| Age | Commit message (Collapse) | Author |
|---|
|
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b758137601 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On gt reset, if a context is running, then accumulate it's active time
into the busyness counter since there will be no chance for the context
to switch out and update it's run time.
v2: Move comment right above the if (John)
Fixes: 77cdd054dd2c ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-4-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 7ed047da59cfa1acb558b95169d347acc8d85da1)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
Active busyness of an engine is calculated using gt timestamp and the
context switch in time. While capturing the gt timestamp, it's possible
that the context switches out. This race could result in an active
busyness value that is greater than the actual context runtime value by a
small amount. This leads to a negative delta and throws off busyness
calculations for the user.
If a subsequent count is smaller than the previous one, just return the
previous one, since we expect the busyness to catch up.
Fixes: 77cdd054dd2c ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-3-umesh.nerlige.ramappa@intel.com
(cherry picked from commit cf907f6d294217985e9dafd9985dce874e04ca37)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
On GT reset, we store total busyness counts for all engines and
re-register the utilization buffer with GuC. At that time we should
reset the buffer, so that we don't get spurious busyness counts on
subsequent queries.
To repro this issue, run igt@perf_pmu@busy-hang followed by
igt@perf_pmu@most-busy-idle-check-all for a couple iterations.
Fixes: 77cdd054dd2c ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241127174006.190128-2-umesh.nerlige.ramappa@intel.com
(cherry picked from commit abd318237fa6556c1e5225529af145ef15d5ff0d)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
|
|
The alias symbol name was renamed. Adjust module_phy_driver macro to
create the proper symbol name to fix module autoloading.
Fixes: 054a9cd395a7 ("modpost: rename alias symbol for MODULE_DEVICE_TABLE()")
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20241212130015.238863-1-fujita.tomonori@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The hypercall page is no longer needed. It can be removed, as from the
Xen perspective it is optional.
But, from Linux's perspective, it removes naked RET instructions that
escape the speculative protections that Call Depth Tracking and/or
Untrain Ret are trying to achieve.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
|
|
Call the Xen hypervisor via the new xen_hypercall_func static-call
instead of the hypercall page.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
|
|
Add generic hypercall functions usable for all normal (i.e. not iret)
hypercalls. Depending on the guest type and the processor vendor
different functions need to be used due to the to be used instruction
for entering the hypervisor:
- PV guests need to use syscall
- HVM/PVH guests on Intel need to use vmcall
- HVM/PVH guests on AMD and Hygon need to use vmmcall
As PVH guests need to issue hypercalls very early during boot, there
is a 4th hypercall function needed for HVM/PVH which can be used on
Intel and AMD processors. It will check the vendor type and then set
the Intel or AMD specific function to use via static_call().
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
|
|
There is a check for NULL at the start of create_txqs() and
create_rxqs() which tess if "nic_dev->txqs" is non-NULL. The
intention is that if the device is already open and the queues
are already created then we don't create them a second time.
However, the bug is that if we have an error in the create_txqs()
then the pointer doesn't get set back to NULL. The NULL check
at the start of the function will say that it's already open when
it's not and the device can't be used.
Set ->txqs back to NULL on cleanup on error.
Fixes: c3e79baf1b03 ("net-next/hinic: Add logical Txq and Rxq")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc98faf-a0ed-4565-a55b-0fa2734bc205@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Small follow-up to align this to an equivalent behavior as the bond driver.
The change in 3625920b62c3 ("teaming: fix vlan_features computing") removed
the netdevice vlan_features when there is no team port attached, yet it
leaves the full set of enc_features intact.
Instead, leave the default features as pre 3625920b62c3, and recompute once
we do have ports attached. Also, similarly as in bonding case, call the
netdev_base_features() helper on the enc_features.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241213123657.401868-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "gl->tot_len" variable is controlled by the user. It comes from
process_responses(). On 32bit systems, the "gl->tot_len +
sizeof(struct cpl_pass_accept_req) + sizeof(struct rss_header)" addition
could have an integer wrapping bug. Use size_add() to prevent this.
