summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-04-16igb: Add double-check MTA_REGISTER for i210 and i211Grzegorz Siwik
Add new function which checks MTA_REGISTER if its filled correctly. If not then writes again to same register. There is possibility that i210 and i211 could not accept MTA_REGISTER settings, specially when you add and remove many of multicast addresses in short time. Without this patch there is possibility that multicast settings will be not always set correctly in hardware. Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-16net/mlx5: Enhance diagnostics info for TX/RX reportersAya Levin
Add ts_format to 'Common Config' section of the TX/RX devlink reporters diagnostics info. Possible values for ts_format: 'RT' or 'FRC' which stands for: Real Time and Free Running Counters correspondingly. Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5: Add helper to initialize 1PPSAya Levin
Wrap 1PPS initialization in a helper for a cleaner init flow. Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Add ethtool extended link stateMoshe Tal
In case the interface was set up but cannot establish the link, ethtool will print more information to help the user troubleshoot the state. For example, no link due to missing cable: $ ethtool eth1 ... Link detected: no (No cable) Beside the general extended state, drivers can pass additional information about the link state using the sub-state field. For example: $ ethtool eth1 ... Link detected: no (Autoneg, No partner detected) The extended state is available only for specific cases, in other cases ethtool with print only "Link detected: no" as before Signed-off-by: Moshe Tal <moshet@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5: Add register layout to support extended link stateMoshe Tal
Add needed structure layouts and defines for pddr register (Port Diagnostics Database Register) and the troublshooting page. This will be used to get extended link state from the monitor opcode bits. Signed-off-by: Moshe Tal <moshet@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5: Allocate FC bulk structs with kvzalloc() instead of kzalloc()Maor Dickman
The bulk size is larger than 16K so use kvzalloc(). The bulk bitmask upper size limit is 16K so use kvcalloc(). Signed-off-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Cleanup safe switch channels API by passing paramsMaxim Mikityanskiy
mlx5e_safe_switch_channels accepts new_chs as a parameter and opens new channels in place, then copying them to priv->channels. It requires all the callers to allocate space for this temporary storage of the new channels. This commit cleans up the API by replacing new_chs with new_params, a meaningful subset of new_chs to be filled by the caller. The temporary space for the new channels is allocated inside mlx5e_safe_switch_params (a new name for mlx5e_safe_switch_channels). An extra copy of params is made, but since it's control flow, it's not critical. Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Refactor on-the-fly configuration changesMaxim Mikityanskiy
This commit extends mlx5e_safe_switch_channels() to support on-the-fly configuration changes, when the channels are open, but don't need to be recreated. Such flows exist when a parameter being changed doesn't affect how the queues are created, or when the queues can be modified while remaining active. Before this commit, such flows were handled as special cases on the caller site. This commit adds this functionality to mlx5e_safe_switch_channels(), allowing the caller to pass a boolean indicating whether it's required to recreate the channels or it's allowed to skip it. The logic of switching channel parameters is now completely encapsulated into mlx5e_safe_switch_channels(). Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Use mlx5e_safe_switch_channels when channels are closedMaxim Mikityanskiy
This commit uses new functionality of mlx5e_safe_switch_channels introduced by the previous commit to reduce the amount of repeating similar code all over the driver. It's very common in mlx5e to call mlx5e_safe_switch_channels when the channels are open, but assign parameters and run hardware commands manually when the channels are closed. After the previous commit it's no longer needed to do such manual things every time, so this commit removes unneeded code and relies on the new functionality of mlx5e_safe_switch_channels. Some of the places are refactored and simplified, where more complex flows are used to change configuration on the fly, without recreating the channels (the logic is rewritten in a more robust way, with a reset required by default and a list of exceptions). Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Allow mlx5e_safe_switch_channels to work with channels closedMaxim Mikityanskiy
mlx5e_safe_switch_channels is used to modify channel parameters and/or hardware configuration in a safe way, so that if anything goes wrong, everything reverts to the old configuration and remains in a consistent state. However, this function only works when the channels are open. When the caller needs to modify some parameters, first it has to check that the channels are open, otherwise it has to assign parameters directly, and such boilerplate repeats in many different places. This commit prepares for the refactoring of such places by allowing mlx5e_safe_switch_channels to work when the channels are closed. In this case it will assign the new parameters and run the preactivate hook. Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: kTLS, Add resiliency to RX resync failuresTariq Toukan
