| Age | Commit message (Collapse) | Author |
|---|
|
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As we disable the log capture events, flush any residual interrupt
before we flush and disable the worker.
v2: Mika pointed out that it wasn't the worker re-queueing itself, but a
rogue irq.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109716
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221163833.21393-1-chris@chris-wilson.co.uk
|
|
Currently there is a small race window where we could manage to arm the
vblank event from atomic flush, but programming the hardware was too close
to the frame end, so the hardware will only apply the current state on the
next vblank. In this case we will send out the commit done event too early
causing userspace to reuse framebuffes that are still in use.
Instead of using the event arming mechnism, just remember the pending event
and send it from the vblank IRQ handler, once we are sure that all state
has been applied successfully.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending, added back
spinlock in atomic_flush, commit message typo fix]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Allow to compile-test imx-drm on other platforms.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the TVE provides a clock to the DI, the driver can only be
compiled if the common clock framework is enabled. With the COMMON_CLK
dependency in place, it will be possible to allow building the other
parts of imx-drm under COMPILE_TEST on architectures that do not select
the common clock framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a zpos property to planes. Call drm_atomic_helper_check() instead of
calling drm_atomic_helper_check_modeset() and drm_atomic_check_planes()
manually. This effectively adds a call to drm_atomic_normalize_zpos()
before checking planes. Reorder atomic update to allow changing plane
zpos without modeset.
Note that the initial zpos is set in ipu_plane_state_reset(). The
initial value set in ipu_plane_init() is just for show. The zpos
parameter of drm_plane_create_zpos_property() is ignored because
the newly created plane do not have state yet.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Marius Vlad <marius.vlad@collabora.com>
|
|
This function allows upper layer to check if a requested atomic update
to the plane has been applied or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This allows channels using the PRG to check if a requested configuration
update has been applied or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
This allows the upper layers to check if a double buffer update has
been applied by the PRE or is still pending.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: inverted logic: done -> pending]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
* pm-cpufreq-fixes:
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
|
|
into drm-next
Fixes for 5.1:
amdgpu:
- Fix missing fw declaration after dropping old CI DPM code
- Fix debugfs access to registers beyond the MMIO bar size
- Fix context priority handling
- Add missing license on some new files
- Various cleanups and bug fixes
radeon:
- Fix missing break in CS parser for evergreen
- Various cleanups and bug fixes
sched:
- Fix entities with 0 run queues
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221214134.3308-1-alexander.deucher@amd.com
|
|
The SHA512 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SHA256 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 1358c13a48c4 ("crypto: ccree - fix resume race condition on init")
was missing a "inline" qualifier for stub function used when CONFIG_PM
is not set causing a build warning.
Fixes: 1358c13a48c4 ("crypto: ccree - fix resume race condition on init")
Cc: stable@kernel.org # v4.20
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
clang warns about overflowing the data[] member in the struct pnpipehdr:
net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds]
if (hdr->data[4] == PEP_IND_READY)
^ ~
include/net/phonet/pep.h:66:3: note: array 'data' declared here
u8 data[1];
Using a flexible array member at the end of the struct avoids the
warning, but since we cannot have a flexible array member inside
of the union, each index now has to be moved back by one, which
makes it a little uglier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2019-02-21
1) Don't do TX bytes accounting for the esp trailer when sending
from a request socket as this will result in an out of bounds
memory write. From Martin Willi.
2) Destroy xfrm_state synchronously on net exit path to
avoid nested gc flush callbacks that may trigger a
warning in xfrm6_tunnel_net_exit(). From Cong Wang.
3) Do an unconditionally clone in pfkey_broadcast_one()
to avoid a race when freeing the skb.
From Sean Tranchetti.
4) Fix inbound traffic via XFRM interfaces across network
namespaces. We did the lookup for interfaces and policies
in the wrong namespace. From Tobias Brunner.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lorenzo Bianconi says:
====================
report erspan version field just for erspan tunnels
Do not report erspan_version to userpsace for non erspan tunnels.
