| Age | Commit message (Collapse) | Author |
|---|
|
After all, this is what it is there for.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Which is that the level2_kernel_pgt (__ka virtual addresses)
and level2_ident_pgt (__va virtual address) contain the same
PMD entries. So if you modify a PTE in __ka, it will be reflected
in __va (and vice-versa).
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
We don't need to return the new PGD - as we do not use it.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
and "xen/x86: Use memblock_reserve for sensitive areas."
This reverts commit 806c312e50f122c47913145cf884f53dd09d9199 and
commit 59b294403e9814e7c1154043567f0d71bac7a511.
And also documents setup.c and why we want to do it that way, which
is that we tried to make the the memblock_reserve more selective so
that it would be clear what region is reserved. Sadly we ran
in the problem wherein on a 64-bit hypervisor with a 32-bit
initial domain, the pt_base has the cr3 value which is not
neccessarily where the pagetable starts! As Jan put it: "
Actually, the adjustment turns out to be correct: The page
tables for a 32-on-64 dom0 get allocated in the order "first L1",
"first L2", "first L3", so the offset to the page table base is
indeed 2. When reading xen/include/public/xen.h's comment
very strictly, this is not a violation (since there nothing is said
that the first thing in the page table space is pointed to by
pt_base; I admit that this seems to be implied though, namely
do I think that it is implied that the page table space is the
range [pt_base, pt_base + nt_pt_frames), whereas that
range here indeed is [pt_base - 2, pt_base - 2 + nt_pt_frames),
which - without a priori knowledge - the kernel would have
difficulty to figure out)." - so lets just fall back to the
easy way and reserve the whole region.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Small platform specific bug fixes for problems found in randconfig builds.
* randconfig/mach:
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.
Without this patch, building without LEDS_CLASS esults in:
drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'
This reverts 8733f53c6 "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.
In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
|
|
The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.
Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.
Without this patch, building imx5 standalone results in:
arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org
|
|
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
|
|
The ksz9021rn_phy_fixup and mx6q_sabrelite functions try to
set up an ethernet phy if they can. They do check whether
phylib is enabled, but unfortunately the functions can only
be called from platform code if phylib is builtin, not
if it is a module
Without this patch, building with a modular phylib results in:
arch/arm/mach-imx/mach-imx6q.c: In function 'imx6q_sabrelite_init':
arch/arm/mach-imx/mach-imx6q.c:120:5: error: 'ksz9021rn_phy_fixup' undeclared (first use in this function)
arch/arm/mach-imx/mach-imx6q.c:120:5: note: each undeclared identifier is reported only once for each function it appears in
The bug was originally reported by Artem Bityutskiy but only
partially fixed in ef441806 "ARM: imx6q: register phy fixup only when
CONFIG_PHYLIB is enabled".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This moves the imx5 pm code out of the list of unconditionally
compiled files for imx5, mirroring what we already do for imx6
and how it was done before the code was move from mach-mx5 to
mach-imx in v3.3.
Without this patch, building with CONFIG_PM disabled results in:
arch/arm/mach-imx/pm-imx5.c:202:116: error: redefinition of 'imx51_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:154:91: note: previous definition of 'imx51_pm_init' was here
arch/arm/mach-imx/pm-imx5.c:209:116: error: redefinition of 'imx53_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:155:91: note: previous definition of 'imx53_pm_init' was here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
|
|
The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.
This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.
Without this patch, building rand-0y2jSKT results in:
drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]
It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@linaro.org>:
Here are two audio fixes for the ux500 found by Lee Jones.
* tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim <kgene.kim@samsung.com>:
For HDMI, already HDMI support for EXYNOS in mainline kernel is broken
because its configuration moved to platform data but regarding platform
data didn't support yet. And others are for fix warnings.
