| Age | Commit message (Collapse) | Author |
|---|
|
The AP has third pulse generator available starting with IPA v5.0.
Redefine ipa_qtime_val() to support that possibility. Pass the IPA
pointer as an argument so the version can be determined. And stop
using the sign of the returned tick count to indicate which of two
pulse generators to use.
Instead, have the caller provide the address of a variable that will
hold the selected pulse generator for the Qtime value. And for
version 5.0, check whether the third pulse generator best represents
the time period.
Add code in ipa_qtime_config() to configure the fourth pulse
generator for IPA v5.0+; in that case configure both the third and
fourth pulse generators to use 10 msec granularity.
Consistently use "ticks" for local variables that represent a tick
count.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with IPA v5.0, the head-of-line blocking timer has more
than two pulse generators available to define timer granularity.
To prepare for that, change the way the field value is encoded
to use ipa_reg_encode() rather than ipa_reg_bit().
The aggregation granularity selection could (in principle) also use
an additional pulse generator starting with IPA v5.0. Encode the
AGGR_GRAN_SEL field differently to allow that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v5.0+ separates the configuration of entries in the cached
(previously "hashed") routing and filtering tables into distinct
registers. Previously a single "filter and router" register updated
entries in both tables at once; now the routing and filter table
caches have separate registers that define their content.
This patch updates the code that zeroes entries in the cached filter
and router tables to support IPA versions including v5.0+.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the code that causes filter and router table caches to be
flushed so that it supports IPA versions 5.0+. It adds a comment in
ipa_hardware_config_hashing() that explains that cacheing does not
need to be enabled, just as before, because it's enabled by default.
(For the record, the FILT_ROUT_CACHE_CFG register would have been
used if we wanted to explicitly enable these.)
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define some new registers that appear starting with IPA v5.0, along
with enumerated types identifying their fields. Code that uses
these will be added by upcoming patches.
Most of the new registers are related to filter and routing tables,
and in particular, their "hashed" variant. These tables are better
described as "cached", where a hash value determines which entries
are cached. From now on, naming related to this functionality will
use "cache" instead of "hash", and that is reflected in these new
register names. Some registers for managing these caches and their
contents have changed as well.
A few other new field definitions for registers (unrelated to table
caches) are also defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IP_PACKET_INIT immediate command defines the destination
endpoint to which a packet should be sent. Prior to IPA v5.0, a
5 bit field in that command represents the endpoint, but starting
with IPA v5.0, the field is extended to 8 bits to support more than
32 endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Increase the number of endpoints supported by the driver to 36,
which IPA v5.0 supports. This makes it impossible to check at build
time whether the supported number is too big to fit within the
(5-bit) PACKET_INIT destination endpoint field. Instead, convert
the build time check to compare against what fits in 8 bits.
Add a check in ipa_endpoint_config() to also ensure the hardware
reports an endpoint count that's in the expected range. Just
open-code 32 as the limit (the PACKET_INIT field mask is not
available where we'd want to use it).
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-01-30
Add fast update encryption key
Jianbo Liu Says:
================
Data encryption keys (DEKs) are the keys used for data encryption and
decryption operations. Starting from version 22.33.0783, firmware is
optimized to accelerate the update of user keys into DEK object in
hardware. The support for bulk allocation and destruction of DEK
objects is added, and the bulk allocated DEKs are uninitialized, as
the bulk creation requires no input key. When offload
encryption/decryption, user gets one object from a bulk, and updates
key by a new "modify DEK" command. This command is the same as create
DEK object, but requires no heavy context memory allocation in
firmware, which consumes most cpu cycles of the create DEK command.
DEKs are cached internally by the NIC, so invalidating internal NIC
caches is required before reusing DEKs. The SYNC_CRYPTO command is
added to support it. DEK object can be reused, the keys in it can be
updated after this command is executed.
