summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-09-23ixgbe: Fix FCRTH value in VM-to-VM loopback modeMark Rustad
The 82599 and X540 datasheets require that FCRTH be "set" for Tx switching (VM-to-VM loopback) but it did not previously specify what the value should be set to. It has now been determined that the correct value is RXPBSIZE - (24*1024). This setting is also required for later devices. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Only clear adapter_stopped if ixgbe_setup_fc succeededMark Rustad
A logic error here results in the adapter_stopped flag only being cleared when ixgbe_setup_fc returns an error. Correct the logic. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Correct several flaws with with DCA setupMark Rustad
This change does two things. First, it makes it so that we always set the relaxed ordering bits related to the DCA registers even if DCA is not enabled. Second, it moves the configuration out of the ixgbe_down function and into the ixgbe_configure function before enabling the Rx and Tx rings. This ensures that DCA is configured correctly before starting to process packets. Thanks to Alex Duyck for this fix. CC: Alex Duyck <aduyck@mirantis.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add new X550EM SFP+ device IDMark Rustad
Add new device ID for X550EM device with SFPs. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Update ixgbe_disable_pcie_master flow for X550*Mark Rustad
This patch skips the PCI transactions pending check in ixgbe_disable_pcie_master. This is done to addresses a known HW issue where the PCI transactions pending bit sticks high when there are pending transactions. HW engineering instructed to workaround this issue by wait and then continue with our reset flow. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add small packet padding support for X550Mark Rustad
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which enables padding of small packets. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Correct setting of RDRXCTL register for X550* devicesMark Rustad
Setting the X550* RDRXCTL register should fall through into X540 and 82599, not 82598. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Correct error path in semaphore handlingMark Rustad
The timeout path is supposed to release the semaphore, so do that. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add I2C bus mux supportMark Rustad
Take control of an I2C mux that selects which SFP is attached to the I2C bus. The control of the mux is captured in the taking and releasing of the related semaphore. Because only port 1 can control the mux, port 1 always leaves the mux set to select port 0. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Limit SFP polling rateMark Rustad
Reduce the frequency of polling for SFP modules. Because the service task sometimes runs at high rates, we can poll for SFPs too often. When an SFP is not present, the I2C timeouts that result are very costly. So, prevent SFP polling from being done more than once every two seconds. To reduce latency, the poll time is cleared in a couple of cases to permit the next service task execution to poll the SFP module. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Allow SFP+ on more than 82598 and 82599Mark Rustad
Since SFP+ can be used with some X550 devices, permit them to be detected. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add logic to reset CS4227 when neededMark Rustad
On some hardware platforms, the CS4227 does not initialize properly. Detect those cases and reset it appropriately. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+Mark Rustad
Configures the CS4227 correctly for both 1G and 10G operation, by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It needs to be in this function because we need both the module type and the speed, and this is the only function in the init flow that knows the speed. In contrast, ixgbe_setup_sfp_modules_X550em() does not know the speed, so we can't do anything useful here. This is a fundamental difference from the previous flow, and is due to the way the CS4227 is implemented. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Add X550EM_x dual-speed SFP+ supportMark Rustad
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link code was moved from ixgbe_82599.c to ixgbe_common.c for use by X550EM. SFP MAC link code is added to x550EM. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Allow reduced delays during SFP detectionMark Rustad
Reduce the number of retries during PHY detection. This reduces pauses when no SFP is present. Once an SFP is detected, the normal retry count will be used. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23ixgbe: Clear I2C destination locationMark Rustad
Clear the destination location for I2C data initially so that the received data will not be affected by previous attempts. This could have returned wrong data in certain retry sequences. Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-09-23net/ethoc: support big-endian register layoutMax Filippov
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23net: davinci_emac: Add support for fixed-link PHYNeil Armstrong
In case the DaVinci Emac is directly connected to a non-mdio PHY/device, it should be possible to provide a fixed link configuration in the DT. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Driver: Vmxnet3: Extend register dump supportShrikrishna Khare
