| Age | Commit message (Collapse) | Author |
|---|
|
Replace the enable, disable and config pwm_ops with an apply op,
to support the new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-13-hdegoede@redhat.com
|
|
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
So far we've kept the PWM_OUTPUT_ENABLE bit set when disabling the PWM,
this commit makes crc_pwm_disable() clear it on disable and makes
crc_pwm_enable() set it again on re-enable.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-12-hdegoede@redhat.com
|
|
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
The BACKLIGHT_EN register at address 0x51 really controls a separate
output-only GPIO which is earmarked to be used as output connected to the
backlight-enable pin for LCD panels, this GPO is part of the PMIC's
"Display Panel Control Block." . This pin should probably be moved over
to a GPIO provider driver (and consumers modified accordingly), but that
is something for an(other) patch.
Enabling / disabling the actual PWM output is controlled by the
PWM_OUTPUT_ENABLE bit of the PWM0_CLK_DIV register.
As the comment in the old code already indicates we must disable the PWM
before we can change the clock divider. But the crc_pwm_disable() and
crc_pwm_enable() calls the old code make for this only change the
BACKLIGHT_EN register; and the value of that register does not matter for
changing the period / the divider. What does matter is that the
PWM_OUTPUT_ENABLE bit must be cleared before a new value can be written.
This commit modifies crc_pwm_config() to clear PWM_OUTPUT_ENABLE instead
when changing the period, so that period changes actually work.
Note this fix will cause a significant behavior change on some devices
using the CRC PWM output to drive their backlight. Before the PWM would
always run with the output frequency configured by the BIOS at boot, now
the period time specified by the i915 driver will actually be honored.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-11-hdegoede@redhat.com
|
|
The CRC PWM controller has a clock-divider which divides the clock with
a value between 1-128. But as can seen from the PWM_DIV_CLK_xxx
defines, this range maps to a register value of 0-127.
So after calculating the clock-divider we must subtract 1 to get the
register value, unless the requested frequency was so high that the
calculation has already resulted in a (rounded) divider value of 0.
Note that before this fix, setting a period of PWM_MAX_PERIOD_NS which
corresponds to the max. divider value of 128 could have resulted in a
bug where the code would use 128 as divider-register value which would
have resulted in an actual divider value of 0 (and the enable bit being
set). A rounding error stopped this bug from actually happen. This
same rounding error means that after the subtraction of 1 it is impossible
to set the divider to 128. Also bump PWM_MAX_PERIOD_NS by 1 ns to allow
setting a divider of 128 (register-value 127).
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-10-hdegoede@redhat.com
|
|
While looking into adding atomic-pwm support to the pwm-crc driver I
noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and
there is a clock-divider which divides this with a value between 1-128,
and there are 256 duty-cycle steps.
The pwm-crc code before this commit assumed that a clock-divider
setting of 1 means that the PWM output is running at 6 MHZ, if that
is true, where do these 256 duty-cycle steps come from?
This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that
seems unlikely for a PMIC which is using a silicon process optimized for
power-switching transistors. It is way more likely that there is an 8
bit counter for the duty cycle which acts as an extra fixed divider
wrt the PWM output frequency.
The main user of the pwm-crc driver is the i915 GPU driver which uses it
for backlight control. Lets compare the PWM register values set by the
video-BIOS (the GOP), assuming the extra fixed divider is present versus
the PWM frequency specified in the Video-BIOS-Tables:
Device: PWM Hz set by BIOS PWM Hz specified in VBT
Asus T100TA 200 200
Asus T100HA 200 200
Lenovo Miix 2 8 23437 20000
Toshiba WT8-A 23437 20000
So as we can see if we assume the extra division by 256 then the register
values set by the GOP are an exact match for the VBT values, where as
otherwise the values would be of by a factor of 256.
This commit fixes the period / duty_cycle calculations to take the
extra division by 256 into account.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-9-hdegoede@redhat.com
|
|
PWM controller drivers should not restore the PWM state on resume. The
convention is that PWM consumers do this by calling pwm_apply_state(),
so that it can be done at the exact moment when the consumer needs
the state to be stored, avoiding e.g. backlight flickering.
The only in kernel consumers of the pwm-lpss code, the i915 driver
and the pwm-class sysfs interface code both correctly restore the
state on resume, so there is no need to do this in the pwm-lpss code.
More-over the removed resume handler is buggy, since it blindly
restores the ctrl-register contents without setting the update
bit, which is necessary to get the controller to actually use/apply
the restored base-unit and on-time-div values.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-8-hdegoede@redhat.com
|
|
Before this commit pwm_lpss_apply() was assuming 2 pre-conditions
were met by the existing hardware state:
1. That the base-unit and on-time-div read back from the
control register are those actually in use, so that it
can skip setting the update bit if the read-back value
matches the desired values.
2. That the controller is enabled when the cached
pwm_state.enabled says that the controller is enabled.
As the long history of fixes for subtle (often suspend/resume)
lpss-pwm issues shows, these assumptions are not necessary
always true.
1. Specifically is not true on some (*) Cherry Trail devices
with a nasty GFX0._PS3 method which: a. saves the ctrl reg value.
b. sets the base-unit to 0 and writes the update bit to apply/commit
c. restores the original ctrl value without setting the update bit,
so that the 0 base-unit value is still in use.
