| Age | Commit message (Collapse) | Author |
|---|
|
Fix build_skb for bm capable devices when they fall-back using swbm path
(e.g. when bm properties are configured in device tree but
CONFIG_MVNETA_BM_ENABLE is not set). In this case rx_offset_correction is
overwritten so we need to use it building skb instead of
MVNETA_SKB_HEADROOM directly
Fixes: 8dc9a0888f4c ("net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine")
Fixes: 0db51da7a8e9 ("net: mvneta: add basic XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tipc prefix for log messages generated by tipc was
removed in commit 07f6c4bc048a ("tipc: convert tipc reference
table to use generic rhashtable").
This is still a useful prefix so add it back.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-11-12
1) Merge mlx5-next for devlink reload and flowtable offloads dependencies
2) Devlink reload support
3) TC Flowtable offloads
4) Misc cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use r8168d_modify_extpage() also in rtl8168f_config_eee_phy() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when ibmveth receive a loopback packet, it reports an
ambiguous error message "tx: h_send_logical_lan failed with rc=-4"
because the hypervisor rejects those types of packets. This fix
detects loopback packet and assures the source packet's MAC address
matches the driver's MAC address before transmitting to the
hypervisor.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the TI DP83869 Gigabit ethernet phy
device.
The DP83869 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dt bindings for the TI dp83869 Gigabit ethernet phy
device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the kernel datapath, the upcall don't
include skb hash info relatived. That will introduce
some problem, because the hash of skb is important
in kernel stack. For example, VXLAN module uses
it to select UDP src port. The tx queue selection
may also use the hash in stack.
Hash is computed in different ways. Hash is random
for a TCP socket, and hash may be computed in hardware,
or software stack. Recalculation hash is not easy.
Hash of TCP socket is computed:
tcp_v4_connect
-> sk_set_txhash (is random)
__tcp_transmit_skb
-> skb_set_hash_from_sk
There will be one upcall, without information of skb
hash, to ovs-vswitchd, for the first packet of a TCP
session. The rest packets will be processed in Open vSwitch
modules, hash kept. If this tcp session is forward to
VXLAN module, then the UDP src port of first tcp packet
is different from rest packets.
TCP packets may come from the host or dockers, to Open vSwitch.
To fix it, we store the hash info to upcall, and restore hash
when packets sent back.
+---------------+ +-------------------------+
| Docker/VMs | | ovs-vswitchd |
+----+----------+ +-+--------------------+--+
| ^ |
| | |
| | upcall v restore packet hash (not recalculate)
| +-+--------------------+--+
| tap netdev | | vxlan module
+---------------> +--> Open vSwitch ko +-->
or internal type | |
+-------------------------+
Reported-at: https://mail.openvswitch.org/pipermail/ovs-dev/2019-October/364062.html
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-11-14:
amdgpu:
- Fix a potential crash in firmware parsing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114221354.3914-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- One fix to the dotclock dividers range for sun4i
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113142645.GA967172@gilmour.lan
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- MOCS table fixes for EHL and TGL
- Update Display's rawclock on resume
- GVT's dmabuf reference drop fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114055302.GA3564@intel.com
|
|
MarkLee says:
====================
Rework mt762x GDM setup flow
The mt762x GDM block is mainly used to setup the HW internal
rx path from GMAC to RX DMA engine(PDMA) and the packet
switching engine(PSE) is responsed to do the data forward
following the GDM configuration.
This patch set have three goals :
1. Integrate GDM/PSE setup operations into single function "mtk_gdm_config"
2. Refine the timing of GDM/PSE setup, move it from mtk_hw_init
to mtk_open
3. Enable GDM GDMA_DROP_ALL mode to drop all packet during the
stop operation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable GDM GDMA_DROP_ALL mode to drop all packet during the
stop operation. This is recommended by the mt762x HW design
to drop all packet from GMAC before stopping PDMA.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refine the timing of GDM/PSE setup, move it from mtk_hw_init
to mtk_open. This is recommended by the mt762x HW design to
do GDM/PSE setup only after PDMA has been started.
