summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-03-08dsa/mv88e6060: support nonzero mii base addressPeter Korsgaard
The mv88e6060 uses either the lower 16 or upper 16 mii addresses, depending on the value of the EE_CLK/ADDR4 pin. Support both configurations by using the sw_addr setting as base address. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-08r6040: bump to version 0.27 and date 23Feb2011Florian Fainelli
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-08r6040: fix multicast operationsShawn Lin
The original code does not work well when the number of mulitcast address to handle is greater than MCAST_MAX. It only enable promiscous mode instead of multicast hash table mode, so the hash table function will not be activated and all multicast frames will be recieved in this condition. This patch fixes the following issues with the r6040 NIC operating in multicast: 1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC hash table registers to make it process multicast traffic. 2) When the number of multicast address to handle is smaller than MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}. 3) The hashing of the address was not correct, due to an invalid substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an incorrect crc algorithm (ether_crc_le) instead of (ether_crc). 4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast hash table function. Reported-by: Marc Leclerc <marc-leclerc@signaturealpha.com> Tested-by: Marc Leclerc <marc-leclerc@signaturealpha.com> Signed-off-by: Shawn Lin <shawn@dmp.com.tw> Signed-off-by: Albert Chen <albert.chen@rdc.com.tw> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-08mmc: fix CONFIG_MMC_UNSAFE_RESUME regressionOhad Ben-Cohen
30201e7f3 ("mmc: skip detection of nonremovable cards on rescan") allowed skipping detection of nonremovable cards on mmc_rescan(). The intention was to only skip detection of hardwired cards that cannot be removed, so make sure this is indeed the case by directly checking for (lack of) MMC_CAP_NONREMOVABLE, instead of using mmc_card_is_removable(), which is overloaded with CONFIG_MMC_UNSAFE_RESUME semantics. The user-visible symptom of the bug this patch fixes is that no "mmc: card XXXX removed" message appears in dmesg when a card is removed and CONFIG_MMC_UNSAFE_RESUME=y. Reported-and-tested-by: Dmitry Shmidt <dimitrysh@google.com> Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-08Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next-2.6
2011-03-08rds: prevent BUG_ON triggering on congestion map updatesNeil Horman
Recently had this bug halt reported to me: kernel BUG at net/rds/send.c:329! Oops: Exception in kernel mode, sig: 5 [#1] SMP NR_CPUS=1024 NUMA pSeries Modules linked in: rds sunrpc ipv6 dm_mirror dm_region_hash dm_log ibmveth sg ext4 jbd2 mbcache sd_mod crc_t10dif ibmvscsic scsi_transport_srp scsi_tgt dm_mod [last unloaded: scsi_wait_scan] NIP: d000000003ca68f4 LR: d000000003ca67fc CTR: d000000003ca8770 REGS: c000000175cab980 TRAP: 0700 Not tainted (2.6.32-118.el6.ppc64) MSR: 8000000000029032 <EE,ME,CE,IR,DR> CR: 44000022 XER: 00000000 TASK = c00000017586ec90[1896] 'krdsd' THREAD: c000000175ca8000 CPU: 0 GPR00: 0000000000000150 c000000175cabc00 d000000003cb7340 0000000000002030 GPR04: ffffffffffffffff 0000000000000030 0000000000000000 0000000000000030 GPR08: 0000000000000001 0000000000000001 c0000001756b1e30 0000000000010000 GPR12: d000000003caac90 c000000000fa2500 c0000001742b2858 c0000001742b2a00 GPR16: c0000001742b2a08 c0000001742b2820 0000000000000001 0000000000000001 GPR20: 0000000000000040 c0000001742b2814 c000000175cabc70 0800000000000000 GPR24: 0000000000000004 0200000000000000 0000000000000000 c0000001742b2860 GPR28: 0000000000000000 c0000001756b1c80 d000000003cb68e8 c0000001742b27b8 NIP [d000000003ca68f4] .rds_send_xmit+0x4c4/0x8a0 [rds] LR [d000000003ca67fc] .rds_send_xmit+0x3cc/0x8a0 [rds] Call Trace: [c000000175cabc00] [d000000003ca67fc] .rds_send_xmit+0x3cc/0x8a0 [rds] (unreliable) [c000000175cabd30] [d000000003ca7e64] .rds_send_worker+0x54/0x100 [rds] [c000000175cabdb0] [c0000000000b475c] .worker_thread+0x1dc/0x3c0 [c000000175cabed0] [c0000000000baa9c] .kthread+0xbc/0xd0 [c000000175cabf90] [c000000000032114] .kernel_thread+0x54/0x70 Instruction dump: 4bfffd50 60000000 60000000 39080001 935f004c f91f0040 41820024 813d017c 7d094a78 7d290074 7929d182 394a0020 <0b090000> 40e2ff68 4bffffa4 39200000 Kernel panic - not syncing: Fatal exception Call Trace: [c000000175cab560] [c000000000012e04] .show_stack+0x74/0x1c0 (unreliable) [c000000175cab610] [c0000000005a365c] .panic+0x80/0x1b4 [c000000175cab6a0] [c00000000002fbcc] .die+0x21c/0x2a0 [c000000175cab750] [c000000000030000] ._exception+0x110/0x220 [c000000175cab910] [c000000000004b9c] program_check_common+0x11c/0x180 Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-08Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/jkirsher/net-next-2.6
