summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-09-23ixgbe: Add small packet padding support for X550Mark Rustad
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which enables padding of small packets. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Correct setting of RDRXCTL register for X550* devicesMark Rustad
Setting the X550* RDRXCTL register should fall through into X540 and 82599, not 82598. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Correct error path in semaphore handlingMark Rustad
The timeout path is supposed to release the semaphore, so do that. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add I2C bus mux supportMark Rustad
Take control of an I2C mux that selects which SFP is attached to the I2C bus. The control of the mux is captured in the taking and releasing of the related semaphore. Because only port 1 can control the mux, port 1 always leaves the mux set to select port 0. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Limit SFP polling rateMark Rustad
Reduce the frequency of polling for SFP modules. Because the service task sometimes runs at high rates, we can poll for SFPs too often. When an SFP is not present, the I2C timeouts that result are very costly. So, prevent SFP polling from being done more than once every two seconds. To reduce latency, the poll time is cleared in a couple of cases to permit the next service task execution to poll the SFP module. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Allow SFP+ on more than 82598 and 82599Mark Rustad
Since SFP+ can be used with some X550 devices, permit them to be detected. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add logic to reset CS4227 when neededMark Rustad
On some hardware platforms, the CS4227 does not initialize properly. Detect those cases and reset it appropriately. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+Mark Rustad
Configures the CS4227 correctly for both 1G and 10G operation, by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It needs to be in this function because we need both the module type and the speed, and this is the only function in the init flow that knows the speed. In contrast, ixgbe_setup_sfp_modules_X550em() does not know the speed, so we can't do anything useful here. This is a fundamental difference from the previous flow, and is due to the way the CS4227 is implemented. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add X550EM_x dual-speed SFP+ supportMark Rustad
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link code was moved from ixgbe_82599.c to ixgbe_common.c for use by X550EM. SFP MAC link code is added to x550EM. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Allow reduced delays during SFP detectionMark Rustad
Reduce the number of retries during PHY detection. This reduces pauses when no SFP is present. Once an SFP is detected, the normal retry count will be used. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Clear I2C destination locationMark Rustad
Clear the destination location for I2C data initially so that the received data will not be affected by previous attempts. This could have returned wrong data in certain retry sequences. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23geneve: use network byte order for destination port config parameterJohn W. Linville
This is primarily for consistancy with vxlan and other tunnels which use network byte order for similar parameters. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net/ethoc: support big-endian register layoutMax Filippov
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-24Merge branch 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie
into drm-fixes radeon and amdgpu fixes for 4.3. It's a bit bigger than usual since it's 3 weeks worth of fixes since I was on vacation, then at XDC. - lots of stability fixes - suspend and resume fixes - GPU scheduler fixes - Misc other fixes * 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux: (31 commits) drm/radeon: add quirk for MSI R7 370 drm/amdgpu: Sprinkle drm_modeset_lock_all to appease locking checks drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks drm/amdgpu: sync ce and me with SWITCH_BUFFER(2) drm/amdgpu: integer overflow in amdgpu_mode_dumb_create() drm/amdgpu: info leak in amdgpu_gem_metadata_ioctl() drm/amdgpu: integer overflow in amdgpu_info_ioctl() drm/amdgpu: unwind properly in amdgpu_cs_parser_init() drm/amdgpu: Fix max_vblank_count value for current display engines drm/amdgpu: use kmemdup rather than duplicating its implementation drm/amdgpu: fix UVD suspend and resume for VI APU drm/amdgpu: fix the UVD suspend sequence order drm/amdgpu: make UVD handle checking more strict drm/amdgpu: Disable UVD PG drm/amdgpu: more scheduler cleanups v2 drm/amdgpu: cleanup fence queue init v2 drm/amdgpu: rename fence->scheduler to sched v2 drm/amdgpu: cleanup entity init drm/amdgpu: refine the scheduler job type conversion drm/amdgpu: refine the job naming for amdgpu_job and amdgpu_sched_job ...