We exclude mt7628 in mtk_gdm_config function since it is a old IP
and there is no GDM/PSE block on it.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Integrate GDM/PSE setup operations into single function "mtk_gdm_config"
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't really need 10k species of reset. Remove everything except cold
reset which is what is actually used. Too bad the hardware designers
couldn't agree to use the same bit field for rev 1 and rev 2, so the
(*reset_cmd) function pointer is there to stay.
However let's simplify the prototype and give it a struct dsa_switch (we
want to avoid forward-declarations of structures, in this case struct
sja1105_private, wherever we can).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
PTP clock source for SJA1105 tc-taprio offload
This series makes the IEEE 802.1Qbv egress scheduler of the sja1105
switch use a time reference that is synchronized to the network. This
enables quite a few real Time Sensitive Networking use cases, since in
this mode the switch can offer its clients a TDMA sort of access to the
network, and guaranteed latency for frames that are properly scheduled
based on the common PTP time.
The driver needs to do a 2-part activity:
- Program the gate control list into the static config and upload it
over SPI to the switch (already supported)
- Write the activation time of the scheduler (base-time) into the
PTPSCHTM register, and set the PTPSTRTSCH bit.
- Monitor the activation of the scheduler at the planned time and its
health.
Ok, 3 parts.
The time-aware scheduler cannot be programmed to activate at a time in
the past, and there is some logic to avoid that.
PTPCLKCORP is one of those "black magic" registers that just need to be
written to the length of the cycle. There is a 40-line long comment in
the second patch which explains why.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tested using the following bash script and the tc from iproute2-next:
#!/bin/bash
set -e -u -o pipefail
NSEC_PER_SEC="1000000000"
gatemask() {
local tc_list="$1"
local mask=0
for tc in ${tc_list}; do
mask=$((${mask} | (1 << ${tc})))
done
printf "%02x" ${mask}
}
if ! systemctl is-active --quiet ptp4l; then
echo "Please start the ptp4l service"
exit
fi
now=$(phc_ctl /dev/ptp1 get | gawk '/clock time is/ { print $5; }')
# Phase-align the base time to the start of the next second.
sec=$(echo "${now}" | gawk -F. '{ print $1; }')
base_time="$(((${sec} + 1) * ${NSEC_PER_SEC}))"
tc qdisc add dev swp5 parent root handle 100 taprio \
num_tc 8 \
map 0 1 2 3 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S $(gatemask 7) 100000 \
sched-entry S $(gatemask "0 1 2 3 4 5 6") 400000 \
clockid CLOCK_TAI flags 2
The "state machine" is a workqueue invoked after each manipulation
command on the PTP clock (reset, adjust time, set time, adjust
frequency) which checks over the state of the time-aware scheduler.
So it is not monitored periodically, only in reaction to a PTP command
typically triggered from a userspace daemon (linuxptp). Otherwise there
is no reason for things to go wrong.
Now that the timecounter/cyclecounter has been replaced with hardware
operations on the PTP clock, the TAS Kconfig now depends upon PTP and
the standalone clocksource operating mode has been removed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PTPSTRTSCH and PTPSTOPSCH bits are actually readable and indicate
whether the time-aware scheduler is running or not. We will be using
that for monitoring the scheduler in the next patch, so refactor the PTP
command API in order to allow that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
v2: declare as (struct common_firmware_header *) type because
struct xxx_firmware_header inherits from it
When CE's ucode_id(8) is used to get sdma_hdr, we will be accessing an
unallocated amdgpu_firmware_info instance.
This issue appears on rhel7.7 with gcc 4.8.5. Newer compilers might have
optimized out such 'defined but not referenced' variable.