Fixes: a08943947873 ("crypto: chtls - Register chtls with net tls")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c6bfb23c-2db2-4e1b-b8ab-ba3925c82ef5@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jakub Kicinski says:
====================
netdev: fix repeated netlink messages in queue dumps
Fix dump continuation for queues and queue stats in the netdev family.
Because we used post-increment when saving id of dumped queue next
skb would re-dump the already dumped queue.
====================
Link: https://patch.msgid.link/20241213152244.3080955-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sanity check netlink dumps, to make sure dumps don't have
repeated entries or gaps in IDs.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20241213152244.3080955-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This test already catches a netlink bug fixed by this series,
but only when running on HW with many queues. Make sure the
netdevsim instance created has a lot of queues, and constrain
the size of the recv_buffer used by netlink.
While at it test both rx and tx queues.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20241213152244.3080955-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
recv_size parameter allows constraining the buffer size for dumps.
It's useful in testing kernel handling of dump continuation,
IOW testing dumps which span multiple skbs.
Let the tests set this parameter when initializing the YNL family.
Keep the normal default, we don't want tests to unintentionally
behave very differently than normal code.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/20241213152244.3080955-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The context is supposed to record the next queue to dump,
not last dumped. If the dump doesn't fit we will restart
from the already-dumped queue, duplicating the message.
Before this fix and with the selftest improvements later
in this series we see:
# ./run_kselftest.sh -t drivers/net:stats.py
timeout set to 45
selftests: drivers/net: stats.py
KTAP version 1
1..5
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 125, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), len(set(queues[qtype])),
# Check failed 45 != 44 repeated queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 127, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), max(queues[qtype]) + 1,
# Check failed 45 != 44 missing queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 125, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), len(set(queues[qtype])),
# Check failed 45 != 44 repeated queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 127, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), max(queues[qtype]) + 1,
# Check failed 45 != 44 missing queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 125, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), len(set(queues[qtype])),
# Check failed 103 != 100 repeated queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 127, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), max(queues[qtype]) + 1,
# Check failed 103 != 100 missing queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 125, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), len(set(queues[qtype])),
# Check failed 102 != 100 repeated queue keys
# Check| At /root/ksft-net-drv/drivers/net/./stats.py, line 127, in qstat_by_ifindex:
# Check| ksft_eq(len(queues[qtype]), max(queues[qtype]) + 1,
# Check failed 102 != 100 missing queue keys
not ok 4 stats.qstat_by_ifindex
ok 5 stats.check_down
# Totals: pass:4 fail:1 xfail:0 xpass:0 skip:0 error:0
With the fix:
# ./ksft-net-drv/run_kselftest.sh -t drivers/net:stats.py
timeout set to 45
selftests: drivers/net: stats.py
KTAP version 1
1..5
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum
ok 4 stats.qstat_by_ifindex
ok 5 stats.check_down
# Totals: pass:5 fail:0 xfail:0 xpass:0 skip:0 error:0
Fixes: ab63a2387cb9 ("netdev: add per-queue statistics")
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241213152244.3080955-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The context is supposed to record the next queue to dump,
not last dumped. If the dump doesn't fit we will restart
from the already-dumped queue, duplicating the message.
Before this fix and with the selftest improvements later
in this series we see:
# ./run_kselftest.sh -t drivers/net:queues.py
timeout set to 45
selftests: drivers/net: queues.py
KTAP version 1
1..2
# Check| At /root/ksft-net-drv/drivers/net/./queues.py, line 32, in get_queues:
# Check| ksft_eq(queues, expected)
# Check failed 102 != 100
# Check| At /root/ksft-net-drv/drivers/net/./queues.py, line 32, in get_queues:
# Check| ksft_eq(queues, expected)
# Check failed 101 != 100
not ok 1 queues.get_queues
ok 2 queues.addremove_queues
# Totals: pass:1 fail:1 xfail:0 xpass:0 skip:0 error:0
not ok 1 selftests: drivers/net: queues.py # exit=1
With the fix:
# ./ksft-net-drv/run_kselftest.sh -t drivers/net:queues.py
timeout set to 45
selftests: drivers/net: queues.py
KTAP version 1
1..2
ok 1 queues.get_queues
ok 2 queues.addremove_queues
# Totals: pass:2 fail:0 xfail:0 xpass:0 skip:0 error:0
Fixes: 6b6171db7fc8 ("netdev-genl: Add netlink framework functions for queue")
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241213152244.3080955-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove hard-coded strings by using the str_yes_no() helper function.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
GCC performs value range tracking for variables as a way to provide better
diagnostics. One place this is regularly seen is with warnings associated
with bounds-checking, e.g. -Wstringop-overflow, -Wstringop-overread,
-Warray-bounds, etc. In order to keep the signal-to-noise ratio high,
warnings aren't emitted when a value range spans the entire value range
representable by a given variable. For example:
unsigned int len;
char dst[8];
...
