| Age | Commit message (Collapse) | Author |
|---|
|
All accesses to id.state must be done under the spinlock.
Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
Link: https://lore.kernel.org/r/20200310092545.251365-10-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ib_crate_cm_id() immediately places the id in the xarray, and publishes it
into the remote_id and remote_qpn rbtrees. This makes it visible to other
threads before it is fully set up.
It appears the thinking here was that the states IB_CM_IDLE and
IB_CM_REQ_RCVD do not allow any MAD handler or lookup in the remote_id and
remote_qpn rbtrees to advance.
However, cm_rej_handler() does take an action on IB_CM_REQ_RCVD, which is
not really expected by the design.
Make the whole thing clearer:
- Keep the new cm_id out of the xarray until it is completely set up.
This directly prevents MAD handlers and all rbtree lookups from seeing
the pointer.
- Move all the trivial setup right to the top so it is obviously done
before any concurrency begins
- Move the mutation of the cm_id_priv out of cm_match_id() and into the
caller so the state transition is obvious
- Place the manipulation of the work_list at the end, under lock, after
the cm_id is placed in the xarray. The work_count cannot change on an
ID outside the xarray.
- Add some comments
Link: https://lore.kernel.org/r/20200310092545.251365-9-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
ib_create_cm_id() immediately places the id in the xarray, so it is visible
to network traffic.
The state is initially set to IB_CM_IDLE and all the MAD handlers will
test this state under lock and refuse to advance from IDLE, so adding to
the xarray is harmless.
Further, the set to IB_CM_SIDR_REQ_RCVD also excludes all MAD handlers.
However, the local_id isn't even used for SIDR mode, and there will be no
input MADs related to the newly created ID.
So, make the whole flow simpler so it can be understood:
- Do not put the SIDR cm_id in the xarray. This directly shows that there
is no concurrency
- Delete the confusing work_count and pending_list manipulations. This
mechanism is only used by MAD handlers and timewait, neither of which
apply to SIDR.
- Add a few comments and rename 'cur_cm_id_priv' to 'listen_cm_id_priv'
- Move other loose sets up to immediately after cm_id creation so that
the cm_id is fully configured right away. This fixes an oversight where
the service_id will not be returned back on a IB_SIDR_UNSUPPORTED
reject.
Link: https://lore.kernel.org/r/20200310092545.251365-8-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The lock should not be dropped before doing the pr_debug() print as it is
accessing data protected by the lock, such as id.state.
Fixes: 119bf81793ea ("IB/cm: Add debug prints to ib_cm")
Link: https://lore.kernel.org/r/20200310092545.251365-7-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Any manipulation of cm_id->state must be done under the cm_id_priv->lock,
the two routines that added listens did not follow this rule, because they
never participate in any concurrent access around the state.
However, since this exception makes the code hard to understand, simplify
the flow so that it can be fully locked:
- Move manipulation of listen_sharecount into cm_insert_listen() so it is
trivially under the cm.lock without having to expose the cm.lock to the
caller.
- Push the cm.lock down into cm_insert_listen() and have the function
increment the reference count before returning an existing pointer.
- Split ib_cm_listen() into an cm_init_listen() and do not call
ib_cm_listen() from ib_cm_insert_listen()
- Make both ib_cm_listen() and ib_cm_insert_listen() directly call
cm_insert_listen() under their cm_id_priv->lock which does both a
collision detect and, if needed, the insert (atomically)
- Enclose all state manipulation within the cm_id_priv->lock, notice this
set can be done safely after cm_insert_listen() as no reader is allowed
to read the state without holding the lock.
- Do not set the listen cm_id in the xarray, as it is never correct to
look it up. This makes the concurrency simpler to understand.
Many needless error unwinds are removed in the process.
Link: https://lore.kernel.org/r/20200310092545.251365-6-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Too much of the destruction is very carefully sensitive to the state
and various other things. Move more code to the unconditional path and
add several WARN_ONs to check consistency.