[ 1120.798564] BUG: unable to handle kernel NULL pointer dereference at 000000000000000a
[ 1120.806703] IP: [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1120.813693] PGD 80000002603ff067 PUD 271b8d067 PMD 0
[ 1120.818931] Oops: 0000 [#1] SMP
[ 1120.822245] Modules linked in: amdgpu(OE+) amdkcl(OE) amd_iommu_v2 amdttm(OE) amd_sched(OE) xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun bridge stp llc devlink ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat iptable_mangle iptable_security iptable_raw nf_conntrack libcrc32c ip_set nfnetlink ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc dm_mirror dm_region_hash dm_log dm_mod intel_pmc_core intel_powerclamp coretemp intel_rapl joydev kvm_intel eeepc_wmi asus_wmi kvm sparse_keymap iTCO_wdt irqbypass rfkill crc32_pclmul snd_hda_codec_realtek mxm_wmi ghash_clmulni_intel intel_wmi_thunderbolt iTCO_vendor_support snd_hda_codec_generic snd_hda_codec_hdmi aesni_intel lrw gf128mul glue_helper ablk_helper sg cryptd pcspkr snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd pinctrl_sunrisepoint pinctrl_intel soundcore acpi_pad mei_me wmi mei i2c_i801 pcc_cpufreq ip_tables ext4 mbcache jbd2 sd_mod crc_t10dif crct10dif_generic i915 i2c_algo_bit iosf_mbi drm_kms_helper e1000e syscopyarea sysfillrect sysimgblt fb_sys_fops ahci libahci drm ptp libata crct10dif_pclmul crct10dif_common crc32c_intel serio_raw pps_core drm_panel_orientation_quirks video i2c_hid
[ 1120.954136] CPU: 4 PID: 2426 Comm: modprobe Tainted: G OE ------------ 3.10.0-1062.el7.x86_64 #1
[ 1120.964390] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 1302 11/09/2015
[ 1120.973321] task: ffff991ef1e3c1c0 ti: ffff991ee625c000 task.ti: ffff991ee625c000
[ 1120.981020] RIP: 0010:[<ffffffffc0e3c9b3>] [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1120.990483] RSP: 0018:ffff991ee625f950 EFLAGS: 00010202
[ 1120.995935] RAX: 0000000000000002 RBX: ffff991edf6b2d38 RCX: ffff991edf6a0000
[ 1121.003391] RDX: 0000000000000000 RSI: ffff991f01d13898 RDI: ffffffffc110afb3
[ 1121.010706] RBP: ffff991ee625f9b0 R08: 0000000000000000 R09: 0000000000000000
[ 1121.018029] R10: 00000000000004c4 R11: ffff991ee625f64e R12: ffff991edf6b3220
[ 1121.025353] R13: ffff991edf6a0000 R14: 0000000000000008 R15: ffff991edf6b2d30
[ 1121.032666] FS: 00007f97b0c0b740(0000) GS:ffff991f01d00000(0000) knlGS:0000000000000000
[ 1121.041000] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1121.046880] CR2: 000000000000000a CR3: 000000025e604000 CR4: 00000000003607e0
[ 1121.054239] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1121.061631] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1121.068938] Call Trace:
[ 1121.071494] [<ffffffffc0e3dba8>] psp_hw_init+0x218/0x270 [amdgpu]
[ 1121.077886] [<ffffffffc0da3188>] amdgpu_device_fw_loading+0xe8/0x160 [amdgpu]
[ 1121.085296] [<ffffffffc0e3b34c>] ? vega10_ih_irq_init+0x4bc/0x730 [amdgpu]
[ 1121.092534] [<ffffffffc0da5c75>] amdgpu_device_init+0x1495/0x1c90 [amdgpu]
[ 1121.099675] [<ffffffffc0da9cab>] amdgpu_driver_load_kms+0x8b/0x2f0 [amdgpu]
[ 1121.106888] [<ffffffffc01b25cf>] drm_dev_register+0x12f/0x1d0 [drm]
[ 1121.113419] [<ffffffffa4dcdfd8>] ? pci_enable_device_flags+0xe8/0x140
[ 1121.120183] [<ffffffffc0da260a>] amdgpu_pci_probe+0xca/0x170 [amdgpu]
[ 1121.126919] [<ffffffffa4dcf97a>] local_pci_probe+0x4a/0xb0
[ 1121.132622] [<ffffffffa4dd10c9>] pci_device_probe+0x109/0x160
[ 1121.138607] [<ffffffffa4eb4205>] driver_probe_device+0xc5/0x3e0
[ 1121.144766] [<ffffffffa4eb4603>] __driver_attach+0x93/0xa0
[ 1121.150507] [<ffffffffa4eb4570>] ? __device_attach+0x50/0x50
[ 1121.156422] [<ffffffffa4eb1da5>] bus_for_each_dev+0x75/0xc0
[ 1121.162213] [<ffffffffa4eb3b7e>] driver_attach+0x1e/0x20
[ 1121.167771] [<ffffffffa4eb3620>] bus_add_driver+0x200/0x2d0
