summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-01-17wifi: ath11k: add channel 177 into 5 GHz channel listWen Gong
Add support for the 5 GHz channel 177 with center frequency 5885 MHz and operating class 125 per IEEE Std 802.11ax-2021, Table E-4. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221220101912.30816-1-quic_wgong@quicinc.com
2023-01-17wifi: ath11k: Add support to configure FTM responder roleSowmiya Sree Elavalagan
Fine Timing Measurement(FTM) support is used to measure round trip time between two nodes. Enable FTM responder feature using hw_params on supported device. Since FTM functionality is offloaded to firmware, adding the interface allows user space to enable or disable FTM responder. Also add support for advertising the same in extended capabilities. QCA6390, WCN6855 and WCN6750 do not support this feature. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221220044435.10506-1-quic_rajkbhag@quicinc.com
2023-01-17wifi: ath9k: Fix potential stack-out-of-bounds write in ath9k_wmi_rsp_callback()Minsuk Kang
Fix a stack-out-of-bounds write that occurs in a WMI response callback function that is called after a timeout occurs in ath9k_wmi_cmd(). The callback writes to wmi->cmd_rsp_buf, a stack-allocated buffer that could no longer be valid when a timeout occurs. Set wmi->last_seq_id to 0 when a timeout occurred. Found by a modified version of syzkaller. BUG: KASAN: stack-out-of-bounds in ath9k_wmi_ctrl_rx Write of size 4 Call Trace: memcpy ath9k_wmi_ctrl_rx ath9k_htc_rx_msg ath9k_hif_usb_reg_in_cb __usb_hcd_giveback_urb usb_hcd_giveback_urb dummy_timer call_timer_fn run_timer_softirq __do_softirq irq_exit_rcu sysvec_apic_timer_interrupt Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230104124130.10996-1-linuxlovemin@yonsei.ac.kr
2023-01-17wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() failsFedor Pchelkin
Syzkaller detected a memory leak of skbs in ath9k_hif_usb_rx_stream(). While processing skbs in ath9k_hif_usb_rx_stream(), the already allocated skbs in skb_pool are not freed if ath9k_hif_usb_rx_stream() fails. If we have an incorrect pkt_len or pkt_tag, the input skb is considered invalid and dropped. All the associated packets already in skb_pool should be dropped and freed. Added a comment describing this issue. The patch also makes remain_skb NULL after being processed so that it cannot be referenced after potential free. The initialization of hif_dev fields which are associated with remain_skb (rx_remain_len, rx_transfer_len and rx_pad_len) is moved after a new remain_skb is allocated. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: 6ce708f54cc8 ("ath9k: Fix out-of-bound memcpy in ath9k_hif_usb_rx_stream") Fixes: 44b23b488d44 ("ath9k: hif_usb: Reduce indent 1 column") Reported-by: syzbot+e9632e3eb038d93d6bc6@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230104123615.51511-1-pchelkin@ispras.ru
2023-01-17wifi: ath9k: htc_hst: free skb in ath9k_htc_rx_msg() if there is no callback ↵Fedor Pchelkin
function It is stated that ath9k_htc_rx_msg() either frees the provided skb or passes its management to another callback function. However, the skb is not freed in case there is no another callback function, and Syzkaller was able to cause a memory leak. Also minor comment fix. Found by Linux Verification Center (linuxtesting.org) with Syzkaller. Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+e008dccab31bd3647609@syzkaller.appspotmail.com Reported-by: syzbot+6692c72009680f7c4eb2@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230104123546.51427-1-pchelkin@ispras.ru
2023-01-10wifi: ath11k: debugfs: fix to work with multiple PCI devicesKalle Valo
ath11k fails to load if there are multiple ath11k PCI devices with same name: ath11k_pci 0000:01:00.0: Hardware name qcn9074 hw1.0 debugfs: Directory 'ath11k' with parent '/' already present! ath11k_pci 0000:01:00.0: failed to create ath11k debugfs ath11k_pci 0000:01:00.0: failed to create soc core: -17 ath11k_pci 0000:01:00.0: failed to init core: -17 ath11k_pci: probe of 0000:01:00.0 failed with error -17 Fix this by creating a directory for each ath11k device using schema <bus>-<devname>, for example "pci-0000:06:00.0". This directory created under the top-level ath11k directory, for example /sys/kernel/debug/ath11k. The reference to the toplevel ath11k directory is not stored anymore within ath11k, instead it's retrieved