| Age | Commit message (Collapse) | Author |
|---|
|
disable-gpio is an (old) downstream kernel property, which slipped into
DT. Remove it.
Fixes: c01a26b8897a ("arm64: dts: mba8xx: Add PCIe support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
IRQ mapping is already present. Add the missing DMA interrupt. This is
similar to commit 9d9c56025e429 ("arm64: dts: imx8-ss-hsio: Wire up DMA
IRQ for PCIe")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move port@0 and port@1 under ports to fix below DTB_CHECK warnings.
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dtb: usb@38100000: port@0:reg:0:0: 0 is less than the minimum of 1
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dtb: usb@38100000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'dr_mode', 'phy-names', 'phys', 'port@0', 'port@1', 'snps,parkmode-disable-ss-quirk' were unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same model name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same model name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add FlexCAN[0..3] for S32G2 and S32G3 SoCs.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add imx95-15x15-evk support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i3c1 and i3c2 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add #io-channel-cells = <1> for adc node.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This board is very similar to the already upstream
imx8mp-skov-revb-mi1010ait-1cp1.dts with the difference that it uses a
different 7" LVDS panel.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The BD500 replaces the touch display with 3 bicolor LEDs and a push
button on top of a Skov i.MX8-CPU revision C.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
I2C bus recovery can be used to recover when SCL/SDA are stuck low.
To be able to use it, add the necessary GPIO and pinctrl entries.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
I2C2 is exposed on a pin header on the base board, so its pinmux is
always the same if it's enabled.
Therefore, move the definition to the common DTSI, so board DTs only
need to override the status to enable it.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
All Skov i.MX8MP boards share the same baseboard (modulo revisions)
and are booted with the same bootloader image, which samples some
strapping pins at startup and determines which kernel device tree
to use.
For use as bootloader device tree and as fallback, when no matching
device tree has been found, add a basic variant that doesn't configure
any variant-specific peripherals like displays.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To reduce heat generation, the Skov i.MX8MP boards should run in nominal
drive mode with a VDD_SOC voltage of 850 mV.
At this operating point, not all frequencies that are achievable with
overdrive mode are possible, so import imx8mp-nominal.dtsi to clock down
the clocks.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The comment in the DT mentions that "currently it is not possible to let
display clocks configure automatically, so we need to set them manually".
Since commit ff06ea04e4cf ("clk: imx: clk-imx8mp: Allow media_disp pixel
clock reconfigure parent rate"), this is no longer the case.
Make use of this new functionality by dropping the now unneeded
assigned-clock-rates in &media_blk_ctrl.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx8mp-nominal.dtsi is meant to be included into boards that want to
override the default overdrive clock settings with settings suitable for
running in nominal drive mode at its lower required voltage.
Specifying fsl,operating-mode = "nominal" informs drivers of this fact,
so they can sanity check runtime clock reconfiguration to observe the
limits imposed by nominal mode.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Unlike the i.MX8MM and i.MX8MN SoCs added earlier, the device tree for
the i.MX8MP configures some clocks at frequencies that are only validated
for overdrive mode, i.e. when VDD_SOC is 950 mV.
Boards may want to run their SoC at the lower voltage of 850 mV though
to reduce heat generation and power usage. For this to work, clock rates
need to adhere to the limits of the nominal drive mode.
Add an optional DTSI file which can be included by various boards to run
in this mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A lot of other clocks on the i.MX8MP, including the DRAM set up by the
bootloader are already running at overdrive clock rates. While this is a
deviation from the configuration of other i.MX8M* family SoCs, overdrive
is the default for most i.MX8MP boards and only some special purpose
boards will choose to run the SoC at nominal drive rates. Up the GPU and
NPU clock rates to their overdrive level to be consistent with other
clocks set up in the dtsi.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A device tree binding for the Microchip USB5744 hub controller
was added in commit 02be19e914b8 ("dt-bindings: usb: Add support
for Microchip usb5744 hub controller").