* 'v3.6-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set HDMI platform data in Origen board
ARM: EXYNOS: Set HDMI platform data in SMDKV310
ARM: SAMSUNG: Add API to set platform data for s5p-tv driver
ARM: SAMSUNG: Set HDMI platform data for Exynos4x12 SoCs
ARM: Samsung: Make uart_save static in pm.c file
ARM: S3C24XX: Fix s3c2410_dma_enqueue parameters
ARM: S3C24XX: Add missing DMACH_DT_PROP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
pointer.
arch/x86/xen/pci-swiotlb-xen.c:96:1: warning: Using plain integer as NULL pointer
arch/x86/xen/pci-swiotlb-xen.c:96:1: warning: Using plain integer as NULL pointer
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Sparse warns us off:
drivers/xen/swiotlb-xen.c:506:1: warning: symbol 'xen_swiotlb_map_sg' was not declared. Should it be static?
drivers/xen/swiotlb-xen.c:534:1: warning: symbol 'xen_swiotlb_unmap_sg' was not declared. Should it be static?
and it looks like we do not need this function at all.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
This patch removes the "return -ENOSYS" for auto_translated_physmap
guests from privcmd_mmap, thus it allows ARM guests to issue privcmd
mmap calls. However privcmd mmap calls are still going to fail for HVM
and hybrid guests on x86 because the xen_remap_domain_mfn_range
implementation is currently PV only.
Changes in v2:
- better commit message;
- return -EINVAL from xen_remap_domain_mfn_range if
auto_translated_physmap.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
All the original Xen headers have xen_pfn_t as mfn and pfn type, however
when they have been imported in Linux, xen_pfn_t has been replaced with
unsigned long. That might work for x86 and ia64 but it does not for arm.
Bring back xen_pfn_t and let each architecture define xen_pfn_t as they
see fit.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Reset the IRQ_NOAUTOEN and IRQ_NOREQUEST flags that are enabled by
default on ARM. If IRQ_NOAUTOEN is set, __setup_irq doesn't call
irq_startup, that is responsible for calling irq_unmask at startup time.
As a result event channels remain masked.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
When unmask_evtchn is called, if we already have an event pending, we
just set evtchn_pending_sel waiting for local_irq_enable to be called.
That is because PV guests set the irq_enable pvops to
xen_irq_enable_direct in xen_setup_vcpu_info_placement:
xen_irq_enable_direct is implemented in assembly in
arch/x86/xen/xen-asm.S and call xen_force_evtchn_callback if
XEN_vcpu_info_pending is set.
However HVM guests (and ARM guests) do not change or do not have the
irq_enable pvop, so evtchn_unmask cannot work properly for them.
Considering that having the pending_irq bit set when unmask_evtchn is
called is not very common, and it is simpler to keep the
native_irq_enable implementation for HVM guests (and ARM guests), the
best thing to do is just use the EVTCHNOP_unmask hypercall (Xen
re-injects pending events in response).
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
This hypercall has been present since Xen 3.1, and is the preferred
method for a domain to obtain its UUID. Fall back to the xenstore method
if using an older version of Xen (which returns -ENOSYS).
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
When we are finished with return PFNs to the hypervisor, then
populate it back, and also mark the E820 MMIO and E820 gaps
as IDENTITY_FRAMEs, we then call P2M to set areas that can
be used for ballooning. We were off by one, and ended up
over-writting a P2M entry that most likely was an IDENTITY_FRAME.
For example:
1-1 mapping on 40000->40200
1-1 mapping on bc558->bc5ac
1-1 mapping on bc5b4->bc8c5
1-1 mapping on bc8c6->bcb7c
1-1 mapping on bcd00->100000
Released 614 pages of unused memory
Set 277889 page(s) to 1-1 mapping
Populating 40200-40466 pfn range: 614 pages added
=> here we set from 40466 up to bc559 P2M tree to be
INVALID_P2M_ENTRY. We should have done it up to bc558.
The end result is that if anybody is trying to construct
a PTE for PFN bc558 they end up with ~PAGE_PRESENT.
CC: stable@vger.kernel.org
Reported-by-and-Tested-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller". Fix binding doc and dts
to get them match driver code.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
Though commit 602bf40 (ARM: imx6: exit coherency when shutting down
a cpu) improves the stability of imx6q cpu hotplug a lot, there are
still hangs seen with a more stressful hotplug testing.
It's expected that once imx_enable_cpu(cpu, false) is called, the cpu
will be taken down by hardware immediately, and the code after that
will not get any chance to execute. However, this is not always the
case from the testing. The cpu could possibly be alive for a few
cycles before hardware actually takes it down. So rather than letting
cpu execute some code that could cause a hang in these cycles, let's
make the cpu spin there and wait for hardware to take it down.
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Remove the malformed "mem=" bootargs parameter in at91sam9g25ek.dts
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fix PLLA overclock warning in relation with datasheet numbers.
