| Age | Commit message (Collapse) | Author |
|---|
|
Similarly to what PHYLIB already does, make sure that
PHY_INTERFACE_MODE_MOCA is reported as PORT_BNC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink_get_fixed_state() currently consults an optional "link_gpio"
GPIO descriptor, expand this mechanism to allow specifying a custom
callback. This is necessary to support out of band link notifcation
(e.g: from an interrupt within a MMIO register).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some subsystems like DSA may be trying to connect to a PHY through OF first,
and then attempt a connect using a local MDIO bus, remove the error message:
"unable to find PHY node" so we can let MAC drivers whether to print it or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may not always be able to resolve a correct phy_interface_t value before
actually connecting to the PHY device, when that happens, just have
phylink_connect_phy() utilize what the PHY device/driver provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to let subsystems like DSA fully utilize PHYLINK, we need to be able
to communicate phy_device::flags from of_phy_{connect,attach} even when using
PHYLINK APIs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, active Fast Open is paused on a specific
destination IP address if the previous connections to the
IP address have experienced recurring timeouts . But recent
experiments by Microsoft (https://goo.gl/cykmn7) and Mozilla
browsers indicate the isssue is often caused by broken middle-boxes
sitting close to the client. Therefore it is much better user
experience if Fast Open is disabled out-right globally to avoid
experiencing further timeouts on connections toward other
destinations.
This patch changes the destination-IP disablement to global
disablement if a connection experiencing recurring timeouts
or aborts due to timeout. Repeated incidents would still
exponentially increase the pause time, starting from an hour.
This is extremely conservative but an unfortunate compromise to
minimize bad experience due to broken middle-boxes.
Reported-by: Dragana Damjanovic <ddamjanovic@mozilla.com>
Reported-by: Patrick McManus <mcmanus@ducksong.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for ethtool get_module_info() and get_module_eeprom()
callbacks that will dump necessary information for a SFP.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_warn_bad_offload warns when packets enter the GSO stack that
require skb_checksum_help or vice versa. Do not warn on arbitrary
bad packets. Packet sockets can craft many. Syzkaller was able to
demonstrate another one with eth_type games.
In particular, suppress the warning when segmentation returns an
error, which is for reasons other than checksum offload.
See also commit 36c92474498a ("net: WARN if skb_checksum_help() is
called on skb requiring segmentation") for context on this warning.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 3a9b76fd0db9 ("tcp: allow drivers to tweak TSQ logic")
I gave a code sample to set sk->sk_pacing_shift that was not complete.
Better add a helper that can be used by drivers without worries,
and maybe amended in the future.
A wifi driver might use it from its ndo_start_xmit()
Following call would setup TCP to allow up to ~8ms of queued data per
flow.
sk_pacing_shift_update(skb->sk, 7);
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch the bridge used a fixed 256 element hash table which
was fine for small use cases (in my tests it starts to degrade
above 1000 entries), but it wasn't enough for medium or large
scale deployments. Modern setups have thousands of participants in a
single bridge, even only enabling vlans and adding a few thousand vlan
entries will cause a few thousand fdbs to be automatically inserted per
participating port. So we need to scale the fdb table considerably to
cope with modern workloads, and this patch converts it to use a
rhashtable for its operations thus improving the bridge scalability.
Tests show the following results (10 runs each), at up to 1000 entries
rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it
is 2 times faster and at 30000 it is 50 times faster.
Obviously this happens because of the properties of the two constructs
and is expected, rhashtable keeps pretty much a constant time even with
10000000 entries (tested), while the fixed hash table struggles
considerably even above 10000.
As a side effect this also reduces the net_bridge struct size from 3248
bytes to 1344 bytes. Also note that the key struct is 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function meson_gxl_read_status is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'meson_gxl_read_status' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove XGMII as an option for the 88x3310 PHY driver, as the PHY doesn't
support XGMII's 32-bit data lanes. It supports USXGMII, which is not
XGMII, but a single-lane serdes interface - see
https://developer.cisco.com/site/usgmii-usxgmii/
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.
The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit. This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.
Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock. This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use XAUI rather than XGMII for DSA link ports, as this is the interface
mode that the switches actually use. XAUI is the 4 lane bus with clock
per direction, whereas XGMII is a 32 bit bus with clock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XGMII is a 32-bit bus plus two clock signals per direction. XAUI is
four serial lanes per direction. The 88e6190 supports XAUI but not
XGMII as it doesn't have enough pins. The same is true of 88e6176.