Link: https://lore.kernel.org/r/20200310092545.251365-5-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
When creating a cm_id during REQ the id immediately becomes visible to the
other MAD handlers, and shortly after the state is moved to IB_CM_REQ_RCVD
This allows cm_rej_handler() to run concurrently and free the work:
CPU 0 CPU1
cm_req_handler()
ib_create_cm_id()
cm_match_req()
id_priv->state = IB_CM_REQ_RCVD
cm_rej_handler()
cm_acquire_id()
spin_lock(&id_priv->lock)
switch (id_priv->state)
case IB_CM_REQ_RCVD:
cm_reset_to_idle()
kfree(id_priv->timewait_info);
goto destroy
destroy:
kfree(id_priv->timewait_info);
id_priv->timewait_info = NULL
Causing a double free or worse.
Do not free the timewait_info without also holding the
id_priv->lock. Simplify this entire flow by making the free unconditional
during cm_destroy_id() and removing the confusing special case error
unwind during creation of the timewait_info.
This also fixes a leak of the timewait if cm_destroy_id() is called in
IB_CM_ESTABLISHED with an XRC TGT QP. The state machine will be left in
ESTABLISHED while it needed to transition through IB_CM_TIMEWAIT to
release the timewait pointer.
Also fix a leak of the timewait_info if the caller mis-uses the API and
does ib_send_cm_reqs().
Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
Link: https://lore.kernel.org/r/20200310092545.251365-4-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The test here typod the cm_id_priv to use, it used the one that was
freshly allocated. By definition the allocated one has the matching
cm_handler and zero context, so the condition was always true.
Instead check that the existing listening ID is compatible with the
proposed handler so that it can be shared, as was originally intended.
Fixes: 067b171b8679 ("IB/cm: Share listening CM IDs")
Link: https://lore.kernel.org/r/20200310092545.251365-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
xa_alloc_cyclic() is a SMP release to be paired with some later acquire
during xa_load() as part of cm_acquire_id().
As such, xa_alloc_cyclic() must be done after the cm_id is fully
initialized, in particular, it absolutely must be after the
refcount_set(), otherwise the refcount_inc() in cm_acquire_id() may not
see the set.
As there are several cases where a reader will be able to use the
id.local_id after cm_acquire_id in the IB_CM_IDLE state there needs to be
an unfortunate split into a NULL allocate and a finalizing xa_store.
Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
Link: https://lore.kernel.org/r/20200310092545.251365-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
These judgments were used to keep the compatibility with older versions of
userspace that don't have the field named "cap_flags" in structure
hns_roce_ib_create_cq_resp. But it will be wrong to compare outlen with
the size of resp if another new field were added in resp. oulen should be
compared with the end offset of cap_flags in resp.
Fixes: 4f8f0d5e33dd ("RDMA/hns: Package the flow of creating cq")
Link: https://lore.kernel.org/r/1583845569-47257-1-git-send-email-liweihang@huawei.com
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Leon Romanovsky says:
====================
This series fixes various corner cases in the mlx5_ib MR cache
implementation, see specific commit messages for more information.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_mr-cache':
RDMA/mlx5: Allow MRs to be created in the cache synchronously
RDMA/mlx5: Revise how the hysteresis scheme works for cache filling
RDMA/mlx5: Fix locking in MR cache work queue
RDMA/mlx5: Lock access to ent->available_mrs/limit when doing queue_work
RDMA/mlx5: Fix MR cache size and limit debugfs
RDMA/mlx5: Always remove MRs from the cache before destroying them
RDMA/mlx5: Simplify how the MR cache bucket is located
RDMA/mlx5: Rename the tracking variables for the MR cache
RDMA/mlx5: Replace spinlock protected write with atomic var
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
|
|
If the cache is completely out of MRs, and we are running in cache mode,
then directly, and synchronously, create an MR that is compatible with the
cache bucket using a sleeping mailbox command. This ensures that the
thread that is waiting for the MR absolutely will get one.
