Age | Commit message (Collapse) | Author |
|
Enable the PCIe0 PHY to be able to set calibrations read from eFuses,
improving the stability and performance of the PCIe link.
While at it, also enable the T-PHYs for both PCIe1 and for USB, allowing
the USB ports to finally switch to gadget mode if needed, and configure
the VBUS/ID pins of both USB ports for the same.
Link: https://lore.kernel.org/r/20240409114211.310462-5-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
The paris pinctrl driver supports specifying the RSEL drive strength
in microamperes as well as internal bits definitions: choose to specify
those in uA to avoid using hardware specific values in device trees.
Link: https://lore.kernel.org/r/20240409114211.310462-4-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
GPIOs 25 and 26 do not support pull-up/pull-down when those are muxed
as I2C6's SDA6/SCL6 lines: set those to bias-disable to avoid warning
messages from the pinctrl driver.
Fixes: 96564b1e2ea4 ("arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board")
Link: https://lore.kernel.org/r/20240409114211.310462-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
The thermal zones in MT8183 had cryptic names and all of them, apart
from the cpu-thermal zone, had no thermal trips, hence those were not
probed at all.
Refactor the tzts1..5 and tztsABB thermal zones to add the correct
thermal trips and give them a meaningful name, corresponding to the
actually monitored thermal zone.
While at it, also rename the thermal sensor node to "thermal-sensor".
Now the thermal zones are probing and their temperatures can be read.
Fixes: b325ce39785b ("arm64: dts: mt8183: add thermal zone node")
Link: https://lore.kernel.org/r/20240410083002.1357857-4-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
This SoC has two GPU related thermal zones: the primary zone must be
called "gpu-thermal" for SVS to pick it up.
Fixes: c7a728051f4e ("arm64: dts: mediatek: mt8192: Add thermal nodes and thermal zones")
Link: https://lore.kernel.org/r/20240410083002.1357857-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
This SoC has two GPU related thermal zones: the primary zone must be
called "gpu-thermal" for SVS to pick it up.
Fixes: 1e5b6725199f ("arm64: dts: mediatek: mt8195: Add AP domain thermal zones")
Link: https://lore.kernel.org/r/20240410083002.1357857-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-2-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
1. Add compatible for MT8390.
2. Add bindings for the MediaTek mt8390-evk board, also known
as the "Genio 700-EVK".
The MT8390 and MT8188 belong to the same SoC family,
with only minor differences in their physical characteristics.
They utilize unique efuse values for differentiation.
The booting process and configurations are managed by boot
loaders, firmware, and TF-A. Consequently, the part numbers
and procurement channels vary.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230915081212.13959-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
MT7981 (Filogic 820) is a low cost version of MT7986 (Filogic 830) with
the same watchdog controller. It also comes with on-SoC 802.11ax
wireless.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240221085547.27840-1-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Add bindings of two on-SoC XHCI controllers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240213130044.1976-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Add compatible for MT8188 VPP mutex, having different bits to activate
mute for various hardware IPs.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240322092845.381313-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
None of the MT8192 Chromebooks had their chassis-type specified: add
the right definition for each.
Reviewed-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20240313141538.1438167-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Define the chassis type on the remaining MT8183 Chromebooks.
Link: https://lore.kernel.org/r/20240313141538.1438167-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Introduce the Airoha EN7581 SoC's dtsi and the Airoha EN7581 Evaluation
Board's dts file, as well as the required Makefiles.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/f05a36dd7e8ef34ead8a63aa10fcffb542229404.1709975956.git.lorenzo@kernel.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Introduce Airoha EN7581 entry in Airoha dts binding.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/ee9cda964dac62d38d1c239f7b189f707d3708a0.1709975956.git.lorenzo@kernel.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router. It
has 256 MiB of RAM, some LEDs & buttons and (not described yet) 4
Ethernet ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-5-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
MT7981 contains on-SoC PIN controller that is also a GPIO provider.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-4-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Cudy WR3000 V1 is an MT7981B (AKA Filogic 820) based wireless router.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-3-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
Cudy is a Chinese company providing networking products.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240317223206.22033-2-zajec5@gmail.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The core gains placeholders for recently added functions when
CONFIG_I2C is not defined as well documentation fixes to start using
inclusive terminology.