When the TLS logic finds a tcp seq match for a kTLS RX resync request, it calls the driver callback function mlx5e_ktls_resync() to handle it and communicate it to the device. Errors might occur during mlx5e_ktls_resync(), however, they are not reported to the stack. Moreover, there is no error handling in the stack for these errors. In this patch, the driver obtains responsibility on errors handling, adding queue and retry mechanisms to these resyncs. We maintain a linked list of resync matches, and try posting them to the async ICOSQ in the NAPI context. Only possible failure that demands driver handling is ICOSQ being full. By relying on the NAPI mechanism, we make sure that the entries in list will be handled when ICOSQ completions arrive and make some room available. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: TX, Inline function mlx5e_tls_handle_tx_wqe()Tariq Toukan
When TLS is supported, WQE ctrl segment of every transmitted packet is updated with the (possibly empty, for non-TLS packets) TISN field. Take this one-liner function into the header file and inline it, to save the overhead of a function call per packet. While here, remove unused function parameter. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: TX, Inline TLS skb checkTariq Toukan
When TLS is supported and enabled, every transmitted packet is tested to identify if TLS offload is required. Take the early-return condition into an inline function, to save the overhead of a function call for non-TLS packets. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Cleanup unused function parameterTariq Toukan
Socket parameter is not used in accel_rule_init(), remove it. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16net/mlx5e: Remove non-essential TLS SQ state bitTariq Toukan
Maintaining an SQ state bit to indicate TLS support has no real need, a simple and fast test [1] for the SKB is almost equally good. [1] !skb->sk || !tls_is_sk_tx_device_offloaded(skb->sk) Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-16scm: fix a typo in put_cmsg()Eric Dumazet
We need to store cmlen instead of len in cm->cmsg_len. Fixes: 38ebcf5096a8 ("scm: optimize put_cmsg()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16igb: Redistribute memory for transmit packet buffers when in Qav modeEderson de Souza
i210 has a total of 24KB of transmit packet buffer. When in Qav mode, this buffer is divided into four pieces, one for each Tx queue. Currently, 8KB are given to each of the two SR queues and 4KB are given to each of the two SP queues. However, it was noticed that such distribution can make best effort traffic (which would usually go to the SP queues when Qav is enabled, as the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic) perform poorly. Using iperf3 to measure, one could see the performance of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps), with no TSN traffic competing. This patch redistributes the 24KB to each queue equally: 6KB each. On tests, there was no notable performance reduction of best effort traffic performance when there was no TSN traffic competing. Below, more details about the data collected: All experiments were run using the following qdisc setup: qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3 queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1 clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0 index 0 cmd S gatemask 0xf interval 10000000 qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on deadline_mode off skip_sock_check off TSN traffic, when enabled, had this characteristics: Packet size: 1500 bytes Transmission interval: 125us ---------------------------------- Without this patch: ---------------------------------- - TCP data: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1 - TCP data limiting iperf3 buffer size to 4K: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0 - TCP data limiting iperf3 buffer size to 192 bytes (smallest size without serious performance degradation): - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1 - UDP data at 1000Mbit/sec: - No TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%) - With TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%) ---------------------------------- With this patch: ---------------------------------- - TCP data: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1 - TCP data limiting iperf3 buffer size to 4K: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0 - TCP data limiting iperf3 buffer size to 192 bytes (smallest size without serious performance degradation): - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0 - UDP data at 1000Mbit/sec: - No TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%) - With TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%) Signed-off-by: Ederson de Souza <ederson.desouza@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-16Merge tag 'riscv-for-linus-5.12-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes from Palmer Dabbelt: "A handful of fixes: - a fix to properly select SPARSEMEM_STATIC on rv32 - a few fixes to kprobes I don't generally like sending stuff this late, but these all seem pretty safe" * tag 'riscv-for-linus-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: riscv: keep interrupts disabled for BREAKPOINT exception riscv: kprobes/ftrace: Add recursion protection to the ftrace callback riscv: add do_page_fault and do_trap_break into the kprobes blacklist riscv: Fix spelling mistake "SPARSEMEM" to "SPARSMEM"