When a MR allocated in this way becomes freed then it is compatible with
the cache bucket and will be recycled back into it.
Deletes the very buggy ent->compl scheme to create a synchronous MR
allocation.
Link: https://lore.kernel.org/r/20200310082238.239865-13-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Currently if the work queue is running then it is in 'hysteresis' mode and
will fill until the cache reaches the high water mark. This implicit state
is very tricky and doesn't interact with pending very well.
Instead of self re-scheduling the work queue after the add_keys() has
started to create the new MR, have the queue scheduled from
reg_mr_callback() only after the requested MR has been added.
This avoids the bad design of an in-rush of queue'd work doing back to
back add_keys() until EAGAIN then sleeping. The add_keys() will be paced
one at a time as they complete, slowly filling up the cache.
Also, fix pending to be only manipulated under lock.
Link: https://lore.kernel.org/r/20200310082238.239865-12-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
All of the members of mlx5_cache_ent must be accessed while holding the
spinlock, add the missing spinlock in the __cache_work_func().
Using cache->stopped and flush_workqueue() is an inherently racy way to
shutdown self-scheduling work on a queue. Replace it with ent->disabled
under lock, and always check disabled before queuing any new work. Use
cancel_work_sync() to shutdown the queue.
Use READ_ONCE/WRITE_ONCE for dev->last_add to manage concurrency as
coherency is less important here.
Split fill_delay from the bitfield. C bitfield updates are not atomic and
this is just a mess. Use READ_ONCE/WRITE_ONCE, but this could also use
test_bit()/set_bit().
Link: https://lore.kernel.org/r/20200310082238.239865-11-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Accesses to these members needs to be locked. There is no reason not to
hold a spinlock while calling queue_work(), so move the tests into a
helper and always call it under lock.
The helper should be called when available_mrs is adjusted.
Link: https://lore.kernel.org/r/20200310082238.239865-10-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The size_write function is supposed to adjust the total_mr's to match the
user's request, but lacks locking and safety checking.
total_mrs can only be adjusted by at most available_mrs. mrs already
assigned to users cannot be revoked. Ensure that the user provides a
target value within the range of available_mrs and within the high/low
water mark.
limit_write has confusing and wrong sanity checking, and doesn't have the
ability to deallocate on limit reduction.
Since both functions use the same algorithm to adjust the available_mrs,
consolidate it into one function and write it correctly. Fix the locking
and by holding the spinlock for all accesses to ent->X.
Always fail if the user provides a malformed string.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Link: https://lore.kernel.org/r/20200310082238.239865-9-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The cache bucket tracks the total number of MRs that exists, both inside
and outside of the cache. Removing a MR from the cache (by setting
cache_ent to NULL) without updating total_mrs will cause the tracking to
leak and be inflated.
Further fix the rereg_mr path to always destroy the MR. reg_create will
always overwrite all the MR data in mlx5_ib_mr, so the MR must be
completely destroyed, in all cases, before this function can be
called. Detach the MR from the cache and unconditionally destroy it to
avoid leaking HW mkeys.
Fixes: afd1417404fb ("IB/mlx5: Use direct mkey destroy command upon UMR unreg failure")
Fixes: 56e11d628c5d ("IB/mlx5: Added support for re-registration of MRs")
Link: https://lore.kernel.org/r/20200310082238.239865-8-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
There are many bad APIs here that are accepting a cache bucket index
instead of a bucket pointer. Many of the callers already have a bucket
pointer, so this results in a lot of confusing uses of order2idx().
Pass the struct mlx5_cache_ent into add_keys(), remove_keys(), and
alloc_cached_mr().
Once the MR is in the cache, store the cache bucket pointer directly in
the MR, replacing the 'bool allocated_from cache'.
In the end there is only one place that needs to form index from order,
alloc_mr_from_cache(). Increase the safety of this function by disallowing
it from accessing cache entries in the ODP special area.