[ 1121.173590] [<ffffffffa4eb4c94>] driver_register+0x64/0xf0
[ 1121.179345] [<ffffffffa4dd0905>] __pci_register_driver+0xa5/0xc0
[ 1121.185593] [<ffffffffc099f000>] ? 0xffffffffc099efff
[ 1121.190914] [<ffffffffc099f0a4>] amdgpu_init+0xa4/0xb0 [amdgpu]
[ 1121.197101] [<ffffffffa4a0210a>] do_one_initcall+0xba/0x240
[ 1121.202901] [<ffffffffa4b1c90a>] load_module+0x271a/0x2bb0
[ 1121.208598] [<ffffffffa4dad740>] ? ddebug_proc_write+0x100/0x100
[ 1121.214894] [<ffffffffa4b1ce8f>] SyS_init_module+0xef/0x140
[ 1121.220698] [<ffffffffa518bede>] system_call_fastpath+0x25/0x2a
[ 1121.226870] Code: b4 01 60 a2 00 00 31 c0 e8 83 60 33 e4 41 8b 47 08 48 8b 4d d0 48 c7 c7 b3 af 10 c1 48 69 c0 68 07 00 00 48 8b 84 01 60 a2 00 00 <48> 8b 70 08 31 c0 48 89 75 c8 e8 56 60 33 e4 48 8b 4d d0 48 c7
[ 1121.247422] RIP [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1121.254432] RSP <ffff991ee625f950>
[ 1121.258017] CR2: 000000000000000a
[ 1121.261427] ---[ end trace e98b35387ede75bd ]---
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Fixes: c5fb912653dae3f878 ("drm/amdgpu: add firmware header printing for psp fw loading (v2)")
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The driver misses calling destroy_workqueue in remove like what is done
when probe fails.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is a bug that checking the same active_list over and over again
in iocg_activate(). The intention of the code was checking whether all
the ancestors and self have already been activated. So fix it.
Fixes: 7caa47151ab2 ("blkcg: implement blk-iocost")
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some versions of gcc (so far 6.3 and 7.4) throw a warning:
drivers/block/rbd.c: In function 'rbd_object_map_callback':
drivers/block/rbd.c:2124:21: warning: 'current_state' may be used uninitialized in this function [-Wmaybe-uninitialized]
(current_state == OBJECT_EXISTS && state == OBJECT_EXISTS_CLEAN))
drivers/block/rbd.c:2092:23: note: 'current_state' was declared here
u8 state, new_state, current_state;
^~~~~~~~~~~~~
It's bogus because all current_state accesses are guarded by
has_current_state.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
|
|
Ceph can in some cases issue an async DIO request, in which case we can
end up calling ceph_end_io_direct before the I/O is actually complete.
That may allow buffered operations to proceed while DIO requests are
still in flight.
Fix this by incrementing the i_dio_count when issuing an async DIO
request, and decrement it when tearing down the aio_req.
Fixes: 321fe13c9398 ("ceph: add buffered/direct exclusionary locking for reads and writes")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Most of the time, we (or the vfs layer) takes the inode_lock and then
acquires caps, but ceph_read_iter does the opposite, and that can lead
to a deadlock.
When there are multiple clients treading over the same data, we can end
up in a situation where a reader takes caps and then tries to acquire
the inode_lock. Another task holds the inode_lock and issues a request
to the MDS which needs to revoke the caps, but that can't happen until
the inode_lock is unwedged.
Fix this by having ceph_read_iter take the inode_lock earlier, before
attempting to acquire caps.
Fixes: 321fe13c9398 ("ceph: add buffered/direct exclusionary locking for reads and writes")
Link: https://tracker.ceph.com/issues/36348
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
The recently introduced unit descriptor validation had some bug for
processing and extension units, it counts a bControlSize byte twice so
it expected a bigger size than it should have been. This seems
resulting in a probe error on a few devices.
Fix the calculation for proper checks of PU and EU.