2015-09-24drm/layerscape: fix handling fsl_dcu_drm_plane_index resultAndrzej Hajda
The function can return negative value. The problem has been detected using proposed semantic patch scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1]. [1]: http://permalink.gmane.org/gmane.linux.kernel/2038576 Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
2015-09-24drm/mgag200: Fix driver_load error handlingArchit Taneja
mgag200_driver_load's error path just calls the drm driver's driver_unload op. It isn't safe to call this because it doesn't handle things well if driver_load fails somewhere mid way. Replace the call to mgag200_driver_unload with a more finegrained error handling path. Link: http://lkml.kernel.org/r/55F6E68D.8070800@codeaurora.org Reported-by: Ingo Molnar <mingo@kernel.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dri-devel <dri-devel@lists.freedesktop.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
2015-09-24drm/mgag200: Fix error handling paths in fbdev driverArchit Taneja
Set up error handling in mgag200_fbdev_init and mgag200fb_create such that they release the things they allocate, rather than relying on someone calling mga_fbdev_destroy. Based on a patch by Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: http://lkml.kernel.org/r/55F6E68D.8070800@codeaurora.org Reported-by: Ingo Molnar <mingo@kernel.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dri-devel <dri-devel@lists.freedesktop.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
2015-09-24drm/qxl: only report first monitor as connected if we have no stateDave Airlie
If the server isn't new enough to give us state, report the first monitor as always connected, otherwise believe the server side. Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
2015-09-23net: davinci_emac: Add support for fixed-link PHYNeil Armstrong
In case the DaVinci Emac is directly connected to a non-mdio PHY/device, it should be possible to provide a fixed link configuration in the DT. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Driver: Vmxnet3: Extend register dump supportShrikrishna Khare
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Acked-by: Srividya Murali <smurali@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-09-22 This series contains updates to e1000, e1000e, igbvf, ixgbe, ixgbevf and fm10k. Jacob provides several updates for fm10k, which cleans up comments and most notably a fix for a corner case issue with the PF/VF mailbox code. The issue being fm10k_mbx_reset_work clears various states about the mailbox, but does not clear the Tx FIFO head/tail pointers. We also are not able to simply clear these pointers, as we would drop untransmitted messages without error. Also adds support for extra debug statistics, which provides the ability to see what the PF thinks the VF mailboxes look like. Don adds support for SFP+ in X550 and support for SCTP flow director filters SCTP mask. Francois Romieu dusts off the e1000 driver and removes some dead calls to e1000_init_eeprom_params(). Toshiaki Makita provides three patches to enable TSO for stacked VLAN's on e1000e, igbvf and ixgbevf. Mark provides the first of several ixgbe updates. First updates the driver to accept SFP not present error for all devices, since an SFP can still be inserted. Adds support for SFP insertion interrupt on X550EM devices with SPFs. Adds I2C combined operations on X550EM (not X550) devices. Moved the setting of lan_id to before any I2C eeprom access. Lastly, set the bit bang mode in the hardware when performing bit banding I2C operations on X550. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Dump contents of descriptor ring on TX timeoutDavid Woodhouse
We are seeing unexplained TX timeouts under heavy load. Let's try to get a better idea of what's going on. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Fix DMA unmapping of transmitted buffersDavid Woodhouse
The low 16 bits of the 'opts1' field in the TX descriptor are supposed to still contain the buffer length when the descriptor is handed back to us. In practice, at least on my hardware, they don't. So stash the original value of the opts1 field and get the length to unmap from there. There are other ways we could have worked out the length, but I actually want a stash of the opts1 field anyway so that I can dump it alongside the contents of the descriptor ring when we suffer a TX timeout. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Reduce duplicate csum/tso code in cp_start_xmit()David Woodhouse
We calculate the value of the opts1 descriptor field in three different places. With two different behaviours when given an invalid packet to be checksummed — none of them correct. Sort that out. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Fix TSO/scatter-gather descriptor setupDavid Woodhouse
When sending a TSO frame in multiple buffers, we were neglecting to set the first descriptor up in TSO mode. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Fix tx_queued debug message to print correct slot numbersDavid Woodhouse
After a certain amount of staring at the debug output of this driver, I realised it was lying to me. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-238139cp: Do not re-enable RX interrupts in cp_tx_timeout()David Woodhouse