2011-03-08ipv4: Fix scope value used in route src-address caching.David S. Miller
We have to use cfg->fc_scope not the final nh_scope value. Reported-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-08unfuck proc_sysctl ->d_compare()Al Viro
a) struct inode is not going to be freed under ->d_compare(); however, the thing PROC_I(inode)->sysctl points to just might. Fortunately, it's enough to make freeing that sucker delayed, provided that we don't step on its ->unregistering, clear the pointer to it in PROC_I(inode) before dropping the reference and check if it's NULL in ->d_compare(). b) I'm not sure that we *can* walk into NULL inode here (we recheck dentry->seq between verifying that it's still hashed / fetching dentry->d_inode and passing it to ->d_compare() and there's no negative hashed dentries in /proc/sys/*), but if we can walk into that, we really should not have ->d_compare() return 0 on it! Said that, I really suspect that this check can be simply killed. Nick? Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2011-03-07Linux 2.6.38-rc8v2.6.38-rc8Linus Torvalds
2011-03-07ipv4: Cache source address in nexthop entries.David S. Miller
When doing output route lookups, we have to select the source address if the user has not specified an explicit one. First, if the route has an explicit preferred source address specified, then we use that. Otherwise we search the route's outgoing interface for a suitable address. This search can be precomputed and cached at route insertion time. The only missing part is that we have to refresh this precomputed value any time addresses are added or removed from the interface, and this is accomplished by fib_update_nh_saddrs(). Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07Merge branch 's5p-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung * 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410 ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410 ARM: S3C64XX: Reduce output of s3c64xx_dma_init1() ARM: S3C64XX: Tone down SDHCI debugging ARM: S3C64XX: Add clock for i2c1 ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices ARM: S3C64XX: Fix keypad setup to configure correct number of rows ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02 ARM: S5P64X0: Fix number of GPIO lines in Bank F ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
2011-03-07Merge branch 'fixes' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: davinci: cpufreq: fix section mismatch warning DaVinci: fix compilation warnings in <mach/clkdev.h> davinci: tnetv107x: fix register indexing for GPIOs numbers > 31 davinci: da8xx/omap-l1x: add platform device for davinci-pcm-audio ARM: pxa/tosa: register wm9712 codec device ARM: pxa: enable pxa-pcm-audio on pxa210/pxa25x platform ARM: pxa/colibri: don't register pxa2xx-pcmcia nodes on non-colibri platforms ARM: pxa/tosa: drop setting LED trigger name, as it's unsupported now ARM: 6762/1: Update number of VIC for S5P6442 and S5PC100 ARM: 6761/1: Update number of VIC for S5PV210 ARM: 6768/1: hw_breakpoint: ensure debug logic is powered up on v7 cores ARM: 6767/1: ptrace: fix register indexing in GETHBPREGS request ARM: 6765/1: remove obsolete comment from asm/mach/arch.h ARM: 6757/1: fix tlb.h induced linux/swap.h build failure
2011-03-07Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: mmc: sdio: Allow sdio operations in other threads during sdio_add_func()
2011-03-07Merge branch 'drm-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6 * 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm: index i shadowed in 2nd loop drm/nv50-nvc0: prevent multiple vm/bar flushes occuring simultanenously drm/nouveau: fix regression causing ttm to not be able to evict vram drm/i915: Rebind the buffer if its alignment constraints changes with tiling drm/i915: Disable GPU semaphores by default drm/i915: Do not overflow the MMADDR write FIFO Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
2011-03-07ixgbe: fix setting and reporting of advertised speedsEmil Tantilov
Add the ability to set 100/F on x540. Fix reporting of advertised modes by adding check for phy.autoneg_advertised Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: fix spelling errorsEmil Tantilov
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: improve logic in ixgbe_init_mbx_params_pfEmil Tantilov
