| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit fabf85e3ca15d5b94058f391dac8df870cdd427a which breaks
hotkey support on some other HP laptops. We'll try doing this differently
in 3.10.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
|
|
The type when timeout support was enabled, could not list all elements,
just the first ones which could fit into one netlink message: it just
did not continue listing after the first message.
Reported-by: Yoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Tested-by: Yoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since commit 6b923cb7188d46 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.
Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.
More generally, the transport header might not be in the skb head.
Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.
Reported-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: Vitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes 2 issues regarding bnx2x's status blocks:
1. ethtool -c caused corruption of status blocks in FW RAM.
2. when using multi-CoS, the configuration of the timeout values of
status blocks is incorrect, harming the coalescing of interrupts
for such CoSs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.
During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.
This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.
This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Shahed Shaikh says:
====================
This patch series contains bug fixes for -
* Loopback test failure while traffic is running.
* Tx timeout and subsequent firmware reset by removing check for
'(adapter->netdev->features & (NETIF_F_TSO | NETIF_F_TSO6)' from tx fast
path, as per Eric's suggestion.
* Typo in logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN. This results in
the following scenario:
A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
100 because the VLVFB pool enable bit for that VF was left set
instead of being cleared as it should be.
This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch actually reverts:
igb: Support using build_skb in the case that jumbo frames are disabled
The reason for reverting this patch is that it can lead to data corruption.
The following flow was pointed out by Ben Hutchings:
1. skb is forwarded to another device
2. Packet headers are modified and it's put into a queue
3. Second packet is received into the other half of this page
4. Page cannot be reused, so is DMA-unmapped
5. The DMA mapping was non-coherent, so unmap copies or invalidates
cache
The headers added in step 2 get trashed in step 5.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included changes:
- fix MAC address check in case of multiple mesh interfaces
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L1 data cache flush needs to be after highbank_set_cpu_jump call which
pollutes the cache with the l2x0_lock. This causes other cores to deadlock
waiting for the l2x0_lock. Moving the flush of the entire data cache after
highbank_set_cpu_jump fixes the problem. Use flush_cache_louis instead of
flush_cache_all are that is sufficient to flush only the L1 data cache.
flush_cache_louis did not exist when highbank_cpu_die was originally
written.
With PL310 errata 769419 enabled, a wmb is inserted into idle which takes
the l2x0_lock. This makes the problem much more easily hit and causes
reset to hang.
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit 3a366e614d0837d9fc23f78cdb1a1186ebc3387f.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Install the Hyper-V specific interrupt handler only when needed. This would
permit us to get rid of the Xen check. Note that when the vmbus drivers invokes
the call to register its handler, we are sure to be running on Hyper-V.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Link: http://lkml.kernel.org/r/1366299886-6399-1-git-send-email-kys@microsoft.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Fix a double locking bug caused when debug.kprobe-optimization=0.
While the proc_kprobes_optimization_handler locks kprobe_mutex,
wait_for_kprobe_optimizer locks it again and that causes a double lock.
To fix the bug, this introduces different mutex for protecting
sysctl parameter and locks it in proc_kprobes_optimization_handler.
Of course, since we need to lock kprobe_mutex when touching kprobes
resources, that is done in *optimize_all_kprobes().
This bug was introduced by commit ad72b3bea744 ("kprobes: fix
wait_for_kprobe_optimizer()")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The BUG_ON() directive is triggered probably due to a latency
modification following inclusion of commit c10d73671ad3 ("softirq:
reduce latencies"). This condition has not been met before 3.9-rc1 and
doesn't trigger without this patch.
We now make sure that DMA channel is idle before calling
atc_complete_all() which makes the BUG_ON() "protection" useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the following oops, which could be trigged by build the kernel
with many concurrent threads, under CONFIG_DEBUG_PAGEALLOC.
hpte_insert() might return -1, indicating that the bucket (primary here)
is full. We are not necessarily reporting a BUG in this case. Instead, we could
try repeatedly (try secondary, remove and try again) until we find a slot.
[ 543.075675] ------------[ cut here ]------------
[ 543.075701] kernel BUG at arch/powerpc/mm/hash_utils_64.c:1239!