If an RX interrupt was already received but NAPI has not yet run when the RX timeout happens, we end up in cp_tx_timeout() with RX interrupts already disabled. Blindly re-enabling them will cause an IRQ storm. (This is made particularly horrid by the fact that cp_interrupt() always returns that it's handled the interrupt, even when it hasn't actually done anything. If it didn't do that, the core IRQ code would have detected the storm and handled it, I'd have had a clear smoking gun backtrace instead of just a spontaneously resetting router, and I'd have at *least* two days of my life back. Changing the return value of cp_interrupt() will be argued about under separate cover.) Unconditionally leave RX interrupts disabled after the reset, and schedule NAPI to check the receive ring and re-enable them. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'netcp-fixes'David S. Miller
Murali Karicheri says: ==================== net: netcp: a set of bug fixes This patch series fixes a set of issues in netcp driver seen during internal testing of the driver. While at it, do some clean up as well. The fixes are tested on K2HK, K2L and K2E EVMs and the boot up logs can be seen at http://pastebin.ubuntu.com/12533100/ ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: fix deadlock reported by lockup detectorKaricheri, Muralidharan
A deadlock trace is seen in netcp driver with lockup detector enabled. The trace log is provided below for reference. This patch fixes the bug by removing the usage of netcp_modules_lock within ndo_ops functions. ndo_{open/close/ioctl)() is already called with rtnl_lock held. So there is no need to hold another mutex for serialization across processes on multiple cores. So remove use of netcp_modules_lock mutex from these ndo ops functions. ndo_set_rx_mode() shouldn't be using a mutex as it is called from atomic context. In the case of ndo_set_rx_mode(), there can be call to this API without rtnl_lock held from an atomic context. As the underlying modules are expected to add address to a hardware table, it is to be protected across concurrent updates and hence a spin lock is used to synchronize the access. Same with ndo_vlan_rx_add_vid() & ndo_vlan_rx_kill_vid(). Probably the netcp_modules_lock is used to protect the module not being removed as part of rmmod. Currently this is not fully implemented and assumes the interface is brought down before doing rmmod of modules. The support for rmmmod while interface is up is expected in a future patch set when additional modules such as pa, qos are added. For now all of the tests such as if up/down, reboot, iperf works fine with this patch applied. Deadlock trace seen with lockup detector enabled is shown below for reference. [ 16.863014] ====================================================== [ 16.869183] [ INFO: possible circular locking dependency detected ] [ 16.875441] 4.1.6-01265-gfb1e101 #1 Tainted: G W [ 16.881176] ------------------------------------------------------- [ 16.887432] ifconfig/1662 is trying to acquire lock: [ 16.892386] (netcp_modules_lock){+.+.+.}, at: [<c03e8110>] netcp_ndo_open+0x168/0x518 [ 16.900321] [ 16.900321] but task is already holding lock: [ 16.906144] (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4 [ 16.913206] [ 16.913206] which lock already depends on the new lock. [ 16.913206] [ 16.921372] [ 16.921372] the existing dependency chain (in reverse order) is: [ 16.928844] -> #1 (rtnl_mutex){+.+.+.}: [ 16.932865] [<c06023f0>] mutex_lock_nested+0x68/0x4a8 [ 16.938521] [<c04c5758>] register_netdev+0xc/0x24 [ 16.943831] [<c03e65c0>] netcp_module_probe+0x214/0x2ec [ 16.949660] [<c03e8a54>] netcp_register_module+0xd4/0x140 [ 16.955663] [<c089654c>] keystone_gbe_init+0x10/0x28 [ 16.961233] [<c000977c>] do_one_initcall+0xb8/0x1f8 [ 16.966714] [<c0867e04>] kernel_init_freeable+0x148/0x1e8 [ 16.972720] [<c05f9994>] kernel_init+0xc/0xe8 [ 16.977682] [<c0010038>] ret_from_fork+0x14/0x3c [ 16.982905] -> #0 (netcp_modules_lock){+.+.+.}: [ 16.987619] [<c006eab0>] lock_acquire+0x118/0x320 [ 16.992928] [<c06023f0>] mutex_lock_nested+0x68/0x4a8 [ 16.998582] [<c03e8110>] netcp_ndo_open+0x168/0x518 [ 17.004064] [<c04c48f0>] __dev_open+0xa8/0x10c [ 17.009112] [<c04c4b74>] __dev_change_flags+0x94/0x144 [ 17.014853] [<c04c4c3c>] dev_change_flags+0x18/0x48 [ 17.020334] [<c053a9fc>] devinet_ioctl+0x6dc/0x7e4 [ 17.025729] [<c04a59ec>] sock_ioctl+0x1d0/0x2a8 [ 17.030865] [<c0142844>] do_vfs_ioctl+0x41c/0x688 [ 17.036173] [<c0142ae4>] SyS_ioctl+0x34/0x5c [ 17.041046] [<c000ff60>] ret_fast_syscall+0x0/0x54 [ 17.046441] [ 17.046441] other info that might help us debug this: [ 17.046441] [ 17.054434] Possible unsafe locking scenario: [ 17.054434] [ 17.060343] CPU0 CPU1 [ 17.064862] ---- ---- [ 17.069381] lock(rtnl_mutex); [ 17.072522] lock(netcp_modules_lock); [ 17.078875] lock(rtnl_mutex); [ 17.084532] lock(netcp_modules_lock); [ 17.088366] [ 17.088366] *** DEADLOCK *** [ 17.088366] [ 17.094279] 1 lock held by ifconfig/1662: [ 17.098278] #0: (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4 [ 17.105774] [ 17.105774] stack backtrace: [ 17.110124] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 17.118637] Hardware name: Keystone [ 17.122123] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 17.129862] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 17.137079] [<c05ff450>] (dump_stack) from [<c0068e34>] (print_circular_bug+0x210/0x330) [ 17.145161] [<c0068e34>] (print_circular_bug) from [<c006ab7c>] (validate_chain.isra.35+0xf98/0x13ac) [ 17.154372] [<c006ab7c>] (validate_chain.isra.35) from [<c006da60>] (__lock_acquire+0x52c/0xcc0) [ 17.163149] [<c006da60>] (__lock_acquire) from [<c006eab0>] (lock_acquire+0x118/0x320) [ 17.171058] [<c006eab0>] (lock_acquire) from [<c06023f0>] (mutex_lock_nested+0x68/0x4a8) [ 17.179140] [<c06023f0>] (mutex_lock_nested) from [<c03e8110>] (netcp_ndo_open+0x168/0x518) [ 17.187484] [<c03e8110>] (netcp_ndo_open) from [<c04c48f0>] (__dev_open+0xa8/0x10c) [ 17.195133] [<c04c48f0>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 17.203129] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 17.211560] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 17.219729] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 17.227378] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 17.234939] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 17.242242] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 17.258855] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off [ 17.271282] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 17.279712] in_atomic(): 1, irqs_disabled(): 0, pid: 1662, name: ifconfig [ 17.286500] INFO: lockdep is turned off. [ 17.290413] Preemption disabled at:[< (null)>] (null) [ 17.295728] [ 17.297214] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 17.305735] Hardware name: Keystone [ 17.309223] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 17.316970] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 17.324194] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 17.332112] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 17.340724] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>] (dev_set_rx_mode+0x1c/0x28) [ 17.348982] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>] (__dev_open+0xc4/0x10c) [ 17.356724] [<c04c490c>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 17.364729] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 17.373166] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 17.381344] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 17.388994] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 17.396563] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 17.403873] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 17.413772] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.20.2) started Sending discover... [ 18.690666] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off Sending discover... [ 22.250972] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off [ 22.258721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.265458] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 22.273896] in_atomic(): 1, irqs_disabled(): 0, pid: 342, name: kworker/1:1 [ 22.280854] INFO: lockdep is turned off. [ 22.284767] Preemption disabled at:[< (null)>] (null) [ 22.290074] [ 22.291568] CPU: 1 PID: 342 Comm: kworker/1:1 Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 22.300255] Hardware name: Keystone [ 22.303750] Workqueue: ipv6_addrconf addrconf_dad_work [ 22.308895] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 22.316643] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 22.323867] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 22.331786] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 22.340394] [<c03e9840>] (netcp_set_rx_mode) from [<c04c9d18>] (__dev_mc_add+0x54/0x68) [ 22.348401] [<c04c9d18>] (__dev_mc_add) from [<c05ab358>] (igmp6_group_added+0x168/0x1b4) [ 22.356580] [<c05ab358>] (igmp6_group_added) from [<c05ad2cc>] (ipv6_dev_mc_inc+0x4f0/0x5a8) [ 22.365019] [<c05ad2cc>] (ipv6_dev_mc_inc) from [<c058f0d0>] (addrconf_dad_work+0x21c/0x33c) [ 22.373460] [<c058f0d0>] (addrconf_dad_work) from [<c0042850>] (process_one_work+0x214/0x8d0) [ 22.381986] [<c0042850>] (process_one_work) from [<c0042f54>] (worker_thread+0x48/0x4bc) [ 22.390071] [<c0042f54>] (worker_thread) from [<c004868c>] (kthread+0xf0/0x108) [ 22.397381] [<c004868c>] (kthread) from [<c0010038>] Trace related to incorrect usage of mutex inside ndo_set_rx_mode [ 24.086066] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 24.094506] in_atomic(): 1, irqs_disabled(): 0, pid: 1682, name: ifconfig [ 24.101291] INFO: lockdep is turned off. [ 24.105203] Preemption disabled at:[< (null)>] (null) [ 24.110511] [ 24.112005] CPU: 2 PID: 1682 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 24.120518] Hardware name: Keystone [ 24.124018] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 24.131772] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 24.138989] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 24.146908] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 24.155523] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>] (dev_set_rx_mode+0x1c/0x28) [ 24.163787] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>] (__dev_open+0xc4/0x10c) [ 24.171531] [<c04c490c>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 24.179528] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 24.187966] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 24.196145] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 24.203803] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 24.211373] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 24.218676] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 24.227156] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: allocate buffers to desc before re-enable interruptKaricheri, Muralidharan