This patchset enhances the key creation and destruction flow, to get
use of this new feature. Any user, for example, ktls, ipsec and
macsec, can use it to offload keys. But, only ktls uses it, as others
don't need many keys, and caching two many DEKs in pool is wasteful.
There are two new data struts added:
a. DEK pool. One pool is created for each key type. The bulks by
the type, are placed in the pool's different bulk lists, according to
the number of available and in_used DEKs in the bulk.
b. DEK bulk. All DEKs in one bulk allocation are store here. There
are two bitmaps to indicate the state of each DEK.
New APIs are then added. When user need a DEK object,
a. Fetch one bulk with avail DEKs, from the partial_list or
avail_list, otherwise create new one.
b. Pick one DEK, and set its need_sync and in_used bits to 1.
Move the bulk to full_list if no more available keys, or put it to
partial_list if the bulk is newly created.
c. Update DEK object's key with user key, by the "modify DEK"
command.
d. Return DEK struct to user, then it gets the object id and fills
it into the offload commands.
When user free a DEK,
a. Set in_use bit to 0. If all need_sync bits are 1 and all in_use
bits of this bulk are 0, move it to sync_list.
b. If the number of DEKs, which are freed by users, is over the
threshold (128), schedule a workqueue to do the sync process.
For the sync process, the SYNC_CRYPTO command is executed first. Then,
for each bulks in partial_list, full_list and sync_list, reset
need_sync bits of the freed DEK objects. If all need_sync bits in one
bulk are zero, move it to avail_list.
We already supported TIS pool to recycle the TISes. With this series
and TIS pool, TLS CPS performance is improved greatly.
And we tested https on the system:
CPU: dual AMD EPYC 7763 64-Core processors
RAM: 512G
DEV: ConnectX-6 DX, with FW ver 22.33.0838 and TLS_OPTIMISE=true
TLS CPS performance numbers are:
Before: 11k connections/sec
After: 101 connections/sec
================
* tag 'mlx5-updates-2023-01-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: kTLS, Improve connection rate by using fast update encryption key
net/mlx5: Keep only one bulk of full available DEKs
net/mlx5: Add async garbage collector for DEK bulk
net/mlx5: Reuse DEKs after executing SYNC_CRYPTO command
net/mlx5: Use bulk allocation for fast update encryption key
net/mlx5: Add bulk allocation and modify_dek operation
net/mlx5: Add support SYNC_CRYPTO command
net/mlx5: Add new APIs for fast update encryption key
net/mlx5: Refactor the encryption key creation
net/mlx5: Add const to the key pointer of encryption key creation
net/mlx5: Prepare for fast crypto key update if hardware supports it
net/mlx5: Change key type to key purpose
net/mlx5: Add IFC bits and enums for crypto key
net/mlx5: Add IFC bits for general obj create param
net/mlx5: Header file for crypto
====================
Link: https://lore.kernel.org/r/20230131031201.35336-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Release bridge info once packet escapes the br_netfilter path,
from Florian Westphal.
2) Revert incorrect fix for the SCTP connection tracking chunk
iterator, also from Florian.
First path fixes a long standing issue, the second path addresses
a mistake in the previous pull request for net.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
Revert "netfilter: conntrack: fix bug in for_each_sctp_chunk"
netfilter: br_netfilter: disable sabotage_in hook after first suppression
====================
Link: https://lore.kernel.org/r/20230131133158.4052-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Meson G12A Internal PHY does not support standard IEEE MMD extended
register access, therefore add generic dummy stubs to fail the read and
write MMD calls. This is necessary to prevent the core PHY code from
erroneously believing that EEE is supported by this PHY even though this
PHY does not support EEE, as MMD register access returns all FFFFs.
Fixes: 5c3407abb338 ("net: phy: meson-gxl: add g12a support")
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230130231402.471493-1-cphealy@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
introduced UDP listifyed GRO. The segmentation relies on frag_list being
untouched when passing through the network stack. This assumption can be
broken sometimes, where frag_list itself gets pulled into linear area,
leaving frag_list being NULL. When this happens it can trigger
following NULL pointer dereference, and panic the kernel. Reverse the
test condition should fix it.
