| Age | Commit message (Collapse) | Author |
|---|
|
into drm-fixes
- Powerplay fixes for cards with no displays attached
- Couple of DC fixes
- radeon workaround for PPC64
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: insist on 32-bit DMA for Cedar on PPC64/PPC64LE
drm/amd/display: VGA black screen from s3 when attached to hook
drm/amdgpu: Unify the dm resume calls into one
drm/amdgpu: Add a missing lock for drm_mm_takedown
Revert "drm/radeon/pm: autoswitch power state when in balanced mode"
drm/amd/powerplay/smu7: allow mclk switching with no displays
drm/amd/powerplay/vega10: allow mclk switching with no displays
|
|
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1c2 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull seccomp fix from James Morris:
"This disables the seccomp samples when cross compiling.
We've seen too many build issues here, so it's best to just disable
it, especially since they're just the samples"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
samples/seccomp: do not compile when cross compiled
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into fixes-v4.16-rc4
- do not build samples when cross compiling (Michal Hocko)
From Kees: "This disables the seccomp samples when cross compiling. We're seen too many build issues here, so
it's best to just disable it, especially since they're just the samples."
|
|
Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[ 440.012034] kernel BUG at block/blk-ioc.c:146!
[ 440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[ 440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[ 440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[ 440.028615] RIP: 0010:put_io_context+0x8b/0x90
[ 440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[ 440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[ 440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[ 440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[ 440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[ 440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[ 440.035239] FS: 0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[ 440.060190] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[ 440.110498] Call Trace:
[ 440.135443] bio_disassociate_task+0x1b/0x60
[ 440.160355] bio_free+0x1b/0x60
[ 440.184666] bio_put+0x23/0x30
[ 440.208272] search_free+0x23/0x40 [bcache]
[ 440.231448] cached_dev_write_complete+0x31/0x70 [bcache]
[ 440.254468] closure_put+0xb6/0xd0 [bcache]
[ 440.277087] request_endio+0x30/0x40 [bcache]
[ 440.298703] bio_endio+0xa1/0x120
[ 440.319644] handle_stripe+0x418/0x2270 [raid456]
[ 440.340614] ? load_balance+0x17b/0x9c0
[ 440.360506] handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[ 440.380675] ? __release_stripe+0x15/0x20 [raid456]
[ 440.400132] raid5d+0x3ed/0x5d0 [raid456]
[ 440.419193] ? schedule+0x36/0x80
[ 440.437932] ? schedule_timeout+0x1d2/0x2f0
[ 440.456136] md_thread+0x122/0x150
[ 440.473687] ? wait_woken+0x80/0x80
[ 440.491411] kthread+0x102/0x140
[ 440.508636] ? find_pers+0x70/0x70
[ 440.524927] ? kthread_associate_blkcg+0xa0/0xa0
[ 440.541791] ret_from_fork+0x35/0x40
[ 440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[ 440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[ 440.628575] ---[ end trace a1fd79d85643a73e ]--
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 2831231d4c3f ("bcache: reduce cache_set devices iteration by
devices_max_used") adds c->devices_max_used to reduce iteration of
c->uuids elements, this value is updated in bcache_device_attach().
But for flash only volume, when calling flash_devs_run(), the function
bcache_device_attach() is not called yet and c->devices_max_used is not
updated. The unexpected result is, the flash only volume won't be run
by flash_devs_run().
This patch fixes the issue by iterate all c->uuids elements in
flash_devs_run(). c->devices_max_used will be updated properly when
bcache_device_attach() gets called.
[mlyle: commit subject edited for character limit]
Fixes: 2831231d4c3f ("bcache: reduce cache_set devices iteration by devices_max_used")
Reported-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"Bugfixes for TPM, from Jeremy Boone, via Jarkko Sakkinen"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix potential buffer overruns caused by bit glitches on the bus
tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
tpm_tis: fix potential buffer overruns caused by bit glitches on the bus
|
|
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e990 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b02eee7e ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
wake_klogd is a local variable in console_unlock(). The information
is lost when the console_lock owner using the busy wait added by
the commit dbdda842fe96f8932 ("printk: Add console owner and waiter
logic to load balance console writes"). The following race is
possible:
CPU0 CPU1
console_unlock()
for (;;)
/* calling console for last message */
printk()
log_store()
log_next_seq++;
/* see new message */
if (seen_seq != log_next_seq) {
wake_klogd = true;
seen_seq = log_next_seq;
}
console_lock_spinning_enable();
if (console_trylock_spinning())
/* spinning */
if (console_lock_spinning_disable_and_check()) {
printk_safe_exit_irqrestore(flags);
return;
console_unlock()
if (seen_seq != log_next_seq) {
/* already seen */
/* nothing to do */
Result: Nobody would wakeup klogd.