Link: https://lore.kernel.org/r/20200310082238.239865-7-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The old names do not clearly indicate the intent.
Link: https://lore.kernel.org/r/20200310082238.239865-6-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
mkey variant calculation was spinlock protected to make it atomic, replace
that with one atomic variable.
Link: https://lore.kernel.org/r/20200310082238.239865-4-leon@kernel.org
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
As mlx5_ib is the only user of the mlx5_core_create_mkey_cb, move the
logic inside mlx5_ib and cleanup the code in mlx5_core.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
mkey variant is not required for mlx5_core use, move the mkey variant
counter to mlx5_ib.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
On reg_mr_callback() mlx5_ib is recalculating the mkey variant which is
wrong and will lead to using a different key variant than the one
submitted to firmware on create mkey command invocation.
To fix this, we store the mkey variant before invoking the firmware
command and use it later on completion (reg_mr_callback).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Peer to peer support was never implemented, so delete it to make code less
clutter.
Link: https://lore.kernel.org/r/20200310091438.248429-6-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Convert mlx5 driver to use offsetofend() instead of its duplicated
variant.
Link: https://lore.kernel.org/r/20200310091438.248429-5-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Convert mlx4 to use in-kernel offsetofend() instead
of its duplicated implementation.
Link: https://lore.kernel.org/r/20200310091438.248429-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Until now the flex parser capability was used in ib_query_device() to
indicate tunnel_offloads_caps support for mpls_over_gre/mpls_over_udp.
Newer devices and firmware will have configurations with the flexparser
but without mpls support.
Testing for the flex parser capability was a mistake, the tunnel_stateless
capability was intended for detecting mpls and was introduced at the same
time as the flex parser capability.
Otherwise userspace will be incorrectly informed that a future device
supports MPLS when it does not.
Link: https://lore.kernel.org/r/20200305123841.196086-1-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.17
Fixes: e818e255a58d ("IB/mlx5: Expose MPLS related tunneling offloads")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Those macros are already defined in include/linux/mlx5/driver.h, so delete
their duplicate variants.
Link: https://lore.kernel.org/r/20200310075706.238592-1-leon@kernel.org
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The header file rdma_core.h is duplicate, so let's remove it.
Fixes: 622db5b6439a ("RDMA/core: Add trace points to follow MR allocation")
Link: https://lore.kernel.org/r/20200310091656.249696-1-leon@kernel.org
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
'wqe' is already zeroed at the top of the 'while' loop, just a few lines
below, and is not used outside of the loop.
So there is no need to zero it again, or for the variable to be declared
outside the loop.
Link: https://lore.kernel.org/r/20200308065442.5415-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This lock ordering only happens when bonding is enabled and a certain
bonding related event fires. However, since it can happen this is a global
restriction on lock ordering.
Teach lockdep about the order directly and unconditionally so bugs here
are found quickly.
See https://syzkaller.appspot.com/bug?extid=55de90ab5f44172b0c90
Link: https://lore.kernel.org/r/20200227203651.GA27185@ziepe.ca
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Since RDMA rw API support operations with P2P memory sg list, make sure to
map/unmap the scatter list for signature operation correctly.
Link: https://lore.kernel.org/r/20200220100819.41860-2-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Required due to dependencies in following patches.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Yishai Hadas Says:
====================
Expose raw packet pacing APIs to be used by DEVX based applications. The
existing code was refactored to have a single flow with the new raw APIs.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_packet_pacing':
IB/mlx5: Introduce UAPIs to manage packet pacing
net/mlx5: Expose raw packet pacing APIs
|
|
Introduce packet pacing uobject and its alloc and destroy
methods.
This uobject holds mlx5 packet pacing context according to the device
specification and enables managing packet pacing device entries that are
needed by DEVX applications.