memcpy(dst, src, len);
If len's value is unknown, it has the full "unsigned int" range of [0,
UINT_MAX], and GCC's compile-time bounds checks against memcpy() will
be ignored. However, when a code path has been able to narrow the range:
if (len > 16)
return;
memcpy(dst, src, len);
Then the range will be updated for the execution path. Above, len is
now [0, 16] when reading memcpy(), so depending on other optimizations,
we might see a -Wstringop-overflow warning like:
error: '__builtin_memcpy' writing between 9 and 16 bytes into region of size 8 [-Werror=stringop-overflow]
When building with CONFIG_FORTIFY_SOURCE, the fortified run-time bounds
checking can appear to narrow value ranges of lengths for memcpy(),
depending on how the compiler constructs the execution paths during
optimization passes, due to the checks against the field sizes. For
example:
if (p_size_field != SIZE_MAX &&
p_size != p_size_field && p_size_field < size)
As intentionally designed, these checks only affect the kernel warnings
emitted at run-time and do not block the potentially overflowing memcpy(),
so GCC thinks it needs to produce a warning about the resulting value
range that might be reaching the memcpy().
We have seen this manifest a few times now, with the most recent being
with cpumasks:
In function ‘bitmap_copy’,
inlined from ‘cpumask_copy’ at ./include/linux/cpumask.h:839:2,
inlined from ‘__padata_set_cpumasks’ at kernel/padata.c:730:2:
./include/linux/fortify-string.h:114:33: error: ‘__builtin_memcpy’ reading between 257 and 536870904 bytes from a region of size 256 [-Werror=stringop-overread]
114 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:633:9: note: in expansion of macro ‘__underlying_memcpy’
633 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
./include/linux/fortify-string.h:678:26: note: in expansion of macro ‘__fortify_memcpy_chk’
678 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
./include/linux/bitmap.h:259:17: note: in expansion of macro ‘memcpy’
259 | memcpy(dst, src, len);
| ^~~~~~
kernel/padata.c: In function ‘__padata_set_cpumasks’:
kernel/padata.c:713:48: note: source object ‘pcpumask’ of size [0, 256]
713 | cpumask_var_t pcpumask,
| ~~~~~~~~~~~~~~^~~~~~~~
This warning is _not_ emitted when CONFIG_FORTIFY_SOURCE is disabled,
and with the recent -fdiagnostics-details we can confirm the origin of
the warning is due to FORTIFY's bounds checking:
../include/linux/bitmap.h:259:17: note: in expansion of macro 'memcpy'
259 | memcpy(dst, src, len);
| ^~~~~~
'__padata_set_cpumasks': events 1-2
../include/linux/fortify-string.h:613:36:
612 | if (p_size_field != SIZE_MAX &&
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
613 | p_size != p_size_field && p_size_field < size)
| ~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
| |
| (1) when the condition is evaluated to false
| (2) when the condition is evaluated to true
'__padata_set_cpumasks': event 3
114 | #define __underlying_memcpy __builtin_memcpy
| ^
| |
| (3) out of array bounds here
Note that the cpumask warning started appearing since bitmap functions
were recently marked __always_inline in commit ed8cd2b3bd9f ("bitmap:
Switch from inline to __always_inline"), which allowed GCC to gain
visibility into the variables as they passed through the FORTIFY
implementation.
In order to silence these false positives but keep otherwise deterministic
compile-time warnings intact, hide the length variable from GCC with
OPTIMIZE_HIDE_VAR() before calling the builtin memcpy.
Additionally add a comment about why all the macro args have copies with
const storage.