using debugfs_lookup(). If the directory does not exist it will be created. After the last directory from the ath11k directory is removed, for example when doing rmmod ath11k, the empty ath11k directory is left in place, it's a minor cosmetic issue anyway. Here's an example hierarchy with one WCN6855: ath11k `-- pci-0000:06:00.0 |-- mac0 | |-- dfs_block_radar_events | |-- dfs_simulate_radar | |-- ext_rx_stats | |-- ext_tx_stats | |-- fw_dbglog_config | |-- fw_stats | | |-- beacon_stats | | |-- pdev_stats | | `-- vdev_stats | |-- htt_stats | |-- htt_stats_reset | |-- htt_stats_type | `-- pktlog_filter |-- simulate_fw_crash `-- soc_dp_stats I didn't have a test setup where I could connect multiple ath11k devices to the same the host, so I have only tested this with one device. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1 Tested-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221220121231.20120-1-kvalo@kernel.org
2022-12-22wifi: ath9k: remove most hidden macro dependencies on ahWenli Looi
Adds an explicit _ah parameter to most macros that previously had a hidden dependency on ah. This makes the code more compliant with the style guide. This change does not appear to affect the final binary. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/c8369317-cf84-f0e3-fe8-9b6e22e43a6a@ucalgary.ca
2022-12-08wifi: ath11k: fix monitor mode bringup crashNagarajan Maran
When the interface is brought up in monitor mode, it leads to NULL pointer dereference crash. This crash happens when the packet type is extracted for a SKB. This extraction which is present in the received msdu delivery path,is not needed for the monitor ring packets since they are all RAW packets. Hence appending the flags with "RX_FLAG_ONLY_MONITOR" to skip that extraction. Observed calltrace: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000064 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000 [0000000000000064] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP Modules linked in: ath11k_pci ath11k qmi_helpers CPU: 2 PID: 1781 Comm: napi/-271 Not tainted 6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6 Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k] lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k] sp : ffff80000ef5bb10 x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0 x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000 x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600 x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006 x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143 x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8 x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052 Call trace: ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k] ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k] ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k] ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k] ath11k_dp_service_srng+0x234/0x338 [ath11k] ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k] __napi_poll+0x5c/0x190 napi_threaded_poll+0xf0/0x118 kthread+0xf4/0x110 ret_from_fork+0x10/0x20 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Reported-by: Florian Schmidt <florian@fls.name> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216573 Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221129142532.23421-1-quic_nmaran@quicinc.com
2022-12-08wifi: ath11k: Fix scan request param frame size warningKarthikeyan Kathirvel
Following warning was observed drivers/net/wireless/ath/ath11k/mac.c:2351:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=] A local variable is declared with a size larger than 1024 bytes this causing a compilation warning. Change the local variable to heap memory to fix the warning. Tested-on: IPQ8074 AHB WLAN.HK.2.7.0.1-01701-QCAHKSWPL_SILICONZ-1 v2 Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221205192125.13533-1-quic_kathirve@quicinc.com
2022-12-08wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()Minsuk Kang