[19185.577801][ C1] BUG: kernel NULL pointer dereference, address:
...
[19185.663775][ C1] RIP: 0010:skb_segment_list+0x1cc/0x390
...
[19185.834644][ C1] Call Trace:
[19185.841730][ C1] <TASK>
[19185.848563][ C1] __udp_gso_segment+0x33e/0x510
[19185.857370][ C1] inet_gso_segment+0x15b/0x3e0
[19185.866059][ C1] skb_mac_gso_segment+0x97/0x110
[19185.874939][ C1] __skb_gso_segment+0xb2/0x160
[19185.883646][ C1] udp_queue_rcv_skb+0xc3/0x1d0
[19185.892319][ C1] udp_unicast_rcv_skb+0x75/0x90
[19185.900979][ C1] ip_protocol_deliver_rcu+0xd2/0x200
[19185.910003][ C1] ip_local_deliver_finish+0x44/0x60
[19185.918757][ C1] __netif_receive_skb_one_core+0x8b/0xa0
[19185.927834][ C1] process_backlog+0x88/0x130
[19185.935840][ C1] __napi_poll+0x27/0x150
[19185.943447][ C1] net_rx_action+0x27e/0x5f0
[19185.951331][ C1] ? mlx5_cq_tasklet_cb+0x70/0x160 [mlx5_core]
[19185.960848][ C1] __do_softirq+0xbc/0x25d
[19185.968607][ C1] irq_exit_rcu+0x83/0xb0
[19185.976247][ C1] common_interrupt+0x43/0xa0
[19185.984235][ C1] asm_common_interrupt+0x22/0x40
...
[19186.094106][ C1] </TASK>
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/Y9gt5EUizK1UImEP@debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When memory allocation fails in lynx_pcs_create() and it returns NULL,
there remains a dangling reference to the mdiodev returned by
of_mdio_find_device() which is leaked as soon as memac_pcs_create()
returns empty-handed.
Fixes: a7c2a32e7f22 ("net: fman: memac: Use lynx pcs driver")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://lore.kernel.org/r/20230130193051.563315-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN: Remove redundant Device Control Error Reporting Enable
Bjorn Helgaas says:
Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is native"),
the PCI core sets the Device Control bits that enable error reporting for
PCIe devices.
This series removes redundant calls to pci_enable_pcie_error_reporting()
that do the same thing from several NIC drivers.
There are several more drivers where this should be removed; I started with
just the Intel drivers here.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbe: Remove redundant pci_enable_pcie_error_reporting()
igc: Remove redundant pci_enable_pcie_error_reporting()
igb: Remove redundant pci_enable_pcie_error_reporting()
ice: Remove redundant pci_enable_pcie_error_reporting()
iavf: Remove redundant pci_enable_pcie_error_reporting()
i40e: Remove redundant pci_enable_pcie_error_reporting()
fm10k: Remove redundant pci_enable_pcie_error_reporting()
e1000e: Remove redundant pci_enable_pcie_error_reporting()
====================
Link: https://lore.kernel.org/r/20230130192519.686446-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Petr Machata says:
====================
selftests: mlxsw: Convert to iproute2 dcb
There is a dedicated tool for configuration of DCB in iproute2. Use it
in the selftests instead of lldpad.
Patches #1-#3 convert three tests. Patch #4 drops the now-unnecessary
lldpad helpers.
====================
Link: https://lore.kernel.org/r/cover.1675096231.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The existing users of these helpers have been converted to iproute2 dcb.
Drop the helpers.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set up default port priority through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set up DSCP prioritization through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set up DSCP prioritization through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It tries to avoid the frequently hb_timer refresh in commit ba6f5e33bdbb
("sctp: avoid refreshing heartbeat timer too often"), and it only allows
mod_timer when the new expires is after hb_timer.expires. It means even
a much shorter interval for hb timer gets applied, it will have to wait
until the current hb timer to time out.
