| Age | Commit message (Collapse) | Author |
|---|
|
The non-mmio pinctrl node is not supposed to be inside the soc simple-bus
as dtc points out:
../arch/arm64/boot/dts/rockchip/rk3562.dtsi:1115.20-1181.5: Warning (simple_bus_reg): /soc/pinctrl: missing or empty reg/ranges property
Move the pinctrl node outside and adapt the indentation.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-7-heiko@sntech.de
|
|
The rk3562 pcie node currently uses the apb register as its unit address
which is the second reg area defined in the binding.
As can be seen by the dtc warnings like
../arch/arm64/boot/dts/rockchip/rk3562.dtsi:624.26-675.5: Warning (simple_bus_reg): /soc/pcie@ff500000: simple-bus unit address format error, expected "fe000000"
using the first reg area as the unit address seems to be preferred.
This is the dbi area per the binding, so adapt the unit address accordingly
and move the nodes to their new position.
With the move also move the reg + reg-names below the compatible, as is the
preferred position.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-6-heiko@sntech.de
|
|
The non-mmio pinctrl node is not supposed to be inside the soc simple-bus
as dtc points out:
../arch/arm64/boot/dts/rockchip/rk3528.dtsi:870.20-936.5: Warning (simple_bus_reg): /soc/pinctrl: missing or empty reg/ranges property
Move the pinctrl node outside and adapt the indentation.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-5-heiko@sntech.de
|
|
Two empty lines between nodes, is one too many.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-4-heiko@sntech.de
|
|
The non-mmio pinctrl node is not supposed to be inside the soc simple-bus
as dtc points out:
../arch/arm64/boot/dts/rockchip/rk3576.dtsi:2351.20-2417.5: Warning (simple_bus_reg): /soc/pinctrl: missing or empty reg/ranges property
Move the pinctrl node outside and adapt the indentation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505150745.PQT9TLYX-lkp@intel.com/
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-3-heiko@sntech.de
|
|
The rk3576 pcie nodes currently use the apb register as their unit address
which is the second reg area defined in the binding.
As can be seen by the dtc warnings like
../arch/arm64/boot/dts/rockchip/rk3576.dtsi:1346.24-1398.5: Warning (simple_bus_reg): /soc/pcie@2a200000: simple-bus unit address format error, expected "22000000"
../arch/arm64/boot/dts/rockchip/rk3576.dtsi:1400.24-1452.5: Warning (simple_bus_reg): /soc/pcie@2a210000: simple-bus unit address format error, expected "22400000"
using the first reg area as the unit address seems to be preferred.
This is the dbi area per the binding, so adapt the unit address accordingly
and move the nodes to their new position.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505150745.PQT9TLYX-lkp@intel.com/
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250518220449.2722673-2-heiko@sntech.de
|
|
The assigned-clocks and assigned-clock-rates properties were moved from
the scmi_clk node onto cpu nodes in commit
87810bda8a84 ("arm64: dts: rockchip: Fix SCMI assigned clocks on rk3588s")
During review of v1 of that patch set, the following comment was made:
why aren't you using OPP tables to define CPU frequencies.
Assigned-clocks looks like a temporary hack because you haven't
done proper OPP tables.
Some time later, proper OPP tables for rk3588 were added in commit
276856db91b4 ("arm64: dts: rockchip: Add OPP data for CPU cores on RK3588")
So this 'temporary hack' is no longer needed.
Dropping it fixes the following dtb validation issues:
cpu@0: Unevaluated properties are not allowed
('assigned-clock-rates', 'assigned-clocks' were unexpected)
cpu@400: Unevaluated properties are not allowed
('assigned-clock-rates', 'assigned-clocks' were unexpected)
cpu@600: Unevaluated properties are not allowed
('assigned-clock-rates', 'assigned-clocks' were unexpected)
Link: https://lore.kernel.org/linux-rockchip/CAL_JsqL_EogoKOQ1xwU75=rJSC4o7yV3Jej4vadtacX2Pt3-hw@mail.gmail.com/
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250519101909.62754-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the power-domains for the RK3576 SFC nodes according to the
TRM part 1. This fixes potential SErrors when accessing the SFC
registers without other peripherals (e.g. eMMC) doing a prior
power-domain enable. For example this is easy to trigger on the
Rock 4D, which enables the SFC0 interface, but does not enable
the eMMC interface at the moment.