Reported-by: "Thomas Weißschuh" <linux@weissschuh.net>
Closes: https://lore.kernel.org/all/db7190c8-d17f-4a0d-bc2f-5903c79f36c2@t-8ch.de/
Reported-by: Nilay Shroff <nilay@linux.ibm.com>
Closes: https://lore.kernel.org/all/20241112124127.1666300-1-nilay@linux.ibm.com/
Tested-by: Nilay Shroff <nilay@linux.ibm.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Registers
The values returned by the driver after processing the contents of the
Temperature Result and the Temperature Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect.
According to the TMP512 and TMP513 datasheets, the Temperature Result (08h
to 0Bh) and Limit (11h to 14h) Registers are 13-bit two's complement
integer values, shifted left by 3 bits. The value is scaled by 0.0625
degrees Celsius per bit. E.g., if regval = 1 1110 0111 0000 000, the
output should be -25 degrees, but the driver will return +487 degrees.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-4-m.masimov@maxima.ru
[groeck: fixed description line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The value returned by the driver after processing the contents of the
Current Register does not correspond to the TMP512/TMP513 specifications.
A raw register value is converted to a signed integer value by a sign
extension in accordance with the algorithm provided in the specification,
but due to the off-by-one error in the sign bit index, the result is
incorrect. Moreover, negative values will be reported as large positive
due to missing sign extension from u32 to long.
According to the TMP512 and TMP513 datasheets, the Current Register (07h)
is a 16-bit two's complement integer value. E.g., if regval = 1000 0011
0000 0000, then the value must be (-32000 * lsb), but the driver will
return (33536 * lsb).
Fix off-by-one bug, and also cast data->curr_lsb_ua (which is of type u32)
to long to prevent incorrect cast for negative values.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-3-m.masimov@maxima.ru
[groeck: Fixed description line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Registers
The values returned by the driver after processing the contents of the
Shunt Voltage Register and the Shunt Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect. Moreover, the PGA shift calculated with
the tmp51x_get_pga_shift function is relevant only to the Shunt Voltage
Register, but is also applied to the Shunt Limit Registers.
According to the TMP512 and TMP513 datasheets, the Shunt Voltage Register
(04h) is 13 to 16 bit two's complement integer value, depending on the PGA
setting. The Shunt Positive (0Ch) and Negative (0Dh) Limit Registers are
16-bit two's complement integer values. Below are some examples:
* Shunt Voltage Register
If PGA = 8, and regval = 1000 0011 0000 0000, then the decimal value must
be -32000, but the value calculated by the driver will be 33536.
* Shunt Limit Register
If regval = 1000 0011 0000 0000, then the decimal value must be -32000, but
the value calculated by the driver will be 768, if PGA = 1.
Fix sign bit index, and also correct misleading comment describing the
tmp51x_get_pga_shift function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d82 ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-2-m.masimov@maxima.ru
[groeck: Fixed description and multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If mounted with sparseread option, ceph_direct_read_write() ends up
making an unnecessarily allocation for O_DIRECT writes.
Fixes: 03bc06c7b0bd ("ceph: add new mount option to enable sparse reads")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
|
|
The bvecs array which is allocated in iter_get_bvecs_alloc() is leaked
and pages remain pinned if ceph_alloc_sparse_ext_map() fails.
There is no need to delay the allocation of sparse_ext map until after
the bvecs array is set up, so fix this by moving sparse_ext allocation
a bit earlier. Also, make a similar adjustment in __ceph_sync_read()
for consistency (a leak of the same kind in __ceph_sync_read() has been
addressed differently).
Cc: stable@vger.kernel.org
Fixes: 03bc06c7b0bd ("ceph: add new mount option to enable sparse reads")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
|
|
This patch refines the read logic in __ceph_sync_read() to ensure more
predictable and efficient behavior in various edge cases.
- Return early if the requested read length is zero or if the file size
(`i_size`) is zero.
- Initialize the index variable (`idx`) where needed and reorder some
code to ensure it is always set before use.
- Improve error handling by checking for negative return values earlier.
- Remove redundant encrypted file checks after failures. Only attempt
filesystem-level decryption if the read succeeded.