[ 543.075714] Oops: Exception in kernel mode, sig: 5 [#1]
[ 543.075722] PREEMPT SMP NR_CPUS=16 DEBUG_PAGEALLOC NUMA pSeries
[ 543.075741] Modules linked in: binfmt_misc ehea
[ 543.075759] NIP: c000000000036eb0 LR: c000000000036ea4 CTR: c00000000005a594
[ 543.075771] REGS: c0000000a90832c0 TRAP: 0700 Not tainted (3.8.0-next-20130222)
[ 543.075781] MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 22224482 XER: 00000000
[ 543.075816] SOFTE: 0
[ 543.075823] CFAR: c00000000004c200
[ 543.075830] TASK = c0000000e506b750[23934] 'cc1' THREAD: c0000000a9080000 CPU: 1
GPR00: 0000000000000001 c0000000a9083540 c000000000c600a8 ffffffffffffffff
GPR04: 0000000000000050 fffffffffffffffa c0000000a90834e0 00000000004ff594
GPR08: 0000000000000001 0000000000000000 000000009592d4d8 c000000000c86854
GPR12: 0000000000000002 c000000006ead300 0000000000a51000 0000000000000001
GPR16: f000000003354380 ffffffffffffffff ffffffffffffff80 0000000000000000
GPR20: 0000000000000001 c000000000c600a8 0000000000000001 0000000000000001
GPR24: 0000000003354380 c000000000000000 0000000000000000 c000000000b65950
GPR28: 0000002000000000 00000000000cd50e 0000000000bf50d9 c000000000c7c230
[ 543.076005] NIP [c000000000036eb0] .kernel_map_pages+0x1e0/0x3f8
[ 543.076016] LR [c000000000036ea4] .kernel_map_pages+0x1d4/0x3f8
[ 543.076025] Call Trace:
[ 543.076033] [c0000000a9083540] [c000000000036ea4] .kernel_map_pages+0x1d4/0x3f8 (unreliable)
[ 543.076053] [c0000000a9083640] [c000000000167638] .get_page_from_freelist+0x6cc/0x8dc
[ 543.076067] [c0000000a9083800] [c000000000167a48] .__alloc_pages_nodemask+0x200/0x96c
[ 543.076082] [c0000000a90839c0] [c0000000001ade44] .alloc_pages_vma+0x160/0x1e4
[ 543.076098] [c0000000a9083a80] [c00000000018ce04] .handle_pte_fault+0x1b0/0x7e8
[ 543.076113] [c0000000a9083b50] [c00000000018d5a8] .handle_mm_fault+0x16c/0x1a0
[ 543.076129] [c0000000a9083c00] [c0000000007bf1dc] .do_page_fault+0x4d0/0x7a4
[ 543.076144] [c0000000a9083e30] [c0000000000090e8] handle_page_fault+0x10/0x30
[ 543.076155] Instruction dump:
[ 543.076163] 7c630038 78631d88 e80a0000 f8410028 7c0903a6 e91f01de e96a0010 e84a0008
[ 543.076192] 4e800421 e8410028 7c7107b4 7a200fe0 <0b000000> 7f63db78 48785781 60000000
[ 543.076224] ---[ end trace bd5807e8d6ae186b ]---
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Move the logic trying to insert hpte in __hash_page_huge() to an helper
function, so it could also be used by others.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
It seems that new_pte and rflags don't get changed in the repeating loop, so
move their assignment out of the loop.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Add a PCI quirk for VGA devices on Power to set the default VGA device.
Ensures a default VGA is always set if a graphics adapter is present,
even if firmware did not initialize it. If more than one graphics
adapter is present, ensure the one initialized by firmware is set
as the default VGA device. This ensures that X autoconfiguration
will work.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Powerpc initializes the DMA and IRQ information in pci_scan_child_bus()->
pcibios_fixup_bus()->pcibios_setup_bus_devices(). But for the devices
which are hotpluged, bus->is added has been set for the first scan of the
PCI-e bus, so the initialization code won't be called. Then the hotpluged
devices' driver will fail to load.