Fixes: 57f8770620e9 ("ALSA: usb-audio: More validations of descriptor units")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191114165613.7422-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix build error when compiling SPARC VDSO with CONFIG_COMPAT=y
- pass correct --arch option to Sparse
* tag 'kbuild-fixes-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: tell sparse about the $ARCH
sparc: vdso: fix build error of vdso32
|
|
Pull RDMA fixes from Jason Gunthorpe:
"Bug fixes for old bugs in the hns and hfi1 drivers:
- Calculate various values in hns properly to avoid over/underflows
in some cases
- Fix an oops, PCI negotiation on Gen4 systems, and bugs related to
retries"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Correct the value of srq_desc_size
RDMA/hns: Correct the value of HNS_ROCE_HEM_CHUNK_LEN
IB/hfi1: TID RDMA WRITE should not return IB_WC_RNR_RETRY_EXC_ERR
IB/hfi1: Calculate flow weight based on QP MTU for TID RDMA
IB/hfi1: Ensure r_tid_ack is valid before building TID RDMA ACK packet
IB/hfi1: Ensure full Gen3 speed in a Gen4 system
|
|
Add new command for getting/setting current transmit power
and propagate requests from user space to firmware.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Report MIC failure from firmware to cfg80211 subsystem
using dedicated callback cfg80211_michael_mic_failure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Send EAPOL frames via control path so they can be treated in a different
way rather than normal data frames. In this case EAPOLs are sent with
higher priority and with disabled aggregation and encryption. Besides,
all devices benefit from sending EAPOL frames via high priority path,
so move the functionality from chip specific to common code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rx descriptors queue length is hardware specific. Current common default
value is no more than an accident. So move Rx descriptor queue setup to
platform PCIe backend in the same way as it is already done for Tx.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not attempt to print frequency for an invalid channel
provided by firmware. That channel may simply not exist.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix merge artifact for commit 0b68fe10b8e8 ("qtnfmac: modify debugfs
to support multiple cards") and finally add debugfs support
for multiple qtnfmac wireless cards.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
KASAN reported use-after-free error:
[ 995.220767] BUG: KASAN: use-after-free in qtnf_cmd_send_with_reply+0x169/0x3e0 [qtnfmac]
[ 995.221098] Read of size 2 at addr ffff888213d1ded0 by task kworker/1:1/71
The issue in qtnf_cmd_send_with_reply impacts all the commands that do
not need response other then return code. For such commands, consume_skb
is used for response skb and right after that return code in response
skb is accessed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
A number of people have reported the Edimax EW-7611ULB works fine.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Acquire the per-VM slots_lock when zapping all shadow pages as part of
toggling nx_huge_pages. The fast zap algorithm relies on exclusivity
(via slots_lock) to identify obsolete vs. valid shadow pages, because it
uses a single bit for its generation number. Holding slots_lock also
obviates the need to acquire a read lock on the VM's srcu.
Failing to take slots_lock when toggling nx_huge_pages allows multiple
instances of kvm_mmu_zap_all_fast() to run concurrently, as the other
user, KVM_SET_USER_MEMORY_REGION, does not take the global kvm_lock.
(kvm_mmu_zap_all_fast() does take kvm->mmu_lock, but it can be
temporarily dropped by kvm_zap_obsolete_pages(), so it is not enough
to enforce exclusivity).
Concurrent fast zap instances causes obsolete shadow pages to be
incorrectly identified as valid due to the single bit generation number
wrapping, which results in stale shadow pages being left in KVM's MMU
and leads to all sorts of undesirable behavior.
The bug is easily confirmed by running with CONFIG_PROVE_LOCKING and
toggling nx_huge_pages via its module param.
Note, until commit 4ae5acbc4936 ("KVM: x86/mmu: Take slots_lock when
using kvm_mmu_zap_all_fast()", 2019-11-13) the fast zap algorithm used
an ulong-sized generation instead of relying on exclusivity for
correctness, but all callers except the recently added set_nx_huge_pages()
needed to hold slots_lock anyways. Therefore, this patch does not have
to be backported to stable kernels.
Given that toggling nx_huge_pages is by no means a fast path, force it
to conform to the current approach instead of reintroducing the previous
generation count.
Fixes: b8e8c8303ff28 ("kvm: mmu: ITLB_MULTIHIT mitigation", but NOT FOR STABLE)
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Sparse uses the same executable for all archs and uses flags
like -m64, -mbig-endian or -D__arm__ for arch-specific parameters.