In sctp_do_8_2_transport_strike(), when a transport enters PF state, it
expects to update the hb timer to resend a heartbeat every rto after
calling sctp_transport_reset_hb_timer(), which will not work as the
change mentioned above.
The frequently hb_timer refresh was caused by sctp_transport_reset_timers()
called in sctp_outq_flush() and it was already removed in the commit above.
So we don't have to check hb_timer.expires when resetting hb_timer as it is
now not called very often.
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/d958c06985713ec84049a2d5664879802710179a.1675095933.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jerome Brunet says:
====================
net: mdio: add amlogic gxl mdio mux support
Add support for the MDIO multiplexer found in the Amlogic GXL SoC family.
This multiplexer allows to choose between the external (SoC pins) MDIO bus,
or the internal one leading to the integrated 10/100M PHY.
This multiplexer has been handled with the mdio-mux-mmioreg generic driver
so far. When it was added, it was thought the logic was handled by a
single register.
It turns out more than a single register need to be properly set.
As long as the device is using the Amlogic vendor bootloader, or upstream
u-boot with net support, it is working fine since the kernel is inheriting
the bootloader settings. Without net support in the bootloader, this glue
comes unset in the kernel and only the external path may operate properly.
With this driver (and the associated change in
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi), the kernel no longer relies
on the bootloader to set things up, fixing the problem.
====================
Link: https://lore.kernel.org/r/20230130151616.375168-1-jbrunet@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the mdio mux and internal phy glue of the GXL SoC
family
Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add documentation for the MDIO bus multiplexer found on the Amlogic GXL
SoC family
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jakub Kicinski says:
====================
tools: ynl: more docs and basic ethtool support
I got discouraged from supporting ethtool in specs, because
generating the user space C code seems a little tricky.
The messages are ID'ed in a "directional" way (to and from
kernel are separate ID "spaces"). There is value, however,
in having the spec and being able to for example use it
in Python.
After paying off some technical debt - add a partial
ethtool spec. Partial because the header for ethtool is almost
a 1000 LoC, so converting in one sitting is tough. But adding
new commands should be trivial now.
Last but not least I add more docs, I realized that I've been
sending a similar "instructions" email to people working on
new families. It's now intro-specs.rst.
====================
Link: https://lore.kernel.org/r/20230131023354.1732677-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The scripts require Python 3 and some distros are dropping
Python 2 support.
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a bit of documentation about the internals of Netlink
and the specs, but really the goal is for most people to not
worry about those. Add a practical guide for beginners who
want to poke at the specs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethtool is one of the most actively developed families.
With the changes to the CLI it should be possible to use
the YNL based code for easy prototyping and development.
Add a partial family definition. I've tested the string
set and rings. I don't have any MAC Merge implementation
to test with, but I added the definition for it, anyway,
because it's last. New commands can simply be added at
the end without having to worry about manually providing
IDs / values.