Cc: stable@vger.kernel.org
Fixes: 36299757129c8 ("arm64: dts: rockchip: Add SFC nodes for rk3576")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250520-rk3576-fix-fspi-pmdomain-v1-1-f07c6e62dadd@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The NanoPi R5S has 4 GPIO LEDs, a RED one for SYStem power and 3 green
LEDs meant to indicate that a cable is connected to either of the
2.5GbE LAN ports or the 1GbE WAN port.
In the NanoPi R5S schematic (2204; page 19) as well as on the PCB and on
the case, SYS is used and not POWER. So replace 'power' with 'sys'.
But keep the 'power_led' label/phandle even though the kernel doesn't
use it, but it may be used outside of it.
The SYStem LED already had "heartbeat" as its default-trigger.
Set the default-trigger to "netdev" for the NICs so they will show when
LAN1/LAN2/WAN is connected and set their default-state to "off".
Also assign labels as close as possible to the labels on the case, while
still being descriptive enough in their own right.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250513170056.96259-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
PP1516 are Touchscreen devices built around the PX30 SoC and companion
devices to PX30-Cobra, again with multiple display options.
The devices feature an EMMC, OTG port and a 720x1280 display with a
touchscreen and camera
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-7-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
PP1516 are Touchscreen devices built around the PX30 SoC and companion
devices to PX30-Cobra, again with multiple display options.
The devices feature an EMMC, OTG port and a 720x1280 display with a
touchscreen and camera
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-6-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Cobra are Touchscreen devices built around the PX30 SoC using
a variety of display options.
The devices feature an EMMC, network port, usb host + OTG ports and
a 720x1280 display with a touchscreen.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-5-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Cobra are Touchscreen devices built around the PX30 SoC using
a variety of display options.
The devices feature an EMMC, network port, usb host + OTG ports and
a 720x1280 display with a touchscreen.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Using snps,reset-* properties to handle the ethernet-phy resets is
deprecated and instead a real phy node should be used.
Move the Ringneck phy-reset properties to such a node
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Using snps,reset-* properties for handling the phy-reset is deprecated
and instead a real phy node should be defined that then contains the
reset-gpios handling.
To facilitate this, add the core mdio node under the px30's gmac, similar
to how the other Rockchip socs already do this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250514150745.2437804-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Puma with Haikou
The u2phy0_host port is the part of the USB PHY0 (namely the
HOST0_DP/DM lanes) which routes directly to the USB2.0 HOST
controller[1]. The other lanes of the PHY are routed to the USB3.0 OTG
controller (dwc3), which we do use.
The HOST0_DP/DM lanes aren't routed on RK3399 Puma so let's simply
disable the USB2.0 controllers.
USB3 OTG has been known to be unstable on RK3399 Puma Haikou for a
while, one of the recurring issues being that only USB2 is detected and
not USB3 in host mode. Reading the justification above and seeing that
we are keeping u2phy0_host in the Haikou carrierboard DTS probably may
have bothered you since it should be changed to u2phy0_otg. The issue is
that if it's switched to that, USB OTG on Haikou is entirely broken. I
have checked the routing in the Gerber file, the lanes are going to the
expected ball pins (that is, NOT HOST0_DP/DM).
u2phy0_host is for sure the wrong part of the PHY to use, but it's the
only one that works at the moment for that board so keep it until we
figure out what exactly is broken.
No intended functional change.
[1] https://rockchip.fr/Rockchip%20RK3399%20TRM%20V1.3%20Part2.pdf
Chapter 2 USB2.0 PHY
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-5-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The u2phy1_host port is the part of the USB PHY1 (namely the
HOST1_DP/DM lanes) which routes directly to the USB2.0 HOST
controller[1]. The other lanes of the PHY are routed to the USB3.0 OTG
controller (dwc3), which we do use.
The HOST1_DP/DM lanes aren't routed on RK3399 Puma so let's simply
disable the USB2.0 controllers and associated part in USB2.0 PHY.