The drivers get paths in DT bindings fixed as well as proper interrupt
handling for the ocores driver"
* tag 'i2c-for-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: summary: be clearer with 'controller/target' and 'adapter/client' pairs
docs: i2c: summary: document 'local' and 'remote' targets
docs: i2c: summary: document use of inclusive language
docs: i2c: summary: update speed mode description
docs: i2c: summary: update I2C specification link
docs: i2c: summary: start sentences consistently.
i2c: Add nop fwnode operations
i2c: ocores: set IACK bit after core is enabled
dt-bindings: i2c: google,cros-ec-i2c-tunnel: correct path to i2c-controller schema
dt-bindings: i2c: atmel,at91sam: correct path to i2c-controller schema
|
|
Pull smb client fixes from Steve French:
"Five smb3 client fixes
- three nets/fiolios cifs fixes
- fix typo in module parameters description
- fix incorrect swap warning"
* tag '6.10-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Move the 'pid' from the subreq to the req
cifs: Only pick a channel once per read request
cifs: Defer read completion
cifs: fix typo in module parameter enable_gcm_256
cifs: drop the incorrect assertion in cifs_swap_rw()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fix from Mike Rapoport:
"Fix fragility in checks for unset node ID.
Use numa_valid_node() function to verify that nid is a valid node
ID instead of inconsistent comparisons with either NUMA_NO_NODE or
MAX_NUMNODES"
* tag 'fixes-2024-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: use numa_valid_node() helper to check for invalid node ID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix lseek in o32 compat mode
- fix for microMIPS MT ASE helpers
* tag 'mips-fixes_6.10_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: fix compat_sys_lseek syscall
MIPS: mipsmtregs: Fix target register for MFTC0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- An ARM-relevant fix to not free default RMIDs of a resource control
group
- A randconfig build fix for the VMware virtual GPU driver
* tag 'x86_urgent_for_v6.10_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Don't try to free nonexistent RMIDs
drm/vmwgfx: Fix missing HYPERVISOR_GUEST dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Prevent use-after-free in 64-bit KVM VFIO
- Add generated Power8 crypto asm to .gitignore
Thanks to Al Viro and Nathan Lynch.
* tag 'powerpc-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
powerpc/crypto: Add generated P8 asm to .gitignore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
This pull request fixes the paths of the dt-schema to their
complete locations for the ChromeOS EC tunnel driver and the
Atmel at91sam drivers.
Additionally, the OpenCores driver receives a fix for an issue
that dates back to version 2.6.18. Specifically, the interrupts
need to be acknowledged (clearing all pending interrupts) after
enabling the core.
|
|
Pull rust fix from Miguel Ojeda:
- Avoid unused import warning in 'rusttest'.
* tag 'rust-fixes-6.10' of https://github.com/Rust-for-Linux/linux:
rust: avoid unused import warning in `rusttest`
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few driver specific fixes for incorrect device descriptions, plus a
fix for a missing symbol export which causes build failures for some
newly added drivers in other trees"
* tag 'regulator-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: AXP717: fix LDO supply rails and off-by-ones
regulator: bd71815: fix ramp values
regulator: core: Fix modpost error "regulator_get_regmap" undefined
regulator: tps6594-regulator: Fix the number of irqs for TPS65224 and TPS6594
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A number of fixes that have built up for SPI, a bunch of driver
specific ones including an unfortunate revert of an optimisation for
the i.MX driver which was causing issues with some configurations,
plus a couple of core fixes for the rarely used octal mode and for a
bad interaction between multi-CS support and target mode"
* tag 'spi-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-imx: imx51: revert burst length calculation back to bits_per_word
spi: Fix SPI slave probe failure
spi: Fix OCTAL mode support
spi: stm32: qspi: Clamp stm32_qspi_get_mode() output to CCR_BUSWIDTH_4
spi: stm32: qspi: Fix dual flash mode sanity test in stm32_qspi_setup()
spi: cs42l43: Drop cs35l56 SPI speed down to 11MHz
spi: cs42l43: Correct SPI root clock speed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Fix crashes triggered by administrative operations on the server
* tag 'nfsd-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: grab nfsd_mutex in nfsd_nl_rpc_status_get_dumpit()
nfsd: fix oops when reading pool_stats before server is started
|
|
Pull xfs fix from Chandan Babu:
- Fix assertion failure due to a race between unlink and cluster buffer
instantiation.