Link: https://lore.kernel.org/r/20200219190518.200912-3-leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was a
miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing
for a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (37 commits)
ARM: socfpga_defconfig: Add back DEBUG_FS
arm64: dts: socfpga: agilex: Fix gmac compatible
ARM: bcm2835_defconfig: Explicitly restore CONFIG_DEBUG_FS
arm64: dts: meson: fix gxm-khadas-vim2 wifi
arm64: dts: meson-sm1-sei610: add missing interrupt-names
ARM: meson: Drop unneeded select of COMMON_CLK
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
tee: amdtee: fix memory leak in amdtee_open_session()
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
"Error reporting fix for synopsys_edac: do not overwrite partial
decoded error message (Sherry Sun)"
* tag 'edac_urgent-2020-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/synopsys: Do not print an error with back-to-back snprintf() calls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are four small char/misc driver fixes for reported issues for
5.6-rc5.
These fixes are:
- binder fix for a potential use-after-free problem found (took two
tries to get it right)
- interconnect core fix
- altera-stapl driver fix
All four of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: prevent UAF for binderfs devices II
interconnect: Handle memory allocation errors
altera-stapl: altera_get_note: prevent write beyond end of 'key'
binder: prevent UAF for binderfs devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs fixes from Greg KH:
"Here are four small driver core / debugfs patches for 5.6-rc3:
- debugfs api cleanup now that all debugfs_create_regset32() callers
have been fixed up. This was waiting until after the -rc1 merge as
these fixes came in through different trees
- driver core sync state fixes based on reports of minor issues found
in the feature
All of these have been in linux-next with no reported issues"
* tag 'driver-core-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Skip unnecessary work when device doesn't have sync_state()
driver core: Add dev_has_sync_state()
driver core: Call sync_state() even if supplier has no consumers
debugfs: remove return value of debugfs_create_regset32()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial fixes for 5.6-rc5
Just some small serial driver fixes, and a vt core fixup, full details
are:
- vt fixes for issues found by syzbot
- serdev fix for Apple boxes
- fsl_lpuart serial driver fixes
- MAINTAINER update for incorrect serial files
- new device ids for 8250_exar driver
- mvebu-uart fix
All of these have been in linux-next with no reported issues"
* tag 'tty-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: fsl_lpuart: free IDs allocated by IDA
Revert "tty: serial: fsl_lpuart: drop EARLYCON_DECLARE"
serdev: Fix detection of UART devices on Apple machines.
MAINTAINERS: Add missed files related to Synopsys DesignWare UART
serial: 8250_exar: add support for ACCES cards
tty:serial:mvebu-uart:fix a wrong return
vt: selection, push sel_lock up
vt: selection, push console lock down
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are some small USB and PHY driver fixes for reported issues for
5.6-rc5.
Included in here are:
- phy driver fixes
- new USB quirks
- USB cdns3 gadget driver fixes
- USB hub core fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: gadget: Update chain bit correctly when using sg list
usb: core: port: do error out if usb_autopm_get_interface() fails
usb: core: hub: do error out if usb_autopm_get_interface() fails
usb: core: hub: fix unhandled return by employing a void function
usb: storage: Add quirk for Samsung Fit flash
usb: quirks: add NO_LPM quirk for Logitech Screen Share
usb: usb251xb: fix regulator probe and error handling
phy: allwinner: Fix GENMASK misuse
usb: cdns3: gadget: toggle cycle bit before reset endpoint
usb: cdns3: gadget: link trb should point to next request
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
|
|
Pull rdma fixes from Jason Gunthorpe:
"Nothing particularly exciting, some small ODP regressions from the mmu
notifier rework, another bunch of syzkaller fixes, and a bug fix for a
botched syzkaller fix in the first rc pull request.
