| Age | Commit message (Collapse) | Author |
|---|
|
Properly document the transmit buffer bits using an enum and
kernel-doc documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add kernel-doc documentation for enum iwl_debug_cmds, linking the
structures used by the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This improves documentation, since kernel-doc can't deal with the
union well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.
Note: This fix is only for DRAM collection mode.
For other modes, an additional fix will be
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fix the enum link by adding the missing & and provide the link
to the TX response documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.
Fixes: ab02165ccec4 ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.
This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.
Fixes: 206eea783385 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Show the name of the member (scanned_channels) that provides the
length with some better markup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The firmware moved the development from a0 MAC to z0.
z0 is using the same RFID and device ID as a0 so we only
need to switch the name.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Shaul reported that when iwlmvm was sending beacons, it didn't properly
also take ownership of the probe responses. This is because the whole
mac80211 callback (tx_last_beacon) wasn't implemented. Fix that to make
IBSS discovery work better.
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It's safer to use scnprintf() here because the buffer might
be too short for the full format strings. In most cases
this isn't true because of external limits on the values.
In one case, this fixes a stack data leak.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34e2 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.
The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.
Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
ath.git patches for 4.13. Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
|
|
This fixes spin-forever in irq handler when IRQ is already asserted
at request_irq() time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
To yield better user experience, have btcoex control LPS's parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If LPS is controlled by btcoex, this function tell driver LPS is on or off.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If RX ampdu is too long, BT will have less time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add btcoex record pwr mode to control LPS's parameters and share time
with BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We extend types of special packets to a enumeration from boolean value.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The number of debugging conditions now exceeds the capabilities of a
32-bit word.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the driver itself will enter power saving mode dynamically
according to the traffic, we set hw capability SUPPORTS_PS and
SUPPORTS_DYNAMIC_PS in case of fwctrl_lps.
The process IEEE80211_CONF_CHANGE_PS in op_config is used by
SW-LPS only, so we add constraints to avoid errors.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: vincent_fann <vincent_fann@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
To make ant_sel work, we should call power_on_setting to set antenna
correctly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This commit fixies two problems. The first one is interface types
(e.g. PCI) that are used to switch antenna, and the second is to add
wifi_only parameter to give correct state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
New btcoex add a function 'bind' to connect adapter, so we should call
it during initializing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
RS9113 chipset supports Coex feature. Initial frame exchanges during
device initialization happens on coex queue. This patch adds the
handling for coex queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Before firmware load, sometimes false interrupts are received.
System hang is observed if interrupt handler is not registered
to receive these interrupts. Hence interrupt handler registration
is moved before firmware load. We will drop these false interrupts
as these are not from the device.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