- Simplify leftover calculations to correctly handle cases where the
read extends beyond the end of the file or stops short. This can be
hit by continuously reading a file while, on another client, we keep
truncating and writing new data into it.
- This resolves multiple issues caused by integer and consequent buffer
overflow (`pages` array being accessed beyond `num_pages`):
- https://tracker.ceph.com/issues/67524
- https://tracker.ceph.com/issues/68980
- https://tracker.ceph.com/issues/68981
Cc: stable@vger.kernel.org
Fixes: 1065da21e5df ("ceph: stop copying to iter at EOF on sync reads")
Reported-by: Luis Henriques (SUSE) <luis.henriques@linux.dev>
Signed-off-by: Alex Markuze <amarkuze@redhat.com>
Reviewed-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
It becomes a path component, so it shouldn't exceed NAME_MAX
characters. This was hardened in commit c152737be22b ("ceph: Use
strscpy() instead of strcpy() in __get_snap_name()"), but no actual
check was put in place.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
|
|
If the full path to be built by ceph_mdsc_build_path() happens to be
longer than PATH_MAX, then this function will enter an endless (retry)
loop, effectively blocking the whole task. Most of the machine
becomes unusable, making this a very simple and effective DoS
vulnerability.
I cannot imagine why this retry was ever implemented, but it seems
rather useless and harmful to me. Let's remove it and fail with
ENAMETOOLONG instead.
Cc: stable@vger.kernel.org
Reported-by: Dario Weißer <dario@cure53.de>
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
In two `break` statements, the call to ceph_release_page_vector() was
missing, leaking the allocation from ceph_alloc_page_vector().
Instead of adding the missing ceph_release_page_vector() calls, the
Ceph maintainers preferred to transfer page ownership to the
`ceph_osd_request` by passing `own_pages=true` to
osd_req_op_extent_osd_data_pages(). This requires postponing the
ceph_osdc_put_request() call until after the block that accesses the
`pages`.
Cc: stable@vger.kernel.org
Fixes: 03bc06c7b0bd ("ceph: add new mount option to enable sparse reads")
Fixes: f0fe1e54cfcf ("ceph: plumb in decryption during reads")
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
When function tracing and function graph tracing are both enabled (in
different instances) the "parent" of some of the function tracing events
is "return_to_handler" which is the trampoline used by function graph
tracing. To fix this, ftrace_get_true_parent_ip() was introduced that
returns the "true" parent ip instead of the trampoline.
To do this, the ftrace_regs_get_stack_pointer() is used, which uses
kernel_stack_pointer(). The problem is that microblaze does not implement
kerenl_stack_pointer() so when function graph tracing is enabled, the
build fails. But microblaze also does not enabled HAVE_DYNAMIC_FTRACE_WITH_ARGS.
That option has to be enabled by the architecture to reliably get the
values from the fregs parameter passed in. When that config is not set,
the architecture can also pass in NULL, which is not tested for in that
function and could cause the kernel to crash.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jeff Xie <jeff.xie@linux.dev>
Link: https://lore.kernel.org/20241216164633.6df18e87@gandalf.local.home
Fixes: 60b1f578b578 ("ftrace: Get the true parent ip for function tracer")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
A bug was discovered where the idle shadow stacks were not initialized
for offline CPUs when starting function graph tracer, and when they came
online they were not traced due to the missing shadow stack. To fix
this, the idle task shadow stack initialization was moved to using the
CPU hotplug callbacks. But it removed the initialization when the
function graph was enabled. The problem here is that the hotplug
callbacks are called when the CPUs come online, but the idle shadow
stack initialization only happens if function graph is currently
active. This caused the online CPUs to not get their shadow stack
initialized.
The idle shadow stack initialization still needs to be done when the
function graph is registered, as they will not be allocated if function
graph is not registered.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20241211135335.094ba282@batman.local.home
Fixes: 2c02f7375e65 ("fgraph: Use CPU hotplug mechanism to initialize idle shadow stacks")
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Closes: https://lore.kernel.org/all/CACRpkdaTBrHwRbbrphVy-=SeDz6MSsXhTKypOtLrTQ+DgGAOcQ@mail.gmail.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The macros giving the direction of the crossing thresholds use the BIT
macro which is not exported to the userspace. Consequently when an
userspace program includes the header, it fails to compile.
