| Age | Commit message (Collapse) | Author |
|---|
|
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is
required for multicast routing.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Spectrum-2, MC routing is implemented using ACL block explicitly, so
router initialization should take place after ACL initialization.
Set the initialization of the ACL block before IP router initizalization
takes place, so multicast router will be able to allocate ACL data
structures and create its required chains.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to schedule a different tasklet for refill,
This patch remove it.
Suggested-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor markup fixup from bpf-next into net-next merge in the BPF helper
description of bpf_sk_lookup_tcp() and bpf_sk_lookup_udp(). Also sync
up the copy of bpf.h from tooling infrastructure.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding and removing neighbor entries to / from the gc_list need to be
done while holding the table lock; a couple of places were missed in the
original patch.
Move the list_add_tail in neigh_alloc to ___neigh_create where the lock
is already obtained. Since neighbor entries should rarely be moved
to/from PERMANENT state, add lock/unlock around the gc_list changes in
neigh_change_state rather than extending the lock hold around all
neighbor updates.
Fixes: 58956317c8de ("neighbor: Improve garbage collection")
Reported-by: Andrei Vagin <avagin@gmail.com>
Reported-by: syzbot+6cc2fd1d3bdd2e007363@syzkaller.appspotmail.com
Reported-by: syzbot+35e87b87c00f386b041f@syzkaller.appspotmail.com
Reported-by: syzbot+b354d1fb59091ea73c37@syzkaller.appspotmail.com
Reported-by: syzbot+3ddead5619658537909b@syzkaller.appspotmail.com
Reported-by: syzbot+424d47d5c456ce8b2bbe@syzkaller.appspotmail.com
Reported-by: syzbot+e4d42eb35f6a27b0a628@syzkaller.appspotmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5e-updates-2018-12-10 (gre)
This patch set adds GRE offloading support to Mellanox ethernet driver.
Patches 1-5 replace the existing egdev mechanism with the new TC indirect
block binds mechanism that was introduced by Netronome:
7f76fa36754b ("net: sched: register callbacks for indirect tc block binds")
Patches 6-9 add GRE offloading support along with some required
refactoring work.
Patch 10, Add netif_is_gretap()/netif_is_ip6gretap()
- Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
Patch 11, add GRE offloading support to mlx5.
Patch 12 removes the egdev mechanism from TC as it is no longer used by
any of the drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The egdev mechanism was replaced by the TC indirect block notifications
platform.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add HW offloading support for TC flower filters configured on
gretap/ip6gretap net devices.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
This approach aligns with the current identification methods and function
names of vxlan and geneve network devices.
Convert mlxsw to use these helpers and use them in downstream mlx5 patch.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move tunnel offloading related code to a separate source file for better
code maintainability.
Code refactoring with no functional change.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the tunnel offloading encap/decap methods assumes that VXLAN
is the sole tunneling protocol. Lay the infrastructure for supporting
multiple tunneling protocols by branching according to the tunnel
net device kind.
Encap filters tunnel type is determined according to the egress/mirred
net device. Decap filters classify the tunnel type according to the
filter's ingress net device kind.
Distinguish between the tunnel type as defined by the SW model and
the FW reformat type that specifies the HW operation being made.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Separates the vxlan header match handling from the matching on the
general fields of ipv4/6 tunnels, thus allowing the common IP tunnel
match code to branch in down stream patch, to multiple IP tunnels.
This patch doesn't add any functionality.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Separates the vxlan header encap logic from the general ipv4/6
encapsulation methods, thus allowing the common IP encap/decap code to
branch in downstream patch to multiple IP tunnels.
Code refactoring with no functional change.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use TC indirect block notifications to offload filters that
are configured on higher level device interfaces (e.g. tunnel
devices). This mechanism replaces the current egdev implementation.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Propagate the filter's net_device parameter to the tc flower parsed
attributes structure so that it can later be used in tunnel decap
offloading sequences.
Pre-step for replacing egdev logic with the indirect block
notification mechanism.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the driver controls flower filters that are installed on its
devices. However, with the introduction of the indirect block
notifications platform the driver may receive control events for filters
that are installed on higher level net devices (e.g. tunnel devices).
Therefore, the driver filter control API will not be able to implicitly
assume the filter's net device.
Explicitly specify the filter's net device, no functional change
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Towards using this mechanism as the means to offload tunnel decap rules
set on SW tunnel devices instead of egdev, add the supporting structures
and functions.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently only a single field in the representor private structure
is relevant for uplink representors. As a pre-step to allow adding
additional uplink representor fields, introduce uplink representor
private structure.
