| Age | Commit message (Collapse) | Author |
|---|
|
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88f5 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390bb ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Zhengchao Shao says:
====================
fix some issues in netdevsim driver
When strace tool is used to perform memory injection, memory leaks and
files not removed issues are found. Fix them.
====================
Link: https://lore.kernel.org/r/20221026014642.116261-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes: ab1d0cc004d7 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nsim_dev_resources_register() failed
If some items in nsim_dev_resources_register() fail, memory leak will
occur. The following is the memory leak information.
unreferenced object 0xffff888074c02600 (size 128):
comm "echo", pid 8159, jiffies 4294945184 (age 493.530s)
hex dump (first 32 bytes):
40 47 ea 89 ff ff ff ff 01 00 00 00 00 00 00 00 @G..............
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
backtrace:
[<0000000011a31c98>] kmalloc_trace+0x22/0x60
[<0000000027384c69>] devl_resource_register+0x144/0x4e0
[<00000000a16db248>] nsim_drv_probe+0x37a/0x1260
[<000000007d1f448c>] really_probe+0x20b/0xb10
[<00000000c416848a>] __driver_probe_device+0x1b3/0x4a0
[<00000000077e0351>] driver_probe_device+0x49/0x140
[<0000000054f2465a>] __device_attach_driver+0x18c/0x2a0
[<000000008538f359>] bus_for_each_drv+0x151/0x1d0
[<0000000038e09747>] __device_attach+0x1c9/0x4e0
[<00000000dd86e533>] bus_probe_device+0x1d5/0x280
[<00000000839bea35>] device_add+0xae0/0x1cb0
[<000000009c2abf46>] new_device_store+0x3b6/0x5f0
[<00000000fb823d7f>] bus_attr_store+0x72/0xa0
[<000000007acc4295>] sysfs_kf_write+0x106/0x160
[<000000005f50cb4d>] kernfs_fop_write_iter+0x3a8/0x5a0
[<0000000075eb41bf>] vfs_write+0x8f0/0xc80
Fixes: 37923ed6b8ce ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If device_register() failed in nsim_bus_dev_new(), the value of reference
in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be
released.
unreferenced object 0xffff88810352c480 (size 16):
comm "echo", pid 5691, jiffies 4294945921 (age 133.270s)
hex dump (first 16 bytes):
6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1......
backtrace:
[<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0
[<0000000094ca4fc8>] kvasprintf+0xc3/0x160
[<00000000aad09bcc>] kvasprintf_const+0x55/0x180
[<000000009bac868d>] kobject_set_name_vargs+0x56/0x150
[<000000007c1a5d70>] dev_set_name+0xbb/0xf0
[<00000000ad0d126b>] device_add+0x1f8/0x1cb0
[<00000000c222ae24>] new_device_store+0x3b6/0x5e0
[<0000000043593421>] bus_attr_store+0x72/0xa0
[<00000000cbb1833a>] sysfs_kf_write+0x106/0x160
[<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0
[<00000000770b66e2>] vfs_write+0x8f0/0xc80
[<0000000078bb39be>] ksys_write+0x106/0x210
[<00000000005e55a4>] do_syscall_64+0x35/0x80
[<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 40e4fe4ce115 ("netdevsim: move device registration and related code to bus.c")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221026015405.128795-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-27
Anssi Hannula fixes the use of the completions in the kvaser_usb
driver.
Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm
that can be triggered by high CAN bus load and channel specific IRQ
handlers are fixed.
Yang Yingliang fixes the j1939 transport protocol by moving a
kfree_skb() out of a spin_lock_irqsave protected section.
* tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
can: kvaser_usb: Fix possible completions during init_completion
====================
Link: https://lore.kernel.org/r/20221027114356.1939821-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nicolas Dichtel says:
====================
ip: rework the fix for dflt addr selection for connected nexthop"
This series reworks the fix that is reverted in the second commit.
As Julian explained, nhc_scope is related to nhc_gw, it's not the scope of
the route.
====================
Link: https://lore.kernel.org/r/20221020100952.8748-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit 747c14307214 ("ip: fix
dflt addr selection for connected nexthop").
Fixes: 597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 747c14307214b55dbd8250e1ab44cad8305756f1.
As explained by Julian, nhc_scope is related to nhc_gw, not to the route.
Revert the original patch. The initial problem is fixed differently in the
next commit.
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit eb55dc09b5dd040232d5de32812cc83001a23da6.
The patch that introduces this bug is reverted right after this one.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is possible for tw to lock the ring, and this was not propogated out to
io_run_local_work. This can cause an unlock to be missed.
Instead pass a pointer to locked into __io_run_local_work.
