| Age | Commit message (Collapse) | Author |
|---|
|
The current code causes problems when the unregistering netdevice could
be different then the registering one.
Since the check in mlx5_lag_netdev_event() does not allow any other
network namespace anyway, fix this by registerting the lag notifier
per init network namespace only.
Fixes: d48834f9d4b4 ("mlx5: Use dev_net netdevice notifier registrations")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Aya Levin <ayal@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Julian Wiedmann says:
====================
s390/qeth: updates 2020-02-27
please apply the following patch series for qeth to netdev's net-next
tree.
This adds support for ETHTOOL_RX_COPYBREAK, along with small cleanups
and fine-tuning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the ethtool hooks for the ETHTOOL_RX_COPYBREAK tunable.
The copybreak is stored into netdev_priv, so that we automatically go
back to the default value if the netdev is re-allocated.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trust the napi_disable() in qeth_stop() to handle this.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once the IDX connection is down, there's no point in trying to issue
more IOs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This let's us start every new IDX connection with clean seqnos.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like these were never used, ever since the driver was initially
added.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's good practice to not blindly trust what the HW offers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly define the cmd's struct to get rid of some casts and accesses
at magic offsets.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
card->info.unique_id is always 0 for IQD devices, so don't bother with
copying it into the 0-initialized cmd.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID subsystem fixes from Jiri Kosina:
- syzkaller-reported error handling fixes in various drivers, from
various people
- increase of HID report buffer size to 8K, which is apparently needed
by certain modern devices
- a few new device-ID-specific fixes / quirks
- battery charging status reporting fix in logitech-hidpp, from Filipe
Laíns
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: hid-bigbenff: fix race condition for scheduled work during removal
HID: hid-bigbenff: call hid_hw_stop() in case of error
HID: hid-bigbenff: fix general protection fault caused by double kfree
HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override
HID: alps: Fix an error handling path in 'alps_input_configured()'
HID: hiddev: Fix race in in hiddev_disconnect()
HID: core: increase HID report buffer size to 8KiB
HID: core: fix off-by-one memset in hid_report_raw_event()
HID: apple: Add support for recent firmware on Magic Keyboards
HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock
HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active
|
|
Follow the pattern used with other *_show_fdinfo functions and only
define unix_show_fdinfo and set it in proto_ops if CONFIG_PROCFS
is set.
Fixes: 3c32da19a858 ("unix: Show number of pending scm files of receive queue in fdinfo")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
selftests: updates for mlxsw driver test
This patchset contains tweaks to the existing tests and is also adding
couple of new ones, namely tests for shared buffer and red offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the test inserts X /32 routes and for each route it is
testing that a packet sent from the first host is received by the second
host, which is very time-consuming.
Instead only validate the offload flag of each route and get the same result.
Wait between the creation of the routes and the offload validation in
order to make sure that all the routes were successfully offloaded.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After adding a given number of flower rules for different IPv6
addresses, the test generates traffic and ensures that each packet is
received, which is time-consuming.
Instead, test the offload indication of the tc flower rules and reduce
the running time by half.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test the max shared buffer occupancy for port's pool and port's TC's (using
different types of packets).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mlxsw lib for common defines, helpers etc.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two devlink port helpers:
* devlink port get by netdev
* devlink cpu port get
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sanity check for devlink info command.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test physical ports' shared buffer configuration options using random
values related to a specific configuration option. There are 3
configuration options: pool, TC bind and portpool.
Each sub-test, test a different configuration option and random the related
values as the follow:
* For pools, pool's size will be randomized.
* For TC bind, pool number and threshold will be randomized.
* For portpools, threshold will be randomized.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rtnetlink test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vxlan test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Blackhole routes test uses offload indication checks.
Use busywait helper and wait until the routes offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test checks that packets are trapped when they should egress a
router interface (RIF) that has become disabled. This is a temporary
state in a RIF's deletion sequence.
Currently, the test deletes the RIF by flushing all the IP addresses
configured on the associated netdev (br0). However, this is racy, as
this also flushes all the routes pointing to the netdev and if the
routes are deleted from the device before the RIF is disabled, then no
packets will try to egress the disabled RIF and the trap will not be
triggered.
