with a mismatch in destination MAC or VLAN ID. Therefore, there are no
flow steering tables to trap undesirable packets and driver crashes upon
setting a trap.
Fixes: 241dc159391f ("net/mlx5: Notify on trap action by blocking event")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-04-14
this is a pull request of a single patch for net-next/master.
Vincent Mailhol's patch fixes a NULL pointer dereference when handling
error frames in the etas_es58x driver, which has been added in the
previous PR.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
af_packet fanout uses RCU rules to ensure f->arr elements
are not dismantled before RCU grace period.
However, it lacks rcu accessors to make sure KCSAN and other tools
wont detect data races. Stupid compilers could also play games.
Fixes: dc99f600698d ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.
Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-13
mlx5 core and netdev driver updates
1) E-Switch updates from Parav,
1.1) Devlink parameter to control mlx5 metadata enablement for E-Switch
1.2) Trivial cleanups for E-Switch code
1.3) Dynamically allocate vport steering namespaces only when required
2) From Jianbo, Use variably sized data structures for Software steering
3) Several minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-14
This series contains updates to ixgbe and ice drivers.
Alex Duyck fixes a NULL pointer dereference for ixgbe.
Yongxin Liu fixes an unbalanced enable/disable which was causing a call
trace with suspend for ixgbe.
Colin King fixes a potential infinite loop for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, the bootloader will already initialize the MAC address
registers of the ENETC and the driver will just use them or generate a
random one, if it is not initialized.
Add a new way to provide the MAC address: via device tree. Besides the
usual 'mac-address' property, there is also the possibility to fetch it
via a NVMEM provider. The sl28 board stores the MAC address in the SPI
NOR flash OTP region. Having this will allow linux to fetch the MAC
address from there without being dependent on the bootloader.
No in-tree boards have the device tree properties set, thus for these,
this is a no-op.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the commit 1ddc3229ad3c ("skbuff: remove some unnecessary operation
in skb_segment_list()") introduces an issue very similar to the
one already fixed by commit 53475c5dd856 ("net: fix use-after-free when
UDP GRO with shared fraglist").
If the GSO skb goes though skb_clone() and pskb_expand_head() before
entering skb_segment_list(), the latter will unshare the frag_list
skbs and will release the old list. With the reverted commit in place,
when skb_segment_list() completes, skb->next points to the just
released list, and later on the kernel will hit UaF.
Note that since commit e0e3070a9bc9 ("udp: properly complete L4 GRO
over UDP tunnel packet") the critical scenario can be reproduced also
receiving UDP over vxlan traffic with:
NIC (NETIF_F_GRO_FRAGLIST enabled) -> vxlan -> UDP sink
Attaching a packet socket to the NIC will cause skb_clone() and the
tunnel decapsulation will call pskb_expand_head().
Fixes: 1ddc3229ad3c ("skbuff: remove some unnecessary operation in skb_segment_list()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following clang warning:
drivers/atm/idt77252.c:1787:1: warning: unused function
'idt77252_fbq_level' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM verity target FEC support's RS roots IO to always be aligned.
This fixes a previous stable@ fix that overcorrected for a different
configuration that also resulted in misaligned roots IO"
* tag 'for-5.12/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix misaligned RS roots IO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2021-04-14
Not much this time:
1) Simplification of some variable calculations in esp4 and esp6.
From Jiapeng Chong and Junlin Yang.
2) Fix a clang Wformat warning in esp6 and ah6.
From Arnd Bergmann.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
