| Age | Commit message (Collapse) | Author |
|---|
|
Calls to set_memory_wb() incure heavy TLB flush and IPI cost. To
minimize those wait until pool grow beyond batch size before
draining the pool.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-and-Tested-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Current code never allowed the page pool to actualy fill in anyway.
This fix it, so that we only start freeing page from the pool when
we go over the pool size.
Changed since v1:
- Move the page batching optimization to its separate patch.
Changed since v2:
- Do not remove code part of the batching optimization with
this patch.
- Better commit message.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-and-Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Time to light a candle and remove the preliminary_hw_support flag.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
on SKL/BXT, the top most plane hardware is shared between the legacy
cursor registers and an actual plane. Daniel and Ville don't want to
expose 2 DRM planes and would rather expose a CURSOR plane that has all
the usual plane properties, and that's a blocker for lifting the
prelimary_hw_support flag.
Unfortunately noone has had the time to finish this yet, but lifting the
prelimary_hw_support flag is long overdue. As an intermediate solution
we can merely not expose the top most plane
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Fix divide by zero if we end up updating the watermarks
with zero dotclock.
This is a stop gap measure to allow module load in cases
where our state keeping fails.
v2: WARN_ON added (Paulo)
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ttm_bo_validate() returns 0 or error. So we can return the value
directly and remove the variable 'ret'.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These variables were assigned some values but they were never used.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two bugs in the cpufreq core (including one recent
regression), fix a 4.0 PCI regression related to the ACPI resources
management and quieten an RCU-related lockdep complaint about a
tracepoint in the suspend-to-idle code.
Specifics:
- Fix a recently introduced issue in the cpufreq policy object
reinitialization that leads to CPU offline/online breakage (Viresh
Kumar)
- Make it possible to access frequency tables of offline CPUs which
is needed by thermal management code among other things (Viresh
Kumar)
- Fix an ACPI resource management regression introduced during the
4.0 cycle that may cause incorrect resource validation results to
appear in 32-bit x86 kernels due to silent truncation of 64-bit
values to 32-bit (Jiang Liu)
- Fix up an RCU-related lockdep complaint about suspicious RCU usage
in idle caused by using a suspend tracepoint in the core suspend-
to-idle code (Rafael J Wysocki)"
* tag 'pm+acpi-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix SMBIOS call handling and hwswitch state coherency in the
dell-laptop driver. Cleanups for intel_*_ipc drivers. Details:
dell-laptop:
- Do not cache hwswitch state
- Check return value of each SMBIOS call
- Clear buffer before each SMBIOS call
intel_scu_ipc:
- Move local memory initialization out of a mutex
intel_pmc_ipc:
- Update kerneldoc formatting
- Fix compiler casting warnings"
* tag 'platform-drivers-x86-v4.2-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_scu_ipc: move local memory initialization out of a mutex
intel_pmc_ipc: Update kerneldoc formatting
dell-laptop: Do not cache hwswitch state
dell-laptop: Check return value of each SMBIOS call
dell-laptop: Clear buffer before each SMBIOS call
intel_pmc_ipc: Fix compiler casting warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu/coldfire fixes from Greg Ungerer:
"Contains build fixes and updates for the ColdFire defconfigs.
Specifically there is a couple of fixes that address problems building
allnoconfig. Also fix for enabling PCI bus on the M54xx family of
ColdFire"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: enable PCI support for m5475evb defconfig
m68k: fix io functions for ColdFire/MMU/PCI case
m68knommu: update defconfig for ColdFire m5475evb
m68knommu: update defconfig for ColdFire m5407c3
m68knommu: update defconfig for ColdFire m5307c3
m68knommu: update defconfig for ColdFire m5275evb
m68knommu: update defconfig for ColdFire m5272c3
m68knommu: update defconfig for ColdFire m5249evb
m68knommu: update defconfig for m5208evb
m68knommu: make ColdFire SoC selection a choice
m68knommu: improve the clock configuration defaults
m68knommu: force setting of CONFIG_CLOCK_FREQ for ColdFire
|
|
If no work was performed then prealloc_data_structs() wasn't ever called
so there isn't any need to call prealloc_free_structs().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Refactor writeback_some_dirty_blocks() to avoid prealloc_data_structs()
if the policy doesn't have any dirty blocks ready for writeback.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
All methods that queue work call wake_worker() as you'd expect.
E.g. cell_defer, defer_bio, quiesce_migration (which is called by
writeback, promote, demote_then_promote, invalidate, discard, etc).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
misc rockchip fixes.