For example :
The PCI-e device 0001:03:00.0 is the Intel PCI-e e1000e network card, remove
it from the system:
# echo 1 > /sys/bus/pci/devices/0001\:03\:00.0/remove
# e1000e 0001:03:00.0 eth0: removed PHC
Rescan it from it's bus:
# echo 1 > /sys/bus/pci/devices/0001\:02\:00.0/rescan
...
e1000e 0001:03:00.0: Disabling ASPM L0s L1
e1000e 0001:03:00.0: No usable DMA configuration, aborting
e1000e: probe of 0001:03:00.0 failed with error -5
So we move the DMA & IRQ initialization code from pcibios_setup_devices() and
construct a new function pcibios_enable_device. We call this function in
pcibios_enable_device, which will be called by PCI-e rescan code. At the
meanwhile, we avoid the the impact on cardbus. I also validate this patch with
silicon's PCIe-sata which encounters the IRQ issue.
Signed-off-by: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hiroo Matsumoto <matsumoto.hiroo@jp.fujitsu.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This function has always been marked as __cpuinit, but is only called
from functions marked as __init and references an __initdata variable.
So change its annotation to __init.
Fixes this build warning:
WARNING: arch/powerpc/mm/built-in.o(.cpuinit.text+0x86): Section mismatch in reference from the function .fake_numa_create_new_node() to the variable .init.data:cmdline
The function __cpuinit .fake_numa_create_new_node() references
a variable __initdata cmdline.
If cmdline is only used by .fake_numa_create_new_node then
annotate cmdline with a matching annotation.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
The following commit breaks numa distance setup for old powerpc
systems that use form0 encoding in device tree.
commit 41eab6f88f24124df89e38067b3766b7bef06ddb
powerpc/numa: Use form 1 affinity to setup node distance
Device tree node /rtas/ibm,associativity-reference-points would
index into /cpus/PowerPCxxxx/ibm,associativity based on form0 or
form1 encoding detected by ibm,architecture-vec-5 property.
All modern systems use form1 and current kernel code is correct.
However, on older systems with form0 encoding, the numa distance
will get hard coded as LOCAL_DISTANCE for all nodes. This causes
task scheduling anomaly since scheduler will skip building numa
level domain (topmost domain with all cpus) if all numa distances
are same. (value of 'level' in sched_init_numa() will remain 0)
Prior to the above commit:
((from) == (to) ? LOCAL_DISTANCE : REMOTE_DISTANCE)
Restoring compatible behavior with this patch for old powerpc systems
with device tree where numa distance are encoded as form0.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This adds new debug feature information so that the DAWR can be
identified by userspace tools like GDB.
Unfortunately the DAWR doesn't sit nicely into the current description
that ptrace provides to userspace via struct ppc_debug_info. It doesn't
allow for specifying that only some ranges are possible or even the end
alignment constraints (DAWR only allows 512 byte wide ranges which can't
cross a 512 byte boundary).
After talking to Edjunior Machado (GDB ppc developer), it was decided
this was the best approach. Just mark it as debug feature DAWR and
tools like GDB can internally decide the constraints.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This patch adds a new line to /proc/interrupts to account for the
doorbell interrupts that each hardware thread has received. The total
interrupt count in /proc/stat will now also include doorbells.
# cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
16: 551 1267 281 175 XICS Level IPI
LOC: 2037 1503 1688 1625 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
CNT: 0 0 0 0 Performance monitoring interrupts
MCE: 0 0 0 0 Machine check exceptions
DBL: 42 550 20 91 Doorbell interrupts
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
Two small bug fixes for net/3.9 including the issue previously
discussed where allocation of netlink notifications can fail after
changes have been committed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Given a PCI device with multiple functions in a DDW capable slot, the
following situation can be encountered: When the first function sets a
64-bit DMA mask, enable_ddw() will be called and we can fail to properly
configure DDW (the most common reason being the new DMA window's size is
not large enough to map all of an LPAR's memory). With the recent
changes to DDW, we remove the base window in order to determine if the
new window is of sufficient size to cover an LPAR's memory. We correctly
replace the base window if we find that not to be the case. However,
once we go through and re-configured 32-bit DMA via the IOMMU, the next
function of the adapter will go through the same process. And since DDW
is a characteristic of the slot itself, we are most likely going to fail
again. But to determine we are going to fail the second slot, we again
remove the base window -- but that is now in-use by the first
function/driver, which might be issuing I/O already.
To close this window, keep a list of all the failed struct device_nodes
that have failed to configure DDW. If the current device_node is in that
list, just fail out immediately and fall back to 32-bit DMA without
doing any DDW manipulation.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
As Michael Ellerman mentioned, arch/powerpc/sysdev/msi_bitmap.c
already implemented bitmap to manage (alloc/free) MSI interrupts.