This patch fixes a use-after-free in ath9k that occurs in ath9k_hif_usb_disconnect() when ath9k_destroy_wmi() is trying to access 'drv_priv' that has already been freed by ieee80211_free_hw(), called by ath9k_htc_hw_deinit(). The patch moves ath9k_destroy_wmi() before ieee80211_free_hw(). Note that urbs from the driver should be killed before freeing 'wmi' with ath9k_destroy_wmi() as their callbacks will access 'wmi'. Found by a modified version of syzkaller. ================================================================== BUG: KASAN: use-after-free in ath9k_destroy_wmi+0x38/0x40 Read of size 8 at addr ffff8881069132a0 by task kworker/0:1/7 CPU: 0 PID: 7 Comm: kworker/0:1 Tainted: G O 5.14.0+ #131 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Workqueue: usb_hub_wq hub_event Call Trace: dump_stack_lvl+0x8e/0xd1 print_address_description.constprop.0.cold+0x93/0x334 ? ath9k_destroy_wmi+0x38/0x40 ? ath9k_destroy_wmi+0x38/0x40 kasan_report.cold+0x83/0xdf ? ath9k_destroy_wmi+0x38/0x40 ath9k_destroy_wmi+0x38/0x40 ath9k_hif_usb_disconnect+0x329/0x3f0 ? ath9k_hif_usb_suspend+0x120/0x120 ? usb_disable_interface+0xfc/0x180 usb_unbind_interface+0x19b/0x7e0 ? usb_autoresume_device+0x50/0x50 device_release_driver_internal+0x44d/0x520 bus_remove_device+0x2e5/0x5a0 device_del+0x5b2/0xe30 ? __device_link_del+0x370/0x370 ? usb_remove_ep_devs+0x43/0x80 ? remove_intf_ep_devs+0x112/0x1a0 usb_disable_device+0x1e3/0x5a0 usb_disconnect+0x267/0x870 hub_event+0x168d/0x3950 ? rcu_read_lock_sched_held+0xa1/0xd0 ? hub_port_debounce+0x2e0/0x2e0 ? check_irq_usage+0x860/0xf20 ? drain_workqueue+0x281/0x360 ? lock_release+0x640/0x640 ? rcu_read_lock_sched_held+0xa1/0xd0 ? rcu_read_lock_bh_held+0xb0/0xb0 ? lockdep_hardirqs_on_prepare+0x273/0x3e0 process_one_work+0x92b/0x1460 ? pwq_dec_nr_in_flight+0x330/0x330 ? rwlock_bug.part.0+0x90/0x90 worker_thread+0x95/0xe00 ? __kthread_parkme+0x115/0x1e0 ? process_one_work+0x1460/0x1460 kthread+0x3a1/0x480 ? set_kthread_struct+0x120/0x120 ret_from_fork+0x1f/0x30 The buggy address belongs to the page: page:ffffea00041a44c0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x106913 flags: 0x200000000000000(node=0|zone=2) raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as freed page last allocated via order 3, migratetype Unmovable, gfp_mask 0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), pid 7, ts 38347963444, free_ts 41399957635 prep_new_page+0x1aa/0x240 get_page_from_freelist+0x159a/0x27c0 __alloc_pages+0x2da/0x6a0 alloc_pages+0xec/0x1e0 kmalloc_order+0x39/0xf0 kmalloc_order_trace+0x19/0x120 __kmalloc+0x308/0x390 wiphy_new_nm+0x6f5/0x1dd0 ieee80211_alloc_hw_nm+0x36d/0x2230 ath9k_htc_probe_device+0x9d/0x1e10 ath9k_htc_hw_init+0x34/0x50 ath9k_hif_usb_firmware_cb+0x25f/0x4e0 request_firmware_work_func+0x131/0x240 process_one_work+0x92b/0x1460 worker_thread+0x95/0xe00 kthread+0x3a1/0x480 page last free stack trace: free_pcp_prepare+0x3d3/0x7f0 free_unref_page+0x1e/0x3d0 device_release+0xa4/0x240 kobject_put+0x186/0x4c0 put_device+0x20/0x30 ath9k_htc_disconnect_device+0x1cf/0x2c0 ath9k_htc_hw_deinit+0x26/0x30 ath9k_hif_usb_disconnect+0x2d9/0x3f0 usb_unbind_interface+0x19b/0x7e0 device_release_driver_internal+0x44d/0x520 bus_remove_device+0x2e5/0x5a0 device_del+0x5b2/0xe30 usb_disable_device+0x1e3/0x5a0 usb_disconnect+0x267/0x870 hub_event+0x168d/0x3950 process_one_work+0x92b/0x1460 Memory state around the buggy address: ffff888106913180: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff888106913200: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff888106913280: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff888106913300: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff888106913380: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ================================================================== Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221205014308.1617597-1-linuxlovemin@yonsei.ac.kr
2022-12-07wifi: ath11k: add ipq5018 device supportSriram R
ipq5018 is a ahb 2ghz device, enable the compatible support for ipq5018 in ahb. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-9-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: add new hw ops for IPQ5018 to get rx dest ring hashmapSriram R
The Destination ring control register is different for IPQ5018 when compared to IPQ8074/IPQ6018/QCN9074. Hence create a new hw ops to fetch the hash ring map for different device variants. ipq5018 hw ops is similar to qcn9074 except for this change, so reuse all the qcn9074 ops for ipq5018. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-8-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: initialize hw_ops for IPQ5018Sriram R
The ipq5018_ops is initialized for IPQ5018. This is different from other platforms. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-7-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: update hal srng regs for IPQ5018Sriram R