Use if/then instead of an all-inclusive case statement. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: add function descriptionEmil Tantilov
Add description for ixgbe_init_eeprom_params_X540 and whitespace fix. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: Enable flow control pause parameter auto-negotiation supportEmil Tantilov
This patch enables flow control pause parameters auto-negotiation support to 82599 based 10G Base-T, backplane devices and multi-speed fiber optics modules at 1G speed Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: Add x540 statistic counter definitionsEmil Tantilov
Add defines to accumulate and display x540 PHY statistic counters on transmit/receive. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: clear correct counters for flow control on 82599Emil Tantilov
The 82599 was not correctly having some of it's counters cleared for flow control. This change corrects that. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: cleanup PHY initEmil Tantilov
This change cleans up several situations in which we were either stepping over possible errors, or calling initialization routines multiple times. Also includes whitespace fixes where applicable. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: add support to FCoE DDP in target modeYi Zou
Add support to the ndo_fcoe_ddp_target() to allow the Intel 82599 device to also provide DDP offload capability when the upper FCoE protocol stack is operating as a target. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07vlan: add support to ndo_fcoe_ddp_target()Yi Zou
Add the new target ddp offload support ndo_fcoe_ddp_target(). Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07net: add ndo_fcoe_ddp_target() to support FCoE DDP in target modeYi Zou
The Fiber Channel over Ethernet (FCoE) Direct Data Placement (DDP) can also be used for FCoE target, where the DDP used for read I/O on an initiator can be used on an FCoE target to speed up the write I/O to the target from the initiator. The added ndo_fcoe_ddp_target() works in the similar way as the existing ndo_fcoe_ddp_setup() to allow the underlying hardware set up the DDP context accordingly when it gets called from the FCoE target implementation on top the existing Open-FCoE fcoe/libfc protocol stack so without losing the ability to provide DDP for read I/O as an initiator, it can also provide DDP offload to the write I/O coming from the initiator as a target. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07ixgbe: fix missing function pointer conversionDon Skidmore
In the previous commit: commit 5e655105e3e19d746f9e95c514b014c11c3d1b6a Author: Don Skidmore <donald.c.skidmore@intel.com> Date: Fri Feb 25 01:58:04 2011 +0000 ixgbe: add function pointer for semaphore function there was one release of the semaphore function call which did not get converted to a function pointer. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07igb: Add stats output for OS2BMC feature on i350 devicesCarolyn Wyborny
This patch adds statistics output for OS2BMC feature which is configured by eeprom on capable devices. Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07e1000e: fix build issue due to undefined reference to crc32_leEmil Tantilov
kernel build fails with: drivers/built-in.o: In function `e1000_lv_jumbo_workaround_ich8lan': (.text+0x3e7a8): undefined reference to `crc32_le' when CONFIG_CRC32 is not set or does not match the CONFIG_E1000E selection. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-03-07bonding 802.3ad: Rename rx_machine_lock to state_machine_lockNils Carlson
Rename the rx_machine_lock to state_machine_lock as this makes more sense in light of it now protecting all the state machines against concurrency. Signed-off-by: Nils Carlson <nils.carlson@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07bonding 802.3ad: Fix the state machine locking v2Nils Carlson
Changes since v1: * Clarify an unclear comment * Move a (possible) name change to a separate patch The ad_rx_machine, ad_periodic_machine and ad_port_selection_logic functions all inspect and alter common fields within the port structure. Previous to this patch, only the ad_rx_machines were mutexed, and the periodic and port_selection could run unmutexed against an ad_rx_machine trigged by an arriving LACPDU. This patch remedies the situation by protecting all the state machines from concurrency. This is accomplished by locking around all the state machines for a given port, which are executed at regular intervals; and the ad_rx_machine when handling an incoming LACPDU. Signed-off-by: Nils Carlson <nils.carlson@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07drivers/net/macvtap: fix error checkNicolas Kaiser
