| Age | Commit message (Collapse) | Author |
|---|
|
Previously, if kvmppc_run_core() was running a VCPU that needed a VPA
update (i.e. one of its 3 virtual processor areas needed to be pinned
in memory so the host real mode code can update it on guest entry and
exit), we would drop the vcore lock and do the update there and then.
Future changes will make it inconvenient to drop the lock, so instead
we now remove it from the list of runnable VCPUs and wake up its
VCPU task. This will have the effect that the VCPU task will exit
kvmppc_run_vcpu(), go around the do loop in kvmppc_vcpu_run_hv(), and
re-enter kvmppc_run_vcpu(), whereupon it will do the necessary call
to kvmppc_update_vpas() and then rejoin the vcore.
The one complication is that the runner VCPU (whose VCPU task is the
current task) might be one of the ones that gets removed from the
runnable list. In that case we just return from kvmppc_run_core()
and let the code in kvmppc_run_vcpu() wake up another VCPU task to be
the runner if necessary.
This all means that the VCORE_STARTING state is no longer used, so we
remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This reads the timebase at various points in the real-mode guest
entry/exit code and uses that to accumulate total, minimum and
maximum time spent in those parts of the code. Currently these
times are accumulated per vcpu in 5 parts of the code:
* rm_entry - time taken from the start of kvmppc_hv_entry() until
just before entering the guest.
* rm_intr - time from when we take a hypervisor interrupt in the
guest until we either re-enter the guest or decide to exit to the
host. This includes time spent handling hcalls in real mode.
* rm_exit - time from when we decide to exit the guest until the
return from kvmppc_hv_entry().
* guest - time spend in the guest
* cede - time spent napping in real mode due to an H_CEDE hcall
while other threads in the same vcore are active.
These times are exposed in debugfs in a directory per vcpu that
contains a file called "timings". This file contains one line for
each of the 5 timings above, with the name followed by a colon and
4 numbers, which are the count (number of times the code has been
executed), the total time, the minimum time, and the maximum time,
all in nanoseconds.
The overhead of the extra code amounts to about 30ns for an hcall that
is handled in real mode (e.g. H_SET_DABR), which is about 25%. Since
production environments may not wish to incur this overhead, the new
code is conditional on a new config symbol,
CONFIG_KVM_BOOK3S_HV_EXIT_TIMING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This creates a debugfs directory for each HV guest (assuming debugfs
is enabled in the kernel config), and within that directory, a file
by which the contents of the guest's HPT (hashed page table) can be
read. The directory is named vmnnnn, where nnnn is the PID of the
process that created the guest. The file is named "htab". This is
intended to help in debugging problems in the host's management
of guest memory.
The contents of the file consist of a series of lines like this:
3f48 4000d032bf003505 0000000bd7ff1196 00000003b5c71196
The first field is the index of the entry in the HPT, the second and
third are the HPT entry, so the third entry contains the real page
number that is mapped by the entry if the entry's valid bit is set.
The fourth field is the guest's view of the second doubleword of the
entry, so it contains the guest physical address. (The format of the
second through fourth fields are described in the Power ISA and also
in arch/powerpc/include/asm/mmu-hash64.h.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add two counters to count how often we generate real-mode ICS resend
and reject events. The counters provide some performance statistics
that could be used in the future to consider if the real mode functions
need further optimizing. The counters are displayed as part of IPC and
ICP state provided by /sys/debug/kernel/powerpc/kvm* for each VM.
Also added two counters that count (approximately) how many times we
don't find an ICP or ICS we're looking for. These are not currently
exposed through sysfs, but can be useful when debugging crashes.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Interrupt-based hypercalls return H_TOO_HARD to inform KVM that it needs
to switch to the host to complete the rest of hypercall function in
virtual mode. This patch ports the virtual mode ICS/ICP reject and resend
functions to be runnable in hypervisor real mode, thus avoiding the need
to switch to the host to execute these functions in virtual mode. However,
the hypercalls continue to return H_TOO_HARD for vcpu_wakeup and notify
events - these events cannot be done in real mode and they will still need
a switch to host virtual mode.
There are sufficient differences between the real mode code and the
virtual mode code for the ICS/ICP resend and reject functions that
for now the code has been duplicated instead of sharing common code.
In the future, we can look at creating common functions.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Replaces the ICS mutex lock with a spin lock since we will be porting
these routines to real mode. Note that we need to disable interrupts
before we take the lock in anticipation of the fact that on the guest
side, we are running in the context of a hard irq and interrupts are
disabled (EE bit off) when the lock is acquired. Again, because we
will be acquiring the lock in hypervisor real mode, we need to use
an arch_spinlock_t instead of a normal spinlock here as we want to
avoid running any lockdep code (which may not be safe to execute in
real mode).