Add new > 240 MHz and > 210 MHz SoC categories.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset. It modifies rtc-at91sam9 driver in
order to get irq from resources.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
omapfb does not currently set pseudo palette correctly for color depths
above 16bpp, making red text invisible, command like
echo -e '\e[0;31mRED' > /dev/tty1
will display nothing on framebuffer console in 24bpp mode.
This is because temporary variable is declared incorrectly, fix it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: stable@vger.kernel.org # v3.x
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Commit f476ae9dab3234532d41d36beb4ba7be838fa786 (OMAPDSS: APPLY: Remove
DISPC writes to manager's lcd parameters in interface) broke the SDI
output, as it causes the SDI PLL locking to fail.
LCLK and PCLK divisors are located in shadow registers, and we normally
write them to DISPC registers when enabling the output. However, SDI
uses pck-free as source clock for its PLL, and pck-free is affected by
the divisors. And as we need the PLL before enabling the output, we need
to write the divisors early.
It seems just writing to the DISPC register is enough, and we don't need
to care about the shadow register mechanism for pck-free. The exact
reason for this is unknown.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Do a sanity check on these before using them as divisors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Using kfree to free data allocated with devm_kzalloc causes double frees.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Switch to kmalloc(,GFP_ATOMIC) in bit_putcs to fix below trace:
[ 9.771812] BUG: sleeping function called from invalid context at /usr/src/linux-git/mm/slub.c:943
[ 9.771814] in_atomic(): 1, irqs_disabled(): 1, pid: 1063, name: mount
[ 9.771818] Pid: 1063, comm: mount Not tainted 3.5.0-jupiter-00003-g8d858b1-dirty #2
[ 9.771819] Call Trace:
[ 9.771838] [<c104f79b>] __might_sleep+0xcb/0xe0
[ 9.771844] [<c10c00d4>] __kmalloc+0xb4/0x1c0
[ 9.771851] [<c1041d4a>] ? queue_work+0x1a/0x30
[ 9.771854] [<c1041dcf>] ? queue_delayed_work+0xf/0x30
[ 9.771862] [<c1205832>] ? bit_putcs+0xf2/0x3e0
[ 9.771865] [<c1041e01>] ? schedule_delayed_work+0x11/0x20
[ 9.771868] [<c1205832>] bit_putcs+0xf2/0x3e0
[ 9.771875] [<c12002b8>] ? get_color.clone.14+0x28/0x100
[ 9.771878] [<c1200d2f>] fbcon_putcs+0x11f/0x130
[ 9.771882] [<c1205740>] ? bit_clear+0xe0/0xe0
[ 9.771885] [<c1200f6d>] fbcon_redraw.clone.21+0x11d/0x160
[ 9.771889] [<c120383d>] fbcon_scroll+0x79d/0xe10
[ 9.771892] [<c12002b8>] ? get_color.clone.14+0x28/0x100
[ 9.771897] [<c124c0b4>] scrup+0x64/0xd0
[ 9.771900] [<c124c22b>] lf+0x2b/0x60
[ 9.771903] [<c124cc95>] vt_console_print+0x1d5/0x2f0
[ 9.771907] [<c124cac0>] ? register_vt_notifier+0x20/0x20
[ 9.771913] [<c102b335>] call_console_drivers.clone.5+0xa5/0xc0
[ 9.771916] [<c102c58e>] console_unlock+0x2fe/0x3c0
[ 9.771920] [<c102ca16>] vprintk_emit+0x2e6/0x300
[ 9.771924] [<c13f01ae>] printk+0x38/0x3a
[ 9.771931] [<c112e8fe>] reiserfs_remount+0x2ae/0x3e0
[ 9.771934] [<c112e650>] ? reiserfs_fill_super+0xb00/0xb00
[ 9.771939] [<c10ca0ab>] do_remount_sb+0xab/0x150
[ 9.771943] [<c1034476>] ? ns_capable+0x46/0x70
[ 9.771948] [<c10e059c>] do_mount+0x20c/0x6b0
[ 9.771955] [<c10a7044>] ? strndup_user+0x34/0x50
[ 9.771958] [<c10e0acc>] sys_mount+0x6c/0xa0
[ 9.771964] [<c13f2557>] sysenter_do_call+0x12/0x26
According to comment in bit_putcs() that kammloc() call only happens
when fbcon is drawing to a monochrome framebuffer (which is my case with
hid-picolcd).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Commit 91f68c89d8f3 ("block: fix infinite loop in __getblk_slow")
is not good: a successful call to grow_buffers() cannot guarantee
that the page won't be reclaimed before the immediate next call to
__find_get_block(), which is why there was always a loop there.
Yesterday I got "EXT4-fs error (device loop0): __ext4_get_inode_loc:3595:
inode #19278: block 664: comm cc1: unable to read itable block" on console,
which pointed to this commit.