* tag 'xfs-6.10-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix unlink vs cluster buffer instantiation race
|
|
Pull bcachefs fixes from Kent Overstreet:
"Lots of (mostly boring) fixes for syzbot bugs and rare(r) CI bugs.
The LRU_TIME_BITS fix was slightly more involved; we only have 48 bits
for the LRU position (we would prefer 64), so wraparound is possible
for the cached data LRUs on a filesystem that has done sufficient
(petabytes) reads; this is now handled.
One notable user reported bugfix, where we were forgetting to
correctly set the bucket data type, which should have been
BCH_DATA_need_gc_gens instead of BCH_DATA_free; this was causing us to
go emergency read-only on a filesystem that had seen heavy enough use
to see bucket gen wraparoud.
We're now starting to fix simple (safe) errors without requiring user
intervention - i.e. a small incremental step towards full self
healing.
This is currently limited to just certain allocation information
counters, and the error is still logged in the superblock; see that
patch for more information. ("bcachefs: Fix safe errors by default")"
* tag 'bcachefs-2024-06-22' of https://evilpiepirate.org/git/bcachefs: (22 commits)
bcachefs: Move the ei_flags setting to after initialization
bcachefs: Fix a UAF after write_super()
bcachefs: Use bch2_print_string_as_lines for long err
bcachefs: Fix I_NEW warning in race path in bch2_inode_insert()
bcachefs: Replace bare EEXIST with private error codes
bcachefs: Fix missing alloc_data_type_set()
closures: Change BUG_ON() to WARN_ON()
bcachefs: fix alignment of VMA for memory mapped files on THP
bcachefs: Fix safe errors by default
bcachefs: Fix bch2_trans_put()
bcachefs: set_worker_desc() for delete_dead_snapshots
bcachefs: Fix bch2_sb_downgrade_update()
bcachefs: Handle cached data LRU wraparound
bcachefs: Guard against overflowing LRU_TIME_BITS
bcachefs: delete_dead_snapshots() doesn't need to go RW
bcachefs: Fix early init error path in journal code
bcachefs: Check for invalid btree IDs
bcachefs: Fix btree ID bitmasks
bcachefs: Fix shift overflow in read_one_super()
bcachefs: Fix a locking bug in the do_discard_fast() path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Niklas Cassel:
- We currently enable DIPM (device initiated power management) in the
device (using a SET FEATURES call to the device), regardless if the
HBA supports any LPM states or not. It seems counter intuitive, and
potentially dangerous to enable a device side feature, when the HBA
does not have the corresponding support. Thus, make sure that we do
not enable DIPM if the HBA does not support any LPM states.
* tag 'ata-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Do not enable LPM if no LPM states are supported by the HBA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Three fixes for the pwm-stm32 driver.
The first patch prevents an integer wrap-around for small periods. In
the second patch the calculation of the prescaler is fixed which
resulted in values for the ARR register that don't fit into the
corresponding register bit field. The last commit improves an error
message that was wrongly copied from another error path"
* tag 'pwm/for-6.10-rc5-fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: stm32: Fix error message to not describe the previous error path
pwm: stm32: Fix calculation of prescaler
pwm: stm32: Refuse too small period requests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"There are seven oneline patches that each address a distinct problem
on the NXP i.MX platform, mostly the popular i.MX8M variant.