Fixes: 8ac5d85a89b4 ("io_uring: add local task_work run helper that is entered locked")
Signed-off-by: Dylan Yudaken <dylany@meta.com>
Link: https://lore.kernel.org/r/20221027144429.3971400-3-dylany@meta.com
[axboe: WARN_ON() -> WARN_ON_ONCE() and add a minor comment]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
prefer to use io_run_local_work_locked helper for consistency
Signed-off-by: Dylan Yudaken <dylany@meta.com>
Link: https://lore.kernel.org/r/20221027144429.3971400-2-dylany@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During review of previous change another thing came up - we should
limit the use of validation workarounds to old commands.
Don't list the workarounds one by one, as we're rejecting all existing
ones. We can deal with the masking in the unlikely event that new flag
is added.
Link: https://lore.kernel.org/all/6ba9f727e555fd376623a298d5d305ad408c3d47.camel@sipsolutions.net/
Link: https://lore.kernel.org/r/20221026001524.1892202-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.1
- make the multipath dma alignment to match the non-multipath one
(Keith Busch)
- fix a bogus use of sg_init_marker() (Nam Cao)
- fix circulr locking in nvme-tcp (Sagi Grimberg)"
* tag 'nvme-6.1-2022-10-27' of git://git.infradead.org/nvme:
nvme-multipath: set queue dma alignment to 3
nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
nvme-tcp: replace sg_init_marker() with sg_init_table()
|
|
dm-rq implements ->end_io callback for request issued to underlying queue,
and it isn't passthrough request.
Commit ab3e1d3bbab9 ("block: allow end_io based requests in the completion
batch handling") doesn't clear rq->bio and rq->__data_len for request
with ->end_io in blk_mq_end_request_batch(), and this way is actually
dangerous, but so far it is only for nvme passthrough request.
dm-rq needs to clean up remained bios in case of partial completion,
and req->bio is required, then use-after-free is triggered, so the
underlying clone request can't be completed in blk_mq_end_request_batch.
Fix panic by not adding such request into batch list, and the issue
can be triggered simply by exposing nvme pci to dm-mpath simply.
Fixes: ab3e1d3bbab9 ("block: allow end_io based requests in the completion batch handling")
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@kernel.org>
Reported-by: Changhui Zhong <czhong@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20221027085709.513175-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If device_register() returns error in rbd_sysfs_init(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop
the reference count that was set in device_initialize() when it fails,
so the name can be freed in kobject_cleanup().
Fault injection test can trigger this problem:
unreferenced object 0xffff88810173aa78 (size 8):
comm "modprobe", pid 247, jiffies 4294714278 (age 31.789s)
hex dump (first 8 bytes):
72 62 64 00 81 88 ff ff rbd.....
backtrace:
[<00000000f58fae56>] __kmalloc_node_track_caller+0x44/0x1b0
[<00000000bdd44fe7>] kstrdup+0x3a/0x70
[<00000000f7844d0b>] kstrdup_const+0x63/0x80
[<000000001b0a0eeb>] kvasprintf_const+0x10b/0x190
[<00000000a47bd894>] kobject_set_name_vargs+0x56/0x150
[<00000000d5edbf18>] dev_set_name+0xab/0xe0
[<00000000f5153e80>] device_add+0x106/0x1f20
Fixes: dfc5606dc513 ("rbd: replace the rbd sysfs interface")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221027091918.2294132-1-yangyingliang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
spin_unlock_irqrestore() before kfree_skb()
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com
Cc: stable@vger.kernel.org
[mkl: adjust subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes: 1acf2318dd13 ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Aaron Conole says:
====================
openvswitch: syzbot splat fix and introduce selftest
Syzbot recently caught a splat when dropping features from
openvswitch datapaths that are in-use. The WARN() call is
definitely too large a hammer for the situation, so change
to pr_warn.
Second patch in the series introduces a new selftest suite which
can help show that an issue is fixed. This change might be
more suited to net-next tree, so it has been separated out
as an additional patch and can be either applied to either tree
based on preference.
====================
Link: https://lore.kernel.org/r/20221025105018.466157-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previous commit resolves a WARN splat that can be difficult to reproduce,
but with the ovs-dpctl.py utility, it can be trivial. Introduce a test
case which creates a DP, and then downgrades the feature set. This will
include a utility 'ovs-dpctl.py' that can be extended to do additional
tests and diagnostics.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes: 44da5ae5fbea ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PERF_MEM_LVLNUM_EXTN_MEM was introduced to cover CXL devices but it's
bit ambiguous name and also not generic enough to cover cxl.cache and
cxl.io devices. Rename it to PERF_MEM_LVLNUM_CXL to be more specific.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/f6268268-b4e9-9ed6-0453-65792644d953@amd.com
|
|
Raptor Lake RAPL support is the same as previous Sky Lake.