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add counters to track number of times we switch from guest real mode
to host virtual mode during an interrupt-related hyper call because the
hypercall requires actions that cannot be completed in real mode. This
will help when making optimizations that reduce guest-host transitions.
It is safe to use an ordinary increment rather than an atomic operation
because there is one ICP per virtual CPU and kvmppc_xics_rm_complete()
only works on the ICP for the current VCPU.
The counters are displayed as part of IPC and ICP state provided by
/sys/debug/kernel/powerpc/kvm* for each VM.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds helper routines for locking and unlocking HPTEs, and uses
them in the rest of the code. We don't change any locking rules in
this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We don't support real-mode areas now that 970 support is removed.
Remove the remaining details of rma from the code. Also rename
rma_setup_done to hpte_setup_done to better reflect the changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Some PowerNV systems include a hardware random-number generator.
This HWRNG is present on POWER7+ and POWER8 chips and is capable of
generating one 64-bit random number every microsecond. The random
numbers are produced by sampling a set of 64 unstable high-frequency
oscillators and are almost completely entropic.
PAPR defines an H_RANDOM hypercall which guests can use to obtain one
64-bit random sample from the HWRNG. This adds a real-mode
implementation of the H_RANDOM hypercall. This hypercall was
implemented in real mode because the latency of reading the HWRNG is
generally small compared to the latency of a guest exit and entry for
all the threads in the same virtual core.
Userspace can detect the presence of the HWRNG and the H_RANDOM
implementation by querying the KVM_CAP_PPC_HWRNG capability. The
H_RANDOM hypercall implementation will only be invoked when the guest
does an H_RANDOM hypercall if userspace first enables the in-kernel
H_RANDOM implementation using the KVM_CAP_PPC_ENABLE_HCALL capability.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On POWER, storage caching is usually configured via the MMU - attributes
such as cache-inhibited are stored in the TLB and the hashed page table.
This makes correctly performing cache inhibited IO accesses awkward when
the MMU is turned off (real mode). Some CPU models provide special
registers to control the cache attributes of real mode load and stores but
this is not at all consistent. This is a problem in particular for SLOF,
the firmware used on KVM guests, which runs entirely in real mode, but
which needs to do IO to load the kernel.
To simplify this qemu implements two special hypercalls, H_LOGICAL_CI_LOAD
and H_LOGICAL_CI_STORE which simulate a cache-inhibited load or store to
a logical address (aka guest physical address). SLOF uses these for IO.
However, because these are implemented within qemu, not the host kernel,
these bypass any IO devices emulated within KVM itself. The simplest way
to see this problem is to attempt to boot a KVM guest from a virtio-blk
device with iothread / dataplane enabled. The iothread code relies on an
in kernel implementation of the virtio queue notification, which is not
triggered by the IO hcalls, and so the guest will stall in SLOF unable to
load the guest OS.
This patch addresses this by providing in-kernel implementations of the
2 hypercalls, which correctly scan the KVM IO bus. Any access to an
address not handled by the KVM IO bus will cause a VM exit, hitting the
qemu implementation as before.
Note that a userspace change is also required, in order to enable these
new hcall implementations with KVM_CAP_PPC_ENABLE_HCALL.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[agraf: fix compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Export __spin_yield so that the arch_spin_unlock() function can
be invoked from a module. This will be required for modules where
we want to take a lock that is also is acquired in hypervisor
real mode. Because we want to avoid running any lockdep code
(which may not be safe in real mode), this lock needs to be
an arch_spinlock_t instead of a normal spinlock.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
git://people.freedesktop.org/~airlied/linux into v4l_for_linus
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
|
|
Fixes: 817bd7253291 ("dma-buf: cleanup dma_buf_export() to make it
easily extensible")
Stupid copy-paste from me in the above patch leads to the following static
checker warning:
drivers/staging/android/ion/ion.c:1112 ion_share_dma_buf()
error: potentially dereferencing uninitialized 'buffer'.
drivers/staging/android/ion/ion.c
1103 struct dma_buf *ion_share_dma_buf(struct ion_client *client,
1104 struct
ion_handle *handle)
1105 {
1106 struct ion_buffer *buffer;
^^^^^^
1107 struct dma_buf *dmabuf;
1108 bool valid_handle;
1109 DEFINE_DMA_BUF_EXPORT_INFO(exp_info);
1110
1111 exp_info.ops = &dma_buf_ops;
1112 exp_info.size = buffer->size;
^^^^^^
1113 exp_info.flags = O_RDWR;
1114 exp_info.priv = buffer;
^^^^^^
And here also.