Match on PHY_INTERFACE_MODE_XAUI for the XAUI port type, but keep
accepting XGMII for backwards compatibility.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver may sleep under a spinlock.
The function call path is:
rr_close (acquire the spinlock)
free_irq --> may sleep
To fix it, free_irq is moved to the place without holding the spinlock.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
r8169: extend PCI core and switch to device-managed functions in probe
Probe error path and remove callback can be significantly simplified
by using device-managed functions. To be able to do this in the r8169
driver we need a device-managed version of pci_set_mwi first.
v2:
Change patch 1 based on Björn's review comments and add his Acked-by.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_napi_del is called implicitely by free_netdev, therefore we
don't have to do it explicitely.
When the probe error path is reached, the net_device isn't
registered yet. Therefore reordering the call to netif_napi_del
shouldn't cause any issues.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify probe error path and remove callback by using device-managed
functions.
rtl_disable_msi isn't needed any longer because the release callback
of pcim_enable_device does this implicitely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add pcim_set_mwi(), a device-managed version of pci_set_mwi().
First user is the Realtek r8169 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First, rename __inet_twsk_hashdance() to inet_twsk_hashdance()
Then, remove one inet_twsk_put() by setting tw_refcnt to 3 instead
of 4, but adding a fat warning that we do not have the right to access
tw anymore after inet_twsk_hashdance()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The follow patchset contains Netfilter fixes for your net tree,
they are:
1) Fix compilation warning in x_tables with clang due to useless
redundant reassignment, from Colin Ian King.
2) Add bugtrap to net_exit to catch uninitialized lists, patch
from Vasily Averin.
3) Fix out of bounds memory reads in H323 conntrack helper, this
comes with an initial patch to remove replace the obscure
CHECK_BOUND macro as a dependency. From Eric Sesterhenn.
4) Reduce retransmission timeout when window is 0 in TCP conntrack,
from Florian Westphal.
6) ctnetlink clamp timeout to INT_MAX if timeout is too large,
otherwise timeout wraps around and it results in killing the
entry that is being added immediately.
7) Missing CAP_NET_ADMIN checks in cthelper and xt_osf, due to
no netns support. From Kevin Cernekee.
8) Missing maximum number of instructions checks in xt_bpf, patch
from Jann Horn.
9) With no CONFIG_PROC_FS ipt_CLUSTERIP compilation breaks,
patch from Arnd Bergmann.
10) Missing netlink attribute policy in nftables exthdr, from
Florian Westphal.
11) Enable conntrack with IPv6 MASQUERADE rules, as a357b3f80bc8
should have done in first place, from Konstantin Khlebnikov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subash Abhinov Kasiviswanathan says:
====================
net: qualcomm: rmnet: Configuration options
This series adds support for configuring features on rmnet devices.
The rmnet specific features to be configured here are aggregation and
control commands.
Patch 1 is a cleanup of return codes in the transmit path.
Patch 2 removes some redundant ingress and egress macros.
Patch 3 restricts the creation of rmnet dev to one dev per mux id for a
given real dev.
Patch 4 adds ethernet data path support.
Patches 5-6 add support for configuring features on new and existing
rmnet devices.
v1->v2:
The memory leak fixed as part of patch 1 is merged seperately as
a896d94abd2c ("net: qualcomm: rmnet: Fix leak on transmit failure").
Fix a use after free in patch 4 if a packet with headroom lesser than ethernet
header length is received.
v2->v3:
Fix formatting problem in patch 5 in the return statement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an option to configure the mux id, aggregation and commad feature
for existing rmnet devices. Implement the changelink netlink
operation for this.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an option to configure the rmnet aggregation and command features
on device creation. This is achieved by using the vlan flags option.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to send and receive packets over ethernet.
An example of usage is testing the data path on UML. This can be
achieved by setting up two UML instances in multicast mode and
associating rmnet over the UML ethernet device.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon de-multiplexing data from one real dev, the packets can be sent
to an unique rmnet device for a given mux id.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multiplexing is always enabled when transmiting from a rmnet device,
so remove the redundant egress macros. De-multiplexing is always
enabled when receiving packets from a rmnet device, so remove those
ingress macros.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the success and consumed entries were actually in use.
Use standard error codes instead.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables tail loss probe in cwnd reduction (CWR) state
to detect potential losses. Prior to this patch, since the sender
uses PRR to determine the cwnd in CWR state, the combination of
CWR+PRR plus tcp_tso_should_defer() could cause unnecessary stalls
upon losses: PRR makes cwnd so gentle that tcp_tso_should_defer()
defers sending wait for more ACKs. The ACKs may not come due to
packet losses.