2021-04-16Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fix from Catalin Marinas: "Fix kernel compilation when using the LLVM integrated assembly. A recent commit (2decad92f473, "arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is set atomically") broke the kernel build when using the LLVM integrated assembly (only noticeable with clang-12 as MTE is not supported by earlier versions and the code in question not compiled). The Fixes: tag in the commit refers to the original patch introducing subsections for the alternative code sequences" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: alternatives: Move length validation in alternative_{insn, endif}
2021-04-16Merge tag 'drm-fixes-2021-04-16' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Daniel Vetter: "I pinged the usual suspects, only intel fixes pending" * tag 'drm-fixes-2021-04-16' of git://anongit.freedesktop.org/drm/drm: drm/i915/display/vlv_dsi: Do not skip panel_pwr_cycle_delay when disabling the panel drm/i915: Don't zero out the Y plane's watermarks drm/i915/dpcd_bl: Don't try vesa interface unless specified by VBT
2021-04-15riscv: keep interrupts disabled for BREAKPOINT exceptionJisheng Zhang
Current riscv's kprobe handlers are run with both preemption and interrupt enabled, this violates kprobe requirements. Fix this issue by keeping interrupts disabled for BREAKPOINT exception. Fixes: c22b0bcb1dd0 ("riscv: Add kprobes supported") Cc: stable@vger.kernel.org Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> [Palmer: add a comment] Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-04-15riscv: kprobes/ftrace: Add recursion protection to the ftrace callbackJisheng Zhang
Currently, the riscv's kprobes(powerred by ftrace) handler is preemptible. Futher check indicates we miss something similar as the commit c536aa1c5b17 ("kprobes/ftrace: Add recursion protection to the ftrace callback"), so do similar modifications as the commit does. Fixes: 829adda597fe ("riscv: Add KPROBES_ON_FTRACE supported") Cc: stable@vger.kernel.org Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-04-15riscv: add do_page_fault and do_trap_break into the kprobes blacklistJisheng Zhang
These two functions are used to implement the kprobes feature so they can't be kprobed. Fixes: c22b0bcb1dd0 ("riscv: Add kprobes supported") Cc: stable@vger.kernel.org Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-04-15riscv: Fix spelling mistake "SPARSEMEM" to "SPARSMEM"Kefeng Wang
There is a spelling mistake when SPARSEMEM Kconfig copy. Fixes: a5406a7ff56e ("riscv: Correct SPARSEMEM configuration") Cc: stable@vger.kernel.org Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-04-15cxl/mem: Fix register block offset calculationBen Widawsky
The "Register Offset Low" register of a "DVSEC Register Locator" contains the 64K aligned offset for the registers along with the BAR indicator and an id. The implementation was treating the "Register Block Offset Low" field a value rather than as a pre-aligned component of the 64-bit offset. So, just mask, don't mask and shift (FIELD_GET). The user visible result of this bug is that the driver fails to bind to the device after none of the required blocks are found. This was missed earlier because the primary development done in the QEMU environment only uses 0 offsets, i.e. 0 shifted is still 0. Fixes: 8adaf747c9f0 ("cxl/mem: Find device capabilities") Reported-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Ben Widawsky <ben.widawsky@intel.com> Link: https://lore.kernel.org/r/20210415232610.603273-1-ben.widawsky@intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-04-15Merge branch 'ehtool-fec-stats'David S. Miller
Jakub Kicinski says: ==================== ethtool: add standard FEC statistics This set adds uAPI for reporting standard FEC statistics, and implements it in a handful of drivers. The statistics are taken from the IEEE standard, with one extra seemingly popular but not standard statistics added. The implementation is similar to that of the pause frame statistics, user requests the stats by setting a bit (ETHTOOL_FLAG_STATS) in the common ethtool header of ETHTOOL_MSG_FEC_GET. Since standard defines the statistics per lane what's reported is both total and per-lane counters: # ethtool -I --show-fec eth0 FEC parameters for eth0: Configured FEC encodings: None Active FEC encoding: None Statistics: corrected_blocks: 256 Lane 0: 255 Lane 1: 1 uncorrectable_blocks: 145 Lane 0: 128 Lane 1: 17 v2: check for errors in mlx5 register access ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15mlx5: implement ethtool::get_fec_statsJakub Kicinski
Report corrected bits. v2: catch reg access errors (Saeed) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15sfc: ef10: implement ethtool::get_fec_statsJakub Kicinski
Report what appears to be the standard block counts: - 30.5.1.1.17 aFECCorrectedBlocks - 30.5.1.1.18 aFECUncorrectableBlocks Don't report the per-lane symbol counts, if those really count symbols they are not what the standard calls for (even if symbols seem like the most useful thing to count.) Fingers crossed that fec_corrected_errors is not in symbols. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15bnxt: implement ethtool::get_fec_statsJakub Kicinski
Report corrected bits. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ethtool: add FEC statisticsJakub Kicinski