'len' is unsigned of type size_t and can't be negative. Signed-off-by: Nicolas Kaiser <nikai@nikai.net> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07af_unix: remove unused struct sockaddr_un cruftHagen Paul Pfeifer
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07sctp: several declared/set but unused fixesHagen Paul Pfeifer
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07af_packet: struct socket declared/assigned but unusedHagen Paul Pfeifer
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07mcast: net_device dev not usedHagen Paul Pfeifer
ip6_mc_source(), ip6_mc_msfilter() as well as ip6_mc_msfget() declare and assign dev but do not use the variable afterwards. Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07s2io: fix uninitialized compile warningShan Wei
drivers/net/s2io.c:7559: warning: ‘tcp_len’ may be used uninitialized in this function Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07bonding: COW before overwriting the destination MAC addressChangli Gao
When there is a ptype handler holding a clone of this skb, whose destination MAC addresse is overwritten, the owner of this handler may get a corrupted packet. Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07bonding: remove the unused dummy functions when net poll controller isn't ↵Changli Gao
enabled These two functions are only used when net poll controller is enabled. Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07Merge branch 'davem-next.r8169' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6
2011-03-07net: allow handlers to be processed for orig_devJiri Pirko
This was there before, I forgot about this. Allows deliveries to ptype_base handlers registered for orig_dev. I presume this is still desired. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07net: fix multithreaded signal handling in unix recv routinesRainer Weikusat
The unix_dgram_recvmsg and unix_stream_recvmsg routines in net/af_unix.c utilize mutex_lock(&u->readlock) calls in order to serialize read operations of multiple threads on a single socket. This implies that, if all n threads of a process block in an AF_UNIX recv call trying to read data from the same socket, one of these threads will be sleeping in state TASK_INTERRUPTIBLE and all others in state TASK_UNINTERRUPTIBLE. Provided that a particular signal is supposed to be handled by a signal handler defined by the process and that none of this threads is blocking the signal, the complete_signal routine in kernel/signal.c will select the 'first' such thread it happens to encounter when deciding which thread to notify that a signal is supposed to be handled and if this is one of the TASK_UNINTERRUPTIBLE threads, the signal won't be handled until the one thread not blocking on the u->readlock mutex is woken up because some data to process has arrived (if this ever happens). The included patch fixes this by changing mutex_lock to mutex_lock_interruptible and handling possible error returns in the same way interruptions are handled by the actual receive-code. Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Add multicast filter capability for LancerPadmanabh Ratnakar
Lancer requires multicast capability flag set during IFACE_CREATE for adding multicast filters. Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Disarm CQ and EQ to disable interrupt in LancerPadmanabh Ratnakar
For Lancer disable interrupts in close by disarming CQs and EQs. Change the order of calls in be_close to achieve the correct result. Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Remove TX Queue stop in closePadmanabh Ratnakar
Remove TX Queue stop in close Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Change f/w command versions for LancerPadmanabh Ratnakar
Change f/w command versions for Lancer Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Add error recovery during load for LancerPadmanabh Ratnakar
Add error recovery during load for Lancer Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Checksum field valid only for TCP/UDPPadmanabh Ratnakar
L4 checksum field is valid only for TCP/UDP packets in Lancer Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07be2net: Remove ERR compl workaround for LancerPadmanabh Ratnakar
Workaround added for Lancer in handling RX ERR completion received when no RX buffers are posted is not needed. Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-03-07ipv4: Inline fib_semantic_match into check_leafDavid S. Miller
This elimiates a lot of pure overhead due to parameter passing. Signed-off-by: David S. Miller <davem@davemloft.net>