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Acked-by: Srividya Murali <smurali@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-09-22 This series contains updates to e1000, e1000e, igbvf, ixgbe, ixgbevf and fm10k. Jacob provides several updates for fm10k, which cleans up comments and most notably a fix for a corner case issue with the PF/VF mailbox code. The issue being fm10k_mbx_reset_work clears various states about the mailbox, but does not clear the Tx FIFO head/tail pointers. We also are not able to simply clear these pointers, as we would drop untransmitted messages without error. Also adds support for extra debug statistics, which provides the ability to see what the PF thinks the VF mailboxes look like. Don adds support for SFP+ in X550 and support for SCTP flow director filters SCTP mask. Francois Romieu dusts off the e1000 driver and removes some dead calls to e1000_init_eeprom_params(). Toshiaki Makita provides three patches to enable TSO for stacked VLAN's on e1000e, igbvf and ixgbevf. Mark provides the first of several ixgbe updates. First updates the driver to accept SFP not present error for all devices, since an SFP can still be inserted. Adds support for SFP insertion interrupt on X550EM devices with SPFs. Adds I2C combined operations on X550EM (not X550) devices. Moved the setting of lan_id to before any I2C eeprom access. Lastly, set the bit bang mode in the hardware when performing bit banding I2C operations on X550. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'bridge_external_fdb_aging'David S. Miller
Scott Feldman says: ==================== bridge: don't age out externally added FDB entries v3: Per davem review: add del_timer_sync on rocker port remove. v2: Per Jiri review comment: add BR_DEFAULT_AGEING_TIME to defines Siva originally proposed skipping externally added FDB entries in the bridge's FDB garbage collection func, and moving the ageing of externally added entries to the port driver/device. This broke rocker, since rocker didn't have a hardware (or software) mechanism for ageing out its learned FDB entries. This patchset reintroduces Siva's bridge driver patch to skip externally added entries and adds support in rocker so rocker can age out its own entries. Rocker does this using a software timer similar to the bridge's FDB garbage collection timer. Other switchdev devices/drivers can use this software timer method or program the device to nofity aged-out entries to the driver. Updated switchdev.txt documentation to reflect current state-of-the-art. This removes one more XXX todo comment in switchdev.txt. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23switchdev: update documentation on FDB ageing_timeScott Feldman
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23bridge: don't age externally added FDB entriesSiva Mannem
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Premkumar Jonnala <pjonnala@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: add FDB cleanup timerScott Feldman
Add a timer to each rocker switch to do FDB entry cleanup by ageing out expired entries. The timer scheduling algo is copied from the bridge driver, for the most part, to keep the firing of the timer to a minimum. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: adding port ageing_time for ageing out FDB entriesScott Feldman
Follow-up patcheset will allow user to change ageing_time, but for now just hard-code it to a fixed value (the same value used as the default for the bridge driver). Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23bridge: define some min/max/default ageing time constantsScott Feldman
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: store rocker_port in fdb key rather than pportScott Feldman
We'll need more info from rocker_port than just pport when we age out fdb entries, so store rocker_port rather than pport in each fdb entry. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23rocker: track when FDB entry is touched.Scott Feldman
The entry is touched once when created, and touched again for each update. The touched time is used to calculate FDB entry age. Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge branch 'cls_bpf-next'David S. Miller
Daniel Borkmann says: ==================== Minor cls_bpf updates Some minor updates resp. follow-ups on cls_bpf, please see individual patches for details. Will follow with the iproute2 patch after this series. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: further limit exec opcodes subsetDaniel Borkmann
Jamal suggested to further limit the currently allowed subset of opcodes that may be used by a direct action return code as the intention is not to replace the full action engine, but rather to have a minimal set that can be used in the fast-path on things like ingress for some features that cls_bpf supports. Classifiers can, of course, still be chained together that have direct action mode with those that have a full exec pass. For more complex scenarios that go beyond this minimal set here, the full tcf_exts_exec() path must be used. Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: make binding to classid optionalDaniel Borkmann
The binding to a particular classid was so far always mandatory for cls_bpf, but it doesn't need to be. Therefore, lift this restriction as similarly done in other classifiers. Only a couple of qdiscs make use of class from the tcf_result, others don't strictly care, so let the user choose his needs (those that read out class can handle situations where it could be NULL). An explicit check for tcf_unbind_filter() is also not needed here, as the previous r->class was 0, so the xchg() will return that and therefore a callback to the qdisc's unbind_tcf() is skipped. Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23cls_bpf: also dump TCA_BPF_FLAGSDaniel Borkmann
In commit 43388da42a49 ("cls_bpf: introduce integrated actions") we have added TCA_BPF_FLAGS. We can also retrieve this information from the prog, dump it back to user space as well. It's useful in tc when displaying/dumping filter info. Also, remove tp from cls_bpf_prog_from_efd(), came in as a conflict from a rebase and it's unused here (later work may add it along with a real user). Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23Merge tag 'arcnet-cleanup-v4.3-rc2' of git://git.pengutronix.de/git/mgr/linuxDavid S. Miller