IPQ5018 hal srng register address & offsets are not similar to IPQ8074/IPQ6018/QCN9074, hence define a new set of srng register group data for IPQ5018. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-6-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: remap ce register space for IPQ5018Sriram R
In IPQ5018 ce register space is moved out of wcss unlike ipq8074 or ipq6018 and the space is not contiguous, hence remap the CE registers to a new space to access them. Register read/write is modified to check if the register to be written falls in the CE register space and corresponding register is written. Also adjust the interrupt register address to ce irq enable/disable. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: update ce configurations for IPQ5018Sriram R
IPQ5018 is a single pdev device. Update host and target CE configurations accordingly. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-4-quic_kathirve@quicinc.com
2022-12-07wifi: ath11k: update hw params for IPQ5018Sriram R
Add new compatible string for IPQ5018 and add required hw params for IPQ5018. The hw descriptors size and datapath ops are similar to QCN9074, hence reuse the same. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-3-quic_kathirve@quicinc.com
2022-12-07dt: bindings: net: ath11k: add IPQ5018 compatibleSriram R
Add IPQ5018 device support for ath11k. Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221122132152.17771-2-quic_kathirve@quicinc.com
2022-12-02wifi: ath11k: Fix race condition with struct htt_ppdu_stats_infoGovindaraj Saminathan
A crash happens when running the traffic with multiple clients: Crash Signature : Unable to handle kernel paging request at virtual address ffffffd700970918 During the crash, PC points to "ieee80211_tx_rate_update+0x30/0x68 [mac80211]" LR points to "ath11k_dp_htt_htc_t2h_msg_handler+0x5a8/0x8a0 [ath11k]". Struct ppdu_stats_info is allocated and accessed from event callback via copy engine tasklet, this has a problem when freeing it from ath11k_mac_op_stop(). Use data_lock during entire ath11k_dp_htt_get_ppdu_desc() call to protect struct htt_ppdu_stats_info access and to avoid race condition when accessing it from ath11k_mac_op_stop(). Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Govindaraj Saminathan <quic_gsaminat@quicinc.com> Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221124071104.22506-1-quic_kathirve@quicinc.com
2022-11-29wifi: ath12k: driver for Qualcomm Wi-Fi 7 devicesKalle Valo
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP and station; WCN7850 supports only station mode. Monitor mode is not (yet) supported. Only PCI bus devices are supported. ath12k is forked from an earlier version of ath11k. It was simpler to have a "clean start" for the new generation and not try to share the code with ath11k. This makes maintenance easier and avoids major changes in ath11k, which would have significantly increased the risk of regressions in existing setups. ath12k uses le32 and cpu_to_le32() macros to handle endian conversions, instead of using the firmware byte swap feature utilized by ath11k. There is only one kernel module, named ath12k.ko. Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but work is ongoing to add EHT mode (IEEE 802.11be) support. The size of the driver is ~41 kLOC and 45 files. To make the review easier, this initial version of ath12k does not support Device Tree, debugfs or any other extra features. Those will be added later, after ath12k is accepted to upstream. The driver is build tested by Intel's kernel test robot with both GCC and Clang. Sparse reports no warnings. The driver is mostly free of checkpatch warnings, albeit few of the warnings are omitted on purpose, list of them here: https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52 The driver has had multiple authors who are listed in alphabetical order below. Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com> Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com> Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com> Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com> Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com> Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Co-developed-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com> Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com> Co-developed-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