Similarly to pause statistics add stats for FEC. The IEEE standard mandates two sets of counters: - 30.5.1.1.17 aFECCorrectedBlocks - 30.5.1.1.18 aFECUncorrectableBlocks where block is a block of bits FEC operates on. Each of these counters is defined per lane (PCS instance). Multiple vendors provide number of corrected _bits_ rather than/as well as blocks. This set adds the 2 standard-based block counters and a extra one for corrected bits. Counters are exposed to user space via netlink in new attributes. Each attribute carries an array of u64s, first element is the total count, and the following ones are a per-lane break down. Much like with pause stats the operation will not fail when driver does not implement the get_fec_stats callback (nor can the driver fail the operation by returning an error). If stats can't be reported the relevant attributes will be empty. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ethtool: fec_prepare_data() - jump to error handlingJakub Kicinski
Refactor fec_prepare_data() a little bit to skip the body of the function and exit on error. Currently the code depends on the fact that we only have one call which may fail between ethnl_ops_begin() and ethnl_ops_complete() and simply saves the error code. This will get hairy with the stats also being queried. No functional changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ethtool: move ethtool_stats_initJakub Kicinski
We'll need it for FEC stats as well. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15scm: optimize put_cmsg()Eric Dumazet
Calling two copy_to_user() for very small regions has very high overhead. Switch to inlined unsafe_put_user() to save one stac/clac sequence, and avoid copy_to_user(). Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge branch 'ch_tlss-fixes'David S. Miller
Vinay Kumar Yadav says: ==================== chelsio/ch_ktls: chelsio inline tls driver bug fixes This series of patches fix following bugs in Chelsio inline tls driver. Patch1: kernel panic. Patch2: connection close issue. Patch3: tcb close call issue. Patch4: unnecessary snd_una update. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ch_ktls: do not send snd_una update to TCB in middleVinay Kumar Yadav
snd_una update should not be done when the same skb is being sent out.chcr_short_record_handler() sends it again even though SND_UNA update is already sent for the skb in chcr_ktls_xmit(), which causes mismatch in un-acked TCP seq number, later causes problem in sending out complete record. Fixes: 429765a149f1 ("chcr: handle partial end part of a record") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ch_ktls: tcb close causes tls connection failureVinay Kumar Yadav
HW doesn't need marking TCB closed. This TCB state change sometimes causes problem to the new connection which gets the same tid. Fixes: 34aba2c45024 ("cxgb4/chcr : Register to tls add and del callback") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ch_ktls: fix device connection closeVinay Kumar Yadav
When sge queue is full and chcr_ktls_xmit_wr_complete() returns failure, skb is not freed if it is not the last tls record in this skb, causes refcount never gets freed and tls_dev_del() never gets called on this connection. Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ch_ktls: Fix kernel panicVinay Kumar Yadav
Taking page refcount is not ideal and causes kernel panic sometimes. It's better to take tx_ctx lock for the complete skb transmit, to avoid page cleanup if ACK received in middle. Fixes: 5a4b9fe7fece ("cxgb4/chcr: complete record tx handling") Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15enetc: convert to schedule_work()Yangbo Lu
Convert system_wq queue_work() to schedule_work() which is a wrapper around it, since the former is a rare construct. Fixes: 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge branch 'hns3-next'David S. Miller
Huazhong Tan says: ==================== net: hns3: updates for -next This series adds support for pushing link status to VFs for the HNS3 ethernet driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15net: hns3: VF not request link status when PF support push link status featureGuangbin Huang
To reduce the processing of unnecessary mailbox command when PF supports actively push its link status to VFs, VFs stop sending request link status command in periodic service task in this case. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15net: hns3: PF add support for pushing link status to VFsGuangbin Huang
Previously, VF updates its link status every second by send query command to PF in periodic service task. If link stats of PF is changed, VF may need at most one second to update its link status. To reduce delay of link status between PF and VFs, PF actively push its link status to VFs when its link status is updated. And to let VF know PF supports this new feature, the link status changed mailbox command adds one bit to indicate it. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15net: phy: at803x: select correct page on config initDavid Bauer