No intended functional change.
[1] https://rockchip.fr/Rockchip%20RK3399%20TRM%20V1.3%20Part2.pdf
Chapter 2 USB2.0 PHY
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-4-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Currently, the onboard Cypress CYUSB3304 USB hub is not defined in
the device tree, and hub reset pin is provided as vcc5v0_host
regulator to usb phy. This causes instability issues, as a result
of improper reset duration.
The fixed regulator device requests the GPIO during probe in its
inactive state (except if regulator-boot-on property is set, in
which case it is requested in the active state). Considering gpio
is GPIO_ACTIVE_LOW for Puma, it means it’s driving it high. Then
the regulator gets enabled (because regulator-always-on property),
which drives it to its active state, meaning driving it low.
The Cypress CYUSB3304 USB hub actually requires the reset to be
asserted for at least 5 ms, which we cannot guarantee right now
since there's no delay in the current config, meaning the hub may
sometimes work or not. We could add delay as offered by
fixed-regulator but let's rather fix this by using the proper way
to model onboard USB hubs.
Define hub_2_0 and hub_3_0 nodes, as the onboard Cypress hub
consist of two 'logical' hubs, for USB2.0 and USB3.0.
Use the 'reset-gpios' property of hub to assign reset pin instead
of using regulator. Rename the vcc5v0_host regulator to
cy3304_reset to be more meaningful. Pin is configured to
output-high by default, which sets the hub in reset state
during pin controller initialization. This allows to avoid double
enumeration of devices in case the bootloader has setup the USB
hub before the kernel.
The vdd-supply and vdd2-supply properties in hub nodes are
added to provide correct dt-bindings, although power supplies are
always enabled based on HW design.
Fixes: 2c66fc34e945 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Cc: stable@vger.kernel.org # 6.6
Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-3-4a76a474a010@thaumatec.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Cypress HX3 hubs use different default PID value depending
on the variant. Update compatibles list.
Becasuse all hub variants use the same driver data, allow the
dt node to have two compatibles: leftmost which matches the HW
exactly, and the second one as fallback.
Fixes: 1eca51f58a10 ("dt-bindings: usb: Add binding for Cypress HX3 USB 3.0 family")
Cc: stable@vger.kernel.org # 6.6
Cc: stable@vger.kernel.org # Backport of the patch ("dt-bindings: usb: usb-device: relax compatible pattern to a contains") from list: https://lore.kernel.org/linux-usb/20250418-dt-binding-usb-device-compatibles-v2-1-b3029f14e800@cherry.de/
Cc: stable@vger.kernel.org # Backport of the patch in this series fixing product ID in onboard_dev_id_table in drivers/usb/misc/onboard_usb_dev.c driver
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-2-4a76a474a010@thaumatec.com
[taken with Greg's blessing]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Even though they will be the same for all boards, i2c and uart aliases
are supposed to live in the individual board files, to not create
aliases for disabled nodes.
So move the newly added aliases for rk3528 over to the Radxa E20C board,
which is the only rk3528 board right now.
Fixes: d3a05f490d04 ("arm64: dts: rockchip: Add I2C controllers for RK3528")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250510220106.2108414-1-heiko@sntech.de
|
|
As described, the analogix-dp controller on rk3588 only supports 2 clocks
and the edp0 node handles that correctly.
The edp1 node on the other hand seems to have a dangling 3rd clock called
spdif, that probably only exists in the vendor-tree.
As that is not handled at all, remove it for now so that we adhere to the
binding.
Fixes: a481bb0b1ad9 ("arm64: dts: rockchip: Add eDP1 dt node for rk3588")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250509152329.2004073-1-heiko@sntech.de
|
|
DRAM: DDR4
Storage: eMMC
PMIC: RK809
Audio: Headphone and speaker
Interface:
- USB3.0 HOST
- USB2.0 HOST
- PCIe x4 slot(pcie2x1 available)
- SD card slot
- GMAC
- debug UART0
NOTE: the USB3.0 and the PCIe reuse the comboPHY, so the USB3.0 work in
USB2 only mode.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20250509102308.761424-6-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3562 is a SoC from Rockchip, which embedded with quad
ARM Cortex-A53.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20250509102308.761424-5-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add device tree documentation for rk3562-evb2-v10.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250509102308.761424-4-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add all syscon compatibles for rk3562.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250509102308.761424-3-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the compatible for the pmu mfd on rk3562.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250509102308.761424-2-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Radxa E20C has two GbE ports, LAN and WAN. The LAN port is provided
using a GMAC controller and a YT8531C PHY and the WAN port is provided
by an RTL8111H PCIe Ethernet controller.