Set (with notification support - None is the response,
the data is from the notification):
$ sudo ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/ethtool.yaml \
--do rings-set \
--json '{"header":{"dev-name":"enp0s31f6"}, "rx":129}' \
--subscribe monitor
None
[{'msg': {'header': {'dev-index': 2, 'dev-name': 'enp0s31f6'},
'rx': 136,
'rx-max': 4096,
'tx': 256,
'tx-max': 4096,
'tx-push': 0},
'name': 'rings-ntf'}]
Do / dump (yes, the kernel requires that even for dump and even
if empty - the "header" nest must be there):
$ ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/ethtool.yaml \
--do rings-get \
--json '{"header":{"dev-index": 2}}'
{'header': {'dev-index': 2, 'dev-name': 'enp0s31f6'},
'rx': 136,
'rx-max': 4096,
'tx': 256,
'tx-max': 4096,
'tx-push': 0}
$ ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/ethtool.yaml \
--dump rings-get \
--json '{"header":{}}'
[{'header': {'dev-index': 2, 'dev-name': 'enp0s31f6'},
'rx': 136,
'rx-max': 4096,
'tx': 256,
'tx-max': 4096,
'tx-push': 0},
{'header': {'dev-index': 3, 'dev-name': 'wlp0s20f3'}, 'tx-push': 0},
{'header': {'dev-index': 19, 'dev-name': 'enp58s0u1u1'},
'rx': 100,
'rx-max': 4096,
'tx-push': 0}]
And error reporting:
$ ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/ethtool.yaml \
--dump rings-get \
--json '{"header":{"flags":5}}'
Netlink error: Invalid argument
nl_len = 68 (52) nl_flags = 0x300 nl_type = 2
error: -22 extack: {'msg': 'reserved bit set',
'bad-attr-offs': 24,
'bad-attr': '.header.flags'}
None
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I had a (bright?) idea of introducing the concept of enum-models
to account for all the weird ways families enumerate their messages.
I've never finished it because generating C code for each of them
is pretty daunting. But for languages which can use ID values directly
the support is simple enough, so clean this up a bit.
"unified" model is what I recommend going forward.
"directional" model is what ethtool uses.
"notify-split" is used by the proposed DPLL code, but we can just
make them use "unified", it hasn't been merged :)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CLI script tries to validate jsonschema by default.
It's seems better to validate too many times than too few.
However, when copying the scripts to random servers having
to install jsonschema is tedious. Load jsonschema via
importlib, and let the user opt out.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When I wrote the first version of the Python code I was quite
excited that we can generate class methods directly from the
spec. Unfortunately we need to use valid identifiers for method
names (specifically no dashes are allowed). Don't reuse those
names on the CLI, it's much more natural to use the operation
names exactly as listed in the spec.
Instead of:
./cli --do rings_get
use:
./cli --do rings-get
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One of my favorite features of the Netlink specs is that they
make decoding structured extack a ton easier.
Implement pretty printing bad attribute names in YNL.
For example it will now say:
'bad-attr': '.header.flags'
rather than the useless:
'bad-attr-offs': 32
Proof:
$ ./cli.py --spec ethtool.yaml --do rings_get \
--json '{"header":{"dev-index":1, "flags":4}}'
Netlink error: Invalid argument
nl_len = 68 (52) nl_flags = 0x300 nl_type = 2
error: -22 extack: {'msg': 'reserved bit set',
'bad-attr': '.header.flags'}
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethtool uses mutli-attr, add the support to YNL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support families which use different IDs for messages
to and from the kernel.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethtool needs support for handful of extra types.
It doesn't have the definitions section yet.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adapt the common object hierarchy in code gen and CLI.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There's a lot of copy and pasting going on between the "cli"
and code gen when it comes to representing the parsed spec.
Create a library which both can use.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the CLI code out of samples/ and the library part
of it into tools/net/ynl/lib/. This way we can start
sharing some code with the code gen.
Initially I thought that code gen is too C-specific to
share anything but basic stuff like calculating values
for enums can easily be shared.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An earlier fix tried to address generated code jumping around
one code-gen run to another. Turns out dict()s are already
ordered since Python 3.7, the problem is that we iterate over
operation modes using a set(). Sets are unordered in Python.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"cpuset has a bug which can cause an oops after some configuration
operations, introduced during the v6.1 cycle.
This single commit fixes the bug"
* tag 'cgroup-for-6.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Fix wrong check in update_parent_subparts_cpumask()
|
|
It was found that the check to see if a partition could use up all
the cpus from the parent cpuset in update_parent_subparts_cpumask()
was incorrect. As a result, it is possible to leave parent with no
effective cpu left even if there are tasks in the parent cpuset. This
can lead to system panic as reported in [1].
