| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 changes for 4.4" from Heiko Stuebner:
DTS changes including one new Veyron-board and the Radxa Rock2
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
* tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the support power-domain node on RK3288 SoCs
ARM: dts: rockchip: add rk3288-firefly iodomains
ARM: dts: rockchip: fixup firefly mmc supplies
ARM: dts: rockchip: add rk3288-popmetal iodomains
ARM: dts: rockchip: add rk3288-popmetal mmc supplies
ARM: dts: rockchip: add rk3288-popmetal board to dtb list
ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board
ARM: dts: rockchip: support highspeed sd-cards on rk3066a boards
ARM: dts: rockchip: support highspeed sd-cards for rk3188-radxarock
ARM: dts: rockchip: Add the hdmi-ddc pinctrl settings for rk3288
ARM: dts: rockchip: Remove specific cts pullup from veyron
ARM: dts: rockchip: pull up cts lines on rk3288
ARM: dts: rockchip: add veyron-jaq board
ARM: dts: rockchip: Add support for SD/MMC on MarsBoard-RK3066
dt-bindings: add power-domain header for RK3288 SoCs
|
|
We can add more domains node in the future.
This patch add the needed clocks into power-controller.
As the discuess about all the device clocks being listed in
the power-domains itself.
There are several reasons as follows:
Firstly, the clocks need be turned off to save power when
the system enter the suspend state. So we need to enumerate
the clocks in the dts. In order to power domain can turn on and off.
Secondly, the reset-circuit should reset be synchronous on RK3288,
then sync revoked. So we need to enable clocks of all devices.
In other words, we have to enable the clocks before you operate them
if all the device clocks are included in someone domians.
Thirdly, as the chip designs for PM hardhare. we need turn on the noc
clocks, if we are operating the "pd_vio" domain to enter the idle status.
The device's clock be included in domains that needed turn on if do that.
The clocks in the dts are needed to enable before you want to happy work.
At the moment, This patch is very good work for PM hardware.
Also, we can add these clocks in the future if we have some hidden clocks.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
[add necessary power-domain properties to keep drm subsys working]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
|
|
Add the iodomains node and reference the correct regulator for each
domain. This also includes adding the currently unused dvp regulators.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix some incorrect references to mmc regulators.
vccio_wl for example is the io-voltage supply not the core supply
of the wifi module itself, which is vbat_wl instead.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the iodomains node and reference the correct regulator for each
domain. This also includes adding the currently unused dvp regulators
and fixing up two regulators to follow the naming in the schematics.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add missing regulators and supply properties to emmc and sdmmc nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The popmetal board was not included in the list of Rockchip boards,
so was only built when explicitly called with make rk3288-popmetal.dtb
but not in a generic make dtbs, so add the missing entry.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add cap-sd-highspeed and cap-mmc-highspeed for rk3066a-bqcurie2
and rk3066a-rayeager boards to make sd cards run faster.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add cap-sd-highspeed and cap-mmc-highspeed for rk3188-radxarock
board to make sd cards running faster.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The pins for i2c5 can either be configured as "I2C5" which means that
they're controlled by the normal RK3288 I2C controller or as "EDP / HDMI
I2C". It's unclear why EDP is referenced here since apparently setting
the mux to this position enables I2C communication using the dw_hdmi
block with a patch like <https://patchwork.kernel.org/patch/7098101/>.
There appear to be some reasons why using the builtin I2C controller in
dw_hdmi is better than using the normal RK3288 I2C controller, so boards
based on rk3288 might eventually want to use this pinmux if it's known
to work.
Once driver support in dw_hdmi lands, boards would use this by selecting
this pinctrl for the HDMI block and then _not_ specifying a ddc-i2c-bus
and _not_ setting the status to "okay" for i2c5 (which uses the same
pins).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
With the previous patch ("rk3288: pull up cts lines") this is redundant,
I sent that patch for the same reason this existed here, so the lines don't
wiggle randomly when disconnected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The flow control lines from a user accessible UART are optional,
the user might not have anything connected to those pins.
In order to prevent random interrupts happening and noise affecting
the cts pin should be pulled up.