Enable support for the LAN port on Radxa E20C.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250509202402.260038-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Rockchip RK3528 has two Ethernet controllers based on Synopsys DWC
Ethernet QoS IP.
Add device tree nodes for the two Ethernet controllers in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250509202402.260038-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add ROCK 5B+, which is an improved version of the ROCK 5B with the
following changes:
* Memory LPDDR4X -> LPDDR5
* HDMI input connector size
* eMMC socket -> onboard
* M.2 E-Key is replaced by onboard RTL8852BE WLAN/BT
* M.2 M-Key 1x4 lanes is replaced by 2x2 lanes
* Added M.2 B-Key for USB connected WWAN modules (untested)
* Add second camera port (not yet supported in upstream Linux)
* Add dedicated USB-C port for device power (no impact in DT;
the existing port has not been changed and the new port is
handled by CH224D standalone chip)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250508-rock5bp-for-upstream-v2-4-677033cc1ac2@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Radxa ROCK 5B+ is an improved version of the ROCK 5B.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250508-rock5bp-for-upstream-v2-3-677033cc1ac2@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Radxa released some more boards, which are based on the original
Rock 5B. Move its board description into an include file to avoid
unnecessary duplication.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250508-rock5bp-for-upstream-v2-1-677033cc1ac2@kernel.org
Link: https://lore.kernel.org/r/20250508-rock5bp-for-upstream-v2-2-677033cc1ac2@kernel.org
[The original submission was split into two elements, renaming the file
and then moving some nodes around. This was done to make review easier
due to the diff being smaller. This commit is a squash of both of them
to facilitate bisectability and was also intended by the original author]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
General feature for rk3399 industry evaluation board:
- Rockchip RK3399
- 4GB LPDDR4
- emmc5.1
- SDIO3.0 compatible TF card
- 1x HDMI2.0a TX
- 1x HDMI1.4b RX with TC358749XBG HDMI to MIPI CSI2 bridge chip
- 1x type-c DisplayPort
- 3x USB3.0 Host
- 1x USB2.0 Host
- 1x Ethernet / USB3.0 to Ethernet
Tested with HDMI/GPU/USB2.0/USB3.0/TF card/emmc.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Link: https://lore.kernel.org/r/20250506034347.57-3-kernel@airkyi.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree binding for the rk3399 industry evaluation board.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250506034347.57-2-kernel@airkyi.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
With the hdmi_sound node added to the base RK3576 SoC tree, we can now
enable it on the Sige5 SBC.
Do this, and also enable the corresponding SAI6 audio controller node.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250506-rk3576-sai-v4-4-a8b5f5733ceb@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The ArmSoM Sige5 board features an Everest ES8388 codec to provide
analog stereo audio output, as well as analog audio input. The codec
hangs off the i2c2 bus and responds to address 0x10. It is connected to
the SAI1 audio controller of the RK3576, with one SDO (output) lane and
one SDI (input) lane.
The codec has two sets of outputs. One set, LOUT1/ROUT1, is connected
through a set of 22uF non-polarised coupling capacitors to a 3-position
connector that appears to be a clone of the JST BM03B-SURS-TF header,
and is capable of mating with a JST 03SUR-32S (or JST 03SUR-36L if you
prefer lemon-lime) or compatible clone connector. The right headphone
output is the one closest to the Type-C DC input connector, the left
headphone output is the one in the middle, and the third position, the
one closest to the USB3 Type-A host connector, is puzzingly labelled as
"HP_GND" in the schematic but is in fact connected to the codecs RIN1
input through a 1uF non-plarised coupling capacitor.
LOUT2 and ROUT2 are routed to 1mm test pads T36 and T37 respectively.