I've been trying to bisect for weeks, why kbuild-on-ext4-on-loop-on-tmpfs
sometimes fails from a missing header file, under memory pressure on
ppc G5. I've never seen this on x86, and I've never seen it on 3.5-rc7
itself, despite that commit being in there: bisection pointed to an
irrelevant pinctrl merge, but hard to tell when failure takes between
18 minutes and 38 hours (but so far it's happened quicker on 3.6-rc2).
(I've since found such __ext4_get_inode_loc errors in /var/log/messages
from previous weeks: why the message never appeared on console until
yesterday morning is a mystery for another day.)
Revert 91f68c89d8f3, restoring __getblk_slow() to how it was (plus
a checkpatch nitfix). Simplify the interface between grow_buffers()
and grow_dev_page(), and avoid the infinite loop beyond end of device
by instead checking init_page_buffers()'s end_block there (I presume
that's more efficient than a repeated call to blkdev_max_block()),
returning -ENXIO to __getblk_slow() in that case.
And remove akpm's ten-year-old "__getblk() cannot fail ... weird"
comment, but that is worrying: are all users of __getblk() really
now prepared for a NULL bh beyond end of device, or will some oops??
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # 3.0 3.2 3.4 3.5
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This is already fixed for ILK and SNB in the below commit but somehow
IVB is missed.
commit ab2f9df10dd955f1fc0a8650e377588c98f1c029
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Feb 27 12:40:10 2012 -0800
drm/i915: fix color order for BGR formats on SNB
Had the wrong bits and field definitions.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.
This bug was indroduced by
commit 1519b9956eb4b4180fa3f47c73341463cdcfaa37
Author: Keith Packard <keithp@keithp.com>
Date: Sat Aug 6 10:35:34 2011 -0700
drm/i915: Fix PCH port pipe select in CPT disable paths
The reachable tag for this commit is v3.1-rc1-3-g1519b99
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44876
Tested-by: Daniel Schroeder <sec@dschroeder.info>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The old interface is bugged and reads the wrong sensor when retrieving
the reading for the chassis fan (it reads the CPU sensor); the new
interface works fine.
Reported-by: Göran Uddeborg <goeran@uddeborg.se>
Cc: stable@vger.kernel.org
Tested-by: Göran Uddeborg <goeran@uddeborg.se>
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sylvain Munault reported following info :
- TCP connection get "stuck" with data in send queue when doing
"large" transfers ( like typing 'ps ax' on a ssh connection )
- Only happens on path where the PMTU is lower than the MTU of
the interface
- Is not present right after boot, it only appears 10-20min after
boot or so. (and that's inside the _same_ TCP connection, it works
fine at first and then in the same ssh session, it'll get stuck)
- Definitely seems related to fragments somehow since I see a router
sending ICMP message saying fragmentation is needed.
- Exact same setup works fine with kernel 3.5.1
Problem happens when the 10 minutes (ip_rt_mtu_expires) expiration
period is over.
ip_rt_update_pmtu() calls dst_set_expires() to rearm a new expiration,
but dst_set_expires() does nothing because dst.expires is already set.
It seems we want to set the expires field to a new value, regardless
of prior one.
With help from Julian Anastasov.
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Julian Anastasov <ja@ssi.bg>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This issue was recently observed on an AMD C-50 CPU where a patch of
maximum size was applied.
Commit be62adb49294 ("x86, microcode, AMD: Simplify ucode verification")
added current_size in get_matching_microcode(). This is calculated as
size of the ucode patch + 8 (ie. size of the header). Later this is
compared against the maximum possible ucode patch size for a CPU family.
And of course this fails if the patch has already maximum size.
Cc: <stable@vger.kernel.org> [3.3+]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-1-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The sub-register used to access the stack (sp, esp, or rsp) is not
determined by the address size attribute like other memory references,
but by the stack segment's B bit (if not in x86_64 mode).