Replace the macros by their litteral to allow the compilation of
userspace program using this header.
Fixes: 445936f9e258 ("thermal: core: Add user thresholds support")
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://patch.msgid.link/20241212201311.4143196-1-daniel.lezcano@linaro.org
[ rjw: Add Fixes: ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Three small fixes for the soc tree:
- devicetee fix for the Arm Juno reference machine, to allow more
interesting PCI configurations
- build fix for SCMI firmware on the NXP i.MX platform
- fix for a race condition in Arm FF-A firmware"
* tag 'soc-fixes-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: fvp: Update PCIe bus-range property
firmware: arm_ffa: Fix the race around setting ffa_dev->properties
firmware: arm_scmi: Fix i.MX build dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Ilpo Järvinen:
- alienware-wmi:
- Add support for Alienware m16 R1 AMD
- Do not setup legacy LED control with X and G Series
- intel/ifs: Clearwater Forest support
- intel/vsec: Panther Lake support
- p2sb: Do not hide the device if BIOS left it unhidden
- touchscreen_dmi: Add SARY Tab 3 tablet information
* tag 'platform-drivers-x86-v6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/intel/vsec: Add support for Panther Lake
platform/x86/intel/ifs: Add Clearwater Forest to CPU support list
platform/x86: touchscreen_dmi: Add info for SARY Tab 3 tablet
p2sb: Do not scan and remove the P2SB device when it is unhidden
p2sb: Move P2SB hide and unhide code to p2sb_scan_and_cache()
p2sb: Introduce the global flag p2sb_hidden_by_bios
p2sb: Factor out p2sb_read_from_cache()
alienware-wmi: Adds support to Alienware m16 R1 AMD
alienware-wmi: Fix X Series and G Series quirks
|
|
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
The DMI match information for these models has changed so the match
entries need updates.
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc3
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FE910C04 rmnet compositions
USB: serial: option: add MediaTek T7XX compositions
USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
USB: serial: option: add MeiG Smart SLM770A
USB: serial: option: add TCL IK512 MBIM & ECM
|
|
Both the ALC5645 and ALC5650 datasheets specify a recommended voltage of
1.8V for CPVDD, not 3.5V.
Fix the comment.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Fixes: 26aa19174f0d ("ASoC: dt-bindings: rt5645: add suppliers")
Fixes: 83d43ab0a1cb ("ASoC: dt-bindings: realtek,rt5645: Convert to dtschema")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241211035403.4157760-1-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the DMI match for a Lenovo laptop to the new DMI identifier.
This laptop ships with a different DMI identifier to what was expected,
and now has two identifiers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: ea657f6b24e1 ("ASoC: Intel: sof_sdw: Add quirk for cs42l43 system using host DMICs")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241216140821.153670-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Update the DMI match for a Lenovo laptop to the new DMI identifier.
This laptop ships with a different DMI identifier to what was expected,
and now has two identifiers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 83c062ae81e8 ("ASoC: Intel: sof_sdw: Add quirks for some new Lenovo laptops")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241216140821.153670-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Driver currently populates subsystem_device id in the
"hw_ver" field of ib_attr structure in query_device.
Updated to populate PCI revision ID.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Preethi G <preethi.gurusiddalingeswaraswamy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-6-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Current driver implementation doesn't populate the port_num
field in query_qp. Adding the code to convert internal firmware
port id to ibv defined port number and export it.
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-5-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Firmware expects "min_rnr_timer" as a mandatory attribute in
MODIFY_QP command during the RTR-RTS transition. This needs
to be enforced by the driver which is missing while setting
bnxt_set_mandatory_attributes that sends these flags as part
of modify_qp optimization.
Fixes: 82c32d219272 ("RDMA/bnxt_re: Add support for optimized modify QP")
Reviewed-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-4-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When RDMA app configures path MTU, add a check in modify_qp verb
to make sure that it doesn't go beyond interface MTU. If this
check fails, driver will fail the modify_qp verb.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-3-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The check for 9060 condition should only be made for legacy chips.