These are located on the bottom of the board, and do not go through any
coupling capacitor. For use as line out, the ES8388 datasheet recommends
adding 1uF coupling capacitor if one wishes to use it as a line-level
output.
There is also a pair of inputs for a stereo microphone, going from two
1mm testpads T34 and T35, which are decoupled with a 100pF capacitor and
pulled to 3.3v and ground respectively. These inputs then go through 1uF
capacitors each and end up in the LINPUT2 and RINPUT2 pins of the
ES8388 codec.
The codec's power inputs are routed to receive 3.3V for both its analog
and digital inputs, though from different supplies.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250506-rk3576-sai-v4-3-a8b5f5733ceb@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3576 SoC now has upstream support for HDMI.
Add an HDMI audio node, which uses SAI6 as its audio controller
according to downstream.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250506-rk3576-sai-v4-2-a8b5f5733ceb@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3576 SoC has 10 SAI controllers in total. Five of them are in the
video output power domains, and are used for digital audio output along
with the video signal of those, e.g. HDMI audio.
The other five, SAI0 through SAI4, are exposed externally. SAI0 and SAI1
are capable of 8-channel audio, whereas SAI2, SAI3 and SAI4 are limited
to two channels. These five are in the audio power domain.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250506-rk3576-sai-v4-1-a8b5f5733ceb@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
SD-card is available on Radxa E20C board.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250508234829.27111-4-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3528 features two SDIO controllers and one SD/MMC controller, describe
them in devicetree. Since their sample and drive clocks are located in
the VO and VPU GRFs, corresponding syscons are added to make these
clocks available.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250508234829.27111-3-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
These clocks are for SD/SDIO tuning purpose and come with registers
in GRF syscon.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250506092206.46143-2-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Following commit b956c9de9175 ("arm64: dts: rockchip: rk356x: Move
PCIe MSI to use GIC ITS instead of MBI"), change the PCIe3 controller's
MSI on rk3568 to use ITS, so that all MSI-X can work properly.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20250308093008.568437-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the 3.3v and 1.8v regulators that are connected to
the eMMC on the R5 series devices, as well as adding the
eMMC data strobe, and enable eMMC HS200 mode as the
Foresee FEMDNN0xxG-A3A55 modules support it.
Fixes: c8ec73b05a95d ("arm64: dts: rockchip: create common dtsi for NanoPi R5 series")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250506222531.625157-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
As described in the radxa_rock_3c_v1400_schematic.pdf, the SPI Flash's
VCC connector is connected to VCCIO_FLASH and according to the
that same schematic, that belongs to the VCC_1V8 power source.
This fixes the following warning:
spi-nor spi4.0: supply vcc not found, using dummy regulator
Fixes: ee219017ddb5 ("arm64: dts: rockchip: Add Radxa ROCK 3C")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20250506195702.593044-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable pwm and fixed regulators for Radxa E20C. The pwm regulator is
used to power the CPU and GPU. Note that the LPDDR4 voltage is 1.1V.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250401120020.976343-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add pwm nodes for RK3528. The PWM core on RK3528 is the same as
RK3328, but the driver does not support interrupts yet.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250401120020.976343-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Radxa E20C ships an onboard I2C EEPROM for storing production
information. Enable it in devicetree.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250417120118.17610-6-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Describe I2C controllers shipped by RK3528 in devicetree. For I2C-2,
I2C-4 and I2C-7 which come with only a set of possible pins, a default
pin configuration is included.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250417120118.17610-5-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Certain clocks on the RK3576 are additionally essentially "gated" behind
some bit toggles in the IOC GRF range. Downstream ungates these by
adding a separate clock driver that maps over the GRF range and leaks
their implementation of this into the DT.
Instead, define some new clock IDs for these, so that consumers of these
types of clocks can properly articulate which clock they're using, so
that we can then add them to the clock driver for SoCs that need them.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250502-rk3576-sai-v3-1-376cef19dd7c@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3576 has a hardware random number generator IP built into the SoC.
Add it to the SoC's .dtsi, now that there's a binding and driver for it.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250430-rk3576-hwrng-v1-3-480c15b5843e@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