Note that the default state for that pin on the rk3288 is pulled up,
so this patch merely restores them.
This is similar to what we're already doing with the RX pin,
so it should be safe. At worst it might be a slightly higher power usage
(through ~50 kohms) when the cts is low.
Suggested-by: Neil Hendin <nhendin@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
a.k.a. Haier Chromebook 11, and others
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This enables SDMMC0 on the board and gives a basic support for SD cards.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM Keystone DTS updates" from Santosh Shilimkar:
- Add SOC compatible along with EVMs for future board variations.
- Add SPI nodes
* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Update SoC specific compatible flags
ARM: keystone: Update compatible to have SoC specific matches
Documentation: dt: keystone: provide SoC specific compatible flags
ARM: dts: keystone: Add ti,keystone-spi for SPI
|
|
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tronfy is an emerging brand in China specializing in Home Theater
solutions for the normal consumers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.4" from Simon Horman:
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
* tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (28 commits)
ARM: shmobile: porter: add Ether DT support
ARM: shmobile: fix SILK board name
ARM: shmobile: r8a7794: add HS-USB DT support
ARM: shmobile: dts: Add common file for AA121TD01 panel
ARM: shmobile: r8a7794: link PCI USB devices to USB PHY
ARM: shmobile: silk: enable USB PHY
ARM: shmobile: r8a7794: add USB PHY DT support
ARM: shmobile: porter: initial device tree
ARM: shmobile: add Porter board DT bindings
ARM: shmobile: silk: enable internal PCI
ARM: shmobile: r8a7794: add internal PCI bridge nodes
ARM: shmobile: r8a7790: lager: add pinmux for iic0
ARM: shmobile: r8a7778: tidyup SSI resource region
ARM: shmobile: r8a7791: tidyup SSI resource region
ARM: shmobile: r8a7790: tidyup SSI resource region
ARM: shmobile: lager: use CCF for audio clock
ARM: shmobile: koelsch: use CCF for audio clock
ARM: shmobile: silk: add VIN0/ADV7180 DT support
ARM: shmobile: r8a7794: add VIN DT support
ARM: shmobile: silk: add I2C1 DT support
...
|
|
Dependency for renesas/dt
|
|
Update the compatible flags to allow specific SoC identification.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
With future SoCs of keystone2 family, the generic compatible match
may not be sufficient to handle SoC specific handling. So introduce
matches based on SoC compatiblity.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
Keystone2 devices are used on more platforms than just Texas
Instruments reference evaluation platforms called EVMs. Providing a
generic compatible "ti,keystone" is not sufficient to differentiate
various SoC definitions possible on various platforms for the
following reasons:
a) Userspace applications have no way of knowing which SoC they are
functioning, providing the compatible matches provide a mechanism for
them to enable SoC specific functionality. Such userspace applications
are typically automated test framework or SoC custom hardware
acceleration entitlement from a common file system.
b) Provides an accurate hardware description. This allows
SoC specific logic to be run time handled based on
of_machine_is_compatible("ti,k2hk") or as needed for the dependent
processor instead of needing to use board dependent compatibles that
are needed now.
Hence, provide compatible matches for each SoC in the Keystone family.
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
|
|
This patch adds all UART nodes for the Hi6220 SoC. Recently a board[1] has
been developed to standardize UART access across all the 96boards consumer
edition boards. To use this hardware on HiKey we must configure and enable
UART3. However, to ensure backward compatibility we must keep UART0 enabled
as well.
I have removed the hard coded clock index values in favor of using the ones
already defined in include/dt-bindings/clock/hi6220-clock.h.
Since UART0 needs to be soldered, it has been suggested to use the UART3 as
the default console.
This patch was boot tested on top of next-20150930, with both UART
configurations.