* 'drm-rockchip-2015-07-13' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: vop: remove hardware cursor window
drm/rockchip: vop: switch cursor plane to window 3
drm/rockchip: Drop owner assignment from platform_driver
drm/rockchip: use drm_gem_mmap helpers
drm/rockchip: only call drm_fb_helper_hotplug_event if fb_helper present
drm/rockchip: Add BGR formats to VOP
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: fixes for parallel-display, imx-tve, and ipu-common
These patches fix the parallel-display driver to use the standard OF
graph bindings for connecting a drm_panel via device tree instead of
an undocumented, driver specific device tree property, take care to
disable all IPU interrupts before setting up the irq chip to fix a
kexec lockup, and fix VGA output on i.MX53-QSB boards by correcting
the media bus format set by the imx-tve driver.
* tag 'imx-drm-fixes-2015-07-14' of git://git.pengutronix.de/git/pza/linux:
drm/imx: tve: fix media bus format for VGA output
GPU: ipu: fix lockup caused by pending chained interrupts
drm/imx: parallel-display: fix drm_panel support
|
|
into drm-fixes
A range of fixes for the Armada DRM driver:
- A missing wakeup could result in overlay frames being delayed, causing
video playback to hiccup.
- Avoid unmapping a dma-buf attachment which was never mapped
- Fix the overlay when partially off the screen by switching to the
drm_plane_helper_check_update() helper and using the calculated
coordinates to set the start address.
- Remove an incorrect assignment to crtc->mode - which should be the
unadjusted mode.
- Fix a missing call to drm_plane_cleanup() in the overlay code.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: avoid saving the adjusted mode to crtc->mode
drm/armada: fix overlay when partially off-screen
drm/armada: convert overlay to use drm_plane_helper_check_update()
drm/armada: fix gem object free after failed prime import
drm/armada: fix incorrect overlay plane cleanup
drm/armada: fix missing overlay wake-up
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Next batch of i915 fixes. Note that the compat32 patch here needs the drm
core one to be actually useful, I'll send you that one with a separate
drm-fixes pull request. One revert because a fix in -rc2 did break
existing userspace.
* tag 'drm-intel-fixes-2015-07-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Do not call intel_crtc_disable if the crtc is already disabled.
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
drm/i915: Forward all core DRM ioctls to core compat handling
drm/i915: fix oops in primary_check_plane
drm/i915: remove unused has_dma_mapping flag
drm/i915: Fix missing return warning for !CONFIG_DEBUGFS
drm/i915: avoid leaking DMA mappings
drm/i915: Snapshot seqno of most recently submitted request.
drm/i915: Store device pointer in contexts for late tracepoint usafe
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Ok next attempt at drm-fixes pull. Big thing really is just the compat32
one for addfb2.1.
* tag 'topic/drm-fixes-2015-07-16' of git://anongit.freedesktop.org/drm-intel:
drm: Provide compat ioctl for addfb2.1
Documentation: drm: Fix tablulation in KMS properties table
drm: add a check for x/y in drm_mode_setcrtc
drm/rockchip: use drm_gem_mmap helpers
|
|
into drm-fixes
More radeon and amdgpu fixes for 4.2. Mostly amdgpu bug fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/dce8: Re-set VBLANK interrupt state when enabling a CRTC
drm/radeon/ci: silence a harmless PCC warning
drm/amdgpu/cz: silence some dpm debug output
drm/amdgpu/cz: store the forced dpm level
drm/amdgpu/cz: unforce dpm levels before forcing to low/high
drm/amdgpu: remove bogus check in gfx8 rb setup
drm/amdgpu: set proper index/data pair for smc regs on CZ (v2)
drm/amdgpu: disable the IP module if early_init returns -ENOENT (v2)
drm/amdgpu: stop context leak in the error path
drm/amdgpu: validate the context id in the dependencies
drm/radeon: fix user ptr race condition
drm/radeon: Don't flush the GART TLB if rdev->gart.ptr == NULL
drm/radeon: add a dpm quirk for Sapphire Radeon R9 270X 2GB GDDR5
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes from the last few weeks that should go into the
current series. This contains:
- Various fixes for the per-blkcg policy data, fixing regressions
since 4.1. From Arianna and Tejun
- Code cleanup for bcache closure macros from me. Really just
flushing this out, it's been sitting in another branch for months
- FIELD_SIZEOF cleanup from Maninder Singh
- bio integrity oops fix from Mike
- Timeout regression fix for blk-mq from Ming Lei"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: set default timeout as 30 seconds
NVMe: Reread partitions on metadata formats
bcache: don't embed 'return' statements in closure macros
blkcg: fix blkcg_policy_data allocation bug
blkcg: implement all_blkcgs list
blkcg: blkcg_css_alloc() should grab blkcg_pol_mutex while iterating blkcg_policy[]
blkcg: allow blkcg_pol_mutex to be grabbed from cgroup [file] methods
block/blk-cgroup.c: free per-blkcg data when freeing the blkcg
block: use FIELD_SIZEOF to calculate size of a field
bio integrity: do not assume bio_integrity_pool exists if bioset exists
|
|
Pull jfs fixes from David Kleikamp:
"A couple trivial fixes and an error path fix"
* tag 'jfs-4.2' of git://github.com/kleikamp/linux-shaggy:
jfs: clean up jfs_rename and fix out of order unlock
jfs: fix indentation on if statement
jfs: removed a prohibited space after opening parenthesis
|
|
Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.