Currently netcp_rxpool_refill() that refill descriptors and attached buffers to fdq while interrupt is enabled as part of NAPI poll. Doing it while interrupt is disabled could be beneficial as hardware will not be starved when CPU is busy with processing interrupt. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: check for interface handle in netcp_module_probe()Karicheri, Muralidharan
Currently netcp_module_probe() doesn't check the return value of of_parse_phandle() that points to the interface data for the module and then pass the node ptr to the module which is incorrect. Check for return value and free the intf_modpriv if there is error. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: add error check to netcp_allocate_rx_buf()Karicheri, Muralidharan
Currently, if netcp_allocate_rx_buf() fails due no descriptors in the rx free descriptor queue, inside the netcp_rxpool_refill() function the iterative loop to fill buffers doesn't terminate right away. So modify the netcp_allocate_rx_buf() to return an error code and use it break the loop when there is error. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: move netcp_register_interface() to after attach moduleKaricheri, Muralidharan
The netcp interface is not fully initialized before attach the module to the interface. For example, the tx pipe/rx pipe is initialized in ethss module as part of attach(). So until this is complete, the interface can't be registered. So move registration of interface to net device outside the current loop that attaches the modules to the interface. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: remove dead code from the driverKaricheri, Muralidharan
netcp_core is the first driver that will get initialized and the modules (ethss, pa etc) will then get initialized. So the code at the end of netcp_probe() that iterate over the modules is a dead code as the module list will be always be empty. So remove this code. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: netcp: ethss: fix error in calling sgmii api with incorrect offsetWingMan Kwok
On K2HK, sgmii module registers of slave 0 and 1 are mem mapped to one contiguous block, while those of slave 2 and 3 are mapped to another contiguous block. However, on K2E and K2L, sgmii module registers of all slaves are mem mapped to one contiguous block. SGMII APIs expect slave 0 sgmii base when API is invoked for slave 0 and 1, and slave 2 sgmii base when invoked for other slaves. Before this patch, slave 0 sgmii base is always passed to sgmii API for K2E regardless which slave is the API invoked for. This patch fixes the problem. Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'bridge_external_fdb_aging'David S. Miller
Scott Feldman says: ==================== bridge: don't age out externally added FDB entries v3: Per davem review: add del_timer_sync on rocker port remove. v2: Per Jiri review comment: add BR_DEFAULT_AGEING_TIME to defines Siva originally proposed skipping externally added FDB entries in the bridge's FDB garbage collection func, and moving the ageing of externally added entries to the port driver/device. This broke rocker, since rocker didn't have a hardware (or software) mechanism for ageing out its learned FDB entries. This patchset reintroduces Siva's bridge driver patch to skip externally added entries and adds support in rocker so rocker can age out its own entries. Rocker does this using a software timer similar to the bridge's FDB garbage collection timer. Other switchdev devices/drivers can use this software timer method or program the device to nofity aged-out entries to the driver. Updated switchdev.txt documentation to reflect current state-of-the-art. This removes one more XXX todo comment in switchdev.txt. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23switchdev: update documentation on FDB ageing_timeScott Feldman
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23bridge: don't age externally added FDB entriesSiva Mannem
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Premkumar Jonnala <pjonnala@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: add FDB cleanup timerScott Feldman
Add a timer to each rocker switch to do FDB entry cleanup by ageing out expired entries. The timer scheduling algo is copied from the bridge driver, for the most part, to keep the firing of the timer to a minimum. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: adding port ageing_time for ageing out FDB entriesScott Feldman
Follow-up patcheset will allow user to change ageing_time, but for now just hard-code it to a fixed value (the same value used as the default for the bridge driver). Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23bridge: define some min/max/default ageing time constantsScott Feldman
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: store rocker_port in fdb key rather than pportScott Feldman
We'll need more info from rocker_port than just pport when we age out fdb entries, so store rocker_port rather than pport in each fdb entry. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: track when FDB entry is touched.Scott Feldman