Report IFLA_GRE_ERSPAN_INDEX only for erspan version 1 in
ip6gre_fill_info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report erspan version field to userspace in ip6gre_fill_info just for
erspan_v6 tunnels. Moreover report IFLA_GRE_ERSPAN_INDEX only for
erspan version 1.
The issue can be triggered with the following reproducer:
$ip link add name gre6 type ip6gre local 2001::1 remote 2002::2
$ip link set gre6 up
$ip -d link sh gre6
14: grep6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1448 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre6 2001::1 peer 2002::2 promiscuity 0 minmtu 0 maxmtu 0
ip6gre remote 2002::2 local 2001::1 hoplimit 64 encaplimit 4 tclass 0x00 flowlabel 0x00000 erspan_index 0 erspan_ver 0 addrgenmode eui64
Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report erspan version field to userspace in ipgre_fill_info just for
erspan tunnels. The issue can be triggered with the following reproducer:
$ip link add name gre1 type gre local 192.168.0.1 remote 192.168.1.1
$ip link set dev gre1 up
$ip -d link sh gre1
13: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre 192.168.0.1 peer 192.168.1.1 promiscuity 0 minmtu 0 maxmtu 0
gre remote 192.168.1.1 local 192.168.0.1 ttl inherit erspan_ver 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1
Fixes: f551c91de262 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
A bit bigger than normal for this week due to fixes for some long
standing display issues that are bound for stable. These changes would
be going to stable anyway, so I figured it was better via 5.0 than 5.1.
- Several display fixes
- Fix PX systems due to core changes in runtime pm
- Disable bulk moves. They are fixed in 5.1, but fix is too invasive for 5.0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220225715.3240-1-alexander.deucher@amd.com
|
|
The first release of core4 (0x54) was dual issue only (HS4x).
Newer releases allow hardware to be configured as single issue (HS3x)
or dual issue.
Prevent accessing a HS4x only aux register in HS3x, which otherwise
leads to illegal instruction exceptions
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.
But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.
Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.
Exclude callers for which network header offset is not known.
Fixes: d5be7f632bad ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tung Nguyen says:
====================
tipc: improvement for wait and wakeup
Some improvements for tipc_wait_for_xzy().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 844cf763fba6 ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6fe4 bonding: pass link-local packets to bonding master also.
... to:
b89f04c61efe bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6fe4 restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6fe4 (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similiar to commit e94cd8113ce63 ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The listed address for the CAIF maintainer bounces with
"553 5.3.0 <dmitry.tarnyagin@lockless.no>... No such user here", and the
only existing email address of the maintainer in git history hasn't
responded in a week.
Therefore, remove the listed maintainer and mark CAIF as orphan.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/BOCO/BACO/g
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use a proper return code rather than -1.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Trivial.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-02-21
This series contains fixes to ixgbe and i40e.
Majority of the fixes are to resolve XDP issues found in both drivers,
there is only one fix which is not XDP related. That one fix resolves
an issue seen on older 10GbE devices, where UDP traffic was either being
dropped or being transmitted out of order when the bit to enable L3/L4
filtering for transmit switched packets is enabled on older devices that
did not support this option.
Magnus fixes an XDP issue for both ixgbe and i40e, where receive rings
are created but no buffers are allocated for AF_XDP in zero-copy mode,
so no packets can be received and no interrupts will be generated so
that NAPI poll function that allocates buffers to the rings will never
get executed.
Björn fixes a race in XDP xmit ring cleanup for i40e, where
ndo_xdp_xmit() must be taken into consideration. Added a
synchronize_rcu() to wait for napi(s) before clearing the queue.
Jan fixes a ixgbe AF_XDP zero-copy transmit issue which can cause a
reset to be triggered, so add a check to ensure that netif carrier is
'ok' before trying to transmit packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Retire the parisc-linux.org email domain and provide alternative email
addresses for the remaining users, as agreed upon with them.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
An issue has been found while testing zero-copy XDP that
causes a reset to be triggered. As it takes some time to
turn the carrier on after setting zc, and we already
start trying to transmit some packets, watchdog considers
this as an erroneous state and triggers a reset.