So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
|
|
Since dm9000 driver added support for a vcc regulator, platform data
based platforms have their ethernet broken, as the regulator claiming
returns -EPROBE_DEFER and prevents dm9000 loading.
This patch fixes this for all pxa boards using dm9000, by using the
specific regulator_has_full_constraints() function.
This was discovered and tested on the cm-x300 board.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Something (ATOM BIOS?) seems to be clobbering the LB_INTERRUPT_MASK
register while the CRTC is off, which caused e.g. glxgears or
gnome-shell to hang after a modeset.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
|
|
This has been a source of confusion. Make it debug only.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
So the selected forced level shows up properly in sysfs.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is necessary to properly reset the min/max limits before
clamping them otherwise we may get improper clamping depending
on what what was the last forced level.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Always respect the harvest configuration as is.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
v2: squash in later fix
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If we run into a part with a harvest configuration where the entire
IP block is unusable, just disable the IP block.
v2: fix logic as noted by Christian
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
|
|
Just to make sure userspace don't send nonsense to the kernel.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
|
|
Port of amdgpu patch 9298e52f8b51d1e4acd68f502832f3a97f8cf892.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This can be the case when the GPU is powered off, e.g. via vgaswitcheroo
or runpm. When the GPU is powered up again, radeon_gart_table_vram_pin
flushes the TLB after setting rdev->gart.ptr to non-NULL.
Fixes panic on powering off R7xx GPUs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61529
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Universal planes may not be assigned to the current crtc, so only
update crtc->x/y when the primary is part of the state and bound
to the current crtc.
Changes since v1:
- Add the crtc check.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
It is reasonable to set default timeout of request as 30 seconds instead of
30000 ticks, which may be 300 seconds if HZ is 100, for example, some arm64
based systems may choose 100 HZ.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Fixes: c76cbbcf4044 ("blk-mq: put blk_queue_rq_timeout together in blk_mq_init_queue()"
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
There is currently no way to see that the needs_check flag has been set
in the metadata. Display 'needs_check' in the cache status if it is set
in the cache metadata.
Also, update cache documentation.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
There is currently no way to see that the needs_check flag has been set
in the metadata. Display 'needs_check' in the thin-pool status if it is
set in the thinp metadata.
Also, update thinp documentation.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
This fixes an issue where running out of data space would cause the
thin-pool's metadata to become read-only. There was no reason to make
metadata read-only -- calling set_pool_mode() with PM_READ_ONLY was a
misguided way to error all queued and future write IOs. We can
accomplish the same by degrading from PM_OUT_OF_DATA_SPACE to
PM_OUT_OF_DATA_SPACE with error_if_no_space enabled.
Otherwise, the use of PM_READ_ONLY could cause a race where commit() was
started before the PM_READ_ONLY transition but dm_pool_commit_metadata()
would go on to fail because the block manager had transitioned to
read-only. The return of -EPERM from dm_pool_commit_metadata(), due to
attempting to commit while in read-only mode, caused the thin-pool to
set 'needs_check' because a metadata_operation_failed(). This needless
cascade of failures makes life for users more difficult than needed.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Commit 1e6f2416044c0 changed the scsi sysfs 'queue_depth' code to
rejects depths higher than the scsi host template setting. But lots
of hosts set this to 1, and update the settings in the scsi host
when the controller/devices probing happens.
This breaks (at least) mpt2sas and mpt3sas runtime setting of queue
depth, returning EINVAL for all settings but '1'. And once it's set to
1, there's no way to go back up.