The patch intends to use that mechanism to manage MSI interrupts
for PowerNV platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Setup the HFSCR (Hypervisor Facility Status and Control Register) for POWER8
when running HV=1. The HFSCR is the same as the FSCR except it's for
hypervisors. It controls the available of various facilities in OS and
userspace levels. It also indicates the cause of a hypervisor facility
unavailable interrupt (although we are not using this here).
This patch sets the facilities Linux knows about incase the firmware doesn't.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Add SPR number and bit definitions for the HFSCR (Hypervisor Facility Status
and Control Register).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Currently ptrace_get_reg returns error as a value
what make impossible to tell whether it is a correct value or error code.
The patch adds a parameter which points to the real return data and
returns an error code.
As get_user_msr() never fails and it is used in multiple places so it has not
been changed by this patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This fixes these errors when building UP with CONFIG_KVM_BOOK3S_64_HV=y:
arch/powerpc/kvm/book3s_hv.c:1855:2: error: implicit declaration of function 'inhibit_secondary_onlining' [-Werror=implicit-function-declaration]
arch/powerpc/kvm/book3s_hv.c:1862:2: error: implicit declaration of function 'uninhibit_secondary_onlining' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
and this error (with CONFIG_KVM_BOOK3S_64=m, or a vmlinux link error
with CONFIG_KVM_BOOK3S_64=y):
ERROR: "smp_send_reschedule" [arch/powerpc/kvm/kvm.ko] undefined!
make[2]: *** [__modpost] Error 1
The fix for the link error is suboptimal; ideally we want a self_ipi()
function from irq.c, connected at least to the MPIC code, to initiate
an IPI to this cpu. The fix here at least lets the code build, and it
will work, just with interrupts being delayed sometimes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
remove cast for kmalloc/kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Signed-off-by: Alex Grad <alex.grad@gmail.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
When I submitted commit 6805ab6daa2b589fe3242d05ddc47a9dbb0c4eb1
("powerpc: drop unused Kconfig symbols") I apparently failed to notice
that my patch also made PREP_RESIDUAL and PPC_A2_DD2 unused. Drop these
now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
The last users of Kconfig symbol MPC10X_OPENPIC were removed in v2.6.27.
Its Kconfig entry can be removed now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
All users of Kconfig symbol 405EP were removed in release v2.6.27.
Remove this symbol (and a useless select of it) too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Untested. As this typo was introduced in v3.3, with commit
9d670280908013004f173b2b86414d9b6918511b ("powerpc: Split ICSWX ACOP and
PID processing"), which actually added PPC_ICSWX_PID, this surely needs
testing.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
The Kconfig symbol MAX_ACTIVE_REGIONS is unused. Commit
0ee332c1451869963626bf9cac88f165a90990e1 ("memblock: Kill
early_node_map[]") removed the only place were it was actually used. But
it did not remove its Kconfig entries (for powerpc and sh).
Remove those two entries (and the entry for metag, that popped up in
v3.9-rc1).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
PPC_PREP is marked as BROKEN since v2.6.15. Remove all PReP specific
code now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Commit c1fb6816fb1b78dd94b673b0fdaa9a7a16e97bd1 ("powerpc: Add
relocation on exception vector handlers") added two lines of code that
depend on the macro CONFIG_HVC_SCOM. That macro doesn't exist. Perhaps
it was intended to use CONFIG_PPC_SCOM here. But since
"maintence_interrupt" is a typo and there's nothing in arch/powerpc that
looks like maintenance_interrupt it seems best to just delete these
lines.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
The last user of Kconfig symbol 405GPR got removed in release v3.2.
Remove this symbol too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
The Kconfig symbol PCI_PERMEDIA got removed in v2.6.24, through commit
e6b6e3ffb9ee8926f9f2f7dc9147df73e27d5828 ("[POWERPC] Remove APUS support
from arch/ppc"). Remove its last occurrence.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
There is no Kconfig symbol PPC_WSP_COPRO. The select statement for it is
a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Refresh and set CONFIG_RD_LZMA=y.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This fixes the following checkpatch.pl warnings:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
+EXPORT_SYMBOL(kmap_prot);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
+EXPORT_SYMBOL(kmap_pte);
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
