| Age | Commit message (Collapse) | Author |
|---|
|
Commit eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE
interrupt controller") introduced support for the XIVE exploitation
mode of the P9 interrupt controller on the pseries platform.
At that time, support for CPU removal was not complete on PowerVM and
CPU hot unplug remained untested. It appears that some cleanups of the
XIVE internal structures are required before releasing the CPU,
without which the kernel crashes in a RTAS call doing the CPU
isolation.
These changes fix the crash by deconfiguring the IPI interrupt source
and clearing the event queues of the CPU when it is removed.
Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When resetting an IPI, hw_ipi should also be set to zero.
Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently, NVMe PCI host driver is programming CMB dma address as
I/O SQs addresses. This results in failures on systems where 1:1
outbound mapping is not used (example Broadcom iProc SOCs) because
CMB BAR will be progammed with PCI bus address but NVMe PCI EP will
try to access CMB using dma address.
To have CMB working on systems without 1:1 outbound mapping, we
program PCI bus address for I/O SQs instead of dma address. This
approach will work on systems with/without 1:1 outbound mapping.
Based on a report and previous patch from Abhishek Shah.
Fixes: 8ffaadf7 ("NVMe: Use CMB for the IO SQes if available")
Cc: stable@vger.kernel.org
Reported-by: Abhishek Shah <abhishek.shah@broadcom.com>
Tested-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
To declare gpio interrupt line for STMPE1600, 2 possibilities are offered:
-use gpio binding (and then the gpiolib interface inside driver)
-use interrupt binding as each gpio-controller are also interrupt controller
on stm32f429.
In STMPE 1600 node both (gpio and interrupt) bindings are defined.
This patch fixes this issue and use only interrupt binding.
Fixes: c04b2e72af8d ("ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The variable is unused when the softlockup detector is disabled in Kconfig.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The function names made sense up to the point where the watchdog
(re)configuration was unified to use softlockup_reconfigure_threads() for
all configuration purposes. But that includes scenarios which solely
configure the nmi watchdog.
Rename softlockup_reconfigure_threads() and softlockup_init_threads() so
the function names match the functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
|
|
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.
The first call is via:
start_wd_on_cpu+0x80/0x2f0
watchdog_nmi_reconfigure+0x124/0x170
softlockup_reconfigure_threads+0x110/0x130
lockup_detector_init+0xbc/0xe0
kernel_init_freeable+0x18c/0x37c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0xbc
And then again via the CPU hotplug registration:
start_wd_on_cpu+0x80/0x2f0
cpuhp_invoke_callback+0x194/0x620
cpuhp_thread_fun+0x7c/0x1b0
smpboot_thread_fn+0x290/0x2a0
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xbc
This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
|
|
Instead of dropping the cpu hotplug lock after stopping NMI watchdog and
threads and reaquiring for restart, the code and the protection rules
become more obvious when holding cpu hotplug lock across the full
reconfiguration.
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710022105570.2114@nanos
|
|
The recent cleanup of the watchdog code split watchdog_nmi_reconfigure()
into two stages. One to stop the NMI and one to restart it after
reconfiguration. That was done by adding a boolean 'run' argument to the
code, which is functionally correct but not necessarily a piece of art.
Replace it by two explicit functions: watchdog_nmi_stop() and
watchdog_nmi_start().
Fixes: 6592ad2fcc8f ("watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage")
Requested-by: Linus 'Nursing his pet-peeve' Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas 'Mopping up garbage' Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710021957480.2114@nanos
|
|
vt has a mixture of pr_<level> and printk.
Convert to using only pr_<level>.
Miscellanea:
o Coalesce formats
o Realign arguments
o Add missing braces around an if/else with the printk conversion
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled,
echo 1 >/proc/sys/kernel/sysrq
echo p >/proc/sysrq-trigger
kernel will print call trace as below:
sysrq: SysRq : Show Regs
BUG: using __this_cpu_read() in preemptible [00000000] code: sh/435
caller is __this_cpu_preempt_check+0x18/0x20
Call trace:
[<ffffff8008088e80>] dump_backtrace+0x0/0x1d0
[<ffffff8008089074>] show_stack+0x24/0x30
[<ffffff8008447970>] dump_stack+0x90/0xb0
[<ffffff8008463950>] check_preemption_disabled+0x100/0x108
[<ffffff8008463998>] __this_cpu_preempt_check+0x18/0x20
[<ffffff80084c9194>] sysrq_handle_showregs+0x1c/0x40
[<ffffff80084c9c7c>] __handle_sysrq+0x12c/0x1a0
[<ffffff80084ca140>] write_sysrq_trigger+0x60/0x70
[<ffffff8008251e00>] proc_reg_write+0x90/0xd0
[<ffffff80081f1788>] __vfs_write+0x48/0x90
[<ffffff80081f241c>] vfs_write+0xa4/0x190
[<ffffff80081f3354>] SyS_write+0x54/0xb0
[<ffffff80080833f0>] el0_svc_naked+0x24/0x28
This can be seen on a common board like an r-pi3.