- Fix busted syzkaller fix in 'get_new_pps' - this turned out to
crash on certain HW configurations
- Bug fixes for various missed things in error unwinds
- Add a missing rcu_read_lock annotation in hfi/qib
- Fix two ODP related regressions from the recent mmu notifier
changes
- Several more syzkaller bugs in siw, RDMA netlink, verbs and iwcm
- Revert an old patch in CMA as it is now shown to not be allocating
port numbers properly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/iwcm: Fix iwcm work deallocation
RDMA/siw: Fix failure handling during device creation
RDMA/nldev: Fix crash when set a QP to a new counter but QPN is missing
RDMA/odp: Ensure the mm is still alive before creating an implicit child
RDMA/core: Fix protection fault in ib_mr_pool_destroy
IB/mlx5: Fix implicit ODP race
IB/hfi1, qib: Ensure RCU is locked when accessing list
RDMA/core: Fix pkey and port assignment in get_new_pps
RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()
RDMA/rw: Fix error flow during RDMA context initialization
RDMA/core: Fix use of logical OR in get_new_pps
Revert "RDMA/cma: Simplify rdma_resolve_addr() error flow"
|
|
Add the HW bit definition indecating goto chain offload support.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose port rate as part of the port speed register fields.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose the TLS encryption key general object type enum correctly,
and add the IPSec encryption key general object type enum.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add HCA_CAP.egress_acl_forward_to_vport field to check whether HW
supports e-switch vport's egress acl to forward packets to other
e-switch vport or not.
By default E-Switch egress ACL forwards eswitch vports egress packets
to their corresponding NIC/VF vports.
With this cap enabled, the driver is allowed to alter this behavior
and forward packets to arbitrary NIC/VF vports with the following
limitations:
a. Multiple processing paths are supported if all of the following
conditions are met:
- HCA_CAP.egress_acl_forward_to_vport is set ==1.
- A destination of type Flow Table only appears once, as the
last destination in the list.
- Vport destination is supported if
HCA_CAP.egress_acl_forward_to_vport==1. Vport must not be
the Uplink.
b. Flow_tag not supported.
c. This table is only applicable after an FDB table is created.
d. Push VLAN action is not supported.
e. Pop VLAN action cannot be added concurrently to this table and
FDB table.
This feature will be used during port failover in bonding scenario
where two VFs representors are bonded to handle failover egress traffic
(VM's ingress/receive traffic).
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull io_uring fixes from Jens Axboe:
"Here are a few io_uring fixes that should go into this release. This
contains:
- Removal of (now) unused io_wq_flush() and associated flag (Pavel)
- Fix cancelation lockup with linked timeouts (Pavel)
- Fix for potential use-after-free when freeing percpu ref for fixed
file sets
- io-wq cancelation fixups (Pavel)"
* tag 'io_uring-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
io_uring: fix lockup with timeouts
io_uring: free fixed_file_data after RCU grace period
io-wq: remove io_wq_flush and IO_WQ_WORK_INTERNAL
io-wq: fix IO_WQ_WORK_NO_CANCEL cancellation
|
|
Pull block fixes from Jens Axboe:
"Here are a few fixes that should go into this release. This contains:
- Revert of a bad bcache patch from this merge window
- Removed unused function (Daniel)
- Fixup for the blktrace fix from Jan from this release (Cengiz)
- Fix of deeper level bfqq overwrite in BFQ (Carlo)"
* tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
blktrace: fix dereference after null check
Revert "bcache: ignore pending signals when creating gc and allocator thread"
block: Remove used kblockd_schedule_work_on()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a fix for the media controller links in both hantro driver and in
v4l2-mem2mem core
- some fixes for the pulse8-cec driver
- vicodec: handle alpha channel for RGB32 formats, as it may be used
- mc-entity.c: fix handling of pad flags
* tag 'media/v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hantro: Fix broken media controller links
media: mc-entity.c: use & to check pad flags, not ==
media: v4l2-mem2mem.c: fix broken links
media: vicodec: process all 4 components for RGB32 formats
media: pulse8-cec: close serio in disconnect, not adap_free
media: pulse8-cec: INIT_DELAYED_WORK was called too late
|