2. Assumption 2. currently is true, but only because of the code which
saves/restores the state on suspend/resume. By convention restoring the
PWM state should be done by the PWM consumer and the presence of this
code in the pmw-lpss driver is a bug. Therefor the save/restore code will
be dropped in the next patch in this series, after which this assumption
also is no longer true.
This commit changes the pwm_lpss_apply() to not make any assumptions about
the state the hardware is in. Instead it makes pwm_lpss_apply() always
fully program the PWM controller, making it much less fragile.
*) Seen on the Acer One 10 S1003, Lenovo Ideapad Miix 310 and 320 models
and various Medion models.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-7-hdegoede@redhat.com
|
|
In the not-enabled -> enabled path pwm_lpss_apply() needs to get a
runtime-pm reference; and then on any errors it needs to release it
again.
This leads to somewhat hard to read code. This commit introduces a new
pwm_lpss_prepare_enable() helper and moves all the steps necessary for
the not-enabled -> enabled transition there, so that we can error check
the entire transition in a single place and only have one pm_runtime_put()
on failure call site.
While working on this I noticed that the enabled -> enabled (update
settings) path was quite similar, so I've added an enable parameter to
the new pwm_lpss_prepare_enable() helper, which allows using it in that
path too.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-6-hdegoede@redhat.com
|
|
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
|
|
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets turned off from the _PS3 method of the graphics-card dev:
Method (_PS3, 0, Serialized) // _PS3: Power State 3
{
...
PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
PSAT |= 0x03
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
...
}
Where PSAT is the power-status register of the PWM controller.
Since the i915 driver will do a pwm_get on the pwm device as it uses it to
control the LCD panel backlight, there is a device-link marking the i915
device as a consumer of the pwm device. So that the PWM controller will
always be suspended after the i915 driver suspends (which is the right
thing to do). This causes the above GFX0 PS3 AML code to run before
acpi_lpss.c calls acpi_lpss_save_ctx().
So on these devices the PWM controller will already be off when
acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff)
as ctx register values.
When these bogus values get restored on resume the PWM controller actually
keeps working, since most bits are reserved, but this does set bit 3 of
the LPSS General purpose register, which for the PWM controller has the
following function: "This bit is re-used to support 32kHz slow mode.
Default is 19.2MHz as PWM source clock".
This causes the clock of the PWM controller to switch from 19.2MHz to
32KHz, which is a slow-down of a factor 600. Surprisingly enough so far
there have been few bug reports about this. This is likely because the
i915 driver was hardcoding the PWM frequency to 46 KHz, which divided
by 600 would result in a PWM frequency of approx. 78 Hz, which mostly
still works fine. There are some bug reports about the LCD backlight
flickering after suspend/resume which are likely caused by this issue.
But with the upcoming patch-series to finally switch the i915 drivers
code for external PWM controllers to use the atomic API and to honor
the PWM frequency specified in the video BIOS (VBT), this becomes a much
bigger problem. On most cases the VBT specifies either 200 Hz or 20
KHz as PWM frequency, which with the mentioned issue ends up being either
1/3 Hz, where the backlight actually visible blinks on and off every 3s,
or in 33 Hz and horrible flickering of the backlight.
There are a number of possible solutions to this problem:
1. Make acpi_lpss_save_ctx() run before GFX0._PS3
Pro: Clean solution from pov of not medling with save/restore ctx code
Con: As mentioned the current ordering is the right thing to do
Con: Requires assymmetry in at what suspend/resume phase we do the save vs
restore, requiring more suspend/resume ordering hacks in already
convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
Pro: Reasonably clean
Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
Pro: Not PWM specific, might help with issues on other LPSS devices too
Con: If we can get away with not restoring the ctx why bother with it at
all?
4. Do not save the ctx for CHT PWM controllers
Pro: Clean, as simple as dropping a flag?
Con: Not so simple as dropping a flag, needs a new flag to ensure that
we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
Pro: Keeps acpi_lpss.c code clean
Con: Moves knowledge of LPSS-context into the pwm-lpss.c code
1 and 5 both do not seem to be a desirable way forward.
3 and 4 seem ok, but they both assume that restoring the LPSS-context
registers is not necessary. I have done a couple of test and those do
show that restoring the LPSS-context indeed does not seem to be necessary
on devices using s2idle suspend (and successfully reaching S0i3). But I
have no hardware to test deep / S3 suspend. So I'm not sure that not
restoring the context is safe.
That leaves solution 2, which is about as simple / clean as 3 and 4,
so this commit fixes the described problem by implementing a new
LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-3-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets poked from the _PS0 method of the graphics-card device:
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
If (((Local0 & 0x03) == 0x03))
{
PSAT &= 0xFFFFFFFC
Local1 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
RSTA = Zero
RSTF = Zero
RSTA = One
RSTF = One
PWMB |= 0xC0000000
PWMC = PWMB /* \_SB_.PCI0.GFX0.PWMB */
}
Where PSAT is the power-status register of the PWM controller, so if it
is in D3 when the GFX0 device's PS0 method runs then it will turn it on
and restore the PWM ctrl register value it saved from its PS3 handler.