Disallowing TLP when there is unused cwnd had the primary effect
of disallowing TLP when there is TSO deferral, Nagle deferral,
or we hit the rwin limit. Because basically every application
write() or incoming ACK will cause us to run tcp_write_xmit()
to see if we can send more, and then if we sent something we call
tcp_schedule_loss_probe() to see if we should schedule a TLP. At
that point, there are a few common reasons why some cwnd budget
could still be unused:
(a) rwin limit
(b) nagle check
(c) TSO deferral
(d) TSQ
For (d), after the next packet tx completion the TSQ mechanism
will allow us to send more packets, so we don't really need a
TLP (in practice it shouldn't matter whether we schedule one
or not). But for (a), (b), (c) the sender won't send any more
packets until it gets another ACK. But if the whole flight was
lost, or all the ACKs were lost, then we won't get any more ACKs,
and ideally we should schedule and send a TLP to get more feedback.
In particular for a long time we have wanted some kind of timer for
TSO deferral, and at least this would give us some kind of timer
Reported-by: Steve Ibanez <sibanez@stanford.edu>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Nandita Dukkipati <nanditad@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in tc_action_net_exit(), it is good to
batch them to speedup tc action dismantle.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Changes since v2 [1]:
* Merged with latest code changes
Changes since v1:
Update made thanks to David's review, much appreciated David.
* Improved inconsistent failure handling of clock rate setting
* For completeness of usecase, added arc_emac_probe error handling
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Closing a multicast socket after the final IPv4 address is deleted
from an interface can generate a membership report that uses the
source IP from a different interface. The following test script, run
from an isolated netns, reproduces the issue:
#!/bin/bash
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 up
ip link set dummy1 up
ip addr add 10.1.1.1/24 dev dummy0
ip addr add 192.168.99.99/24 dev dummy1
tcpdump -U -i dummy0 &
socat EXEC:"sleep 2" \
UDP4-DATAGRAM:239.101.1.68:8889,ip-add-membership=239.0.1.68:10.1.1.1 &
sleep 1
ip addr del 10.1.1.1/24 dev dummy0
sleep 5
kill %tcpdump
RFC 3376 specifies that the report must be sent with a valid IP source
address from the destination subnet, or from address 0.0.0.0. Add an
extra check to make sure this is the case.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function tipc_sk_mcast_rcv() we call refcount_dec(&skb->users)
on received sk_buffers. Since the reference counter might hit zero at
this point, we have a potential memory leak.
We fix this by replacing refcount_dec() with kfree_skb().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stephen Hemminger says:
====================
hv_netvsc: Fix default and limit of recv buffer
The default for receive buffer descriptors is not correct, it should
match the default receive buffer size and the upper limit of receive
buffer size is too low. Also, for older versions of Window servers
hosts, different lower limit check is necessary, otherwise the buffer
request will be rejected by the host, resulting vNIC not come up.
This patch set corrects these problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The values were not computed correctly. There are no significant
visible impact, though.
The intended size of RX buffer is 16 MB, and the default slot size is 1728.
So, NETVSC_DEFAULT_RX should be 16*1024*1024 / 1728 = 9709.
The intended size of TX buffer is 1 MB, and the slot size is 6144.
So, NETVSC_DEFAULT_TX should be 1024*1024 / 6144 = 170.
The patch puts the formula directly into the macro, and moves them to
hyperv_net.h, together with related macros.
Fixes: 5023a6db73196 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The max should be 31 MB on host with NVSP version > 2.
On legacy hosts (NVSP version <=2) only 15 MB receive buffer is allowed,
otherwise the buffer request will be rejected by the host, resulting
vNIC not coming up.
The NVSP version is only available after negotiation. So, we add the
limit checking for legacy hosts in netvsc_init_buf().
Fixes: 5023a6db73196 ("netvsc: increase default receive buffer size")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in igmp code where it is
assumed the mtu is suitable.
Fix this by reading device mtu once and checking IPv4 minimal MTU.
This patch adds missing IPV4_MIN_MTU define, to not abuse
ETH_MIN_MTU anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller reported crashes in IPv6 stack [1]
Xin Long found that lo MTU was set to silly values.
IPv6 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in mld code where it is assumed
the mtu is suitable.
Fix this by reading device mtu once and checking IPv6 minimal MTU.