One solution would be to make a global variable from wake_klogd.
But then we would need to manipulate it under a lock or so.
This patch wakes klogd also when console_lock is passed to the
spinning waiter. It looks like the right way to go. Also userspace
should have a chance to see and store any "flood" of messages.
Note that the very late klogd wake up was a historic solution.
It made sense on single CPU systems or when sys_syslog() operations
were synchronized using the big kernel lock like in v2.1.113.
But it is questionable these days.
Fixes: dbdda842fe96f8932 ("printk: Add console owner and waiter logic to load balance console writes")
Link: http://lkml.kernel.org/r/20180226155734.dzwg3aovqnwtvkoy@pathway.suse.cz
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_get_named_gpiod_flags() used directly in of_find_gpio() or indirectly
through of_find_spi_gpio() or of_find_regulator_gpio() can return
-EPROBE_DEFER. This gets overwritten by the subsequent of_find_*_gpio()
calls.
This patch fixes this by trying of_find_spi_gpio() or
of_find_regulator_gpio() only if deferred probing was not requested by
the previous of_get_named_gpiod_flags() call.
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[Augmented to fit with Maxime's patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commits c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
and 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO
properties") have introduced a regression in the way error codes from
of_get_named_gpiod_flags are handled.
Previously, those errors codes were returned immediately, but the two
commits mentioned above are now overwriting the error pointer, meaning that
whatever value has been returned will be dropped in favor of whatever the
two new functions will return.
This might not be a big deal except for EPROBE_DEFER, on which GPIOlib
customers will depend on, and that will now be returned as an hard error
which means that they will not probe anymore, instead of gently deferring
their probe.
Since EPROBE_DEFER basically means that we have found a valid property but
there was no GPIO controller registered to handle it, fix this issues by
returning it as soon as we encounter it.
Fixes: c85823390215 ("gpio: of: Support SPI nonstandard GPIO properties")
Fixes: 6a537d48461d ("gpio: of: Support regulator nonstandard GPIO properties")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[Fold in fix to the fix]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
|
|
Update .gitignore with new test.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Silence the following command being printed while running test.
./mem-on-off-test.sh -r 2 && echo "selftests: memory-hotplug [PASS]" ||
echo "selftests: memory-hotplug [FAIL]"
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.
$ make
make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: *** [all] Error 1
make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
make: *** [all] Error 2
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Commit 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
removed the SCPI cpufreq dependency on arm_big_little cpufreq driver.
However the Kconfig entry still depends on ARM_BIG_LITTLE_CPUFREQ
which is clearly wrong.
This patch removes that unnecessary Kconfig dependency.
Fixes: 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
Reported-by: Quentin Perret <quentin.perret@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
changed the cpufreq driver on juno from arm_big_little to scpi.
The scpi set_target function does not call the frequency-invariance
setter function arch_set_freq_scale() like the arm_big_little set_target
function does. As a result the task scheduler load and utilization
signals are not frequency-invariant on this platform anymore.
Fix this by adding a call to arch_set_freq_scale() into
scpi_cpufreq_set_target().
Fixes: 343a8d17fa8d (cpufreq: scpi: remove arm_big_little dependency)
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull idr fixes from Matthew Wilcox:
"One test-suite build fix for you and one run-time regression fix.
The regression fix includes new tests to make sure they don't pop back
up."
* 'idr-2018-02-06' of git://git.infradead.org/users/willy/linux-dax:
idr: Fix handling of IDs above INT_MAX
radix tree test suite: Fix build
|
|
It is entirely possible that the BIOS wasn't able to assign resources to a
device. In this case don't crash in pci_release_resource() when we try to
resize the resource.
Fixes: 8bb705e3e79d ("PCI: Add pci_resize_resource() for resizing BARs")
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
CC: stable@vger.kernel.org # v4.15+
|
|
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db75 ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The CONFIG_LIRC symbol has changed from 'tristate' to 'bool, so we now
get a warning for omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:322:warning: symbol value 'm' invalid for LIRC
This changes the file to mark the symbol as built-in to get rid of the
warning.
Fixes: a60d64b15c20 ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Gerd reports that ->i_mode may contain other bits besides S_IFCHR. Use
S_ISCHR() instead. Otherwise, get_user_pages_longterm() may fail on
device-dax instances when those are meant to be explicitly allowed.
Fixes: 2bb6d2837083 ("mm: introduce get_user_pages_longterm")
Cc: <stable@vger.kernel.org>
Reported-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Jane Chu <jane.chu@oracle.com>
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In Patch:
[7a862fb] brd: remove dax support
Dan Williams has removed the only might_sleep
implementation of ->direct_access.