Note not only does it restore it, it ors it with 0xC0000000 turning it
on at a time where we may not want it to get turned on at all.
The pwm_get call which the i915 driver does to get a reference to the
PWM controller, already adds a device-link making the GFX0 device a
consumer of the PWM device. So it should already have been resumed when
the above AML runs and the AML should thus not do its undesirable poking
of the PWM controller register.
But the PCI core powers on PCI devices in the no-irq resume phase and
thus calls the troublesome PS0 method in the no-irq resume phase.
Where as LPSS devices by default are resumed in the early resume phase.
This commit sets the resume_from_noirq flag in the bsw_pwm_dev_desc
struct, so that Cherry Trail PWM controllers will be resumed in the
no-irq phase. Together with the device-link added by the pwm-get this
ensures that the PWM controller will be on when the troublesome PS0
method runs, which stops it from poking the PWM controller.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-2-hdegoede@redhat.com
|
|
While looking for ->files in ->defer_list, consider that requests there
may actually be links.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
While trying to cancel requests with ->files, it also should look for
requests in ->defer_list, otherwise it might end up hanging a thread.
Cancel all requests in ->defer_list up to the last request there with
matching ->files, that's needed to follow drain ordering semantics.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
'clang-format-for-linus-v5.9-rc4' and 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux
Pull misc fixes from Miguel Ojeda:
"A trivial patch for auxdisplay:
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
The usual clang-format trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
And Luc requested me to pick a sparse fix on my queue, so here it goes
along with other two trivial Compiler Attributes ones (also from Luc).
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van
Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van
Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting
__has_attribute (Luc Van Oostenryck)"
* tag 'auxdisplay-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
auxdisplay: Replace HTTP links with HTTPS ones
* tag 'clang-format-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
clang-format: Update with the latest for_each macro list
* tag 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
sparse: use static inline for __chk_{user,io}_ptr()
Compiler Attributes: fix comment concerning GCC 4.6
Compiler Attributes: remove comment about sparse not supporting __has_attribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- HSDK-4xd Dev system: perf driver updates for sampling interrupt
- HSDK* Dev System: Ethernet broken [Evgeniy Didin]
- HIGHMEM broken (2 memory banks) [Mike Rapoport]
- show_regs() rewrite once and for all
- Other minor fixes
* tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id
arc: fix memory initialization for systems with two memory banks
irqchip/eznps: Fix build error for !ARC700 builds
ARC: show_regs: fix r12 printing and simplify
ARC: HSDK: wireup perf irq
ARC: perf: don't bail setup if pct irq missing in device-tree
ARC: pgalloc.h: delete a duplicated word + other fixes
|
|
Merge misc fixes from Andrew Morton:
"19 patches.
Subsystems affected by this patch series: MAINTAINERS, ipc, fork,
checkpatch, lib, and mm (memcg, slub, pagemap, madvise, migration,
hugetlb)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
mm: memcg: fix memcg reclaim soft lockup
memcg: fix use-after-free in uncharge_batch
|
|
Otherwise gcc generates warnings if the expression is complicated.
Fixes: 312a0c170945 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
collapse_file() in khugepaged passes PAGE_SIZE as the number of pages to
be read to page_cache_sync_readahead(). The intent was probably to read
a single page. Fix it to use the number of pages to the end of the
window instead.
Fixes: 99cb0dbd47a1 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <shy828301@gmail.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Eric Biggers <ebiggers@google.com>
Link: https://lkml.kernel.org/r/20200903140844.14194-2-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
CPU0: CPU1:
proc_sys_write
hugetlb_sysctl_handler proc_sys_call_handler
hugetlb_sysctl_handler_common hugetlb_sysctl_handler
table->data = &tmp; hugetlb_sysctl_handler_common
table->data = &tmp;
proc_doulongvec_minmax
do_proc_doulongvec_minmax sysctl_head_finish
__do_proc_doulongvec_minmax unuse_table
i = table->data;
*i = val; // corrupt CPU1's stack
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
The following oops was seen:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Code: Bad RIP value.
...
Call Trace:
? set_max_huge_pages+0x3da/0x4f0
? alloc_pool_huge_page+0x150/0x150
? proc_doulongvec_minmax+0x46/0x60
? hugetlb_sysctl_handler_common+0x1c7/0x200
? nr_hugepages_store+0x20/0x20
? copy_fd_bitmaps+0x170/0x170
? hugetlb_sysctl_handler+0x1e/0x20
? proc_sys_call_handler+0x2f1/0x300
? unregister_sysctl_table+0xb0/0xb0
? __fd_install+0x78/0x100
? proc_sys_write+0x14/0x20
? __vfs_write+0x4d/0x90
? vfs_write+0xef/0x240
? ksys_write+0xc0/0x160
? __ia32_sys_read+0x50/0x50
? __close_fd+0x129/0x150
? __x64_sys_write+0x43/0x50
? do_syscall_64+0x6c/0x200
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e5ff215941d5 ("hugetlb: multiple hstates for multiple page sizes")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit cf11e85fc08c ("mm: hugetlb: optionally allocate gigantic
hugepages using cma"), the gigantic page would be allocated from node
which is not the preferred node, although there are pages available from
that node. The reason is that the nid parameter has been ignored in
alloc_gigantic_page().