1115
This patch corrects this stupidity.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
At present, dma_buf_export() takes a series of parameters, which
makes it difficult to add any new parameters for exporters, if required.
Make it simpler by moving all these parameters into a struct, and pass
the struct * as parameter to dma_buf_export().
While at it, unite dma_buf_export_named() with dma_buf_export(), and
change all callers accordingly.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
|
|
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
|
|
The ALC256 does not have a mixer nid at 0x0b, and there's no
loopback path (the output pins are directly connected to the DACs).
This commit fixes an "num_steps = 0 for NID=0xb (ctl = Beep Playback Volume)"
error (and as a result, problems with amixer/alsamixer).
If there's pcbeep functionality, it certainly isn't controlled by setting an
amp on 0x0b, so disable beep functionality (at least for now).
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1446517
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Roland SC-D70 reports its device class as vendor specific class and
the quirk QUIRK_AUDIO_FIXED_ENDPOINT was used for audio output.
In the quirks table the sampling rate was hard-coded to 44100 Hz
and therefore not worked when the sound module was in 48000 Hz mode.
In this change the quirk is changed to QUIRK_AUDIO_STANDARD_INTERFACE
but as the sound module reports incorrect bSubframeSize in its
descriptors, additional change is made in format.c to detect it and
to override it (which uses the existing code for Edirol SD-90).
Tested both when the sound module was in 44100 Hz mode and 48000 Hz
mode and both audio input and output. MIDI related part of the driver
is not touched.
Signed-off-by: Takamichi Horikawa <takamichiho@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).
This only applies to the tse-configuration with MSGDMA.
This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).
According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b1337541 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert says:
====================
net: Fix "hw csum failure" message flood for ppp tunnel
This patch set addresses bug "Bug 95171 - "hw csum failure" message
flood for ppp tunnel since upgrade to 3.16". The problem is that pppoe
is being used over UDP with UDP checksusm enabled. On receive
checksum conversion turns checksum-unnecessary in checksum-
complete. The PPP receive functions do not properly pull
the checksum over its headers, so that when an encapsulated
checksums is considered the checksum-complete value is incorrect.
This patch adds skb_checksum_complete_unset which can be called
in the receive path in lieu of pulling checksum complete in
layer. This is useful when the packet is being modified (e.g.
decompressed) and the checksum-complete value is no longer
relevant.
In the ppp_receive_frame we call skb_checksum_complete_unset to toss
out checksum-complete. This should eliminate the reported messages.
Alternatively, we could add skb_postpull_rcsum and probably
special case handling for VJ compression if maintaining the
checksum-complete is needed (not clear to me this is worth the
effort).
I haven't tested this since setting up the failure scenario doesn't
seem trivial to configure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE
is set. This is called to discard checksum-complete when packet
is being modified and checksum is not pulled for headers in a layer.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc update from Ohad Ben-Cohen:
"Suman Anna is adding remoteproc support for processors not behind
IOMMUs"
* tag 'remoteproc-4.1-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: add IOMMU hardware capability flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild updates:
"This is the remaining part of kbuild stuff for v4.1-rc1:
- One wew coccinelle script and a clarification of the proposed fix
in bugon.coccinelle
- CONFIG_KERNEL_LZ4 support for extract-ikconfig"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/coccinelle/misc/bugon.cocci: update bug_on conversion warning
scripts/extract-ikconfig: Support LZ4-compressed images.
irqf_oneshot.cocci: add check of devm_request_threaded_irq()
|
|
Pull SCSI fixes from James Bottomley:
"I'd like to say these were a set of regressions for the recent merge
window code. Unfortunately, they all predate the merge window code
(stable cc'd).