The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit in the chip configure register. The driver assumes the copper side is selected on probe, but this might not be the case depending which page was last selected by the bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior. Select the copper page when probing to circumvent this. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge branch '100GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2021-04-14 This series contains updates to ice driver only. Bruce changes and removes open coded values to instead use existing kernel defines and suppresses false cppcheck issues. Ani adds new VSI states to track netdev allocation and registration. He also removes leading underscores in the ice_pf_state enum. Jesse refactors ITR by introducing helpers to reduce duplicated code and structures to simplify checking of ITR mode. He also triggers a software interrupt when exiting napi poll or busy-poll to ensure all work is processed. Modifies /proc/iomem to display driver name instead of PCI address. He also changes the checks of vsi->type to use a local variable in ice_vsi_rebuild() and removes an unneeded struct member. Jake replaces the driver's adaptive interrupt moderation algorithm to use the kernel's DIM library implementation. Scott reworks module reads to reduce the number of reads needed and remove excessive increment of QSFP page. Brett sets the vsi->vf_id to invalid for non-VF VSIs. Paul removes the return value from ice_vsi_manage_rss_lut() as it's not communicating anything critical. He also reduces the scope of a variable. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge tag 'mlx5-fixes-2021-04-14' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2021-04-14 This series provides 3 small fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15i40e: fix the panic when running bpf in xdpdrv modeJason Xing
Fix this panic by adding more rules to calculate the value of @rss_size_max which could be used in allocating the queues when bpf is loaded, which, however, could cause the failure and then trigger the NULL pointer of vsi->rx_rings. Prio to this fix, the machine doesn't care about how many cpus are online and then allocates 256 queues on the machine with 32 cpus online actually. Once the load of bpf begins, the log will go like this "failed to get tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI failed". Thus, I attach the key information of the crash-log here. BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e] Call Trace: [2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e] [2160294.717666] dev_xdp_install+0x4f/0x70 [2160294.718036] dev_change_xdp_fd+0x11f/0x230 [2160294.718380] ? dev_disable_lro+0xe0/0xe0 [2160294.718705] do_setlink+0xac7/0xe70 [2160294.719035] ? __nla_parse+0xed/0x120 [2160294.719365] rtnl_newlink+0x73b/0x860 Fixes: 41c445ff0f48 ("i40e: main driver core") Co-developed-by: Shujin Li <lishujin@kuaishou.com> Signed-off-by: Shujin Li <lishujin@kuaishou.com> Signed-off-by: Jason Xing <xingwanli@kuaishou.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge tag 'acpi-5.12-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI fix from Rafael Wysocki: "Restore the initrd-based ACPI table override functionality broken by one of the recent fixes" * tag 'acpi-5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: x86: Call acpi_boot_table_init() after acpi_table_upgrade()
2021-04-15Merge tag 'gpio-fixes-for-v5.12-rc8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fix from Bartosz Golaszewski: "A single fix for an older problem with the sysfs interface: do not allow exporting GPIO lines which were marked invalid by the driver" * tag 'gpio-fixes-for-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpio: sysfs: Obey valid_mask
2021-04-15Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid Pull HID fixes from Jiri Kosina: "The changes are all device/driver specific fixes: - EV_KEY and EV_ABS regression fix for Wacom from Ping Cheng - BIOS-specific quirk to fix some of the AMD_SFH-based systems, from Hans de Goede - other small error handling fixes and device ID additions" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: HID: wacom: set EV_KEY and EV_ABS only for non-HID_GENERIC type of devices AMD_SFH: Add DMI quirk table for BIOS-es which don't set the activestatus bits AMD_SFH: Add sensor_mask module parameter AMD_SFH: Removed unused activecontrolstatus member from the amd_mp2_dev struct HID: wacom: Assign boolean values to a bool variable HID cp2112: fix support for multiple gpiochips HID: alps: fix error return code in alps_input_configured() HID: asus: Add support for 2021 ASUS N-Key keyboard HID: google: add don USB id
2021-04-15arm64: alternatives: Move length validation in alternative_{insn, endif}Nathan Chancellor
After commit 2decad92f473 ("arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is set atomically"), LLVM's integrated assembler fails to build entry.S: <instantiation>:5:7: error: expected assembly-time absolute expression .org . - (664b-663b) + (662b-661b) ^ <instantiation>:6:7: error: expected assembly-time absolute expression .org . - (662b-661b) + (664b-663b) ^ The root cause is LLVM's assembler has a one-pass design, meaning it cannot figure out these instruction lengths when the .org directive is outside of the subsection that they are in, which was changed by the .arch_extension directive added in the above commit. Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move length validation inside the subsection") to the alternative_endif macro, shuffling the .org directives so that the length validation happen will always happen in the same subsections. alternative_insn has not shown any issue yet but it appears that it could have the same issue in the future so just preemptively change it. Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences") Cc: <stable@vger.kernel.org> # 5.8.x Link: https://github.com/ClangBuiltLinux/linux/issues/1347 Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-01 22:03:42 +0000