Besides, the __GFP_THISNODE also need be checked if user required to
alloc only from the preferred node.
After this patch, the preferred node is tried first before other allowed
nodes, and don't try to allocate from other nodes if __GFP_THISNODE is
specified. If user don't specify the preferred node, the current node
will be used as preferred node, which makes sure consistent behavior of
allocating gigantic and non-gigantic hugetlb page.
Fixes: cf11e85fc08c ("mm: hugetlb: optionally allocate gigantic hugepages using cma")
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Link: https://lkml.kernel.org/r/20200902025016.697260-1-lixinhai.lxh@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code to remove a migration PTE and replace it with a device private
PTE was not copying the soft dirty bit from the migration entry. This
could lead to page contents not being marked dirty when faulting the page
back from device private memory.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200831212222.22409-3-rcampbell@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm/migrate: preserve soft dirty in remove_migration_pte()".
I happened to notice this from code inspection after seeing Alistair
Popple's patch ("mm/rmap: Fixup copying of soft dirty and uffd ptes").
This patch (of 2):
The check for is_zone_device_page() and is_device_private_page() is
unnecessary since the latter is sufficient to determine if the page is a
device private page. Simplify the code for easier reading.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Link: https://lkml.kernel.org/r/20200831212222.22409-1-rcampbell@nvidia.com
Link: https://lkml.kernel.org/r/20200831212222.22409-2-rcampbell@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During memory migration a pte is temporarily replaced with a migration
swap pte. Some pte bits from the existing mapping such as the soft-dirty
and uffd write-protect bits are preserved by copying these to the
temporary migration swap pte.
However these bits are not stored at the same location for swap and
non-swap ptes. Therefore testing these bits requires using the
appropriate helper function for the given pte type.
Unfortunately several code locations were found where the wrong helper
function is being used to test soft_dirty and uffd_wp bits which leads to
them getting incorrectly set or cleared during page-migration.
Fix these by using the correct tests based on pte type.
Fixes: a5430dda8a3a ("mm/migrate: support un-addressable ZONE_DEVICE page in migration")
Fixes: 8c3328f1f36a ("mm/migrate: migrate_vma() unmap page from vma while collecting pages")
Fixes: f45ec5ff16a7 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200825064232.10023-2-alistair@popple.id.au
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit f45ec5ff16a75 ("userfaultfd: wp: support swap and page migration")
introduced support for tracking the uffd wp bit during page migration.
However the non-swap PTE variant was used to set the flag for zone device
private pages which are a type of swap page.
This leads to corruption of the swap offset if the original PTE has the
uffd_wp flag set.
Fixes: f45ec5ff16a75 ("userfaultfd: wp: support swap and page migration")
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Link: https://lkml.kernel.org/r/20200825064232.10023-1-alistair@popple.id.au
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The syzbot reported the below use-after-free:
BUG: KASAN: use-after-free in madvise_willneed mm/madvise.c:293 [inline]
BUG: KASAN: use-after-free in madvise_vma mm/madvise.c:942 [inline]
BUG: KASAN: use-after-free in do_madvise.part.0+0x1c8b/0x1cf0 mm/madvise.c:1145
Read of size 8 at addr ffff8880a6163eb0 by task syz-executor.0/9996
CPU: 0 PID: 9996 Comm: syz-executor.0 Not tainted 5.9.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x18f/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xae/0x497 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
madvise_willneed mm/madvise.c:293 [inline]
madvise_vma mm/madvise.c:942 [inline]
do_madvise.part.0+0x1c8b/0x1cf0 mm/madvise.c:1145
do_madvise mm/madvise.c:1169 [inline]
__do_sys_madvise mm/madvise.c:1171 [inline]
__se_sys_madvise mm/madvise.c:1169 [inline]
__x64_sys_madvise+0xd9/0x110 mm/madvise.c:1169
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Allocated by task 9992:
kmem_cache_alloc+0x138/0x3a0 mm/slab.c:3482
vm_area_alloc+0x1c/0x110 kernel/fork.c:347
mmap_region+0x8e5/0x1780 mm/mmap.c:1743
do_mmap+0xcf9/0x11d0 mm/mmap.c:1545
vm_mmap_pgoff+0x195/0x200 mm/util.c:506
ksys_mmap_pgoff+0x43a/0x560 mm/mmap.c:1596
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 9992:
kmem_cache_free.part.0+0x67/0x1f0 mm/slab.c:3693
remove_vma+0x132/0x170 mm/mmap.c:184
remove_vma_list mm/mmap.c:2613 [inline]
__do_munmap+0x743/0x1170 mm/mmap.c:2869
do_munmap mm/mmap.c:2877 [inline]
mmap_region+0x257/0x1780 mm/mmap.c:1716
do_mmap+0xcf9/0x11d0 mm/mmap.c:1545
vm_mmap_pgoff+0x195/0x200 mm/util.c:506
ksys_mmap_pgoff+0x43a/0x560 mm/mmap.c:1596
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It is because vma is accessed after releasing mmap_lock, but someone
else acquired the mmap_lock and the vma is gone.