Instead, trigger the deletion of the RIF by unlinking the mlxsw port
from the bridge that is backing the RIF. Unlike before, this will not
cause the kernel to delete the routes pointing to the bridge.
Note that due to current mlxsw locking scheme the RIF is always deleted
first, but this is going to change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Include test of forbidding to have multiple mirror actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Include test of forbidding to have redirect rule on egress-bound block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This tests that below the queue minimum length, there is no dropping /
marking, and above max, everything is dropped / marked.
The test is structured as a core file with topology and test code, and
three wrappers: one for RED used as a root Qdisc, and two for
testing (W)RED under PRIO and ETS.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract a helper __start_traffic() configurable by protocol type. Allow
passing through extra mausezahn arguments. Add a wrapper,
start_tcp_traffic().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Luo bin says:
====================
hinic: BugFixes
the bug fixed in patch #2 has been present since the first commit.
the bugs fixed in patch #1 and patch #3 have been present since the
following commits:
patch #1: 352f58b0d9f2 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
patch #3: 421e9526288b ("hinic: add rss support")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
should use real receive queue number to configure hw rss
indirect table rather than maximal queue number
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a reserved field is used to signify prime physical function index
in the latest firmware version, so we must assign a value to it
correctly
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
can not use a local variable as an input parameter of
irq_set_affinity_hint
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull documentation fixes from Jonathan Corbet:
"A pair of docs-build fixes"
* tag 'docs-5.6-fixes' of git://git.lwn.net/linux:
docs: Fix empty parallelism argument
docs: remove MPX from the x86 toc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two fixes for problems found by syzbot:
- Moving audit filter structure fields into a union caused some
problems in the code which populates that filter structure.
We keep the union (that idea is a good one), but we are fixing the
code so that it doesn't needlessly set fields in the union and mess
up the error handling.
- The audit_receive_msg() function wasn't validating user input as
well as it should in all cases, we add the necessary checks"
* tag 'audit-pr-20200226' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: always check the netlink payload length in audit_receive_msg()
audit: fix error handling in audit_data_to_entry()
|
|
Russell King says:
====================
VLANs, DSA switches and multiple bridges
This is a repost of the previously posted RFC back in December, which
did not get fully reviewed. I've dropped the RFC tag this time as no
one really found anything too problematical in the RFC posting.
I've been trying to configure DSA for VLANs and not having much success.
The setup is quite simple:
- The main network is untagged
- The wifi network is a vlan tagged with id $VN running over the main
network.
I have an Armada 388 Clearfog with a PCIe wifi card which I'm trying to
setup to provide wifi access to the vlan $VN network, while the switch
is also part of the main network.
However, I'm encountering problems:
1) vlan support in DSA has a different behaviour from the Linux
software bridge implementation.
# bridge vlan
port vlan ids
lan1 1 PVID Egress Untagged
...
shows the default setup - the bridge ports are all configured for
vlan 1, untagged egress, and vlan 1 as the port vid. Issuing:
# ip li set dev br0 type bridge vlan_filtering 1
with no other vlan configuration commands on a Linux software bridge
continues to allow untagged traffic to flow across the bridge.
This difference in behaviour is because the MV88E6xxx VTU is
completely empty - because net/dsa ignores all vlan settings for
a port if br_vlan_enabled(dp->bridge_dev) is false - this reflects
the vlan filtering state of the bridge, not whether the bridge is
vlan aware.
What this means is that attempting to configure the bridge port
vlans before enabling vlan filtering works for Linux software
bridges, but fails for DSA bridges.
2) Assuming the above is sorted, we move on to the next issue, which
is altogether more weird. Let's take a setup where we have a
DSA bridge with lan1..6 in a bridge device, br0, with vlan
filtering enabled. lan1 is the upstream port, lan2 is a downstream
port that also wants to see traffic on vlan id $VN.
Both lan1 and lan2 are configured for that:
# bridge vlan add vid $VN dev lan1
# bridge vlan add vid $VN dev lan2
# ip li set br0 type bridge vlan_filtering 1
Untagged traffic can now pass between all the six lan ports, and
vlan $VN between lan1 and lan2 only. The MV88E6xxx 8021q_mode
debugfs file shows all lan ports are in mode "secure" - this is
important! /sys/class/net/br0/bridge/vlan_filtering contains 1.
tcpdumping from another machine on lan4 shows that no $VN traffic
reaches it. Everything seems to be working correctly...