Add Raptor Lake model for RAPL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Link: https://lkml.kernel.org/r/20221023125120.2727-2-rui.zhang@intel.com
|
|
AlderLake-N RAPL support is the same as previous Sky Lake.
Add AlderLake-N model for RAPL.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Link: https://lkml.kernel.org/r/20221023125120.2727-1-rui.zhang@intel.com
|
|
Since commit 838d9bb62d13 ("perf: Use sample_flags for raw_data")
raw data is not being output on tracepoints due to the PERF_SAMPLE_RAW
field not being set. Fix this by setting it for tracepoint events.
This fixes the following test failure:
perf test "sched_switch" -vvv
35: Track with sched_switch
--- start ---
test child forked, pid 1828
...
Using CPUID 0x00000000410fd400
sched_switch: cpu: 2 prev_tid -14687 next_tid 0
sched_switch: cpu: 2 prev_tid -14687 next_tid 0
Missing sched_switch events
4613 events recorded
test child finished with -1
---- end ----
Track with sched_switch: FAILED!
Fixes: 838d9bb62d13 ("perf: Use sample_flags for raw_data")
Signed-off-by: James Clark <james.clark@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20221012143857.48198-1-james.clark@arm.com
|
|
Biju Das <biju.das.jz@bp.renesas.com> says:
This patch series fixes the below issues in R-Car CAN-FD driver.
1) Race condition in CAN driver under heavy CAN load condition
with both channels enabled results in IRQ storm on global FIFO
receive IRQ line.
2) Add channel specific TX interrupts handling for RZ/G2L SoC as it has
separate IRQ lines for each TX.
changes since v1: https://lore.kernel.org/all/20221022081503.1051257-1-biju.das.jz@bp.renesas.com
* Added check for IRQ active and enabled before handling the IRQ on a
particular channel.
Link: https://lore.kernel.org/all/20221025155657.1426948-1-biju.das.jz@bp.renesas.com
[mkl: adjust message, add link, take only patches 1 + 2, upstream 3 via can-next]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
FIFO receive
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Return on error directly from the BAR-iterating loop instead of
break+return.
This is actually a cosmetic fix, since it would be highly unusual to
have this called for a PCI device without any memory BARs.
Fixes: 9d69ef183815 ("fbdev/core: Remove remove_conflicting_pci_framebuffers()")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/e75323732bedc46d613d72ecb40f97e3bc75eea8.1666829073.git.mirq-linux@rere.qmqm.pl
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.1-2022-10-26-1:
amdgpu:
- Stable pstate fix
- SMU 13.x updates
- SR-IOV fixes
- PCI AER fix
- GC 11.x fixes
- Display fixes
- Expose IMU firmware version for debugging
- Plane modifier fix
- S0i3 fix
amdkfd:
- Fix possible memory leak
- Fix GC 10.x cache info reporting
UAPI:
- Expose IMU firmware version via existing INFO firmware query
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221027024101.6881-1-alexander.deucher@amd.com
|
|
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
i2sbus_add_dev() is supposed to return the number of probed devices,
i.e. either 1 or 0. However, i2sbus_add_dev() has one error handling
that returns -ENODEV; this will screw up the accumulation number
counted in the caller, i2sbus_probe().
Fix the return value to 0 and add the comment for better understanding
for readers.
Fixes: f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Link: https://lore.kernel.org/r/20221027065233.13292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The current code for freeing the emux timer is extremely dangerous:
CPU0 CPU1
---- ----
snd_emux_timer_callback()
snd_emux_free()
spin_lock(&emu->voice_lock)
del_timer(&emu->tlist); <-- returns immediately
spin_unlock(&emu->voice_lock);
[..]
kfree(emu);
spin_lock(&emu->voice_lock);
[BOOM!]
Instead just use del_timer_sync() which will wait for the timer to finish
before continuing. No need to check if the timer is active or not when
doing so.
This doesn't fix the race of a possible re-arming of the timer, but at
least it won't use the data that has just been freed.
[ Fixed unused variable warning by tiwai ]
Cc: stable@vger.kernel.org
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221026231236.6834b551@gandalf.local.home
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
dev_set_name() in soundbus_add_one() allocates memory for name, it need be
freed when of_device_register() fails, call soundbus_dev_put() to give up
the reference that hold in device_initialize(), so that it can be freed in
kobject_cleanup() when the refcount hit to 0. And other resources are also
freed in i2sbus_release_dev(), so it can return 0 directly.
Fixes: f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221027013438.991920-1-yangyingliang@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.1
Quite a few fixes here, a lot driver specific, plus some new quirks.
