| Age | Commit message (Collapse) | Author |
|---|
|
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the nft_offload there is the mate flow_dissector with no
ingress_ifindex but with ingress_iftype that only be used
in the software. So if the mask of ingress_ifindex in meta is
0, this meta check should be bypass.
Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Change register setting from bit number to bit mask.
Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prevent setting of devlink traps on the uplink while in switchdev mode.
In this mode, it is the SW switch responsibility to handle both packets
with a mismatch in destination MAC or VLAN ID. Therefore, there are no
flow steering tables to trap undesirable packets and driver crashes upon
setting a trap.
Fixes: 241dc159391f ("net/mlx5: Notify on trap action by blocking event")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-04-14
this is a pull request of a single patch for net-next/master.
Vincent Mailhol's patch fixes a NULL pointer dereference when handling
error frames in the etas_es58x driver, which has been added in the
previous PR.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
af_packet fanout uses RCU rules to ensure f->arr elements
are not dismantled before RCU grace period.
However, it lacks rcu accessors to make sure KCSAN and other tools
wont detect data races. Stupid compilers could also play games.
Fixes: dc99f600698d ("packet: Add fanout support.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.
Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-13
mlx5 core and netdev driver updates
1) E-Switch updates from Parav,
1.1) Devlink parameter to control mlx5 metadata enablement for E-Switch
1.2) Trivial cleanups for E-Switch code
1.3) Dynamically allocate vport steering namespaces only when required
2) From Jianbo, Use variably sized data structures for Software steering
3) Several minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-04-14
This series contains updates to ixgbe and ice drivers.
Alex Duyck fixes a NULL pointer dereference for ixgbe.
Yongxin Liu fixes an unbalanced enable/disable which was causing a call
trace with suspend for ixgbe.
Colin King fixes a potential infinite loop for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, the bootloader will already initialize the MAC address
registers of the ENETC and the driver will just use them or generate a
random one, if it is not initialized.
Add a new way to provide the MAC address: via device tree. Besides the
usual 'mac-address' property, there is also the possibility to fetch it
via a NVMEM provider. The sl28 board stores the MAC address in the SPI
NOR flash OTP region. Having this will allow linux to fetch the MAC
address from there without being dependent on the bootloader.
No in-tree boards have the device tree properties set, thus for these,
this is a no-op.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following coccicheck warning:
./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the commit 1ddc3229ad3c ("skbuff: remove some unnecessary operation
in skb_segment_list()") introduces an issue very similar to the
one already fixed by commit 53475c5dd856 ("net: fix use-after-free when
UDP GRO with shared fraglist").
If the GSO skb goes though skb_clone() and pskb_expand_head() before
entering skb_segment_list(), the latter will unshare the frag_list
skbs and will release the old list. With the reverted commit in place,
when skb_segment_list() completes, skb->next points to the just
released list, and later on the kernel will hit UaF.
Note that since commit e0e3070a9bc9 ("udp: properly complete L4 GRO
over UDP tunnel packet") the critical scenario can be reproduced also
receiving UDP over vxlan traffic with:
NIC (NETIF_F_GRO_FRAGLIST enabled) -> vxlan -> UDP sink
Attaching a packet socket to the NIC will cause skb_clone() and the
tunnel decapsulation will call pskb_expand_head().
Fixes: 1ddc3229ad3c ("skbuff: remove some unnecessary operation in skb_segment_list()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following clang warning:
drivers/atm/idt77252.c:1787:1: warning: unused function
'idt77252_fbq_level' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM verity target FEC support's RS roots IO to always be aligned.
This fixes a previous stable@ fix that overcorrected for a different
configuration that also resulted in misaligned roots IO"
* tag 'for-5.12/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix misaligned RS roots IO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2021-04-14
Not much this time:
1) Simplification of some variable calculations in esp4 and esp6.
From Jiapeng Chong and Junlin Yang.
2) Fix a clang Wformat warning in esp6 and ah6.
From Arnd Bergmann.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a leftover of the below commit.
Fixes: 4f04256c983a ("net: vrf: Drop local rtable and rt6_info")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's have all seg6 sysctl at the same place.
Fixes: a6dc6670cd7e ("ipv6: sr: Add documentation for seg_flowlabel sysctl")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lijun Pan says:
====================
ibmvnic: correctly call NAPI APIs
This series correct some misuse of NAPI APIs in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The intention was for pause statistics to not be reported
when driver does not have the relevant callback (only
report an empty netlink nest). What happens currently
we report all 0s instead. Make sure statistics are
initialized to "not set" (which is -1) so the dumping
code skips them.