[1]
skbuff: skb_over_panic: text:0000000010b86b8d len:196 put:20
head:000000003b477e60 data:000000000e85441e tail:0xd4 end:0xc0 dev:lo
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.15.0-rc2-mm1+ #39
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x15c/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801db307508 EFLAGS: 00010286
RAX: 0000000000000082 RBX: ffff8801c517e840 RCX: 0000000000000000
RDX: 0000000000000082 RSI: 1ffff1003b660e61 RDI: ffffed003b660e95
RBP: ffff8801db307570 R08: 1ffff1003b660e23 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff85bd4020
R13: ffffffff84754ed2 R14: 0000000000000014 R15: ffff8801c4e26540
FS: 0000000000000000(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000463610 CR3: 00000001c6698000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
skb_over_panic net/core/skbuff.c:109 [inline]
skb_put+0x181/0x1c0 net/core/skbuff.c:1694
add_grhead.isra.24+0x42/0x3b0 net/ipv6/mcast.c:1695
add_grec+0xa55/0x1060 net/ipv6/mcast.c:1817
mld_send_cr net/ipv6/mcast.c:1903 [inline]
mld_ifc_timer_expire+0x4d2/0x770 net/ipv6/mcast.c:2448
call_timer_fn+0x23b/0x840 kernel/time/timer.c:1320
expire_timers kernel/time/timer.c:1357 [inline]
__run_timers+0x7e1/0xb60 kernel/time/timer.c:1660
run_timer_softirq+0x4c/0xb0 kernel/time/timer.c:1686
__do_softirq+0x29d/0xbb2 kernel/softirq.c:285
invoke_softirq kernel/softirq.c:365 [inline]
irq_exit+0x1d3/0x210 kernel/softirq.c:405
exiting_irq arch/x86/include/asm/apic.h:540 [inline]
smp_apic_timer_interrupt+0x16b/0x700 arch/x86/kernel/apic/apic.c:1052
apic_timer_interrupt+0xa9/0xb0 arch/x86/entry/entry_64.S:920
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
memalloc_noio_save modifies the behavior of MM, we must restore it after
we are done.
Fixes: d83187dda9b9 ("IB/IPoIB: Convert IPoIB to memalloc_noio_* calls")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Richard Leitner says:
====================
net: fec: fix refclk enable for SMSC LAN8710/20
This patch series fixes the use of the SMSC LAN8710/20 with a Freescale ETH
when the refclk is generated by the FSL.
This patchset depends on the "phylib: Add device reset GPIO support" patch
submitted by Geert Uytterhoeven/Sergei Shtylyov, which was merged to
net-next as commit bafbdd527d56 ("phylib: Add device reset GPIO support").
Changes v5:
- fix reset delay calculation (max_t instead of min_t)
Changes v4:
- simplify dts parsing
- simplify reset delay evaluation and execution
- fec: ensure to only reset once during fec_enet_open()
- remove dependency notes from commit message
- add reviews and acks
Changes v3:
- use phylib to hard-reset the PHY
- implement reset delays in phylib
- add new phylib API & flag (PHY_RST_AFTER_CLK_EN) to determine if
a PHY is affected
Changes v2:
- simplify and fix fec_reset_phy function to support multiple calls
- include: linux: phy: harmonize phy_id{,_mask} type
- reset the phy instead of not turning the clock on and off
(which would have caused a power consumption regression)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
the refclk on and off again during operation (according to their
datasheet). Nonetheless exactly this behaviour was introduced for power
saving reasons by commit e8fcfcd5684a ("net: fec: optimize the clock management to save power").
Therefore add support for the phy_reset_after_clk_enable function from
phylib to mitigate this issue.
Generally speaking this issue is only relevant if the ref clk for the
PHY is generated by the SoC and therefore the PHY is configured to
"REF_CLK In Mode". In our specific case (PCB) this problem does occur at
about every 10th to 50th POR of an LAN8710 connected to an i.MX6SOLO
SoC. The typical symptom of this problem is a "swinging" ethernet link.
Similar issues were reported by users of the NXP forum:
https://community.nxp.com/thread/389902
https://community.nxp.com/message/309354
With this patch applied the issue didn't occur for at least a few
hundret PORs of our board.
Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Microchip/SMSC LAN8710/LAN8720 PHYs need (according to their
datasheet [1]) a continuous REF_CLK when configured to "REF_CLK In Mode".
Therefore set the PHY_RST_AFTER_CLK_EN flag for those PHYs to let the
ETH driver reset them after the REF_CLK is enabled.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00002165B.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