2022-11-28Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo
ath.git patches for v6.2. Major changes: ath10k * store WLAN firmware version in SMEM image table
2022-11-28wifi: rtw88: fix race condition when doing H2C commandJi-Pin Jou
For SDIO/USB interface, since the tranferring speed is slower than that in PCIE, it may have race condition when the driver sets down H2C command to the FW. In the function rtw_fw_send_h2c_command, before the patch, box_reg is written first, then box_ex_reg is written. FW starts to work and fetch the value of box_ex_reg, when the most significant byte of box_reg(4 bytes) is written. Meanwhile, for SDIO/USB interface, since the transferring speed is slow, the driver is still in writing the new value of box_ex_reg through the bus, and FW may get the wrong value of box_ex_reg at the moment. To prevent the above driver/FW racing situation, box_ex_reg is written first then box_reg. Furthermore, it is written in 4 bytes at a time, instead of written in one byte one by one. It can increase the speed for SDIO/USB interface. Signed-off-by: Ji-Pin Jou <neo_jou@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221124064442.28042-1-pkshih@realtek.com
2022-11-28wifi: b43: remove reference to removed config B43_PCMCIALukas Bulwahn
Commit 399500da18f7 ("ssb: pick PCMCIA host code support from b43 driver") removes the config B43_PCMCIA. Clean up the last reference to this removed config B43_PCMCIA in the b43_print_driverinfo() function. Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221122131248.23738-1-lukas.bulwahn@gmail.com
2022-11-28wifi: rtl8xxxu: Fix use after rcu_read_unlock in rtl8xxxu_bss_info_changedBitterblue Smith
Commit a8b5aef2cca1 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width") introduced a line where the pointer returned by ieee80211_find_sta() is used after rcu_read_unlock(). Move rcu_read_unlock() a bit lower to fix this. Fixes: a8b5aef2cca1 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width") Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/3c82ad09-7593-3be1-1d2c-e58505fb43cb@gmail.com
2022-11-28wifi: plfxlc: fix potential memory leak in __lf_x_usb_enable_rx()Ziyang Xuan
urbs does not be freed in exception paths in __lf_x_usb_enable_rx(). That will trigger memory leak. To fix it, add kfree() for urbs within "error" label. Compile tested only. Fixes: 68d57a07bfe5 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221119051900.1192401-1-william.xuanziyang@huawei.com
2022-11-25wifi: carl9170: Replace zero-length array of trailing structs with flex-arrayKees Cook
Zero-length arrays are deprecated[1] and are being replaced with flexible array members in support of the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3. Replace zero-length array with flexible-array member. This results in no differences in binary output. [1] https://github.com/KSPP/linux/issues/78 Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221118211146.never.395-kees@kernel.org
2022-11-25wifi: ath10k: Store WLAN firmware version in SMEM image tableYoughandhar Chintala
In a SoC based solution, it would be useful to know the versions of the various binary firmware blobs the system is running on. On a QCOM based SoC, this info can be obtained from socinfo debugfs infrastructure. For this to work, respective subsystem drivers have to export the firmware version information to an SMEM based version information table. Having firmware version information at one place will help quickly figure out the firmware versions of various subsystems on the device instead of going through builds/logs in an event of a system crash. Fill WLAN firmware version information in SMEM version table to be printed as part of socinfo debugfs infrastructure on a Qualcomm based SoC. This change is applicable only for SNOC/QMI based targets. Example: cat /sys/kernel/debug/qcom_socinfo/cnss/name QC_IMAGE_VERSION_STRING=WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1 Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1 Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221117180534.2267-1-quic_youghand@quicinc.com
2022-11-22wifi: p54: Replace zero-length array of trailing structs with flex-arrayKees Cook