Don't do any work if netif carrier is not OK.
Fixes: 8221c5eba8c13 (ixgbe: add AF_XDP zero-copy Tx support)
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 910cd32e552e ("parisc: Fix and enable seccomp filter support")
introduced a regression in ptrace-based syscall tampering: when tracer
changes syscall number to -1, the kernel fails to initialize %r28 with
-ENOSYS and subsequently fails to return the error code of the failed
syscall to userspace.
This erroneous behaviour could be observed with a simple strace syscall
fault injection command which is expected to print something like this:
$ strace -a0 -ewrite -einject=write:error=enospc echo hello
write(1, "hello\n", 6) = -1 ENOSPC (No space left on device) (INJECTED)
write(2, "echo: ", 6) = -1 ENOSPC (No space left on device) (INJECTED)
write(2, "write error", 11) = -1 ENOSPC (No space left on device) (INJECTED)
write(2, "\n", 1) = -1 ENOSPC (No space left on device) (INJECTED)
+++ exited with 1 +++
After commit 910cd32e552ea09caa89cdbe328e468979b030dd it loops printing
something like this instead:
write(1, "hello\n", 6../strace: Failed to tamper with process 12345: unexpectedly got no error (return value 0, error 0)
) = 0 (INJECTED)
This bug was found by strace test suite.
Fixes: 910cd32e552e ("parisc: Fix and enable seccomp filter support")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d4f ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427b6 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The default value of ARCH_SLAB_MINALIGN in "include/linux/slab.h" is
"__alignof__(unsigned long long)" which for ARC unexpectedly turns out
to be 4. This is not a compiler bug, but as defined by ARC ABI [1]
Thus slab allocator would allocate a struct which is 32-bit aligned,
which is generally OK even if struct has long long members.
There was however potetial problem when it had any atomic64_t which
use LLOCKD/SCONDD instructions which are required by ISA to take
64-bit addresses. This is the problem we ran into
[ 4.015732] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.167881] Misaligned Access
[ 4.172356] Path: /bin/busybox.nosuid
[ 4.176004] CPU: 2 PID: 171 Comm: rm Not tainted 4.19.14-yocto-standard #1
[ 4.182851]
[ 4.182851] [ECR ]: 0x000d0000 => Check Programmer's Manual
[ 4.190061] [EFA ]: 0xbeaec3fc
[ 4.190061] [BLINK ]: ext4_delete_entry+0x210/0x234
[ 4.190061] [ERET ]: ext4_delete_entry+0x13e/0x234
[ 4.202985] [STAT32]: 0x80080002 : IE K
[ 4.207236] BTA: 0x9009329c SP: 0xbe5b1ec4 FP: 0x00000000
[ 4.212790] LPS: 0x9074b118 LPE: 0x9074b120 LPC: 0x00000000
[ 4.218348] r00: 0x00000040 r01: 0x00000021 r02: 0x00000001
...
...
[ 4.270510] Stack Trace:
[ 4.274510] ext4_delete_entry+0x13e/0x234
[ 4.278695] ext4_rmdir+0xe0/0x238
[ 4.282187] vfs_rmdir+0x50/0xf0
[ 4.285492] do_rmdir+0x9e/0x154
[ 4.288802] EV_Trap+0x110/0x114
The fix is to make sure slab allocations are 64-bit aligned.
Do note that atomic64_t is __attribute__((aligned(8)) which means gcc
does generate 64-bit aligned references, relative to beginning of
container struct. However the issue is if the container itself is not
64-bit aligned, atomic64_t ends up unaligned which is what this patch
ensures.
[1] https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/wiki/files/ARCv2_ABI.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked changelog, added dependency on LL64+LLSC]
|
|
After reworking U-boot args handling code and adding paranoid
arguments check we can eliminate CONFIG_ARC_UBOOT_SUPPORT and
enable uboot support unconditionally.
