| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/dt
From Stephen Warren:
ARM: bcm2835: device tree updates
The SoC's SDHCI and MMC controllers are added to device tree, and enabled
in the Raspberry Pi board device tree. Some fixed clocks are added to the
device tree to support these drivers. These could be replaced by real
clocks in the future.
A hard-coded memreserve is removed from device tree; the bootloader should
specify the correct memory node content instead, since the memory layout
is dynamic.
This branch is based on v3.8-rc3.
* tag 'bcm2835-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: fix clock node aliasing in device tree
ARM: bcm2835: add I2C controllers to DT
ARM: bcm2835: add SDHCI node to DT
ARM: bcm2835 rpi: remove hard-coded memreserve from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik Device Tree conversion rebased on ARM SoC cleanup branch
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
* tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of <mach/hardware.h>
ARM: nomadik: delete old board files
ARM: nomadik: add I2C devices to the device tree
ARM: nomadik: migrate MMC/SD card support to device tree
ARM: nomadik: convert SMSC91x ethernet to device tree
ARM: nomadik: move GPIO and pinctrl to device tree
ARM: nomadik: add FSMC NAND
ARM: nomadik: move remaining PrimeCells to device tree
ARM: nomadik: move pin maps to cpu file
ARM: nomadik: initial devicetree support
ARM: nomadik: move last custom calls to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
DaVinci DT changes for v3.9
This pull requests adds support for pinctrl, NAND
and RTC support when DA850 is booting using DT.
* tag 'davinci-for-v3.9/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: add RTC DT entries
ARM: davinci: da850: move interrupt-parent property to soc node
ARM: davinci: da8xx defconfig: enable pinctrl config option
ARM: davinci: da850: add NAND driver DT entries
ARM: davinci: da850: add pinctrl driver DT entries
|
|
This was only used from the core machine, source it into the machine
file and delete, also convert all direct references using the
physical-to-virtual macros in this file to ioremap() and only
default-remap the 4K used by the debug UART.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Device Tree support on Nomadik can do everything the old board
files could do, so delete the old board files and make the nomadik
select CONFIG_OF.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the GPIO-based I2C devices to the Nomadik device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves over the MMC/SD card support to the device tree probe
path. The special GPIO to bias the card detect line is kept,
but the pin property is moved to the device tree as part of
the MMC/SD card node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This converts the SMSC91x ethernet controller to use device
tree. The existing solution from the board file, to request the
GPIO triggering the ethernet IRQ from the board file is kept
for the time being, but the GPIO number assignment is moved
over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves the instances of the Nomadik pin controller and the
Nomadik GPIO blocks (also handled by the GPIO driver) over to
the device tree. A new compatible string is added to the
pin control driver in the process.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The two remaining PrimeCells, RNG and RTC, are migrated to the
device tree for device tree boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move the pinctrl maps over to the CPU file and register them
right before the pin controller itself. This way the pinmaps
will also benefit the device tree boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Support basic device tree boot on the Nomadik. Implement the
support in the cpu file with the intent of deleting the board
files later. At this stage IRQ controllers, system timer,
l2x0 cache, UARTs and thus console boot is fully functional.
Patch out the code adding devices by initcalls for now so
as not to disturb the boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The I2C pins were still set up using custom nmk_* calls, move
these to use the pinctrl mapping table instead. There was also
a remaining call to turn the Ethernet pin to GPIO, and this is
now done implicitly by the GPIO-to-pinctrl range translation
calls.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add RTC DT entries in da850 dts file.
Tested on da850-evm device.
Test Procedure:
$ date 2013.01.28-10:00:00 # usage: date[YYYY.]MM.DD-hh:mm[:ss]
$ hwclock -w
(reset board and check system time)
Signed-off-by: Mrugesh Katepallewar <mrugesh.mk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This patch moves 'interrupt-parent' property to soc node, so that
the child inherits this property. This avoids adding 'interrupt-parent'
property to each node.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"It turns out that we had two crc bugs when running fsx-linux in a
loop. Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
all down. Miao also has a new OOM fix in this v2 pull as well.
Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
and resuming a running balance across drives.
Josef's orphan truncate patch fixes an obscure corruption we'd see
during xfstests.
Arne's patches address problems with subvolume quotas. If the user
destroys quota groups incorrectly the FS will refuse to mount.