Zero-length arrays are deprecated[1] and are being replaced with flexible array members in support of the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3. Replace zero-length array with flexible-array member. This results in no differences in binary output (most especially because struct pda_antenna_gain is unused). The struct is kept for future reference. [1] https://github.com/KSPP/linux/issues/78 Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221118234240.gonna.369-kees@kernel.org
2022-11-22wifi: rtw89: fix physts IE page checkZong-Zhe Yang
The index RTW89_PHYSTS_BITMAP_NUM is not a valid physts IE page. So, fix the check condition. Fixes: eb4e52b3f38d ("rtw89: fix incorrect channel info during scan") Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221118042322.26794-1-pkshih@realtek.com
2022-11-22wifi: rtw89: avoid inaccessible IO operations during doing change_interface()Ping-Ke Shih
During doing change_interface(), hardware is power-off, so some components are inaccessible and return error. This causes things unexpected, and we don't have a warning message for that. So, ignore some IO operations in this situation, and add a warning message to indicate something wrong. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221117085235.53777-1-pkshih@realtek.com
2022-11-22wifi: rtw89: switch BANDEDGE and TX_SHAPE based on OFDMA trigger frameEric Huang
There are some registers for transmit waveform control, two of them used in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls whether to apply band edge filter to transmit waveform. TX_SHAPE controls whether to apply triangular mask to transmit waveform. It is found for some chip, these two should be turned off during OFDMA UL traffic for better performance. Signed-off-by: Eric Huang <echuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com
2022-11-22wifi: rtw89: read CFO from FD or preamble CFO field of phy status ie_type 1 ↵Eric Huang
accordingly Add macro to get FD(frequency domain) CFO field from ie_type 1, and correct the naming for preamble CFO field. Each IC could assign the CFO source to either FD CFO or preamble CFO in chip_info. Based on the suggestion from HW designer, rtw8852b and its derived versions will have better CFO tracking performance with FD CFO. Signed-off-by: Eric Huang <echuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221117063001.42967-2-pkshih@realtek.com
2022-11-22wifi: rtw89: 8852b: correct TX power controlled by BT-coexistencePing-Ke Shih
When coexistence mechanism is under free-run mode, it could adjust WiFi and BT TX power to avoid interference with each other. For other cases, it should keep original TX power from regular predefined tables, so set correct values to 255 for these cases. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221117061832.42057-1-pkshih@realtek.com
2022-11-22wifi: brcmfmac: Use struct_size() in code ralated to struct brcmf_dload_data_leGustavo A. R. Silva
Prefer struct_size() over open-coded versions of idiom: sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count where count is the max number of items the flexible array is supposed to contain. In this particular case, in the open-coded version sizeof(typeof-flex-array-elements) is implicit in _count_ because the type of the flex array data is u8: drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h:941: 941 struct brcmf_dload_data_le { 942 __le16 flag; 943 __le16 dload_type; 944 __le32 len; 945 __le32 crc; 946 u8 data[]; 947 }; Link: https://github.com/KSPP/linux/issues/160 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/41845ad3660ed4375f0c03fd36a67b2e12fafed5.1668548907.git.gustavoars@kernel.org
2022-11-22wifi: brcmfmac: replace one-element array with flexible-array member in ↵Gustavo A. R. Silva
struct brcmf_dload_data_le One-element arrays are deprecated, and we are replacing them with flexible array members instead. So, replace one-element array with flexible-array member in struct brcmf_dload_data_le. Important to mention is that doing a build before/after this patch results in no binary output differences. This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/230 Link: https://github.com/KSPP/linux/issues/79 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/905f5b68cf93c812360d081caae5b15221db09b6.1668548907.git.gustavoars@kernel.org
2022-11-22wifi: brcmfmac: Use struct_size() and array_size() in code ralated to struct ↵Gustavo A. R. Silva