Cc: stable@vger.kernel.org
Fixes: 1e6f2416044c0 "scsi: don't allow setting of queue_depth bigger than can_queue"
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
pca953x interrupt controller functionality is implemented using
nested threaded IRQs which require parent_irq to be configured
properly otherwise below warning can be seen if IRQ core
will try re-schedule nested IRQ:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 12 at kernel/irq/manage.c:696 irq_nested_primary_handler+0x30/0x38()
Primary handler called for nested irq 301
Modules linked in: uinput ipv6 smsc95xx usbnet mii imx2_wdt etnaviv(C) matrix_keypad matrix_keymap ar1021_i2c
CPU: 1 PID: 12 Comm: ksoftirqd/1 Tainted: G WC 4.1.1 #9
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c0013298>] (dump_backtrace) from [<c0013488>] (show_stack+0x20/0x24)
[<c0013468>] (show_stack) from [<c05743c4>] (dump_stack+0x70/0xc0)
[<c0574354>] (dump_stack) from [<c002b7b8>] (warn_slowpath_common+0x88/0xc0)
[<c002b730>] (warn_slowpath_common) from [<c002b8ac>] (warn_slowpath_fmt+0x40/0x48)
[<c002b870>] (warn_slowpath_fmt) from [<c0075798>] (irq_nested_primary_handler+0x30/0x38)
[<c0075768>] (irq_nested_primary_handler) from [<c0075200>] (handle_irq_event_percpu+0x70/0x2d0)
[<c0075190>] (handle_irq_event_percpu) from [<c00754ac>] (handle_irq_event+0x4c/0x6c)
[<c0075460>] (handle_irq_event) from [<c0078204>] (handle_simple_irq+0xa4/0xc8)
[<c0078160>] (handle_simple_irq) from [<c0077cd4>] (resend_irqs+0x50/0x7c)
[<c0077c84>] (resend_irqs) from [<c002f99c>] (tasklet_action+0x94/0x140)
[<c002f908>] (tasklet_action) from [<c002eea8>] (__do_softirq+0xa0/0x3c8)
[<c002ee08>] (__do_softirq) from [<c002f208>] (run_ksoftirqd+0x38/0x54)
[<c002f1d0>] (run_ksoftirqd) from [<c004b1e4>] (smpboot_thread_fn+0x1f8/0x2f0)
[<c004afec>] (smpboot_thread_fn) from [<c0047744>] (kthread+0xe8/0x104)
[<c004765c>] (kthread) from [<c000fac8>] (ret_from_fork+0x14/0x2c)
---[ end trace 96052cda48865769 ]---
The issue was reported and described in details by Lothar Waßmann and
Christian Gmeiner in https://lkml.org/lkml/2014/9/9/123.
Fix it by adding missed call of gpiochip_set_chained_irqchip()
so GPIO IRQ chip helpers will set parent_irq for nested IRQs
properly.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Two SLES11 SP3 servers encountered similar crashes simultaneously
following some kind of SAN/tape target issue:
...
qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002.
qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002.
qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2.
qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2.
qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps).
qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2.
qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000.
rport-3:0-0: blocked FC remote port time out: removing target and saving binding
qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps).
qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2.
rport-2:0-0: blocked FC remote port time out: removing target and saving binding
sg_rq_end_io: device detached
BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8
IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP
CPU 0
...
Supported: No, Proprietary modules are loaded [1739975.390463]
Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8
RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138
RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0
R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001
R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80
FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640)
Stack:
ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80
ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000
ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e
Call Trace:
[<ffffffffa03fa309>] st_open+0x129/0x240 [st]
[<ffffffff8115ea1e>] chrdev_open+0x13e/0x200
[<ffffffff811588a8>] __dentry_open+0x198/0x310
[<ffffffff81167d74>] do_last+0x1f4/0x800
[<ffffffff81168fe9>] path_openat+0xd9/0x420
[<ffffffff8116946c>] do_filp_open+0x4c/0xc0
[<ffffffff8115a00f>] do_sys_open+0x17f/0x250
[<ffffffff81468d92>] system_call_fastpath+0x16/0x1b
[<00007f8e4f617fd0>] 0x7f8e4f617fcf
Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0
RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
RSP <ffff8839dc1e7c68>
CR2: 00000000000002a8
Analysis reveals the cause of the crash to be due to STp->device
being NULL. The pointer was NULLed via scsi_tape_put(STp) when it
calls scsi_tape_release(). In st_open() we jump to err_out after
scsi_block_when_processing_errors() completes and returns the
device as offline (sdev_state was SDEV_DEL):
1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host
1181 module count. */
1182 static int st_open(struct inode *inode, struct file *filp)
1183 {
1184 int i, retval = (-EIO);
1185 int resumed = 0;
1186 struct scsi_tape *STp;
1187 struct st_partstat *STps;
1188 int dev = TAPE_NR(inode);
1189 char *name;
...