So we no longer need to check for it.
CC: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Boaz Harrosh <boazh@netapp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Khalid reported that the kernel selftests are currently failing:
selftests: test_bpf.sh
========================================
test_bpf: [FAIL]
not ok 1..8 selftests: test_bpf.sh [FAIL]
He bisected it to 6ce711f2750031d12cec91384ac5cfa0a485b60a ("idr: Make
1-based IDRs more efficient").
The root cause is doing a signed comparison in idr_alloc_u32() instead
of an unsigned comparison. I went looking for any similar problems and
found a couple (which would each result in the failure to warn in two
situations that aren't supposed to happen).
I knocked up a few test-cases to prove that I was right and added them
to the test-suite.
Reported-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
|
|
'struct blk_user_trace_setup' is passed to BLKTRACESETUP, not
BLKTRACESTART.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"sb_edac: Prevent memory corruption on KNL (from Anna Karbownik)"
* tag 'edac_fixes_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Fix out of bound writes during DIMM configuration on KNL
|
|
When specifying string type mount option (e.g., logdev)
several times in a mount, current option parsing may
cause memory leak. Hence, call kfree for previous one
in this case.
Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Yet another pile of melted spectrum related changes:
- sanitize the array_index_nospec protection mechanism: Remove the
overengineered array_index_nospec_mask_check() magic and allow
const-qualified types as index to avoid temporary storage in a
non-const local variable.
- make the microcode loader more robust by properly propagating error
codes. Provide information about new feature bits after micro code
was updated so administrators can act upon.
- optimizations of the entry ASM code which reduce code footprint and
make the code simpler and faster.
- fix the {pmd,pud}_{set,clear}_flags() implementations to work
properly on paravirt kernels by removing the address translation
operations.
- revert the harmful vmexit_fill_RSB() optimization
- use IBRS around firmware calls
- teach objtool about retpolines and add annotations for indirect
jumps and calls.
- explicitly disable jumplabel patching in __init code and handle
patching failures properly instead of silently ignoring them.
- remove indirect paravirt calls for writing the speculation control
MSR as these calls are obviously proving the same attack vector
which is tried to be mitigated.
- a few small fixes which address build issues with recent compiler
and assembler versions"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
KVM/VMX: Optimize vmx_vcpu_run() and svm_vcpu_run() by marking the RDMSR path as unlikely()
KVM/x86: Remove indirect MSR op calls from SPEC_CTRL
objtool, retpolines: Integrate objtool with retpoline support more closely
x86/entry/64: Simplify ENCODE_FRAME_POINTER
extable: Make init_kernel_text() global
jump_label: Warn on failed jump_label patching attempt
jump_label: Explicitly disable jump labels in __init code
x86/entry/64: Open-code switch_to_thread_stack()
x86/entry/64: Move ASM_CLAC to interrupt_entry()
x86/entry/64: Remove 'interrupt' macro
x86/entry/64: Move the switch_to_thread_stack() call to interrupt_entry()
x86/entry/64: Move ENTER_IRQ_STACK from interrupt macro to interrupt_entry
x86/entry/64: Move PUSH_AND_CLEAR_REGS from interrupt macro to helper function
x86/speculation: Move firmware_restrict_branch_speculation_*() from C to CPP
objtool: Add module specific retpoline rules
objtool: Add retpoline validation
objtool: Use existing global variables for options
x86/mm/sme, objtool: Annotate indirect call in sme_encrypt_execute()
x86/boot, objtool: Annotate indirect jump in secondary_startup_64()
x86/paravirt, objtool: Annotate indirect calls
...
|
|
Pull KVM fixes from Paolo Bonzini:
"s390:
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (40 commits)
KVM: SVM: Fix SEV LAUNCH_SECRET command
KVM: SVM: install RSM intercept
KVM: SVM: no need to call access_ok() in LAUNCH_MEASURE command
include: psp-sev: Capitalize invalid length enum
crypto: ccp: Fix sparse, use plain integer as NULL pointer
KVM: X86: Avoid traversing all the cpus for pv tlb flush when steal time is disabled
x86/kvm: Make parse_no_xxx __init for kvm
KVM: x86: fix backward migration with async_PF
kvm: fix warning for non-x86 builds
kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds
tools/kvm_stat: print 'Total' line for multiple events only
tools/kvm_stat: group child events indented after parent
tools/kvm_stat: separate drilldown and fields filtering
tools/kvm_stat: eliminate extra guest/pid selection dialog
tools/kvm_stat: mark private methods as such
tools/kvm_stat: fix debugfs handling
tools/kvm_stat: print error on invalid regex
tools/kvm_stat: fix crash when filtering out all non-child trace events
tools/kvm_stat: avoid 'is' for equality checks
tools/kvm_stat: use a more pythonic way to iterate over dictionaries
...