The only other two fixes are for error handling on the psci firmware
driver and SD card support on the milkv duo riscv board"
* tag 'arm-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: psci: Fix return value from psci_system_suspend()
riscv: dts: sophgo: disable write-protection for milkv duo
arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
arm64: dts: freescale: imx8mm-verdin: enable hysteresis on slow input pin
arm64: dts: imx93-11x11-evk: Remove the 'no-sdio' property
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix BT shutdown GPIO
arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting node
arm64: dts: imx8mp: Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM
arm64: dts: freescale: imx8mm-verdin: Fix GPU speed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Some hw breakpoint fixes, an objtool build warnging fix, and a trivial
cleanup"
* tag 'loongarch-fixes-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Remove an unneeded semicolon
LoongArch: Fix multiple hardware watchpoint issues
LoongArch: Trigger user-space watchpoints correctly
LoongArch: Fix watchpoint setting error
LoongArch: Only allow OBJTOOL & ORC unwinder if toolchain supports -mthin-add-sub
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix dangling references to a redistributor region if the vgic was
prematurely destroyed.
- Properly mark FFA buffers as released, ensuring that both parties
can make forward progress.
x86:
- Allow getting/setting MSRs for SEV-ES guests, if they're using the
pre-6.9 KVM_SEV_ES_INIT API.
- Always sync pending posted interrupts to the IRR prior to IOAPIC
route updates, so that EOIs are intercepted properly if the old
routing table requested that.
Generic:
- Avoid __fls(0)
- Fix reference leak on hwpoisoned page
- Fix a race in kvm_vcpu_on_spin() by ensuring loads and stores are
atomic.
- Fix bug in __kvm_handle_hva_range() where KVM calls a function
pointer that was intended to be a marker only (nothing bad happens
but kind of a mine and also technically undefined behavior)
- Do not bother accounting allocations that are small and freed
before getting back to userspace.
Selftests:
- Fix compilation for RISC-V.
- Fix a "shift too big" goof in the KVM_SEV_INIT2 selftest.
- Compute the max mappable gfn for KVM selftests on x86 using
GuestMaxPhyAddr from KVM's supported CPUID (if it's available)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: Fix svm_get_msr()/svm_set_msr() for KVM_SEV_ES_INIT guests
KVM: Discard zero mask with function kvm_dirty_ring_reset
virt: guest_memfd: fix reference leak on hwpoisoned page
kvm: do not account temporary allocations to kmem
MAINTAINERS: Drop Wanpeng Li as a Reviewer for KVM Paravirt support
KVM: x86: Always sync PIR to IRR prior to scanning I/O APIC routes
KVM: Stop processing *all* memslots when "null" mmu_notifier handler is found
KVM: arm64: FFA: Release hyp rx buffer
KVM: selftests: Fix RISC-V compilation
KVM: arm64: Disassociate vcpus from redistributor region on teardown
KVM: Fix a data race on last_boosted_vcpu in kvm_vcpu_on_spin()
KVM: selftests: x86: Prioritize getting max_gfn from GuestPhysBits
KVM: selftests: Fix shift of 32 bit unsigned int more than 32 bits
|
|
"Failed to lock the clock" is an appropriate error message for
clk_rate_exclusive_get() failing, but not for the clock running too
fast for the driver's calculations.
Adapt the error message accordingly.
Fixes: d44d635635a7 ("pwm: stm32: Fix for settings using period > UINT32_MAX")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/285182163211203fc823a65b180761f46e828dcb.1718979150.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
|
A small prescaler is beneficial, as this improves the resolution of the
duty_cycle configuration. However if the prescaler is too small, the
maximal possible period becomes considerably smaller than the requested
value.