In order to further bridge vlan $VN traffic to hostapd's wifi
interface, things get a little more complex - we can't add hostapd's
wifi interface to br0 directly, because hostapd will bring up the
wifi interface and leak the main, untagged traffic onto the wifi.
(hostapd does have vlan support, but only as a dynamic per-client
thing, and there's no hooks I can see to allow script-based config
of the network setup before hostapd up's the wifi interface.)
So, what I tried was:
# ip li add link br0 name br0.$VN type vlan id $VN
# bridge vlan add vid $VN dev br0 self
# ip li set dev br0.$VN up
So far so good, we get a vlan interface on top of the bridge, and
tcpdumping it shows we get traffic. The 8021q_mode file has not
changed state. Everything still seems to be correct.
# bridge addbr br1
Still nothing has changed.
# bridge addif br1 br0.$VN
And now the 8021q_mode debugfs file shows that all ports are now in
"disabled" mode, but /sys/class/net/br0/bridge/vlan_filtering still
contains '1'. In other words, br0 still thinks vlan filtering is
enabled, but the hardware has had vlan filtering disabled.
Adding some stack traces to an appropriate point indicates that this
is because __switchdev_handle_port_attr_set() recurses down through
the tree of interfaces, skipping over the vlan interface, applying
br1's configuration to br0's ports.
This surely can not be right - surely
__switchdev_handle_port_attr_set() and similar should stop recursing
down through another master bridge device? There are probably other
network device classes that switchdev shouldn't recurse down too.
I've considered whether switchdev is the right level to do it, and
I think it is - as we want the check/set callbacks to be called for
the top level device even if it is a master bridge device, but we
don't want to recurse through a lower master bridge device.
v2: dropped patch 3, since that has an outstanding issue, and my
question on it has not been answered. Otherwise, these are the
same patches. Maybe we can move forward with just these two?
v3: include DSA ports in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports. If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.
Avoid this warning for CPU and DSA ports.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring a tree of independent bridges, propagating changes
from the upper bridge across a bridge master to the lower bridge
ports brings surprises.
For example, a lower bridge may have vlan filtering enabled. It
may have a vlan interface attached to the bridge master, which may
then be incorporated into another bridge. As soon as the lower
bridge vlan interface is attached to the upper bridge, the lower
bridge has vlan filtering disabled.
This occurs because switchdev recursively applies its changes to
all lower devices no matter what.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In smc_ib_remove_dev() check if the provided ib device was actually
initialized for SMC before.
Reported-by: syzbot+84484ccebdd4e5451d91@syzkaller.appspotmail.com
Fixes: a4cf0443c414 ("smc: introduce SMC as an IB-client")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes: 481a7d154cbb ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.
Fixes: a5afc1678044 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callers only expect NULL pointers, so returning an error pointer
will lead to an Oops.
Fixes: 0c2204a4ad71 ("net: qrtr: Migrate nameservice to kernel from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a missing shift for the media operation mode selection.
This does not fix the driver as the current operation mode (copper) has
a value of 0, but this wouldn't work for other modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot noted that the master MPTCP socket lacks the icsk_sync_mss
callback, and was able to trigger a null pointer dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 8e171067 P4D 8e171067 PUD 93fa2067 PMD 0
Oops: 0010 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 8984 Comm: syz-executor066 Not tainted 5.6.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:0x0
Code: Bad RIP value.