[1] http://www.seeedstudio.com/depot/96Boards-UART-p-2525.html?ref=newInBazaar
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Merge "SoCFPGA DTS updates for v4.4" from Dinh Nguyen:
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
* tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: Add base stratix 10 dtsi
ARM: socfpga: dts: enable USB and I2C on Arria10 SoCDK
ARM: socfpga: dts: add clock fields for I2C, UART and USB on Arria10
|
|
https://github.com/AppliedMicro/xgene-next into next/dt
Merge "X-Gene DTS changes queued for v4.4" from Duc Dang:
* tag 'xgene-dts-for-v4.4-1' of https://github.com/AppliedMicro/xgene-next:
arm64: dts: Add poweroff device nodes for APM X-Gene 2 platform
arm64: dts: Add APM X-Gene 2 standby GPIO controller DTS entries
arm64: dts: Add PMU node for APM X-Gene Storm SOC
Documentation: arm: pmu: Add Potenza PMU binding
arm64: dts: Add X-Gene v2 reboot driver dts node
arm64: dts: add APM Merlin Board device tree
power: reset: Add syscon poweroff device node for APM X-Gene platform
arm64: dts: Add X-Gene reboot driver dts node
Documentation: arm64: add SCU dts binding documentation to linux kernel
MAINTAINERS: Add Applied Micro (APM) X-Gene Device Tree maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "First batch of DT changes for 4.4:" from Nicolas Ferre:
- some DT fixes: dma declaration, led labels
- disable some nodes: PMIC on sama5d3 Xplained, unused i2c1 on at91sam9n12ek
- add some others that were missing: touchscreen, cryto nodes, LCD panels or
image capture properties on various boards
- as the new pinmux for sama5d2 was accepted, we can now add the definitions
and the actual muxing for sama5d2 Xplained board
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: add device pin muxing
ARM: at91/dt: add sama5d2 pinmux
ARM: at91/dt: ov2640: add hsync/vsync-active property
ARM: at91/dt: sama5d4 xplained: enable the led D8
ARM: at91/dt: sama5d4ek: Add support of QT1070 and Maxtouch
ARM: at91/dt: sama5d4: enable crypto nodes
ARM: at91/dt: sama5d4: add pioD pin mux mask and enable pioD
ARM: at91/dt: sama5d3: update iio config for touchscreen
ARM: at91/dt: sama5d3 xplained: disable pmic
ARM: at91/dt: at91sam9x5: enable iio touchscreen for 9x5ek
ARM: at91/dt: at91sam9n12ek: disable i2c1
ARM: at91/dt: at91sam9n12ek: fix the led labels name
ARM: at91/dt: corrections to i2c1 declaration to sama5d4
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt
Merge "STi DT changes for v4.4, round 1" from Maxime Coquelin:
Highlights:
-----------
- Add multiple pinctrl configurations to STiH407
- Enable devices using pins only at board level
- Add HW RNG device nodes to STiH407 family
- Fix MMC0 clock configuration on STiH418
- Fix interrupt related bindings on STiH407
* tag 'sti-dt-for-v4.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: STi: STiH407: Enable the 2 HW Random Number Generators for STiH4{07, 10}
ARM: DT: STi: STiH418: Fix mmc0 clock configuration
ARM: STi: DT: STiH407: Rename incorrect interrupt related binding
ARM: STi: STiH407: Add spi default pinctrl groups.