The entry is touched once when created, and touched again for each update. The touched time is used to calculate FDB entry age. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Fix AF_PACKET ABI breakage in 4.2David Woodhouse
Commit 7d82410950aa ("virtio: add explicit big-endian support to memory accessors") accidentally changed the virtio_net header used by AF_PACKET with PACKET_VNET_HDR from host-endian to big-endian. Since virtio_legacy_is_little_endian() is a very long identifier, define a vio_le macro and use that throughout the code instead of the hard-coded 'false' for little-endian. This restores the ABI to match 4.1 and earlier kernels, and makes my test program work again. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23netpoll: Close race condition between poll_one_napi and napi_disableNeil Horman
Drivers might call napi_disable while not holding the napi instance poll_lock. In those instances, its possible for a race condition to exist between poll_one_napi and napi_disable. That is to say, poll_one_napi only tests the NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such the following may happen: CPU0 CPU1 ndo_tx_timeout napi_poll_dev napi_disable poll_one_napi test_and_set_bit (ret 0) test_bit (ret 1) reset adapter napi_poll_routine If the adapter gets a tx timeout without a napi instance scheduled, its possible for the adapter to think it has exclusive access to the hardware (as the napi instance is now scheduled via the napi_disable call), while the netpoll code thinks there is simply work to do. The result is parallel hardware access leading to corrupt data structures in the driver, and a crash. Additionaly, there is another, more critical race between netpoll and napi_disable. The disabled napi state is actually identical to the scheduled state for a given napi instance. The implication being that, if a napi instance is disabled, a netconsole instance would see the napi state of the device as having been scheduled, and poll it, likely while the driver was dong something requiring exclusive access. In the case above, its fairly clear that not having the rings in a state ready to be polled will cause any number of crashes. The fix should be pretty easy. netpoll uses its own bit to indicate that that the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC). We can just gate disabling on that bit as well as the sched bit. That should prevent netpoll from conducting a napi poll if we convert its set bit to a test_and_set_bit operation to provide mutual exclusion Change notes: V2) Remove a trailing whtiespace Resubmit with proper subject prefix V3) Clean up spacing nits Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> CC: jmaxwell@redhat.com Tested-by: jmaxwell@redhat.com Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'cls_bpf-next'David S. Miller
Daniel Borkmann says: ==================== Minor cls_bpf updates Some minor updates resp. follow-ups on cls_bpf, please see individual patches for details. Will follow with the iproute2 patch after this series. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: further limit exec opcodes subsetDaniel Borkmann
Jamal suggested to further limit the currently allowed subset of opcodes that may be used by a direct action return code as the intention is not to replace the full action engine, but rather to have a minimal set that can be used in the fast-path on things like ingress for some features that cls_bpf supports. Classifiers can, of course, still be chained together that have direct action mode with those that have a full exec pass. For more complex scenarios that go beyond this minimal set here, the full tcf_exts_exec() path must be used. Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: make binding to classid optionalDaniel Borkmann
The binding to a particular classid was so far always mandatory for cls_bpf, but it doesn't need to be. Therefore, lift this restriction as similarly done in other classifiers. Only a couple of qdiscs make use of class from the tcf_result, others don't strictly care, so let the user choose his needs (those that read out class can handle situations where it could be NULL). An explicit check for tcf_unbind_filter() is also not needed here, as the previous r->class was 0, so the xchg() will return that and therefore a callback to the qdisc's unbind_tcf() is skipped. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: also dump TCA_BPF_FLAGSDaniel Borkmann
In commit 43388da42a49 ("cls_bpf: introduce integrated actions") we have added TCA_BPF_FLAGS. We can also retrieve this information from the prog, dump it back to user space as well. It's useful in tc when displaying/dumping filter info. Also, remove tp from cls_bpf_prog_from_efd(), came in as a conflict from a rebase and it's unused here (later work may add it along with a real user). Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge tag 'arcnet-cleanup-v4.3-rc2' of git://git.pengutronix.de/git/mgr/linuxDavid S. Miller
Michael Grzeschik says: ==================== ARCNET: refactoring and cleanup This series cleans up the code in drivers/net/arcnet and include/uapi/linux/if_arcnet.h . It doesn't change the runtime behaviour of the code. Its only purpose is to improve the code maintenance and readability. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-31 02:11:18 +0000