Releasing mmap_lock after accessing vma should fix the problem.
Fixes: 692fe62433d4c ("mm: Handle MADV_WILLNEED through vfs_fadvise()")
Reported-by: syzbot+b90df26038d1d5d85c97@syzkaller.appspotmail.com
Signed-off-by: Yang Shi <shy828301@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org> [5.4+]
Link: https://lkml.kernel.org/r/20200816141204.162624-1-shy828301@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The usage of "capture group (...)" in the immediate condition after `&&`
results in `$1` being uninitialized. This issues a warning "Use of
uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl
line 2638".
I noticed this bug while running checkpatch on the set of commits from
v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in
their commit message.
This bug was introduced in the script by commit e518e9a59ec3
("checkpatch: emit an error when there's a diff in a changelog"). It
has been in the script since then.
The author intended to store the match made by capture group in variable
`$1`. This should have contained the name of the file as `[\w/]+`
matched. However, this couldn't be accomplished due to usage of capture
group and `$1` in the same regular expression.
Fix this by placing the capture group in the condition before `&&`.
Thus, `$1` can be initialized to the text that capture group matches
thereby setting it to the desired and required value.
Fixes: e518e9a59ec3 ("checkpatch: emit an error when there's a diff in a changelog")
Signed-off-by: Mrinal Pandey <mrinalmni@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Joe Perches <joe@perches.com>
Link: https://lkml.kernel.org/r/20200714032352.f476hanaj2dlmiot@mrinalpandey
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
definition of sysctl_max_threads to match its prototype in
linux/sysctl.h which fixes the following sparse error/warning:
kernel/fork.c:3050:47: warning: incorrect type in argument 3 (different address spaces)
kernel/fork.c:3050:47: expected void *
kernel/fork.c:3050:47: got void [noderef] __user *buffer
kernel/fork.c:3036:5: error: symbol 'sysctl_max_threads' redeclared with different type (incompatible argument 3 (different address spaces)):
kernel/fork.c:3036:5: int extern [addressable] [signed] [toplevel] sysctl_max_threads( ... )
kernel/fork.c: note: in included file (through include/linux/key.h, include/linux/cred.h, include/linux/sched/signal.h, include/linux/sched/cputime.h):
include/linux/sysctl.h:242:5: note: previously declared as:
include/linux/sysctl.h:242:5: int extern [addressable] [signed] [toplevel] sysctl_max_threads( ... )
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200825093647.24263-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
signature of proc_ipc_sem_dointvec to match ctl_table.proc_handler which
fixes the following sparse error/warning:
ipc/ipc_sysctl.c:94:47: warning: incorrect type in argument 3 (different address spaces)
ipc/ipc_sysctl.c:94:47: expected void *buffer
ipc/ipc_sysctl.c:94:47: got void [noderef] __user *buffer
ipc/ipc_sysctl.c:194:35: warning: incorrect type in initializer (incompatible argument 3 (different address spaces))
ipc/ipc_sysctl.c:194:35: expected int ( [usertype] *proc_handler )( ... )
ipc/ipc_sysctl.c:194:35: got int ( * )( ... )
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200825105846.5193-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__apply_to_page_range() is also used to change and/or allocate
page-table pages in the vmalloc area of the address space. Make sure
these changes get synchronized to other page-tables in the system by
calling arch_sync_kernel_mappings() when necessary.
The impact appears limited to x86-32, where apply_to_page_range may miss
updating the PMD. That leads to explosions in drivers like
BUG: unable to handle page fault for address: fe036000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
*pde = 00000000
Oops: 0002 [#1] SMP
CPU: 3 PID: 1300 Comm: gem_concurrent_ Not tainted 5.9.0-rc1+ #16
Hardware name: /NUC6i3SYB, BIOS SYSKLi35.86A.0024.2015.1027.2142 10/27/2015
EIP: __execlists_context_alloc+0x132/0x2d0 [i915]
Code: 31 d2 89 f0 e8 2f 55 02 00 89 45 e8 3d 00 f0 ff ff 0f 87 11 01 00 00 8b 4d e8 03 4b 30 b8 5a 5a 5a 5a ba 01 00 00 00 8d 79 04 <c7> 01 5a 5a 5a 5a c7 81 fc 0f 00 00 5a 5a 5a 5a 83 e7 fc 29 f9 81
EAX: 5a5a5a5a EBX: f60ca000 ECX: fe036000 EDX: 00000001
ESI: f43b7340 EDI: fe036004 EBP: f6389cb8 ESP: f6389c9c
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010286
CR0: 80050033 CR2: fe036000 CR3: 2d361000 CR4: 001506d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: fffe0ff0 DR7: 00000400
Call Trace:
execlists_context_alloc+0x10/0x20 [i915]
intel_context_alloc_state+0x3f/0x70 [i915]
__intel_context_do_pin+0x117/0x170 [i915]
i915_gem_do_execbuffer+0xcc7/0x2500 [i915]
i915_gem_execbuffer2_ioctl+0xcd/0x1f0 [i915]
drm_ioctl_kernel+0x8f/0xd0
drm_ioctl+0x223/0x3d0
__ia32_sys_ioctl+0x1ab/0x760
__do_fast_syscall_32+0x3f/0x70
do_fast_syscall_32+0x29/0x60
do_SYSENTER_32+0x15/0x20
entry_SYSENTER_32+0x9f/0xf2
EIP: 0xb7f28559
Code: 03 74 c0 01 10 05 03 74 b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d 76 00 58 b8 77 00 00 00 cd 80 90 8d 76
EAX: ffffffda EBX: 00000005 ECX: c0406469 EDX: bf95556c
ESI: b7e68000 EDI: c0406469 EBP: 00000005 ESP: bf9554d8
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b EFLAGS: 00000296
Modules linked in: i915 x86_pkg_temp_thermal intel_powerclamp crc32_pclmul crc32c_intel intel_cstate intel_uncore intel_gtt drm_kms_helper intel_pch_thermal video button autofs4 i2c_i801 i2c_smbus fan
CR2: 00000000fe036000
It looks like kasan, xen and i915 are vulnerable.