The rest are smaller fixes and plugs for memory leaks."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
Btrfs: fix repeated delalloc work allocation
Btrfs: fix wrong max device number for single profile
Btrfs: fix missed transaction->aborted check
Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
Btrfs: put csums on the right ordered extent
Btrfs: use right range to find checksum for compressed extents
Btrfs: fix panic when recovering tree log
Btrfs: do not allow logged extents to be merged or removed
Btrfs: fix a regression in balance usage filter
Btrfs: prevent qgroup destroy when there are still relations
Btrfs: ignore orphan qgroup relations
Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
Btrfs: fix unlock order in btrfs_ioctl_rm_dev
Btrfs: fix unlock order in btrfs_ioctl_resize
Btrfs: fix "mutually exclusive op is running" error code
Btrfs: bring back balance pause/resume logic
btrfs: update timestamps on truncate()
btrfs: fix btrfs_cont_expand() freeing IS_ERR em
Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
Btrfs: fix off-by-one in lseek
...
|
|
Pull cifs fixes from Steve French:
"Two small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
cifs: fix srcip_matches() for ipv6
|
|
Pull kvm fixlet from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Emulate dcbf
|
|
Pull ARM fixes from Russell King:
"A number of fixes:
Patrik found a problem with preempt counting in the VFP assembly
functions which can cause the preempt count to be upset.
Nicolas fixed a problem with the parsing of the DT when it straddles a
1MB boundary.
Subhash Jadavani reported a problem with sparsemem and our highmem
support for cache maintanence for DMA areas, and TI found a bug in
their strongly ordered memory mapping type.
Also, three fixes by way of Will Deacon's tree from Dave Martin for
instruction compatibility and Marc Zyngier to fix hypervisor boot mode
issues."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
ARM: virt: simplify __hyp_stub_install epilog
ARM: virt: boot secondary CPUs through the right entry point
ARM: virt: Avoid bx instruction for compatibility with <=ARMv4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
- cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
- ACPI cpufreq fix from Thomas Schlichter.
- cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
- APEI workaround for incorrect BIOS information from Lans Zhang.
* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Add module aliases for acpi-cpufreq
ACPI: Check MSR valid bit before using P-state frequencies
PM / devfreq: exynos4_bus: honor RCU lock usage
PM / devfreq: add locking documentation for recommended_opp
cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
cpufreq: OMAP: use RCU locks around usage of OPP
ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
ACPI / processor: Get power info before updating the C-states
powernow-k8: Add a kconfig dependency on acpi-cpufreq
ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
intel_idle: Don't register CPU notifier if we are not running.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"One more oversight in the debugfs code was reported and fixed, plus a
documentation fix."
* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix small typo in regmap_bulk_write comment
regmap: debugfs: Fix seeking from the cache
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
|
|
git://git.pengutronix.de/git/wsa/linux
Pill i2c fixes from Wolfram Sang:
"Here are a few, typical driver fixes for the I2C subsystem"
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c-designware: add missing MODULE_LICENSE
i2c: omap: fix draining irq handling
i2c: omap: errata i462: fix incorrect ack for arbitration lost interrupt
i2c: muxes: fix wrong use of sizeof(ptr)
i2c: sirf: register i2c_client from dt child-nodes in probe entry
i2c: mxs: Fix type of error code
i2c: mxs: Fix misuse init_completion
|
|
btrfs_start_delalloc_inodes() locks the delalloc_inodes list, fetches the
first inode, unlocks the list, triggers btrfs_alloc_delalloc_work/
btrfs_queue_worker for this inode, and then it locks the list, checks the
head of the list again. But because we don't delete the first inode that it
deals with before, it will fetch the same inode. As a result, this function
allocates a huge amount of btrfs_delalloc_work structures, and OOM happens.
Fix this problem by splice this delalloc list.
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
The max device number of single profile is 1, not 0 (0 means 'as many as
possible'). Fix it.
Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
First, though the current transaction->aborted check can stop the commit early
and avoid unnecessary operations, it is too early, and some transaction handles
don't end, those handles may set transaction->aborted after the check.
Second, when we commit the transaction, we will wake up some worker threads to
flush the space cache and inode cache. Those threads also allocate some transaction
handles and may set transaction->aborted if some serious error happens.