Fix this probem by updating the check to fail the enabling the partition
if parent's effective_cpus is a subset of the child's cpus_allowed.
Also record the error code when an error happens in update_prstate()
and add a test case where parent partition and child have the same cpu
list and parent has task. Enabling partition in the child will fail in
this case.
[1] https://www.spinics.net/lists/cgroups/msg36254.html
Fixes: f0af1bfc27b5 ("cgroup/cpuset: Relax constraints to partition & cpus changes")
Cc: stable@vger.kernel.org # v6.1
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core fixes.
One simply moves an annotation from put to release to avoid the
warning triggering needlessly in alua, but to keep it in case release
is ever called from that path (which we don't think will happen).
The other reverts a change to the PQ=1 target scanning behaviour
that's under intense discussion at the moment"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Revert "scsi: core: map PQ=1, PDT=other values to SCSI_SCAN_TARGET_PRESENT"
scsi: core: Fix the scsi_device_put() might_sleep annotation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A couple of v4l2 core fixes:
- fix a regression on strings control support
- fix a regression for some drivers that depend on an odd streaming
behavior"
* tag 'media/v6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videobuf2: set q->streaming later
media: v4l2-ctrls-api.c: move ctrl->is_new = 1 to the correct line
|
|
Historically calls to __decompress() didn't specify "out_len" parameter
on many architectures including s390, expecting that no writes beyond
uncompressed kernel image are performed. This has changed since commit
2aa14b1ab2c4 ("zstd: import usptream v1.5.2") which includes zstd library
commit 6a7ede3dfccb ("Reduce size of dctx by reutilizing dst buffer
(#2751)"). Now zstd decompression code might store literal buffer in
the unwritten portion of the destination buffer. Since "out_len" is
not set, it is considered to be unlimited and hence free to use for
optimization needs. On s390 this might corrupt initrd or ipl report
which are often placed right after the decompressor buffer. Luckily the
size of uncompressed kernel image is already known to the decompressor,
so to avoid the problem simply specify it in the "out_len" parameter.
Link: https://github.com/facebook/zstd/commit/6a7ede3dfccb
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/patch-1.thread-41c676.git-41c676c2d153.your-ad-here.call-01675030179-ext-9637@work.hours
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Now that the bundle->channel_lock has been eliminated, we don't need the
dummy service bundle anymore. It's purpose was purely to provide the
channel_lock for service connections.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Change the rx_packet tracepoint to display the securityIndex from the
packet header instead of displaying the type in numeric form. There's no
need for the latter, as the display of the type in symbolic form will fall
back automatically to displaying the hex value if no symbol is available.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Set a reason when freeing a packet that has been consumed such that
dropwatch doesn't complain that it has been dropped.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
We no longer need local->defrag_sem as all DATA packet transmission is now
done from one thread, so remove it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
call->tx_buffer is now only accessed within the I/O thread (->tx_sendmsg is
the way sendmsg passes packets to the I/O thread) so there's no need to
lock around it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Now that general ACK transmission is done from the same thread as incoming
DATA packet wrangling, there's no possibility that the SACK table will be
being updated by the latter whilst the former is trying to copy it to an
ACK.
This means that we can safely rotate the SACK table whilst updating it
without having to take a lock, rather than keeping all the bits inside it
in fixed place and copying and then rotating it in the transmitter.
Therefore, simplify SACK handing by keeping track of starting point in the
ring and rotate slots down as we consume them.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
call->ackr_window doesn't need to be atomic as ACK generation and ACK
transmission are now done in the same thread, so drop the atomic64 handling
and split it into two separate members.
Similarly, call->ackr_nr_unacked doesn't need to be atomic now either.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
When doing a call that has a single transmitted data packet and a massive
amount of received data packets, we only ping for one RTT sample, which
means we don't get a good reading on it.
Fix this by converting occasional IDLE ACKs into PING ACKs to elicit a
response.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