There are two fixes for data integrity (mostly only showing up on
module removal), an mvsas crash with expander attached SATA devices
which goes back to the dawn of the driver but is only just being
picked up as sas expanders become a standard item in low end server
hardware, an am53c974 one because the interrupt data isn't fully
initialised before the line is and a megaraid_sas one because it uses
smp_processor_id() to select MSI-X queues and that now triggers a
WARN_ON()"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mvsas: fix panic on expander attached SATA devices
am53c974: Fix crash during modprobe
megaraid_sas: use raw_smp_processor_id()
sd: Fix missing ATO tag check
sd: Unregister integrity profile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Small fixes and improvements to various fbdev drivers"
* tag 'fbdev-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (24 commits)
omapdss: extend pm notifier to handle hibernation
OMAPDSS: Correct video ports description file path in DT binding doc
OMAPDSS: disable VT switch
fbdev: sh_mobile_lcdc: Fix destruction of uninitialized mutex
video: fbdev: sh_mobile_lcdcfb: Fix ROP3 sysfs attribute parsing
fbdev: pm3fb: cleanup some confusing indenting
hyperv: hyperv_fb: match wait_for_completion_timeout return type
video: fbdev: use msecs_to_jiffies for time conversions
fbdev: via/via_clock: fix sparse warning
video: fbdev: make of_device_id array const
fbdev: sm501fb: use memset_io
OMAPDSS: workaround for MFLAG + NV12 issue
OMAPDSS: Add support for MFLAG
OMAPDSS: setup default fifo thresholds
OMAPDSS: DISPC: lock access to DISPC_CONTROL & DISPC_CONFIG
OMAPDSS: DISPC: fix div by zero issue in overlay scaling
OMAPDSS: DISPC: change sync_pclk_edge default value
OMAPDSS: change signal_level & signal_edge enum values
OMAPDSS: DISPC: explicit handling for sync and de levels
OMAPDSS: DISPC: remove OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES
...
|
|
Pull drm updates from Dave Airlie:
"Highlights:
Core:
- Virtual GEM layer merged, this has been around for a long time, and
it provides a software backed device that allows userspace to use
it as a GEM shared memory handler. This makes it a lot easier to
do certain things when you have no GPU but still have to deal with
DRI expectations.
- atomic helper updates.
- framebuffer modifier interface added.
- i2c over auxch displayport fixes.
- fb width/height confusion fixes.
- new driver for ps8622/ps8625 bridge chips
- lots of new panels
i915:
- more plane atomic conversion
- vGPU guest support for XenGT
- Skylake workarounds and fixes
- Y-tiling support
- work on dynamic pagetable allocation
- EU count report param for gen9+
- CHV fixes (no longer prelim)
- remove ilk rc6
- frontbuffer tracking for fbc
- Displayport link rate refactoring
- sprite colorkey refactor
radeon:
- Displayport MST support (not enabled by default)
- non-ATOM native hw auxch support (DCE5+)
- output csc support
- new queries for userspace debug support
- new VCE packet
nouveau:
- gk20a iommu support
- gm107 graphics support
- more gm20x bringup (waiting on signed nvidia fw).
amdkfd:
- multiple kgd instance support
- use 64-bit time accessors
msm:
- stolen memory support
- DSI and dual-DSI support
- snapdragon 410 support
exynos:
- cleanups for atomic and pageflip
imx-drm:
- more media-bus formats
- TV output prep
- drm panel support
tegra:
- hw vblank counter using host1x syncpoints
omap:
- universal plane support
- prep work for atomic modesetting
rcar-du:
- ported to atomic modesetting
atmel-hlcdc:
- ported to atomic modesetting
- added suspend/resume support
sti:
- ported to atomic modesetting
dwhdmi:
- more compliant audio support
- update rockchip phy support
tda998x:
- DT probing for attached crtcs
- simplified EDID reading
rockchip:
- fixes
adv7511:
- fixes"
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (689 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
drm/i915: Dont enable CS_PARSER_ERROR interrupts at all
drm/i915: Move drm_framebuffer_unreference out of struct_mutex for takeover
drm: fix trivial typo mistake
drm: Make integer overflow checking cover universal cursor updates (v2)
drm/nouveau/bios: fix fetching from acpi on certain systems
drm/nouveau/gr/gm206: initial init+ctx code
drm/nouveau/ce/gm206: enable support via gm204 code
drm/nouveau/fifo/gm206: enable support via gm204 code
drm/nouveau/gr/gm204: initial init+ctx code
drm/nouveau: support for buffer moves via MaxwellDmaCopyA
drm/nouveau/ce/gm204: initial support
drm/nouveau: add support for gm20x fifo channels
drm/nouveau/fifo/gm204: initial support
drm/nouveau/gr/gk104-: prevent reading non-existent regs in intr handler
drm/nouveau/gr/gm107: very slightly demagic part of attrib cb setup
drm/nouveau/gr/gk104-: correct crop/zrop num_active_fbps setting
drm/nouveau/gr/gf100-: add symbolic names for classes
drm/nouveau/gr/gm107: support tpc "strand" ctxsw in gpccs ucode
drm/nouveau/gr/gf100-: support mmio access with gpc offset from gpccs ucode
...
|
|
A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Sowmini Varadhan says:
====================
iommu-common build warning fixes.