For JTAG case we can assume that core registers will come up
reset value of 0 or in worst case we rely on user passing
'-on=clear_regs' to Metaware debugger.
Cc: stable@vger.kernel.org
Tested-by: Corentin LABBE <clabbe@baylibre.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Handle U-boot arguments paranoidly:
* don't allow to pass unknown tag.
* try to use external device tree blob only if corresponding tag
(TAG_DTB) is set.
* don't check uboot_tag if kernel build with no ARC_UBOOT_SUPPORT.
NOTE:
If U-boot args are invalid we skip them and try to use embedded device
tree blob. We can't panic on invalid U-boot args as we really pass
invalid args due to bug in U-boot code.
This happens if we don't provide external DTB to U-boot and
don't set 'bootargs' U-boot environment variable (which is default
case at least for HSDK board) In that case we will pass
{r0 = 1 (bootargs in r2); r1 = 0; r2 = 0;} to linux which is invalid.
While I'm at it refactor U-boot arguments handling code.
Cc: stable@vger.kernel.org
Tested-by: Corentin LABBE <clabbe@baylibre.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
There's a hardware bug which affects the HSDK platform, triggered by
micro-ops for auto-saving regfile on taken interrupt. The workaround is
to inhibit autosave.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Newer ARC gcc handles lp_start, lp_end in a different way and doesn't
like them in the clobber list.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Fix reversed logic while actionpoints configuration (full/min)
detection.
Fixies: 7dd380c338f1e ("ARC: boot log: print Action point details")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
ARCv2 optimized memcpy uses PREFETCHW instruction for prefetching the
next cache line but doesn't ensure that the line is not past the end of
the buffer. PRETECHW changes the line ownership and marks it dirty,
which can cause data corruption if this area is used for DMA IO.
Fix the issue by avoiding the PREFETCHW. This leads to performance
degradation but it is OK as we'll introduce new memcpy implementation
optimized for unaligned memory access using.
We also cut off all PREFETCH instructions at they are quite useless
here:
* we call PREFETCH right before LOAD instruction call.
* we copy 16 or 32 bytes of data (depending on CONFIG_ARC_HAS_LL64)
in a main logical loop. so we call PREFETCH 4 times (or 2 times)
for each L1 cache line (in case of 64B L1 cache Line which is
default case). Obviously this is not optimal.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
It is currently done in arc_init_IRQ() which might be too late
considering gcc 7.3.1 onwards (GNU 2018.03) generates unaligned
memory accesses by default
Cc: stable@vger.kernel.org #4.4+
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog]
|
|
When the RX rings are created they are also populated with buffers so
that packets can be received. Usually these are kernel buffers, but
for AF_XDP in zero-copy mode, these are user-space buffers and in this
case the application might not have sent down any buffers to the
driver at this point. And if no buffers are allocated at ring creation
time, no packets can be received and no interrupts will be generated so
the NAPI poll function that allocates buffers to the rings will never
get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once after
an XDP program has loaded and once after the umem is registered. This
take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The enabling L3/L4 filtering for transmit switched packets for all
devices caused unforeseen issue on older devices when trying to send UDP
traffic in an ordered sequence. This bit was originally intended for X550
devices, which supported this feature, so limit the scope of this bit to
only X550 devices.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
smc_poll() returns with mask bit EPOLLPRI if the connection urg_state
is SMC_URG_VALID. Since SMC_URG_VALID is zero, smc_poll signals
EPOLLPRI errorneously if called in state SMC_INIT before the connection
is created, for instance in a non-blocking connect scenario.
This patch switches to non-zero values for the urg states.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Fixes: de8474eb9d50 ("net/smc: urgent data support")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
ipv6: route: enforce RCU protection for fib6_info->from
This series addresses a couple of RCU left-over dating back to rt6_info->from
conversion to RCU
v1 -> v2:
- fix a possible race in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