This happens because when echo p >/proc/sysrq-trigger,
get_irq_regs() is called outside of IRQ context,
if preemption is enabled in this situation,kernel will
print the call trace. Since many prior discussions on
the mailing lists have made it clear that get_irq_regs
either just returns NULL or stale data when used outside
of IRQ context,we simply avoid calling it outside of
IRQ context.
Signed-off-by: Jibin Xu <jibin.xu@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It has been reported that some platforms (odroid-c2) may require
a different tx phase setting to operate at high speed (hs200 and hs400)
To improve the situation, this patch includes tx phase in the tuning
process.
Fixes: d341ca88eead ("mmc: meson-gx: rework tuning function")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Resetting the phase when POWER_ON is set the set_ios() call means that the
phase is reset almost every time the set_ios() is called, while the
expected behavior was to reset the phase on a power cycle.
This had gone unnoticed until now because in all mode (except hs400) the
tuning is done after the last to set_ios(). In such case, the tuning
result is used anyway. In HS400, there are a few calls to set_ios() after
the tuning is done, overwriting the tuning result.
Resetting the phase on POWER_UP instead of POWER_ON solve the problem.
Fixes: d341ca88eead ("mmc: meson-gx: rework tuning function")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Using CLK_DIVIDER_ROUND_CLOSEST is unsafe as the mmc clock could be
rounded to a rate higher the specified rate. Removing this flag ensure
that, if the rate needs to be rounded, it will be rounded down.
Fixes: 51c5d8447bd7 ("MMC: meson: initial support for GX platforms")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.
I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.
The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.
Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.
We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.
The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.
What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)
Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb81647 ("[ARM] 5369/1: omap mmc: Add new
omap hsmmc controller for 2430 and 34xx, v3")
This optimization was removed in
commit 0ccd76d4c236 ("omap_hsmmc: Implement scatter-gather
emulation")
which found that scatter-gather emulation provided even
better performance.
The same was introduced for SDHCI in
commit 2134a922c6e7 ("sdhci: scatter-gather (ADMA) support")
I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Atmel USART, Freescale UARTs and OMAP UART all support the rs485 binding
described in rs485.txt, this commit just makes that explicit.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16. If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.
However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation. This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a port has no dma channel defined in the device tree, then
don't attempt to allocate a dma channel for the port.
Also suppress the warning message concerning the failure to allocate
a dma channel. Continue to emit the warning message if a dma
channel is defined but cannot be allocated.
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.
While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove
* pdev from mxser_initbrd
* old_termios from mxser_change_speed
as they are unused and update the callers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
move to arch_initcall to get the console up really early, it is
quite helpful for spotting early boot problems.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch remove the extra compatibility string "st,stm32-usart" from
driver & device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes the extra compatibility string "st,stm32-usart" to
avoid confusion, save some time & space.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
security_inode_getsecurity() provides the text string value
of a security attribute. It does not provide a "secctx".
The code in xattr_getsecurity() that calls security_inode_getsecurity()
and then calls security_release_secctx() happened to work because
SElinux and Smack treat the attribute and the secctx the same way.
It fails for cap_inode_getsecurity(), because that module has no
secctx that ever needs releasing. It turns out that Smack is the
one that's doing things wrong by not allocating memory when instructed
to do so by the "alloc" parameter.
The fix is simple enough. Change the security_release_secctx() to
kfree() because it isn't a secctx being returned by
security_inode_getsecurity(). Change Smack to allocate the string when
told to do so.
Note: this also fixes memory leaks for LSMs which implement
inode_getsecurity but not release_secctx, such as capabilities.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
If we got two AIO writes into a COW area the second one might not have any
COW extents left to convert. Handle that case gracefully instead of
triggering an assert or accessing beyond the bounds of the extent list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Since the CoW fork exists as a secondary data structure to the data
fork, we must always swap cow forks during swapext. We also need to
swap the extent counts and reset the cowblocks tags.
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Add temporary fix to HSDK platform code to setup CPU frequency
to 1GHz on early boot.
We can remove this fix when smart hsdk pll driver will be
introduced, see discussion:
https://www.mail-archive.com/linux-snps-arc@lists.infradead.org/msg02689.html
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Reported-by: Dmitrii Kolesnichenko <dmitrii@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARCv2 ISA_CONFIG and ARC700_BUILD build config registers are not
compatible. cpuinfo_arc had isa info placeholder which was mashup of bits
form both.
Untangle this by defining it off of ARCv2 ISA info and it is fine even
for ARC700 since former is a super set of latter (ARC700 buildonly has 2
bits for atomics and stack check).
At runtime, we treat ARCv2 ISA info as a generic placeholder but
populate it correctly depending on ARC700 or HS.