This is prepration step towards replacing egdev logic with the
indirect block notification mechanism. This patch doesn't change
any functionality.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) RDMA ODP (On Demand Paging) improvements and moving ODP logic to
mlx5 RDMA driver
2) Improved mlx5 core driver and device events handling and provided API
for upper layers to subscribe to device events.
3) RDMA only code cleanup from mlx5 core
4) Add helper to get CQE opcode
5) Rework handling of port module events
6) shared mlx5_ifc.h updates to avoid conflicts
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Yonghong Song says:
====================
Before func_info and line_info are added to the kernel, there are several
fields in structure bpf_prog_info specifying the "count" of a user buffer, e.g.,
__u32 nr_jited_ksyms;
__u32 nr_jited_func_lens;
The naming convention has the prefix "nr_".
The func_info and line_info support added several fields
__u32 func_info_cnt;
__u32 line_info_cnt;
__u32 jited_line_info_cnt;
to indicate the "count" of buffers func_info, line_info and jited_line_info.
The original intention is to keep the field names the same as those in
structure bpf_attr, so it will be clear that the "count" returned to user
space will be the same as the one passed to the kernel during prog load.
Unfortunately, the field names *_info_cnt are not consistent with
other existing fields in bpf_prog_info.
This patch set renamed the fields *_info_cnt to nr_*_info
to keep naming convention consistent.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Rename all occurances of *_info_cnt field access
to nr_*_info in tools directory.
The local variables finfo_cnt, linfo_cnt and jited_linfo_cnt
in function do_dump() of tools/bpf/bpftool/prog.c are also
changed to nr_finfo, nr_linfo and nr_jited_linfo to
keep naming convention consistent.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Sync kernel uapi bpf.h "*_info_cnt => nr_*_info"
changes to tools directory.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In uapi bpf.h, currently we have the following fields in
the struct bpf_prog_info:
__u32 func_info_cnt;
__u32 line_info_cnt;
__u32 jited_line_info_cnt;
The above field names "func_info_cnt" and "line_info_cnt"
also appear in union bpf_attr for program loading.
The original intention is to keep the names the same
between bpf_prog_info and bpf_attr
so it will imply what we returned to user space will be
the same as what the user space passed to the kernel.
Such a naming convention in bpf_prog_info is not consistent
with other fields like:
__u32 nr_jited_ksyms;
__u32 nr_jited_func_lens;
This patch made this adjustment so in bpf_prog_info
newly introduced *_info_cnt becomes nr_*_info.
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
info.nr_jited_ksyms and info.nr_jited_func_lens cannot be 0 in these two
statements, so we don't need to check them.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This isn't used anywhere across the mlx5 driver stack,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update the flow steering command formatting according to the extended
destination API.
Note that the FW dictates that multi destination FTEs that involve at
least one encap must use the extended destination format, while single
destination ones must use the legacy format.
Using extended destination format requires FW support. Check for its
capabilities and return error if not supported.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Change the driver flow destination struct to use bit flags with the vhca
id valid being the 1st one. The flags field is more extendable and will
be used in downstream patch.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Extended destinations provide the ability to configure different
encapsulation properties per destination on a single FTE. This is
needed for use-cases such as remote mirroring over tunneled networks.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit
key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l).
Define the two key parsing alternatives in a union, thus enabling both
access methods.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support a new hardware module status in port module events:
- module_status=0x4 (Cable plugged, but disabled)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support a new hardware error type in port module events:
- error_type=0xc (PCIe system power slot exceeded)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add explicit HW defined error values. For simplicity, keep counters for all
statuses starting from 0, although currently status=0 is not used.
Additionally, when HW signals an unexpected cable status, it is reported
now rather than ignored. And status counter is now updated on errors.
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch fixes a few newline issues and also
replaces p_err with p_info in prog.c
Fixes: b053b439b72a ("bpf: libbpf: bpftool: Print bpf_line_info during prog dump")
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In commit f9bfe4e6a9d0 ("tcp: lack of available data can also cause
TSO defer") we moved the test in tcp_tso_should_defer() for packets
with a FIN flag, and we mentioned that the same would be done
later for EOR flag.
Both flags should be handled at the same time, after all other
heuristics have been considered. They both mean that no more bytes
can be added to this skb by an application.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek Vasut says:
====================
net: dsa: ksz: Add reset GPIO handling
Add code to handle optional reset GPIO in the KSZ switch driver and a
matching DT property adjustments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add optional reset GPIO, as such a signal is available on the KSZ switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following gcc warning:
drivers/net/ipvlan/ipvlan_main.c:543:12: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'mode' is a u16 variable, IPVLAN_MODE_L2 is zero,
the comparison is always false
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a msg string, fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