Fixes: 9a27a33027f2 ("ethtool: add standard pause stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
10GbE Intel Wired LAN Driver Updates 2021-04-13
This series contains updates to ixgbe and ixgbevf driver.
Jostar Yang adds support for BCM54616s PHY for ixgbe.
Chen Lin removes an unused function pointer for ixgbe and ixgbevf.
Bhaskar Chowdhury fixes a typo in ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ivan Bornyakov says:
====================
net: phy: marvell-88x2222: a couple of improvements
First, there are some SFP modules that only uses RX_LOS for link
indication. Add check that link is operational before actual read of
line-side status.
Second, it is invalid to set 10G speed without autonegotiation,
according to phy_ethtool_ksettings_set(). Implement switching between
10GBase-R and 1000Base-X/SGMII if autonegotiation can't complete but
there is signal in line.
Changelog:
v1 -> v2:
* make checking that link is operational more friendly for
trancievers without SFP cages.
* split swapping 1G/10G modes into non-functional and functional
commits for the sake of easier review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting 10G without autonegotiation is invalid according to
phy_ethtool_ksettings_set(). Thus, we need to set it during
autonegotiation.
If 1G autonegotiation can't complete for quite a time, but there is
signal in line, switch line interface type to 10GBase-R, if supported,
in hope for link to be established.
And vice versa. If 10GBase-R link can't be established for quite a time,
and autonegotiation is enabled, and there is signal in line, switch line
interface type to appropriate 1G mode, i.e. 1000Base-X or SGMII, if
supported.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No functional changes, just move read link status routines below
autonegotiation configuration to make future functional changes more
distinct.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some SFP modules uses RX_LOS for link indication. In such cases link
will be always up, even without cable connected. RX_LOS changes will
trigger link_up()/link_down() upstream operations. Thus, check that SFP
link is operational before actual read link status.
If there is no SFP cage connected to the tranciever, check only PMD
Recieve Signal Detect register.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ 245.463317] INFO: task iou-sqp-1374:1377 blocked for more than 122 seconds.
[ 245.463334] task:iou-sqp-1374 state:D flags:0x00004000
[ 245.463345] Call Trace:
[ 245.463352] __schedule+0x36b/0x950
[ 245.463376] schedule+0x68/0xe0
[ 245.463385] __io_uring_cancel+0xfb/0x1a0
[ 245.463407] do_exit+0xc0/0xb40
[ 245.463423] io_sq_thread+0x49b/0x710
[ 245.463445] ret_from_fork+0x22/0x30
It happens when sqpoll forgot to run park_task_work and goes to exit,
then exiting user may remove ctx from sqd_list, and so corresponding
io_sq_thread() -> io_uring_cancel_sqpoll() won't be executed. Hopefully
it just stucks in do_exit() in this case.
Fixes: dbe1bdbb39db ("io_uring: handle signals for IO threads like a normal thread")
Reported-by: Joakim Hassila <joj@mac.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to
block size") introduced the possibility for misaligned roots IO
relative to the underlying device's logical block size. E.g. Android's
default RS roots=2 results in dm_bufio->block_size=1024, which causes
the following EIO if the logical block size of the device is 4096,
given v->data_dev_block_bits=12:
E sd 0 : 0:0:0: [sda] tag#30 request not aligned to the logical block size
E blk_update_request: I/O error, dev sda, sector 10368424 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
E device-mapper: verity-fec: 254:8: FEC 9244672: parity read failed (block 18056): -5
Fix this by onlu using f->roots for dm_bufio blocksize IFF it is
aligned to v->data_dev_block_bits.
Fixes: df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size")
Cc: stable@vger.kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Allow to create an RQ which is not registered as an XDP RQ. For example:
the trap-RQ doesn't register as an XDP RQ.
Fixes: 869c5f926247 ("net/mlx5e: Generalize open RQ")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There should be no spaces at the start of the line.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
void function return statements are not generally useful.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There should be a blank lines after declarations.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The bit-wise and of the action field with MLX5_ACCEL_ESP_ACTION_DECRYPT
is incorrect as MLX5_ACCEL_ESP_ACTION_DECRYPT is zero and not intended
to be a bit-flag. Fix this by using the == operator as was originally
intended.
Addresses-Coverity: ("Logically dead code")
Fixes: 7dfee4b1d79e ("net/mlx5: IPsec, Refactor SA handle creation and destruction")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cmd size is 8K so use kvzalloc().
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