Actual impact is "on thinkpad X60 in 5.9-rc1, screen starts blinking
after 30-or-so minutes, and machine is unusable"
[sfr@canb.auug.org.au: ARCH_PAGE_TABLE_SYNC_MASK needs vmalloc.h]
Link: https://lkml.kernel.org/r/20200825172508.16800a4f@canb.auug.org.au
[chris@chris-wilson.co.uk: changelog addition]
[pavel@ucw.cz: changelog addition]
Fixes: 2ba3e6947aed ("mm/vmalloc: track which page-table levels were modified")
Fixes: 86cf69f1d893 ("x86/mm/32: implement arch_sync_kernel_mappings()")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> [x86-32]
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org> [5.8+]
Link: https://lkml.kernel.org/r/20200821123746.16904-1-joro@8bytes.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
IA64 isn't really being maintained, so mark it as Odd Fixes only.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/7e719139-450f-52c2-59a2-7964a34eda1f@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nominate Nathan and myself to be point of contact for clang/LLVM related
support, after a poll at the LLVM BoF at Linux Plumbers Conf 2020.
While corporate sponsorship is beneficial, its important to not entrust
the keys to the nukes with any one entity. Should Nathan and I find
ourselves at the same employer, I would gladly step down.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lkml.kernel.org/r/20200825143540.2948637-1-ndesaulniers@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I am leaving Marvell and already do not have access to my @marvell.com
email address. So switching over to my korg mail address or removing my
address there another maintainer is already listed. For the entries
there no other maintainer is listed I will keep looking into patches for
Cavium systems for a while until someone from Marvell takes it over.
Since I might have limited access to hardware and also limited time I
changed state to 'Odd Fixes' for those entries.
Signed-off-by: Robert Richter <rric@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ganapatrao Kulkarni <gkulkarni@marvell.com>
Cc: Sunil Goutham <sgoutham@marvell.com>
CC: Borislav Petkov <bp@alien8.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <wsa@kernel.org>,
Link: https://lkml.kernel.org/r/20200824122050.31164-1-rric@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 52f23478081ae0 ("mm/slub.c: fix corrupted freechain in
deactivate_slab()") suffered an update when picked up from LKML [1].
Specifically, relocating 'freelist = NULL' into 'freelist_corrupted()'
created a no-op statement. Fix it by sticking to the behavior intended
in the original patch [1]. In addition, make freelist_corrupted()
immune to passing NULL instead of &freelist.
The issue has been spotted via static analysis and code review.
[1] https://lore.kernel.org/linux-mm/20200331031450.12182-1-dongli.zhang@oracle.com/
Fixes: 52f23478081ae0 ("mm/slub.c: fix corrupted freechain in deactivate_slab()")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200824130643.10291-1-erosca@de.adit-jv.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We've met softlockup with "CONFIG_PREEMPT_NONE=y", when the target memcg
doesn't have any reclaimable memory.
It can be easily reproduced as below:
watchdog: BUG: soft lockup - CPU#0 stuck for 111s![memcg_test:2204]
CPU: 0 PID: 2204 Comm: memcg_test Not tainted 5.9.0-rc2+ #12
Call Trace:
shrink_lruvec+0x49f/0x640
shrink_node+0x2a6/0x6f0
do_try_to_free_pages+0xe9/0x3e0
try_to_free_mem_cgroup_pages+0xef/0x1f0
try_charge+0x2c1/0x750
mem_cgroup_charge+0xd7/0x240
__add_to_page_cache_locked+0x2fd/0x370
add_to_page_cache_lru+0x4a/0xc0
pagecache_get_page+0x10b/0x2f0
filemap_fault+0x661/0xad0
ext4_filemap_fault+0x2c/0x40
__do_fault+0x4d/0xf9
handle_mm_fault+0x1080/0x1790
It only happens on our 1-vcpu instances, because there's no chance for
oom reaper to run to reclaim the to-be-killed process.
Add a cond_resched() at the upper shrink_node_memcgs() to solve this
issue, this will mean that we will get a scheduling point for each memcg
in the reclaimed hierarchy without any dependency on the reclaimable
memory in that memcg thus making it more predictable.