This patchset has fixes for 2 architectures
- Part 1: x86_64 warnings generated by sparse
- Part 2: allmodconfig build error for powerpc, identified by Guenter Roeck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_DEBUG_FORCE_WEAK_PER_CPU is set, the DEFINE_PER_CPU_SECTION
macro will define an extern __pcpu_unique_##name variable that could
conflict with the same definition in powerpc at this time. Avoid that
conflict by renaming iommu_pool_hash in iommu-common.c
Thanks to Guenter Roeck for catching this, and helping to test the fix.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Declare iommu_large_alloc as static. Remove extern definition for
iommu_tbl_pool_init().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much this time, but the changes include:
- moving domain allocation into the iommu drivers to prepare for the
introduction of default domains for devices
- fixing the IO page-table code in the AMD IOMMU driver to correctly
encode large page sizes
- extension of the PCI support in the ARM-SMMU driver
- various fixes and cleanups"
* tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (34 commits)
iommu/amd: Correctly encode huge pages in iommu page tables
iommu/amd: Optimize amd_iommu_iova_to_phys for new fetch_pte interface
iommu/amd: Optimize alloc_new_range for new fetch_pte interface
iommu/amd: Optimize iommu_unmap_page for new fetch_pte interface
iommu/amd: Return the pte page-size in fetch_pte
iommu/amd: Add support for contiguous dma allocator
iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent
iommu/amd: Ignore BUS_NOTIFY_UNBOUND_DRIVER event
iommu/amd: Use BUS_NOTIFY_REMOVED_DEVICE
iommu/tegra: smmu: Compute PFN mask at runtime
iommu/tegra: gart: Set aperture at domain initialization time
iommu/tegra: Setup aperture
iommu: Remove domain_init and domain_free iommu_ops
iommu/fsl: Make use of domain_alloc and domain_free
iommu/rockchip: Make use of domain_alloc and domain_free
iommu/ipmmu-vmsa: Make use of domain_alloc and domain_free
iommu/shmobile: Make use of domain_alloc and domain_free
iommu/msm: Make use of domain_alloc and domain_free
iommu/tegra-gart: Make use of domain_alloc and domain_free
iommu/tegra-smmu: Make use of domain_alloc and domain_free
...
|
|
With the recent changes omaps have developed a dependency to MFD_SYSCON.
This is used for system control module generic register area and some
clocks.
We do have it selected in omap2plus_defconfig, but targeted config
files may not have it selected. Let's make sure it's selected like
few other ARM platforms are already doing.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Martin Schwidefsky:
"The big thing in this second merge for s390 is the new eBPF JIT from
Michael which replaces the old 32-bit backend.
The remaining commits are bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: add locking for fmb access
s390/pci: extract software counters from fmb
s390/dasd: Fix unresumed device after suspend/resume having no paths
s390/dasd: fix unresumed device after suspend/resume
s390/dasd: fix inability to set a DASD device offline
s390/mm: Fix memory hotplug for unaligned standby memory
s390/bpf: Add s390x eBPF JIT compiler backend
s390: Use bool function return values of true/false not 1/0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68k fixes from Greg Ungerer:
"Nothing big, spelling fixes and fix/cleanup for ColdFire eth device setup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix fec setup warning for ColdFire 5271 builds
m68knommu: ColdFire 5271 only has a single FEC controller
m68k: Fix trivial typos in comments
|
|
Yes, it should work, but it's a bad idea. Not only did ARM64 not have
the 16-bit access code (there's a separate patch to add it), it's just
not a good atomic type. Some architectures fundamentally don't do
atomic accesses in them (alpha), and it's not like it saves any space
here anyway because of structure packing issues.
We normally should aim for flags to be "unsigned int" or "unsigned
long". And if space is at a premium, use a single byte (although that
causes problems on alpha again). There might be very special cases
where a 16-byte entity is really wanted, but this is not one of them.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If a directory is complete, we want to keep the exclusive
cap. So that MDS does not end up revoking the shared cap
on every create/unlink operation.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
|
|
No need to do single_open()'s job ourselves.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Don't pollute /proc/mounts with default options (presently these are
dcache, nofsc and acl). Leave the acl/noacl however - it's a bit of
a special case due to CONFIG_CEPH_FS_POSIX_ACL.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