brcmf_gscan_config Prefer struct_size() over open-coded versions of idiom: sizeof(struct-with-flex-array) + sizeof(typeof-flex-array-elements) * count where count is the max number of items the flexible array is supposed to contain. Also, use array_size() in call to memcpy(). Link: https://github.com/KSPP/linux/issues/160 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/de0226a549c8d000d8974e207ede786220a3df1a.1668466470.git.gustavoars@kernel.org
2022-11-22wifi: brcmfmac: Replace one-element array with flexible-array memberGustavo A. R. Silva
One-element arrays are deprecated, and we are replacing them with flexible array members instead. So, replace one-element array with flexible-array member in struct brcmf_gscan_config. Important to mention is that doing a build before/after this patch results in no binary output differences. This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/79 Link: https://github.com/KSPP/linux/issues/241 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/7694550aa9a2753a73a687f61af9441c8cf52fd7.1668466470.git.gustavoars@kernel.org
2022-11-18Merge tag 'rxrpc-next-20221116' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc: Fix oops and missing config conditionals The patches that were pulled into net-next previously[1] had some issues that this patchset fixes: (1) Fix missing IPV6 config conditionals. (2) Fix an oops caused by calling udpv6_sendmsg() directly on an AF_INET socket. (3) Fix the validation of network addresses on entry to socket functions so that we don't allow an AF_INET6 address if we've selected an AF_INET transport socket. Link: https://lore.kernel.org/r/166794587113.2389296.16484814996876530222.stgit@warthog.procyon.org.uk/ [1] ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18net: fix napi_disable() logic errorEric Dumazet
Dan reported a new warning after my recent patch: New smatch warnings: net/core/dev.c:6409 napi_disable() error: uninitialized symbol 'new'. Indeed, we must first wait for STATE_SCHED and STATE_NPSVC to be cleared, to make sure @new variable has been initialized properly. Fixes: 4ffa1d1c6842 ("net: adopt try_cmpxchg() in napi_{enable|disable}()") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18rxrpc: uninitialized variable in rxrpc_send_ack_packet()Dan Carpenter
The "pkt" was supposed to have been deleted in a previous patch. It leads to an uninitialized variable bug. Fixes: 72f0c6fb0579 ("rxrpc: Allocate ACK records at proposal and queue for transmission") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18rxrpc: fix rxkad_verify_response()Dan Carpenter
The error handling for if skb_copy_bits() fails was accidentally deleted so the rxkad_decrypt_ticket() function is not called. Fixes: 5d7edbc9231e ("rxrpc: Get rid of the Rx ring") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18net: ethernet: mtk_eth_soc: remove cpu_relax in mtk_pending_workLorenzo Bianconi
Get rid of cpu_relax in mtk_pending_work routine since MTK_RESETTING is set only in mtk_pending_work() and it runs holding rtnl lock Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18net: ethernet: mtk_eth_soc: do not overwrite mtu configuration running reset ↵Lorenzo Bianconi
routine Restore user configured MTU running mtk_hw_init() during tx timeout routine since it will be overwritten after a hw reset. Reported-by: Felix Fietkau <nbd@nbd.name> Fixes: 9ea4d311509f ("net: ethernet: mediatek: add the whole ethernet reset into the reset process") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18net: ipa: avoid a null pointer dereferenceAlex Elder
Dan Carpenter reported that Smatch found an instance where a pointer which had previously been assumed could be null (as indicated by a null check) was later dereferenced without a similar check. In practice this doesn't lead to a problem because currently the pointers used are all non-null. Nevertheless this patch addresses the reported problem. In addition, I spotted another bug that arose in the same commit. When the command to initialize a routing table memory region was added, the number of entries computed for the non-hashed table was wrong (it ended up being a Boolean rather than the count intended). This bug is fixed here as well. Reported-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/kernel-janitors/Y3OOP9dXK6oEydkf@kili Tested-by: Caleb Connolly <caleb.connolly@linaro.com> Fixes: 5cb76899fb47 ("net: ipa: reduce arguments to ipa_table_init_add()") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18Merge tag 'wireless-next-2022-11-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.2 Second set of patches for v6.2. Only driver patches this time, nothing really special. Unused platform data support was removed from wl1251 and rtw89 got WoWLAN support. Major changes: ath11k * support configuring channel dwell time during scan rtw89 * new dynamic header firmware format support * Wake-over-WLAN support rtl8xxxu * enable IEEE80211_HW_SUPPORT_FAST_XMIT ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18Merge branch 'sctp-vrf'David S. Miller