|
|
When blkdev_open() races with device removal and creation it can happen
that unhashed bdev inode gets associated with newly created gendisk
like:
CPU0 CPU1
blkdev_open()
bdev = bd_acquire()
del_gendisk()
bdev_unhash_inode(bdev);
remove device
create new device with the same number
__blkdev_get()
disk = get_gendisk()
- gets reference to gendisk of the new device
Now another blkdev_open() will not find original 'bdev' as it got
unhashed, create a new one and associate it with the same 'disk' at
which point problems start as we have two independent page caches for
one device.
Fix the problem by verifying that the bdev inode didn't get unhashed
before we acquired gendisk reference. That way we make sure gendisk can
get associated only with visible bdev inodes.
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When two blkdev_open() calls for a partition race with device removal
and recreation, we can hit BUG_ON(!bd_may_claim(bdev, whole, holder)) in
blkdev_open(). The race can happen as follows:
CPU0 CPU1 CPU2
del_gendisk()
bdev_unhash_inode(part1);
blkdev_open(part1, O_EXCL) blkdev_open(part1, O_EXCL)
bdev = bd_acquire() bdev = bd_acquire()
blkdev_get(bdev)
bd_start_claiming(bdev)
- finds old inode 'whole'
bd_prepare_to_claim() -> 0
bdev_unhash_inode(whole);
<device removed>
<new device under same
number created>
blkdev_get(bdev);
bd_start_claiming(bdev)
- finds new inode 'whole'
bd_prepare_to_claim()
- this also succeeds as we have
different 'whole' here...
- bad things happen now as we
have two exclusive openers of
the same bdev
The problem here is that block device opens can see various intermediate
states while gendisk is shutting down and then being recreated.
We fix the problem by introducing new lookup_sem in gendisk that
synchronizes gendisk deletion with get_gendisk() and furthermore by
making sure that get_gendisk() does not return gendisk that is being (or
has been) deleted. This makes sure that once we ever manage to look up
newly created bdev inode, we are also guaranteed that following
get_gendisk() will either return failure (and we fail open) or it
returns gendisk for the new device and following bdget_disk() will
return new bdev inode (i.e., blkdev_open() follows the path as if it is
completely run after new device is created).
Reported-and-analyzed-by: Hou Tao <houtao1@huawei.com>
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When two blkdev_open() calls race with device removal and recreation,
__blkdev_get() can use looked up gendisk after it is freed:
CPU0 CPU1 CPU2
del_gendisk(disk);
bdev_unhash_inode(inode);
blkdev_open() blkdev_open()
bdev = bd_acquire(inode);
- creates and returns new inode
bdev = bd_acquire(inode);
- returns the same inode
__blkdev_get(devt) __blkdev_get(devt)
disk = get_gendisk(devt);
- got structure of device going away
<finish device removal>
<new device gets
created under the same
device number>
disk = get_gendisk(devt);
- got new device structure
if (!bdev->bd_openers) {
does the first open
}
if (!bdev->bd_openers)
- false
} else {
put_disk_and_module(disk)
- remember this was old device - this was last ref and disk is
now freed
}
disk_unblock_events(disk); -> oops
Fix the problem by making sure we drop reference to disk in
__blkdev_get() only after we are really done with it.
Reported-by: Hou Tao <houtao1@huawei.com>
Tested-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a proper counterpart to get_disk_and_module() -
put_disk_and_module(). Currently it is opencoded in several places.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rename get_disk() to get_disk_and_module() to make sure what the
function does. It's not a great name but at least it is now clear that
put_disk() is not it's counterpart.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 8ddcd653257c "block: introduce GENHD_FL_HIDDEN" added handling of
hidden devices to get_gendisk() but forgot to drop module reference
which is also acquired by get_disk(). Drop the reference as necessary.
Arguably the function naming here is misleading as put_disk() is *not*
the counterpart of get_disk() but let's fix that in the follow up
commit since that will be more intrusive.
Fixes: 8ddcd653257c18a669fcb75ee42c37054908e0d6
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Introduce __smp_{mb,rmb,wmb}, and rely on the generic definitions
for smp_{mb,rmb,wmb}. A first consequence is that smp_{mb,rmb,wmb}
map to a compiler barrier on !SMP (while their definition remains
unchanged on SMP). As a further consequence, smp_load_acquire and
smp_store_release have "fence rw,rw" instead of "fence iorw,iorw".
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