Fix by using the existing stack_mask() to figure out the correct mask.
This long-existing bug was exposed by a combination of a27685c33acccce
(emulate invalid guest state by default), which causes many more
instructions to be emulated, and a seabios change (possibly a bug) which
causes the high 16 bits of esp to become polluted across calls to real
mode software interrupts.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
|
|
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull drm fixes from Dave Airlie:
"Intel: edid fixes, power consumption fix, s/r fix, haswell fix
Radeon: BIOS loading fixes for UEFI and Thunderbolt machines, better
MSAA validation, lockup timeout fixes, modesetting fixes
One udl dpms fix, one vmwgfx fix, a couple of trivial core changes.
There is an export added to ACPI as part of the radeon bios fixes.
I've also included the fbcon flashing cursor vs deinit race fix, that
seems the simplest place to start"
Trivial conflict in drivers/video/console/fbcon.c due to me having
already applied the fbcon flashing cursor vs deinit race fix, and Dave
had added a comment in there too.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
fbcon: fix race condition between console lock and cursor timer (v1.1)
drm: Add missing static storage class specifiers in drm_proc.c file
drm/udl: dpms off the crtc when disabled.
drm: Remove two unused fields from struct drm_display_mode
drm: stop vmgfx driver explosion
drm/radeon/ss: use num_crtc rather than hardcoded 6
Revert "drm/radeon: fix bo creation retry path"
drm/i915: use hsw rps tuning values everywhere on gen6+
drm/radeon: split ATRM support out from the ATPX handler (v3)
drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
ACPI: export symbol acpi_get_table_with_size
drm/radeon: implement ACPI VFCT vbios fetch (v3)
drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
drm/radeon: fix checking of MSAA renderbuffers on r600-r700
drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
drm/radeon: init lockup timeout on ring init
drm/radeon: avoid turning off spread spectrum for used pll
drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
drm/i915: extract connector update from intel_ddc_get_modes() for reuse
drm/i915: fix hsw uncached pte
...
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"The executive summary includes:
- Post-merge review comments for tcm_vhost (MST + nab)
- Avoid debugging overhead when not debugging for tcm-fc(FCoE) (MDR)
- Fix NULL pointer dereference bug on alloc_page failulre (Yi Zou)
- Fix REPORT_LUNs regression bug with pSCSI export (AlexE + nab)
- Fix regression bug with handling of zero-length data CDBs (nab)
- Fix vhost_scsi_target structure alignment (MST)
Thanks again to everyone who contributed a bugfix patch, gave review
feedback on tcm_vhost code, and/or reported a bug during their own
testing over the last weeks.
There is one other outstanding bug reported by Roland recently related
to SCSI transfer length overflow handling, for which the current
proposed bugfix has been left in queue pending further testing with
other non iscsi-target based fabric drivers.
As the patch is verified with loopback (local SGL memory from SCSI
LLD) + tcm_qla2xxx (TCM allocated SGL memory mapped to PCI HW) fabric
ports, it will be included into the next 3.6-rc-fixes PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Remove unused se_cmd.cmd_spdtl
tcm_fc: rcu_deref outside rcu lock/unlock section
tcm_vhost: Fix vhost_scsi_target structure alignment
target: Fix regression bug with handling of zero-length data CDBs
target/pscsi: Fix bug with REPORT_LUNs handling for SCSI passthrough
tcm_vhost: Change vhost_scsi_target->vhost_wwpn to char *
target: fix NULL pointer dereference bug alloc_page() fails to get memory
tcm_fc: Avoid debug overhead when not debugging
tcm_vhost: Post-merge review changes requested by MST
tcm_vhost: Fix incorrect IS_ERR() usage in vhost_scsi_map_iov_to_sgl
|
|
git://git.pengutronix.de/git/wsa/linux
Pull i2c-embedded fixes from Wolfram Sang:
"Some bugfixes for the "embedded" part of the I2C subsystem. The fixes
affect mostly drivers which have been largely reworked lately and
where regressions appeared."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: protect suspend/resume callbacks with CONFIG_PM_SLEEP
i2c: diolan-u2c: Fix master_xfer return code
I2C: OMAP: xfer: fix runtime PM get/put balance on error
i2c: nomadik: Add default configuration into the Nomadik I2C driver
|