Michael Grzeschik says: ==================== ARCNET: refactoring and cleanup This series cleans up the code in drivers/net/arcnet and include/uapi/linux/if_arcnet.h . It doesn't change the runtime behaviour of the code. Its only purpose is to improve the code maintenance and readability. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23sched, bpf: let stack handle !IFF_UP devs on bpf_clone_redirectDaniel Borkmann
Similarly as already the case in bpf_redirect()/skb_do_redirect() pair, let the stack deal with devs that are !IFF_UP. dev_forward_skb() as well as dev_queue_xmit() will free the skb and increment drop counter internally in such cases, so we can spare the condition in bpf_clone_redirect(). Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23ipv6 Use get_hash_from_flowi6 for rt6 hashTom Herbert
In rt6_info_hash_nhsfn replace the custom hashing over flowi6 that is using xor with a call to common function get_hash_from_flowi6. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-09-23arcnet: capmode: remove extra functionMichael Grzeschik
This patch cleans the capmode protocol module. It removes the obsolete function arcnet_cap_init and replaces printk with pr_info. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: arc-rawmode: reorder module functionsMichael Grzeschik
This patch moves the module_init and module_exit patches to the end of the file. It also replaces the printk with pr_info. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: com20020: replace magic numbers with readable macrosMichael Grzeschik
This patch replaces all magic numbers in the driver with proper named macros. For the case of XTOcfg and STARTIOcmd it introduces the new macros. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: reformat structs to C99 formatMichael Grzeschik
This patch changes the macro definitions to match the C99 formating. This improves the readability. Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: Remove unused arcnet_<I/O>w macrosJoe Perches
The word length macros are unused. Remove them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: Add com9026.h to standardize COM9026_REG_<foo>Joe Perches
Deduplicate the COM9026 registers. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: Remove function pointer macro indirectionsJoe Perches
It's clearer to use function pointer calls directly instead of the macro indirections of ARCRESET, ACOMMAND, ASTATUS, and AINTMASK. Remove the now unused macros too. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: com90xx: Use arcnet_readb/writeb routinesJoe Perches
Simplify and make consistent the current uses of readb/writeb by using the newly introduced arcnet_<I/O> equivalents. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: arc-rimi: Use arcnet_<I/O> routinesJoe Perches
Simplify and make consistent the current uses of readb/writeb by using the newly introduced arcnet_<I/O> equivalents. o Add new #defines for register offsets o Remove old #defines that included the ioaddr o Remove obfuscating macros by expanding them in-place where appropriate Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: arcdevice.h: Add arcnet_readb and arcnet_writebJoe Perches
Use the same indirection as the other arcnet_<I/O> macros. Neither of these new macros add the BUS_ALIGN use for 8 bit devices on 16 bit busses. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: com90xx: Use arcnet_<I/O> routinesJoe Perches
Simplify and make consistent the current uses of inb/outb by using the newly introduced arcnet_<I/O> equivalents. o Add new #defines for register offsets o Remove old #defines that included the ioaddr o Remove obfuscating macros by expanding them in-place where appropriate Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: com90io: Use arcnet_<I/O> routinesJoe Perches
Simplify and make consistent the current uses of inb/outb by using the newly introduced arcnet_<I/O> equivalents. o Add new #defines for register offsets o Remove old #defines that included the ioaddr o Remove obfuscating macros by expanding them in-place where appropriate Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: com20020: Use arcnet_<I/O> routinesJoe Perches
Simplify and make consistent the current uses of inb/outb by using the newly introduced arcnet_<I/O> equivalents. o Add new #defines for register offsets There is an register offset, 8, that is unnamed and used as-is. o Remove old #defines that included the ioaddr o Remove obfuscating macros by expanding them in-place where appropriate o Create static inline com20020_set_subaddress for the SET_SUBADR macro There is an unused arcnet config entry CONFIGSA100_CT6001 which added a special #define BUS_ALIGN which was introduced but never used in fullhist git tree commit 22cfce4b82b0 ("[ARCNET]: Fixes.") in Nov 2004 for Linux v2.6.10. This BUS_ALIGN #define tries to allow 8 bit devices to work on a 16 bit bus by aligning addresses to 16 bit boundaries. Move this currently unused CONFIG_SA1100_CT6001 BUS_ALIGN macro from com20020.h to arcdevice.h. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: Add arcnet_<I/O> macrosJoe Perches
arcnet uses an I/O scheme which can align I/O addresses to word boundaries on different architectures. Add arcnet specific macros which can hide this alignment calculation. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
2015-09-23arcnet: Make a char * array const char * constJoe Perches
Might as well be specific about the use of this array. Add a commment questioning the indexing too. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-28 07:45:17 +0000