So we need more check for ->aborted when committing the transaction. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
We may access and update transaction->aborted on the different CPUs without
lock, so we need ACCESS_ONCE() wrapper to prevent the compiler from creating
unsolicited accesses and make sure we can get the right value.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
I noticed a WARN_ON going off when adding csums because we were going over
the amount of csum bytes that should have been allowed for an ordered
extent. This is a leftover from when we used to hold the csums privately
for direct io, but now we use the normal ordered sum stuff so we need to
make sure and check if we've moved on to another extent so that the csums
are added to the right extent. Without this we could end up with csums for
bytenrs that don't have extents to cover them yet. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
For compressed extents, the range of checksum is covered by disk length,
and the disk length is different with ram length, so we need to use disk
length instead to get us the right checksum.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
A user reported a BUG_ON(ret) that occured during tree log replay. Ret was
-EAGAIN, so what I think happened is that we removed an extent that covered
a bitmap entry and an extent entry. We remove the part from the bitmap and
return -EAGAIN and then search for the next piece we want to remove, which
happens to be an entire extent entry, so we just free the sucker and return.
The problem is ret is still set to -EAGAIN so we trip the BUG_ON(). The
user used btrfs-zero-log so I'm not 100% sure this is what happened so I've
added a WARN_ON() to catch the other possibility. Thanks,
Reported-by: Jan Steffens <jan.steffens@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
We drop the extent map tree lock while we're logging extents, so somebody
could come in and merge another extent into this one and screw up our
logging, or they could even remove us from the list which would keep us from
logging the extent or freeing our ref on it, so we need to make sure to not
clear LOGGING until after the extent is logged, and then we can merge it to
adjacent extents. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
|
into fixes
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
|
|
From Nicolas Ferre:
Here are fixes for AT91 that are mainly related to device tree.
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
|
|
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
As the kernel is able to cope with multiple clusters,
uncomment the A7 cores in the Device Tree for V2P-CA15_A7
tile, making all 5 cores available to the user.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
In ARM multi-cluster systems the MPIDR affinity level 0 cannot be used as a
single cpu identifier, affinity levels 1 and 2 must be taken into account as
well.
This patch extends the MPIDR usage to affinity levels 1 and 2 in versatile
secondary cores start up code in order to compare the passed pen_release
value with the full-blown affinity mask.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
|
|
Enable pinctrl related config option in da8xx_omapl_defconfig
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
This is yet another critical imxfb fixes held off by absence of FB
maintainer for some time.
* tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: imxfb: Do not crash on reboot
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB fixes from Greg Kroah-Hartman:
"Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver
build issues (it's just some code moving around and being deleted)."
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: fix build error in ehci-mxc
USB: EHCI: add a name for the platform-private field
USB: EHCI: fix incorrect configuration test
USB: EHCI: Move definition of EHCI_STATS to ehci.h
USB: UHCI: fix IRQ race during initialization
usb: gadget: FunctionFS: Fix missing braces in parse_opts
usb: dwc3: gadget: fix ep->maxburst for ep0
ARM: i.MX clock: Change the connection-id for fsl-usb2-udc
usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremap
usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_id
usb: musb: cppi_dma: drop '__init' annotation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull drivers/misc fix from Greg Kroah-Hartman:
"Here is a single revert for the ti-st misc driver, fixing problem that
was introduced in 3.7-rc1 that has been bothering people."
* tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "drivers/misc/ti-st: remove gpio handling"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY maintainer patch from Greg Kroah-Hartman:
"Just a MAINTAINERS update, now that Alan has left for a bit, I'll
continue to watch over the serial drivers."
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
MAINTAINERS: Someone needs to watch over the serial drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- gspca: add needed delay for I2C traffic for sonixb/sonixj cameras
- gspca: add one missing Kinect USB ID
- usbvideo: some regression fixes
- omap3isp: fix some build issues
- videobuf2: fix video output handling
- exynos s5p/m5mols: a few regression fixes.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
[media] omap3isp: Don't include <plat/cpu.h>
[media] s5p-mfc: Fix interrupt error handling routine
[media] s5p-fimc: Fix return value of __fimc_md_create_flite_source_links()
[media] m5mols: Fix typo in get_fmt callback
[media] v4l: vb2: Set data_offset to 0 for single-plane output buffers
[media] [FOR,v3.8] omap3isp: Don't include deleted OMAP plat/ header files
[media] gspca_sonixj: Add a small delay after i2c_w1
[media] gspca_sonixb: Properly wait between i2c writes
[media] gspca_kinect: add Kinect for Windows USB id
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"The asm-generic changeset has been ack'ed by Arnd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up finit_module
asm-generic/dma-mapping-broken.h: Provide dma_alloc_attrs()/dma_free_attrs()
m68k: Provide dma_alloc_attrs()/dma_free_attrs()
|