Suggested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Xunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: http://lkml.kernel.org/r/1598495549-67324-1-git-send-email-xlpang@linux.alibaba.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
syzbot has reported an use-after-free in the uncharge_batch path
BUG: KASAN: use-after-free in instrument_atomic_write include/linux/instrumented.h:71 [inline]
BUG: KASAN: use-after-free in atomic64_sub_return include/asm-generic/atomic-instrumented.h:970 [inline]
BUG: KASAN: use-after-free in atomic_long_sub_return include/asm-generic/atomic-long.h:113 [inline]
BUG: KASAN: use-after-free in page_counter_cancel mm/page_counter.c:54 [inline]
BUG: KASAN: use-after-free in page_counter_uncharge+0x3d/0xc0 mm/page_counter.c:155
Write of size 8 at addr ffff8880371c0148 by task syz-executor.0/9304
CPU: 0 PID: 9304 Comm: syz-executor.0 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1f0/0x31e lib/dump_stack.c:118
print_address_description+0x66/0x620 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report+0x132/0x1d0 mm/kasan/report.c:530
check_memory_region_inline mm/kasan/generic.c:183 [inline]
check_memory_region+0x2b5/0x2f0 mm/kasan/generic.c:192
instrument_atomic_write include/linux/instrumented.h:71 [inline]
atomic64_sub_return include/asm-generic/atomic-instrumented.h:970 [inline]
atomic_long_sub_return include/asm-generic/atomic-long.h:113 [inline]
page_counter_cancel mm/page_counter.c:54 [inline]
page_counter_uncharge+0x3d/0xc0 mm/page_counter.c:155
uncharge_batch+0x6c/0x350 mm/memcontrol.c:6764
uncharge_page+0x115/0x430 mm/memcontrol.c:6796
uncharge_list mm/memcontrol.c:6835 [inline]
mem_cgroup_uncharge_list+0x70/0xe0 mm/memcontrol.c:6877
release_pages+0x13a2/0x1550 mm/swap.c:911
tlb_batch_pages_flush mm/mmu_gather.c:49 [inline]
tlb_flush_mmu_free mm/mmu_gather.c:242 [inline]
tlb_flush_mmu+0x780/0x910 mm/mmu_gather.c:249
tlb_finish_mmu+0xcb/0x200 mm/mmu_gather.c:328
exit_mmap+0x296/0x550 mm/mmap.c:3185
__mmput+0x113/0x370 kernel/fork.c:1076
exit_mm+0x4cd/0x550 kernel/exit.c:483
do_exit+0x576/0x1f20 kernel/exit.c:793
do_group_exit+0x161/0x2d0 kernel/exit.c:903
get_signal+0x139b/0x1d30 kernel/signal.c:2743
arch_do_signal+0x33/0x610 arch/x86/kernel/signal.c:811
exit_to_user_mode_loop kernel/entry/common.c:135 [inline]
exit_to_user_mode_prepare+0x8d/0x1b0 kernel/entry/common.c:166
syscall_exit_to_user_mode+0x5e/0x1a0 kernel/entry/common.c:241
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Commit 1a3e1f40962c ("mm: memcontrol: decouple reference counting from
page accounting") reworked the memcg lifetime to be bound the the struct
page rather than charges. It also removed the css_put_many from
uncharge_batch and that is causing the above splat.
uncharge_batch() is supposed to uncharge accumulated charges for all
pages freed from the same memcg. The queuing is done by uncharge_page
which however drops the memcg reference after it adds charges to the
batch. If the current page happens to be the last one holding the
reference for its memcg then the memcg is OK to go and the next page to
be freed will trigger batched uncharge which needs to access the memcg
which is gone already.
Fix the issue by taking a reference for the memcg in the current batch.
Fixes: 1a3e1f40962c ("mm: memcontrol: decouple reference counting from page accounting")
Reported-by: syzbot+b305848212deec86eabe@syzkaller.appspotmail.com
Reported-by: syzbot+b5ea6fb6f139c8b9482b@syzkaller.appspotmail.com
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Hugh Dickins <hughd@google.com>
Link: https://lkml.kernel.org/r/20200820090341.GC5033@dhcp22.suse.cz
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull xfs fix from Darrick Wong:
"Fix a broken metadata verifier that would incorrectly validate attr
fork extents of a realtime file against the realtime volume"
* tag 'xfs-5.9-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix xfs_bmap_validate_extent_raw when checking attr fork of rt files
|
|
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the xfs filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted xfs filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the ext2 filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted ext2 filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If we exceed UIO_FASTIOV, we don't handle the transition correctly
between an allocated vec for requests that are queued with IOSQE_ASYNC.
Store the iovec appropriately and re-set it in the iter iov in case
it changed.
Fixes: ff6165b2d7f6 ("io_uring: retain iov_iter state over io_read/io_write calls")
Reported-by: Nick Hill <nick@nickhill.org>
Tested-by: Norman Maurer <norman.maurer@googlemail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix GENERIC_LOCKBREAK dependency on PREEMPTION in Kconfig broken
because of a typo
- Update defconfigs
* tag 's390-5.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390: fix GENERIC_LOCKBREAK dependency typo in Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix the loading of modules built with binutils-2.35. This version
produces writable and executable .text.ftrace_trampoline section
which is rejected by the kernel.
