| Age | Commit message (Collapse) | Author |
|---|
|
These peripherals can only be muxed to these pins, so they are
associated in the DTSI instead of the board files. This makes it very
easy to enable them using overlays or u-boot commands:
=> fdt set /soc/i2c@01c2ac00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
These are the only possible pins for these peripherals according to the
datasheet.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
These H3 boards all expose UART1-3 on their expansion header. Since
other functions can be muxed to these pins, they are explicitly
disabled. To enable them, one could use DT overlays or U-boot commands:
=> fdt set /soc/serial@01c28c00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.
The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ga10h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a node enabling the gsl3670 touchscreen controller found on
sun8i-a23-polaroid-mid2809pxe04 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a node enabling the gsl1680 touchscreen controller found on
sun8i-a23-polaroid-mid2407pxe03 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The inet86dz tablet has a gsl1680 touchscreen,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gt90h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND,
an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI,
I2S and LCD.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The GR8 is an SoC made by Nextthing loosely based on the sun5i family.
Since it's not clear yet what we can factor out and merge with the A10s and
A13 support, let's keep it out of the sun5i.dtsi include tree. We will
figure out what can be shared when things settle down.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The usbphy and usb_otg nodes in the A23 and A33 dts files only differ
by compatible, and for the usbphy, the size of one of its register
regions.
Move all the common bits to the A23/A33 common dtsi file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The LCD output needs to be muxed. Add the proper pinctrl node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add all the needed blocks to the A33 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that we have support for the CCU driver in sunxi-ng, convert the A23
and A33 DTs to that driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that we have a different clock representation, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
|
|
The sunxi-ng clock driver is useless for other architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add support for the clock unit found in the A23. Due to the similarities
with the A33, it also shares its clock IDs to allow sharing the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
This commit introduces the clocks found in the Allwinner A33 CCU.
Since this SoC is very similar to the A23, and we share a significant share
of the DTSI, the clock IDs that are going to be used will also be shared
with the A23, hence the name of the various header files.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add support for the class with a single factor, N, being a multiplier.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a new macro to declare muxes based on a table and a gate.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some dividers might have a maximum value that is lower than the width of
the register.
Add a field to _ccu_div to handle those case properly. If the field is set
to 0, the code will assume that the maximum value is the maximum one that
can be used with the field register width.
Otherwise, we'll use whatever value has been set.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The internal _ccu_div structure is meant to be embedded into other
structures to combine the various dividers and to form the clock classes
support.
Start to document those structures by using kerneldoc.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add some macros to ease the declaration of clocks that are using them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Guangzhou FriendlyARM Computer Tech Co., Ltd is a Chinese ARM board vendor.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.
The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.
This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
Note currently the dts is pretty much empty (except for including the
pc-plus dts), I've a local patch which enables the emac actually making
this dts different from the pc-plus one, but that needs the h3 emac
driver to get merged first.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Update the sun8i-h3-orangepi-plus.dts model string to reflect that it
is valid for both the Orange Pi Plus and the Orange Pi Plus 2.
This is also meant to help users realize that it is not valid for
the new Orange Pi Plus 2E, which will get its own dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features
volume buttons, micro-usb otg, headphone connector and a power button.
On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there
is also a accompanied board which has a Goodix GT9271 soldered.
As this board is desired to create tablets with a Home key dealed by
GT9271, a LED is present at the front panel at the position of the
Home key.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The R_PIO device node is missing #interrupt-cells, which causes
interrupt parsing to fail to match it as a valid interrupt controller.
Add #interrupt-cells to it. Also remove the unnecesary #address-cells
and #size-cells.
Fixes: 1ac56a6da9e1 ("ARM: dts: sun9i: Add A80 R_PIO pin controller device
node")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Rename the reference-design-tablet touchscreen node from gsl1680 to
touchscreen, all? tablets seem to use the same power and interrupt
gpio-s, but not all tablets use a gsl1680 controller making the
gsl1680 name somewhat misleading.
Also move the reg and compatible property to the actual tablet dts
as they may differ per tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13
tablet, with micro-usb (otg), headphone and micro-sd slots on the
outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
Note currently the dts for this is somewhat empty. This will change
once we add support for the touchscreen and accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in a nice cleanup :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
A23/A33 has a NAND controller which can now be used properly.
Add a device node for it.
The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.
Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a new style driver for the clock control unit in Allwinner A31/A31s.
A few clocks are still missing:
- MIPI PLL's HDMI mode support
- EMAC clock
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
On sunxi we support cpufreq by changing the clock rate of PLL-CPU.
It's possible the clock output of the PLL goes out of the CPU's
operational limits when the PLL's multipliers / dividers are changed
and it hasn't stabilized yet. This would result in the CPU hanging.
To circumvent this, we temporarily switch the CPU mux clock to another
stable clock before the rate change, and switch it back after the PLL
stabilizes. This is done with clk notifiers registered on the PLL.
This patch adds common functions for notifiers to reparent mux clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Some clocks on the A31 have fixed pre-dividers on multiple parents.
Add support for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Some clock muxes have holes, i.e. invalid or unconnected inputs,
between parent mux values.
Add support for specifying a mux table to map clock parents to
mux values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