1217 if (scsi_autopm_get_device(STp->device) < 0) {
1218 retval = -EIO;
1219 goto err_out;
1220 }
1221 resumed = 1;
1222 if (!scsi_block_when_processing_errors(STp->device)) {
1223 retval = (-ENXIO);
1224 goto err_out;
1225 }
...
1264 err_out:
1265 normalize_buffer(STp->buffer);
1266 spin_lock(&st_use_lock);
1267 STp->in_use = 0;
1268 spin_unlock(&st_use_lock);
1269 scsi_tape_put(STp); <-- STp->device = 0 after this
1270 if (resumed)
1271 scsi_autopm_put_device(STp->device);
1272 return retval;
The ref count for the struct scsi_tape had already been reduced
to 1 when the .remove method of the st module had been called.
The kref_put() in scsi_tape_put() caused scsi_tape_release()
to be called:
0266 static void scsi_tape_put(struct scsi_tape *STp)
0267 {
0268 struct scsi_device *sdev = STp->device;
0269
0270 mutex_lock(&st_ref_mutex);
0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this
0272 scsi_device_put(sdev);
0273 mutex_unlock(&st_ref_mutex);
0274 }
In scsi_tape_release() the struct scsi_device in the struct
scsi_tape gets set to NULL:
4273 static void scsi_tape_release(struct kref *kref)
4274 {
4275 struct scsi_tape *tpnt = to_scsi_tape(kref);
4276 struct gendisk *disk = tpnt->disk;
4277
4278 tpnt->device = NULL; <<<---- where the dev is nulled
4279
4280 if (tpnt->buffer) {
4281 normalize_buffer(tpnt->buffer);
4282 kfree(tpnt->buffer->reserved_pages);
4283 kfree(tpnt->buffer);
4284 }
4285
4286 disk->private_data = NULL;
4287 put_disk(disk);
4288 kfree(tpnt);
4289 return;
4290 }
Although the problem was reported on SLES11.3 the problem appears
in linux-next as well.
The crash is fixed by reordering the code so we no longer access
the struct scsi_tape after the kref_put() is done on it in st_open().
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Signed-off-by: Darren Lavender <darren.lavender@hp.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
OMAP GPIO driver allowed to be built as loadable module, but it
doesn't set owner field in GPIO chip structure. As result,
module_get/put() API is not working and it's possible to unload
OMAP driver while in use:
omap_gpio 48051000.gpio: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
Hence, add missing configuration.
Cc: Tony Lindgren <tony@atomide.com>
Fixes: cac089f9026e ('gpio: omap: Allow building as a loadable module')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In case the gpiochip doesn't have the .dev field set, as is the case
in here, it is not possible to reference this device in DT as a GPIO
controller. A good example of this problem is that gpio-leds can not
be used when connected to this chip, the gpio-leds driver bails out
with -EPROBE_DEFER.
Fix this problem by setting the .dev field of the gpio_chip to the
parent i2c device.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
xgpio_save_regs() is used in this driver to setup the initial
values of the registers in the hardware.
The relevant registers at that time are:
0x0 -> channel 0 data (32 bits, one for each GPIO on this channel).
0x4 -> channel 0 tri, controls in/out status for each GPIO of this channel.
0x8 -> channel 1 data
0xC -> channel 1 tri
gpio-xilinx.c defines these:
XGPIO_DATA_OFFSET (0x0)
XGPIO_TRI_OFFSET (0x4)
XGPIO_CHANNEL_OFFSET 0x8
Before this patch, the "data" register value of channel 1 was written
at 0x4 intead of 0x8 (overwriting the channel 0 "tri" register),
and the "tri" register value for channel 1 was written at 0x8 instead of 0xC.
Signed-off-by: Raphaël Teysseyre <rteysseyre@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing pm_runtime_disabled to remove().
Error log:
root@zynqmp:~# modprobe gpio_zynq
root@zynqmp:~# lsmod
Not tainted
gpio_zynq 7086 0 - Live 0xffffffbffc00a000
root@zynqmp:~# rmmod gpio_zynq
root@zynqmp:~# lsmod
Not tainted
root@zynqmp:~# modprobe gpio_zynq
[ 246.924438] zynq-gpio ff0a0000.gpio: Unbalanced pm_runtime_enable!
root@zynqmp:~# rmmod gpio_zynq
root@zynqmp:~# lsmod
Not tainted
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