This paves way for adding more HS specific bits in isa info which was
colliding with the extra bits for arc700.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The top-level Makefile sets the default of UTS_MACHINE to $(ARCH).
If ARCH and UTS_MACHINE match, arch/$(ARCH)/Makefile need not specify
UTS_MACHINE explicitly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
With corresponding clk driver now merged upstream, switch to it.
- core_clk now represent the PLL (vs. fixed clk before)
- input_clk represent the clk signal src for PLL (basically xtal)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Commit 92e5aae45778 "kernel/watchdog: split up config options"
introduced SOFTLOCKUP_DETECTOR which selects LOCKUP_DETECTOR
instead of the latter to be selected itself.
We need to adjust our defconfigs accordingly.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
DW sdio controller has external ciu clock divider controlled
via register in SDIO IP. It divides sdio_ref_clk
(which comes from CGU) by 16 for default. So default mmcclk
clock (which comes to sdk_in) is 25000000 Hz.
So fix wrong current value (50000000 Hz) to actual 25000000 Hz.
Note this is a preventive fix, in line with similar change for HSDK
where this was actually needed. see:
http://lists.infradead.org/pipermail/linux-snps-arc/2017-September/002924.html
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
DW sdio controller has external ciu clock divider controlled via
register in SDIO IP. Due to its unexpected default value
(it should divide by 1 but it divides by 8)
SDIO IP uses wrong ciu clock and works unstable
So add temporary fix and change clock frequency from 100000000
to 12500000 Hz until we fix dw sdio driver itself.
Fixes SNPS STAR 9001204800
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
DW ethernet controller on AXS10x hangs sometimes after SW reset, so
add temporary quirk to reset DW ethernet controller IP core.
This quirk can be removed after axs10x reset driver
(see http://patchwork.ozlabs.org/patch/800273/)
or simple reset driver
(see https://patchwork.kernel.org/patch/9903375/)
will be available in upstream.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.14-rc cycle
Few minor fixes for omaps, mostly just boot time warning fixes:
- Drop undocumented camera binding that got merged during the merge window by
accident as I applied before Sakari's comments
- Fix soft reset warning for dra7 kexec boot for gpio1 as the optional clocks
need to be enabled for reset
- Fix dra7 kexec boot clock rate for McASP as the rate is no longer the default
rate after kexec
- Fix omap3 pandora MMC warning during boot
- Add am33xx SPI alias like we have on other SoCs
- Remove node for non-existing CPSW EMAC Ethernet on am43xx-epos-evm
* tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Adding the operating points on rk3368 like they were did not end up well
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.
And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.
* tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.14 (part 1)
Update MAINTAINERS for the Macchiatobin board (Armada 8K based)
Fix AP806 system controller size on Armada 7K/8K
* tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu:
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
A fix for random ethernet mac address problem
on DA850 EVM.
* tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add serial and ethernet aliases
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Fixes for 4.14:
- three DT fixes for the newly introduced sama5d27_som1_ek board
- one treewide modification that didn't touch this new PM code: we
synchronize now to be coherent with the other ARM platforms
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
ARM: dts: at91: sama5d27_som1_ek: fix USB host vbus
ARM: dts: at91: sama5d27_som1_ek: fix typos
ARM: dts: at91: sama5d27_som1_ek: update pinmux/pinconf for LEDs and USB
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This updates the Gemini defconfig with drivers merged
for v4.13 or v4.14:
- ATA driver is merged
- DMA driver is merged
- RTC driver gets selected from default Kconfig
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
It is no longer possible to load this at runtime, so let's
change the few remaining users to have it built-in all
the time.
arch/arm/configs/zeus_defconfig:115:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/viper_defconfig:116:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/pxa_defconfig:474:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
Reported-by: kernelci.org bot <bot@kernelci.org>
Fixes: 6104c37094e7 ("fbcon: Make fbcon a built-time depency for fbdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Before commit 9c5d760b8d22 ("mm: split gfp_mask and mapping flags into
separate fields") the private_* fields of struct adrress_space were
grouped together and using "ditto" in comments describing the last
fields was correct.
With introduction of gpf_mask between private_lock and private_list
"ditto" references the wrong description.
Fix it by using the elaborate description.
Link: http://lkml.kernel.org/r/1507009987-8746-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently running checkpatch on a directory with a cover-letter.patch
file reports the following error:
-----------------------------------------
patches/smp-v2/v2-0000-cover-letter.patch
-----------------------------------------
ERROR: Does not appear to be a unified-diff format patch
The logic to suppress the unified-diff check for cover letters is there
but is checking $file instead of $filename. Fix the variable to use the
correct one.
Link: http://lkml.kernel.org/r/20170909090406.31523-1-shorne@gmail.com
Signed-off-by: Stafford Horne <shorne@gmail.com>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