RSP: 0018:ffffc900020b7b80 EFLAGS: 00010246
RAX: 1ffff110124ba600 RBX: 0000000000000000 RCX: ffff88809fefa600
RDX: ffff8880994cdb18 RSI: 0000000000000000 RDI: ffff8880925d3140
RBP: ffffc900020b7bd8 R08: ffffffff870225be R09: fffffbfff140652a
R10: fffffbfff140652a R11: 0000000000000000 R12: ffff8880925d35d0
R13: ffff8880925d3140 R14: dffffc0000000000 R15: 1ffff110124ba6ba
FS: 0000000001a0b880(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 00000000a6d6f000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
cipso_v4_sock_setattr+0x34b/0x470 net/ipv4/cipso_ipv4.c:1888
netlbl_sock_setattr+0x2a7/0x310 net/netlabel/netlabel_kapi.c:989
smack_netlabel security/smack/smack_lsm.c:2425 [inline]
smack_inode_setsecurity+0x3da/0x4a0 security/smack/smack_lsm.c:2716
security_inode_setsecurity+0xb2/0x140 security/security.c:1364
__vfs_setxattr_noperm+0x16f/0x3e0 fs/xattr.c:197
vfs_setxattr fs/xattr.c:224 [inline]
setxattr+0x335/0x430 fs/xattr.c:451
__do_sys_fsetxattr fs/xattr.c:506 [inline]
__se_sys_fsetxattr+0x130/0x1b0 fs/xattr.c:495
__x64_sys_fsetxattr+0xbf/0xd0 fs/xattr.c:495
do_syscall_64+0xf7/0x1c0 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440199
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffcadc19e48 EFLAGS: 00000246 ORIG_RAX: 00000000000000be
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440199
RDX: 0000000020000200 RSI: 00000000200001c0 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 0000000000000003 R09: 00000000004002c8
R10: 0000000000000009 R11: 0000000000000246 R12: 0000000000401a20
R13: 0000000000401ab0 R14: 0000000000000000 R15: 0000000000000000
Modules linked in:
CR2: 0000000000000000
Address the issue adding a dummy icsk_sync_mss callback.
To properly sync the subflows mss and options list we need some
additional infrastructure, which will land to net-next.
Reported-by: syzbot+f4dfece964792d80b139@syzkaller.appspotmail.com
Fixes: 2303f994b3e1 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit we revert the part of
commit 1a63443afd70 ("net/amazon: Ensure that driver version is aligned to the linux kernel"),
which breaks the interface between the ENA driver and FW.
We also replace the use of DRIVER_VERSION with DRIVER_GENERATION
when we bring back the deleted constants that are used in interface with
ENA device FW.
This commit does not change the driver version reported to the user via
ethtool, which remains the kernel version.
Fixes: 1a63443afd70 ("net/amazon: Ensure that driver version is aligned to the linux kernel")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Westphal says:
====================
mptcp: update mptcp ack sequence outside of recv path
This series moves mptcp-level ack sequence update outside of the recvmsg path.
Current approach has two problems:
1. There is delay between arrival of new data and the time we can ack
this data.
2. If userspace doesn't call recv for some time, mptcp ack_seq is not
updated at all, even if this data is queued in the subflow socket
receive queue.
Move skbs from the subflow socket receive queue to the mptcp-level
receive queue, updating the mptcp-level ack sequence and have recv
take skbs from the mptcp-level receive queue.
The first place where we will attempt to update the mptcp level acks
is from the subflows' data_ready callback, even before we make userspace
aware of new data.
Because of possible deadlock (we need to take the mptcp socket lock
while already holding the subflow sockets lock), we may still need to
defer the mptcp-level ack update. In such case, this work will be either
done from work queue or recv path, depending on which runs sooner.
In order to avoid pointless scheduling of the work queue, work
will be queued from the mptcp sockets lock release callback.
This allows to detect when the socket owner did drain the subflow
socket receive queue.
Please see individual patches for more information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't schedule the work queue right away, instead defer this
to the lock release callback.
This has the advantage that it will give recv path a chance to
complete -- this might have moved all pending packets from the
subflow to the mptcp receive queue, which allows to avoid the
schedule_work().
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't lock_sock() the mptcp socket from the subflow data_ready callback,
it would result in ABBA deadlock with the subflow socket lock.
We can however grab the spinlock: if that succeeds and the mptcp socket
is not owned at the moment, we can process the new skbs right away
without deferring this to the work queue.
This avoids the schedule_work and hence the small delay until the
work item is processed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only used to discard stale data from the subflow, so move
it where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If userspace never drains the receive buffers we must stop draining
the subflow socket(s) at some point.
This adds the needed rmem accouting for this.
If the threshold is reached, we stop draining the subflows.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