But Sparse also uses value from the host machine used to build
Sparse as default value for the target machine.
This works, of course, well for native build but can create
problems when cross-compiling, like defining both '__i386__'
and '__arm__' when cross-compiling for arm on a x86-64 machine.
Fix this by explicitely telling sparse the target architecture.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit 54b8ae66ae1a ("kbuild: change *FLAGS_<basetarget>.o to
take the path relative to $(obj)"), sparc allmodconfig fails to build
as follows:
CC arch/sparc/vdso/vdso32/vclock_gettime.o
unrecognized e_machine 18 arch/sparc/vdso/vdso32/vclock_gettime.o
arch/sparc/vdso/vdso32/vclock_gettime.o: failed
The cause of the breakage is that -pg flag not being dropped.
The vdso32 files are located in the vdso32/ subdirectory, but I missed
to update the Makefile.
I removed the meaningless CFLAGS_REMOVE_vdso-note.o since it is only
effective for C file.
vdso-note.o is compiled from assembly file:
arch/sparc/vdso/vdso-note.S
arch/sparc/vdso/vdso32/vdso-note.S
Fixes: 54b8ae66ae1a ("kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.
In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.
Fixes: 38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since commit 3726112ec731 ("block, bfq: re-schedule empty queues if
they deserve I/O plugging"), to prevent the service guarantees of a
bfq_queue from being violated, the bfq_queue may be left busy, i.e.,
scheduled for service, even if empty (see comments in
__bfq_bfqq_expire() for details). But, if no process will send
requests to the bfq_queue any longer, then there is no point in
keeping the bfq_queue scheduled for service.
In addition, keeping the bfq_queue scheduled for service, but with no
process reference any longer, may cause the bfq_queue to be freed when
descheduled from service. But this is assumed to never happen, and
causes a UAF if it happens. This, in turn, caused crashes [1, 2].
This commit fixes this issue by descheduling an empty bfq_queue when
it remains with not process reference.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1767539
[2] https://bugzilla.kernel.org/show_bug.cgi?id=205447
Fixes: 3726112ec731 ("block, bfq: re-schedule empty queues if they deserve I/O plugging")
Reported-by: Chris Evich <cevich@redhat.com>
Reported-by: Patrick Dung <patdung100@gmail.com>
Reported-by: Thorsten Schubert <tschubert@bafh.org>
Tested-by: Thorsten Schubert <tschubert@bafh.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The commit 60849562a5db ("ALSA: usb-audio: Fix possible NULL
dereference at create_yamaha_midi_quirk()") added NULL checks in
create_yamaha_midi_quirk(), but there was an overlook. The code
allows one of either injd or outjd is NULL, but the second if check
made returning -ENODEV if any of them is NULL. Fix it in a proper
form.
Fixes: 60849562a5db ("ALSA: usb-audio: Fix possible NULL dereference at create_yamaha_midi_quirk()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191113111259.24123-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-14
here another pull request for net/master consisting of one patch (including my S-o-b).
Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan
driver's error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.4
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is fixing memory leak reported by Syzkaller:
BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
hex dump (first 32 bytes):
73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
[<0000000083306e66>] kvmalloc_node+0x3a/0xc0
[<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
[<0000000061a996c9>] slcan_open+0x3ae/0x9a0
[<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
[<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
[<000000004de5a617>] tty_ioctl+0x48d/0x1590
[<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
[<0000000059068dbc>] ksys_ioctl+0x99/0xb0
[<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
[<0000000053d0332e>] do_syscall_64+0x16f/0x580
[<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<000000008ea75434>] 0xffffffffffffffff
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A test case was reported where two linked reads with registered buffers
failed the second link always. This is because we set the expected value
of a request in req->result, and if we don't get this result, then we
fail the dependent links. For some reason the registered buffer import
returned -ERROR/0, while the normal import returns -ERROR/length. This
broke linked commands with registered buffers.
Fix this by making io_import_fixed() correctly return the mapped length.
Cc: stable@vger.kernel.org # v5.3
Reported-by: 李通洲 <carter.li@eoitek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
"ret" is zero or possibly uninitialized on this error path. It
should be a negative error code instead.
Fixes: 2d0cb84dd973 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