One situation where this goes wrong is the following: With a parent
clock rate of 208877930 Hz and max_arr = 0xffff = 65535, a request for
period = 941243 ns currently results in PSC = 1. The value for ARR is
then calculated to
ARR = 941243 * 208877930 / (1000000000 * 2) - 1 = 98301
This value is bigger than 65535 however and so doesn't fit into the
respective register field. In this particular case the PWM was
configured for a period of 313733.4806027616 ns (with ARR = 98301 &
0xffff). Even if ARR was configured to its maximal value, only period =
627495.6861167669 ns would be achievable.
Fix the calculation accordingly and adapt the comment to match the new
algorithm.
With the calculation fixed the above case results in PSC = 2 and so an
actual period of 941229.1667195285 ns.
Fixes: 8002fbeef1e4 ("pwm: stm32: Calculate prescaler with a division instead of a loop")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/b4d96b79917617434a540df45f20cb5de4142f88.1718979150.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
|
|
pairs
This not only includes rewording, but also where to put which emphasis
on terms in this document.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Because Linux can be a target as well, add terminology to differentiate
between Linux being the target and Linux accessing targets.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
We now have the updated I2C specs and our own Code of Conduct, so we
have all we need to switch over to the inclusive terminology. Define
them here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Fastest I2C mode is 5 MHz. Update the docs and reword the paragraph
slightly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Luckily, the specs are directly downloadable again, so update the link.
Also update its title to the original name "I²C".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Change the first paragraphs to contain only one space after the end of
the previous sentence like in the rest of the document.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: usb: uas: Do not query the IO Advice Hints Grouping mode page for USB/UAS devices
scsi: core: Introduce the BLIST_SKIP_IO_HINTS flag
scsi: ufs: core: Free memory allocated for model before reinit
|
|
Pull drm fixes from Dave Airlie:
"Still pretty quiet, two weeks worth of amdgpu fixes, with one i915 and
one xe. I didn't get the drm-misc-fixes tree PR this week, but there
was only one fix queued and I think it can wait another week, so seems
pretty normal.
xe:
- Fix for invalid register access
i915:
- Fix conditions for joiner usage, it's not possible with eDP MSO
amdgpu:
- Fix display idle optimization race
- Fix GPUVM TLB flush locking scope
- IPS fix
- GFX 9.4.3 harvesting fix
- Runtime pm fix for shared buffers
- DCN 3.5.x fixes
- USB4 fix
- RISC-V clang fix
- Silence UBSAN warnings
- MES11 fix
- PSP 14.0.x fix"
* tag 'drm-fixes-2024-06-22' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe/vf: Don't touch GuC irq registers if using memory irqs
drm/amdgpu: init TA fw for psp v14
drm/amdgpu: cleanup MES11 command submission
drm/amdgpu: fix UBSAN warning in kv_dpm.c
drm/radeon: fix UBSAN warning in kv_dpm.c
drm/amd/display: Disable CONFIG_DRM_AMD_DC_FP for RISC-V with clang
drm/amd/display: Attempt to avoid empty TUs when endpoint is DPIA
drm/amd/display: change dram_clock_latency to 34us for dcn35
drm/amd/display: Change dram_clock_latency to 34us for dcn351
drm/amdgpu: revert "take runtime pm reference when we attach a buffer" v2
drm/amdgpu: Indicate CU havest info to CP
drm/amd/display: prevent register access while in IPS
drm/amdgpu: fix locking scope when flushing tlb
drm/amd/display: Remove redundant idle optimization check
drm/i915/mso: using joiner is not possible with eDP MSO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix two bugs, one originating in this cycle and one from 6.6"
* tag 'ovl-fixes-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix encoding fid for lower only root
ovl: fix copy-up in tmpfile
|
|
Pull io_uring fix from Jens Axboe:
"Just a single cleanup for the fixed buffer iov_iter import.
More cosmetic than anything else, but let's get it cleaned up as it's
confusing"
* tag 'io_uring-6.10-20240621' of git://git.kernel.dk/linux:
io_uring/rsrc: fix incorrect assignment of iter->nr_segs in io_import_fixed
|