Fixes: 9152e0b722b2 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/20241211083931.968831-2-kalesh-anakkur.purayil@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
For many use cases (e.g. container images are just fetched from remote),
performance will be impacted if underlay page cache is up-to-date but
direct i/o flushes dirty pages first.
Instead, let's use buffered I/O by default to keep in sync with loop
devices and add a (re)mount option to explicitly give a try to use
direct I/O if supported by the underlying files.
The container startup time is improved as below:
[workload] docker.io/library/workpress:latest
unpack 1st run non-1st runs
EROFS snapshotter buffered I/O file 4.586404265s 0.308s 0.198s
EROFS snapshotter direct I/O file 4.581742849s 2.238s 0.222s
EROFS snapshotter loop 4.596023152s 0.346s 0.201s
Overlayfs snapshotter 5.382851037s 0.206s 0.214s
Fixes: fb176750266a ("erofs: add file-backed mount support")
Cc: Derek McGowan <derek@mcg.dev>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20241212134336.2059899-1-hsiangkao@linux.alibaba.com
|
|
Record `m_sb` and `m_dif` to replace `m_fscache`, `m_daxdev`, `m_fp`
and `m_dax_part_off` in order to simplify the codebase.
Note that `m_bdev` is still left since it can be assigned from
`sb->s_bdev` directly.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20241212235401.2857246-1-hsiangkao@linux.alibaba.com
|
|
Instead of just listing each one directly in `struct erofs_sb_info`
except that we still use `sb->s_bdev` for the primary block device.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20241216125310.930933-2-hsiangkao@linux.alibaba.com
|
|
Add condition check to register ACP PDM sound card by reading
_WOV acpi entry.
Fixes: 0386d765f27a ("ASoC: amd: ps: refactor acp device configuration read logic")
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20241213061147.1060451-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Alexandre observed a warning emitted from pci_msi_setup_msi_irqs() on a
RISCV platform which does not provide PCI/MSI support:
WARNING: CPU: 1 PID: 1 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x2c/0x32
__pci_enable_msix_range+0x30c/0x596
pci_msi_setup_msi_irqs+0x2c/0x32
pci_alloc_irq_vectors_affinity+0xb8/0xe2
RISCV uses hierarchical interrupt domains and correctly does not implement
the legacy fallback. The warning triggers from the legacy fallback stub.
That warning is bogus as the PCI/MSI layer knows whether a PCI/MSI parent
domain is associated with the device or not. There is a check for MSI-X,
which has a legacy assumption. But that legacy fallback assumption is only
valid when legacy support is enabled, but otherwise the check should simply
return -ENOTSUPP.
Loongarch tripped over the same problem and blindly enabled legacy support
without implementing the legacy fallbacks. There are weak implementations
which return an error, so the problem was papered over.
Correct pci_msi_domain_supports() to evaluate the legacy mode and add
the missing supported check into the MSI enable path to complete it.
Fixes: d2a463b29741 ("PCI/MSI: Reject multi-MSI early")
Reported-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/87ed2a8ow5.ffs@tglx
|
|
When USB-C monitor is connected directly to Intel Barlow Ridge host, it
goes into "redrive" mode that basically routes the DisplayPort signals
directly from the GPU to the USB-C monitor without any tunneling needed.
However, the host router must be powered on for this to work. Aaron
reported that there are a couple of cases where this will not work with
the current code:
- Booting with USB-C monitor plugged in.
- Plugging in USB-C monitor when the host router is in sleep state
(runtime suspended).
- Plugging in USB-C device while the system is in system sleep state.
In all these cases once the host router is runtime suspended the picture
on the connected USB-C display disappears too. This is certainly not
what the user expected.
For this reason improve the redrive mode handling to keep the host
router from runtime suspending when detect that any of the above cases
is happening.
Fixes: a75e0684efe5 ("thunderbolt: Keep the domain powered when USB4 port is in redrive mode")
Reported-by: Aaron Rainbolt <arainbolt@kfocus.org>
Closes: https://lore.kernel.org/linux-usb/20241009220118.70bfedd0@kf-ir16/
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If client send parallel smb2 negotiate request on same connection,
ksmbd_conn can be racy. smb2 negotiate handling that are not
performance-related can be serialized with conn lock.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