Xin Long says: ==================== sctp: support vrf processing This patchset adds the VRF processing in SCTP. Simliar to TCP/UDP, it includes socket bind and socket/association lookup changes. For socket bind change, it allows sockets to bind to a VRF device and allows multiple sockets with the same IP and PORT to bind to different interfaces in patch 1-3. For socket/association lookup change, it adds dif and sdif check in both asoc and ep lookup in patch 4 and 5, and when binding to nodev, users can decide if accept the packets received from one l3mdev by setup a sysctl option in patch 6. Note with VRF support, in a netns, an association will be decided by src ip + src port + dst ip + dst port + bound_dev_if, and it's possible for ss to have: State Local Address:Port Peer Address:Port ESTAB 192.168.1.2%vrf-s1:1234 `- ESTAB 192.168.1.2%veth1:1234 192.168.1.1:1234 ESTAB 192.168.1.2%vrf-s2:1234 `- ESTAB 192.168.1.2%veth2:1234 192.168.1.1:1234 See the selftest in patch 7 for more usage. Also, thanks Carlo for testing this patch series on their use. v1->v2: - In Patch 5, move sctp_sk_bound_dev_eq() definition to net/sctp/ input.c to avoid a build error when IP_SCTP is disabled, as Paolo suggested. - In Patch 7, avoid one sleep by disabling the IPv6 dad, and remove another sleep by using ss to check if the server's ready, and also delete two unncessary sleeps in sctp_hello.c, as Paolo suggested. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18selftests: add a selftest for sctp vrfXin Long
This patch adds 12 small test cases: 01-04 test for the sysctl net.sctp.l3mdev_accept. 05-10 test for only binding to a right l3mdev device, the connection can be created. 11-12 test for two socks binding to different l3mdev devices at the same time, each of them can process the packets from the corresponding peer. The tests run for both IPv4 and IPv6 SCTP. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18sctp: add sysctl net.sctp.l3mdev_acceptXin Long
This patch is to add sysctl net.sctp.l3mdev_accept to allow users to change the pernet global l3mdev_accept. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18sctp: add dif and sdif check in asoc and ep lookupXin Long
This patch at first adds a pernet global l3mdev_accept to decide if it accepts the packets from a l3mdev when a SCTP socket doesn't bind to any interface. It's set to 1 to avoid any possible incompatible issue, and in next patch, a sysctl will be introduced to allow to change it. Then similar to inet/udp_sk_bound_dev_eq(), sctp_sk_bound_dev_eq() is added to check either dif or sdif is equal to sk_bound_dev_if, and to check sid is 0 or l3mdev_accept is 1 if sk_bound_dev_if is not set. This function is used to match a association or a endpoint, namely called by sctp_addrs_lookup_transport() and sctp_endpoint_is_match(). All functions that needs updating are: sctp_rcv(): asoc: __sctp_rcv_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() __sctp_rcv_lookup_harder() __sctp_rcv_init_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() __sctp_rcv_walk_lookup() __sctp_rcv_asconf_lookup() __sctp_lookup_association() -> sctp_addrs_lookup_transport() ep: __sctp_rcv_lookup_endpoint() -> sctp_endpoint_is_match() sctp_connect(): sctp_endpoint_is_peeled_off() __sctp_lookup_association() sctp_has_association() sctp_lookup_association() __sctp_lookup_association() -> sctp_addrs_lookup_transport() sctp_diag_dump_one(): sctp_transport_lookup_process() -> sctp_addrs_lookup_transport() Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-11-18sctp: add skb_sdif in struct sctp_afXin Long
Add skb_sdif function in struct sctp_af to get the enslaved device for both ipv4 and ipv6 when adding SCTP VRF support in sctp_rcv in the next patch. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 04:01:35 +0000