There was a bit of a mess with the runtime PM handling due to some
confusion in the API there which resulted in a number of commits and
reverts but that should all be stable now.
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
msm-fixes for v6.1
- Fix shrinker deadlock
- Fix crash during suspend after unbind
- Fix IRQ lifetime issues
- Fix potential memory corruption with too many bridges
- Fix memory corruption on GPU state capture
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGveadezhqm=Sra7Jq4A3tFAp_eBmKKOoHLnapN03pVoLw@mail.gmail.com
|
|
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-25
The 1st patch adds a missing cleanup call in the error path of the
probe function in mpc5xxx glue code for the mscan driver.
The 2nd patch adds a missing cleanup call in the error path of the
probe function of the mcp251x driver.
* tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
====================
Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix some aspects of building with an older (than the one in the
kernel sources) libbpf present in a distro, when building with
LIBBPF_DYNAMIC=1.
- Fix errno setting races with event_fd and the signal handler in 'perf
record'.
- Fix Power10 hv-24x7 metric events when some events may have a zero
count based on system configuration.
- Do not fail Intel-PT misc test w/o libpython, just skip it.
- Fix incorrect arm64 Hisi hip08 L3 metrics (IF_BP_MISP_BR_RET,
IF_BP_MISP_BR_RET, IF_BP_MISP_BR_BL) due to mistakes in the
documentation used to generate the JSON files for these metrics.
- Fix auxtrace (Intel PT, ARM Coresight) address filter symbol name
match for modules, we need to skip the module name.
- Sync copies of files with the kernel sources, including ppc syscall
tables and assorted headers, some resulting in tools being able to
decode new network protocols (IPPROTO_L2TP) and statx masks
(STATX_DIOALIGN).
- Fix PMU name pai_crypto in the vendor events file (JSON) for s390.
- Fix man page build wrt perf-arm-coresight.txt as the build process
assumes files starting with 'perf-' are man pages, and this file
isn't one.
* tag 'perf-tools-fixes-for-v6.1-2022-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
perf auxtrace: Fix address filter symbol name match for modules
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
tools headers cpufeatures: Sync with the kernel sources
tools headers uapi: Sync linux/stat.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers uapi: Update linux/in.h copy
tools headers: Update the copy of x86's memcpy_64.S used in 'perf bench'
tools headers arm64: Sync arm64's cputype.h with the kernel sources
perf test: Do not fail Intel-PT misc test w/o libpython
perf list: Fix PMU name pai_crypto in perf list on s390
perf record: Fix event fd races
perf bpf: Fix build with libbpf 0.7.0 by checking if bpf_program__set_insns() is available
perf bpf: Fix build with libbpf 0.7.0 by adding prototype for bpf_load_program()
perf vendor events power10: Fix hv-24x7 metric events
perf docs: Fix man page build wrt perf-arm-coresight.txt
tools headers UAPI: Sync powerpc syscall tables with the kernel sources
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
|
|
In the S2idle suspend/resume phase the gfxoff is keeping functional so
some IP blocks will be likely to reinitialize at gfxoff entry and that
will result in failing to program GC registers.Therefore, let disallow
gfxoff until AMDGPU IPs reinitialized completely.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15.x
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- fix for Page Table mem leak
- defconfig updates
- misc other fixes
* tag 'arc-6.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: fix leakage of memory allocated for PTE
arc: update config files
arc: iounmap() arg is volatile
arc: dts: Harmonize EHCI/OHCI DT nodes name
ARC: bitops: Change __fls to return unsigned long
ARC: Fix comment typo
ARC: Fix comment typo
|
|
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3
metrics") add L3 metrics of hip08, but some metrics (IF_BP_MISP_BR_RET,
IF_BP_MISP_BR_RET, IF_BP_MISP_BR_BL) have incorrect event number due to
the mistakes in document, which caused incorrect result. Fix the
incorrect metrics.
Before:
65,811,214,308 armv8_pmuv3_0/event=0x1014/ # 18.87 push_branch
# -40.19 other_branch
3,564,316,780 BR_MIS_PRED # 0.51 indirect_branch
# 21.81 pop_branch
After:
6,537,146,245 BR_MIS_PRED # 0.48 indirect_branch
# 0.47 pop_branch
# 0.00 push_branch
# 0.05 other_branch
Fixes: 0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3 metrics")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: James Clark <james.clark@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221021105035.10000-2-shangxiaojing@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
For modules, names from kallsyms__parse() contain the module name which
meant that module symbols did not match exactly by name.
Fix by matching the name string up to the separating tab character.
Fixes: 1b36c03e356936d6 ("perf record: Add support for using symbols in address filters")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026072736.2982-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