ARM: DT: STiH407: Add RMII pinctrl support
ARM: DT: STiH407: Add pinconfig for IRB UHF and IRB TX
ARM: DT: STiH407: Add SD pinctrl config for mmc0 controller
ARM: DT: STiH407: Add systrace pin configuration
ARM: DT: STiH407: Add NAND flash controller pin configuration
ARM: DT: STiH407: Add SPI FSM (NOR Flash) Controller pin config
ARM: DT: STiH407: Add serial3 pinctrl configuration
ARM: DT: STiH407: Add SPI 3 wire and 4 wire pinctrl configs
ARM: STi: DT: STiH407: Add i2c3 alternate pin configs
ARM: STi: DT: STiH407: Add a cec0 pin definition
ARM: dts: stih410: Enable USB2.0 and related PHY nodes at board level
ARM: dts: stih407/410: Tidy up display nodes
ARM: dts: stih407: Enable PWM nodes only board level
|
|
next/dt
Merge "ARM64: DT: Hisilicon hip05 soc and D02 board updates for 4.3" from Wei Xu:
- Updated the hisilicon devicetree bindings document to support hip05-D02 board
- Added dts files for hip05 SoC and D02 board
* tag 'hip05-dt-for-4.3' of git://github.com/hisilicon/linux-hisi:
arm64: dts: add dts files for Hisilicon Hip05-D02 Development Board
arm64: hip05-d02: Document devicetree bindings for Hisilicon Hip05-D02 Board
|
|
Add the base DTS for Altera's SoCFPGA Stratix 10 platform.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Add a non-zero ranges property for /soc node
v3: change #address-cells and #size-cells to <2>
change the GIC address to 0xfffc1000
update the GIC virtual CPU reg length to 0x2000
v2: use interrupt-affinity for pmu node
|
|
On the Arria10 Devkit, the I2C bus has a serial EEPROM and an RTC
hanging off it. Also, enable the USB node.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Add the required clock fields for all the I2C nodes. Also add missing clock
fields for UART0 and USB1.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Define the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
This patch is analogous to the commit 26b0d2cf73cb ("ARM: shmobile:
henninger: add Ether DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Unfortunately, the SILK board bindings were not quite correct, as the board
name should be all caps. Fix that, adding the board model # in parens and
removing stray semicolon.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the R8A7794 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
|
|
Pull md fixes from Neil Brown:
"Assorted fixes for md in 4.3-rc.
Two tagged for -stable, and one is really a cleanup to match and
improve kmemcache interface.
* tag 'md/4.3-fixes' of git://neil.brown.name/md:
md/bitmap: don't pass -1 to bitmap_storage_alloc.
md/raid1: Avoid raid1 resync getting stuck
md: drop null test before destroy functions
md: clear CHANGE_PENDING in readonly array
md/raid0: apply base queue limits *before* disk_stack_limits
md/raid5: don't index beyond end of array in need_this_block().
raid5: update analysis state for failed stripe
md: wait for pending superblock updates before switching to read-only
|
|
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This update contains:
- Fix for a long standing race affecting /proc/irq/NNN
- One line fix for ARM GICV3-ITS counting the wrong data
- Warning silencing in ARM GICV3-ITS. Another GCC trying to be
overly clever issue"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Count additional LPIs for the aliased devices
irqchip/gic-v3-its: Silence warning when its_lpi_alloc_chunks gets inlined
genirq: Fix race in register_irq_proc()
|
|
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"An abs64() fix in the watchdog driver, and two clocksource driver
NO_IRQ assumption fixes"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Fix abs() usage w/ 64bit values
clocksource/drivers/keystone: Fix bad NO_IRQ usage
clocksource/drivers/rockchip: Fix bad NO_IRQ usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
can trigger under newer EFI firmware"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down
|
|
Pull drm fixes from Dave Airlie:
"Bunch of fixes all over the place, all pretty small: amdgpu, i915,
exynos, one qxl and one vmwgfx.
There is also a bunch of mst fixes, I left some cleanups in the series
as I didn't think it was worth splitting up the tested series"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
drm/dp/mst: add some defines for logical/physical ports
drm/dp/mst: drop cancel work sync in the mstb destroy path (v2)
drm/dp/mst: split connector registration into two parts (v2)
drm/dp/mst: update the link_address_sent before sending the link address (v3)
drm/dp/mst: fixup handling hotplug on port removal.
drm/dp/mst: don't pass port into the path builder function
drm/radeon: drop radeon_fb_helper_set_par
drm: handle cursor_set2 in restore_fbdev_mode
drm/exynos: Staticize local function in exynos_drm_gem.c
drm/exynos: fimd: actually disable dp clock
drm/exynos: dp: remove suspend/resume functions
drm/qxl: recreate the primary surface when the bo is not primary
drm/amdgpu: only print meaningful VM faults
drm/amdgpu/cgs: remove import_gpu_mem
drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
drm/vmwgfx: Fix a command submission hang regression
drm/exynos: remove unused mode_fixup() code
drm/exynos: remove decon_mode_fixup()
drm/exynos: remove fimd_mode_fixup()
...
|
|
According to a description from TRM, add all the power domains.
At the moment, we can support some domains on RK3288.
We can add more types on RK3288 in the future, that's need to do.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
|
|
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