- Remove the exporting of cpu_logical_map() as the Tegra driver has now
been fixed and no longer uses this function.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/module: set trampoline section flags regardless of CONFIG_DYNAMIC_FTRACE
arm64: Remove exporting cpu_logical_map symbol
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
"A few MIPS fixes:
- fallthrough fallout fix
- BMIPS fixes
- MSA fix to avoid leaking MSA register contents
- Loongson perf and cpu feature fix
- SNI interrupt fix"
* tag 'mips_fixes_5.9_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: SNI: Fix SCSI interrupt
MIPS: add missing MSACSR and upper MSA initialization
MIPS: perf: Fix wrong check condition of Loongson event IDs
mips/oprofile: Fix fallthrough placement
MIPS: Loongson64: Remove unnecessary inclusion of boot_param.h
MIPS: BMIPS: Also call bmips_cpu_setup() for secondary cores
MIPS: mm: BMIPS5000 has inclusive physical caches
MIPS: Loongson64: Do not override watch and ejtag feature
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix documents
- fix warning in 'make localmodconfig'
* tag 'kbuild-fixes-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: remove redundant assignment prompt = prompt
kbuild: Documentation: clean up makefiles.rst
kconfig: streamline_config.pl: check defined(ENV variable) before using it
Documentation/llvm: Improve formatting of commands, variables, and arguments
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix reference counting in the operating performance points (OPP)
framework and address a few intel_pstate driver issues, mostly related
to switching driver operation modes and similar with hardware-managed
P-states (HWP) enabled.
Specifics:
- Fix reference counting of operating performance points (OPP) tables
(Viresh Kumar).
- Address intel_pstate driver interface issues, mostly related to
switching operation modes and handling CPU offline and online and
system-wide suspend/resume with hardware-managed P-states (HWP)
enabled (Rafael Wysocki).
- Fix the maximum frequency computation in the intel_pstate driver
with turbo P-states disabled by the platform firmware and HWP
enabled (Francisco Jerez)"
* tag 'pm-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max() for turbo disabled
cpufreq: intel_pstate: Free memory only when turning off
cpufreq: intel_pstate: Add ->offline and ->online callbacks
cpufreq: intel_pstate: Tweak the EPP sysfs interface
cpufreq: intel_pstate: Update cached EPP in the active mode
cpufreq: intel_pstate: Refuse to turn off with HWP enabled
opp: Don't drop reference for an OPP table that was never parsed
|
|
Pull libata fixes from Jens Axboe:
- improve Sandisks ATA_HORKAGE on NCQ (Tejun)
- link printk cleanup (Xu)
* tag 'libata-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
libata: implement ATA_HORKAGE_MAX_TRIM_128M and apply to Sandisks
ata: ahci: use ata_link_info() instead of ata_link_printk()
|
|
Pull block fixes from Jens Axboe:
"A bit larger than usual this week, mostly due to the NVMe fixes
arriving late for -rc3 and hence didn't make last weeks pull request.
- NVMe:
- instance leak and io boundary fixes from Keith
- fc locking fix from Christophe
- various tcp/rdma reset during traffic fixes from Sagi
- pci use-after-free fix from Tong
- tcp target null deref fix from Ziye
- Locking fix for partition removal (Christoph)
- Ensure bdi->io_pages is always set (me)
- Fixup for hd struct reference (Ming)
- Fix for zero length bvecs (Ming)
- Two small blk-iocost fixes (Tejun)"
* tag 'block-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
block: allow for_each_bvec to support zero len bvec
blk-stat: make q->stats->lock irqsafe
blk-iocost: ioc_pd_free() shouldn't assume irq disabled
block: fix locking in bdev_del_partition
block: release disk reference in hd_struct_free_work
block: ensure bdi->io_pages is always initialized
nvme-pci: cancel nvme device request before disabling
nvme: only use power of two io boundaries
nvme: fix controller instance leak
nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()'
nvme: Fix NULL dereference for pci nvme controllers
nvme-rdma: fix reset hang if controller died in the middle of a reset
nvme-rdma: fix timeout handler
nvme-rdma: serialize controller teardown sequences
nvme-tcp: fix reset hang if controller died in the middle of a reset
nvme-tcp: fix timeout handler
nvme-tcp: serialize controller teardown sequences
nvme: have nvme_wait_freeze_timeout return if it timed out
nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance
nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu
|
|
Pull io_uring fixes from Jens Axboe:
- EAGAIN with O_NONBLOCK retry fix
- Two small fixes for registered files (Jiufei)
* tag 'io_uring-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
io_uring: no read/write-retry on -EAGAIN error and O_NONBLOCK marked file
io_uring: set table->files[i] to NULL when io_sqe_file_register failed
io_uring: fix removing the wrong file in __io_sqe_files_update()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix bogus thermal shutdowns for omap4430 where bogus values resulting
from an incorrect ADC conversion are too high and fire an emergency
shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Fix use-after-free in thermal_zone_device_unregister()
thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430
|
|
Disable the RPTR shadow across all targets. It will be selectively
re-enabled later for targets that need it.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