U-Boot will consume this binding in order to perform the
necessary actions to enable the USB hub ports over I2C.
(We previously used our own out-of-tree driver for
this task)
The Ten64 board does not have any switchable supplies
for the voltage rails utilized by the USB5744, so a
pair of dummy supplies have been added to facilitate
operation with U-Boot's hub driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are SoM variants with no SPI NOR flash populated. Add overlay to be
able to support this.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are SoM variants with no eth phy populated. Add overlay to be
able to support this.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adds a devicetree overlay containing reserved memory regions used
for intercore communication between A53 and M4 cores.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the PEB-EVAL-01 expansion board for
phyBOARD-Polis-i.MX8MM.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PEB-AV-10 is an Audio/Video extension module which extends
phyBOARD-Polis i.MX8MM.
With MIPI DSI to LVDS bridge already populated on SoM the PEB-AV-10 adds
support for:
- connecting 10" display,
- audio with TLV320AIC and
- EEPROM.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Assign the missing regulator to the bluetooth node. Absence of
this regulator triggers the warning message from kernel as driver
uses a fallback dummy regulator when there is no regulator assigned.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move properties from SoM's dtsi to carrierboard's dts as they are
actually defined by the carrier board design.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RV-3028 RTC can be used to wakeup the system on phyGATE-Tauri-L-i.MX8MM,
mark the device as wakeup source.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RV-3028 RTC can be used to wakeup the system on phyBOARD-Polis-i.MX8MM,
mark the device as wakeup source.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add RTC description.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing EEPROM and RTC descriptions. Also use eMMC with
lower-case "e".
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a missing voltage regulator of 1.8v to the sn65dsi83
(dsi_lvds bridge) node. Due to the absence of this regulator, a fallback
dummy regulator is used and that triggers a warning message from the
kernel. Assigning the appropriate regulator avoids the warning.
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove device tree property "fsl,magic-packet" as WoL is not working
on the SoM and so not required. This also saves a significant amount of
power during suspend as the ethernet phy is not powered down otherwise.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Not using pull-up on the host wake-up line triggers the wake up
immediately after device enters suspend. Fix this by enabling internal
pull-up and setting interrupt triggering on the falling edge.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LDO3 is also used as switch for enabling VDD_3V3_S and need to
be kept on during suspend. Disabling this can lead to an unwanted
reset during resume.
Set LDO3 to 2,5V as the voltage should be fix.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove LVDS panel and backlight nodes from the Verdin iMX8M Mini SoM
dtsi file, those two hardware components are not part of the SoM,
therefore they should not be present in this file.
This is solving a dtb checker warning about panel-lvds compatible.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing gpio-line-names for SODIMM_79 and SODIMM_97
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the two eDMA nodes in the device tree in order to enable the probing
of the S32G2/S32G3 eDMA driver.
Signed-off-by: Larisa Grigore <larisa.grigore@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe's msi-map and iommu-map property because i.MX95 support smmu and
its.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe EP overlay file for i.MX8QXP mek board to let PCI work as endpoint
mode.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe EP support for i.MX8QM and i.MX8QXP.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix indentation in pcie node.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
(Q)SPI NOR flash is supplied by 1.8V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, HDMI audio cannot play sound at a 44.1 kHz sample rate due to
a clock frequency mismatch. This update resolves the issue by allowing
the sai driver to change the clock parent to AUDIO_PLL_1 when the sample
rate is 44.1 kHz. It also ensures that AUDIO_PLL_1 operates at the
correct frequency for this configuration.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add INA231 current sensor for S32G399A-RDB3 boards.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Create common part, s32gxxa-evb.dtsi and s32gxxa-rdb.dtsi, for S32G2/S32G3
RDB2\3 and EVB G2/G3 boards to avoid copy duplicate part in boards dts
file. Prepare to add other modules such as FlexCAN, DSPI easily in the
future.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add I2C[0..2] for S32G2 and S32G3 SoCs.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
