| Age | Commit message (Collapse) | Author |
|---|
|
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Ulf writes:
"MMC core:
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card"
* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
libertas: call into generic suspend code before turning off power
mmc: block: avoid multiblock reads for the last sector in SPI mode
|
|
Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
Signed-off-by: Ankita Bajaj <bankita@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Linus writes:
"GPIO fix for the v4.19 series:
- Fix up the interrupt parent for the irqdomains."
* tag 'gpio-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Assign gpio_irq_chip::parents to non-stack pointer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Linus writes:
"pin control fix for v4.19:
A single pin control fix for v4.19:
- Interrupt setup in the MCP23S08 driver."
* tag 'pinctrl-v4.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mcp23s08: fix irq and irqchip setup order
|
|
Boris writes:
"mdt: fix for 4.19-rc8
* Fix a stack overflow in lib/bch.c"
* tag 'mtd/fixes-for-4.19-rc8' of git://git.infradead.org/linux-mtd:
lib/bch: fix possible stack overrun
|
|
Dave writes:
"drm fixes for 4.19-rc8
single nouveau runtime reference and mst change"
* tag 'drm-fixes-2018-10-12-1' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/drm/nouveau: Grab runtime PM ref in nv50_mstc_detect()
|
|
Doug writes:
"RDMA fixes:
Final for-rc pull request for 4.19
We only have one bug to submit this time around. It fixes a DMA
unmap issue where we unmapped the DMA address from the IOMMU before
we did from the card, resulting in a DMAR error with IOMMU enabled,
or possible crash without."
* tag 'for-gkh' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Unmap DMA addr from HCA before IOMMU
|
|
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Dmitry writes:
"Input updates for v4.19-rc7
- we added a few scheduling points into various input interfaces to
ensure that large writes will not cause RCU stalls
- fixed configuring PS/2 keyboards as wakeup devices on newer
platforms
- added a new Xbox gamepad ID."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - add a schedule point in uinput_inject_events()
Input: evdev - add a schedule point in evdev_write()
Input: mousedev - add a schedule point in mousedev_write()
Input: i8042 - enable keyboard wakeups by default when s2idle is used
Input: xpad - add support for Xbox1 PDP Camo series gamepad
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes
Stephen writes:
"A couple of warning fixes:
Two fixes from Peter Oberparleiter <oberpar@linux.ibm.com>:
Commit 6b7dca401cb1 ("tracing: Allow gcov profiling on only ftrace subsystem")
uncovered linker problems when using gcov kernel profiling on some
architectures. These problems were likely introduced earlier, and are
possibly related to compiler changes."
* tag 'next-fixes-20181012' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
vmlinux.lds.h: Fix linker warnings about orphan .LPBX sections
vmlinux.lds.h: Fix incomplete .text.exit discards
|
|
The previous patch introduced very large kernel stack usage and a Makefile
change to hide the warning about it.
From what I can tell, a number of things went wrong here:
- The BCH_MAX_T constant was set to the maximum value for 'n',
not the maximum for 't', which is much smaller.
- The stack usage is actually larger than the entire kernel stack
on some architectures that can use 4KB stacks (m68k, sh, c6x), which
leads to an immediate overrun.
- The justification in the patch description claimed that nothing
changed, however that is not the case even without the two points above:
the configuration is machine specific, and most boards never use the
maximum BCH_ECC_WORDS() length but instead have something much smaller.
That maximum would only apply to machines that use both the maximum
block size and the maximum ECC strength.
The largest value for 't' that I could find is '32', which in turn leads
to a 60 byte array instead of 2048 bytes. Making it '64' for future
extension seems also worthwhile, with 120 bytes for the array. Anything
larger won't fit into the OOB area on NAND flash.
With that changed, the warning can be enabled again.
Only linux-4.19+ contains the breakage, so this is only needed
as a stable backport if it does not make it into the release.
Fixes: 02361bc77888 ("lib/bch: Remove VLA usage")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
|
|
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple of fixes
Here are two fixes for the bcm_sf2 driver that were found during
testing unbind and analysing another issue during system
suspend/resume.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling both CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y and
CONFIG_GCOV_PROFILE_ALL=y results in linker warnings:
warning: orphan section `.data..LPBX1' being placed in
section `.data..LPBX1'.
LD_DEAD_CODE_DATA_ELIMINATION adds compiler flag -fdata-sections. This
option causes GCC to create separate data sections for data objects,
including those generated by GCC internally for gcov profiling. The
names of these objects start with a dot (.LPBX0, .LPBX1), resulting in
section names starting with 'data..'.
As section names starting with 'data..' are used for specific purposes
in the Linux kernel, the linker script does not automatically include
them in the output data section, resulting in the "orphan section"
linker warnings.
Fix this by specifically including sections named "data..LPBX*" in the
data section.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Enabling CONFIG_GCOV_PROFILE_ALL=y causes linker errors on ARM:
`.text.exit' referenced in section `.ARM.exidx.text.exit':
defined in discarded section `.text.exit'
`.text.exit' referenced in section `.fini_array.00100':
defined in discarded section `.text.exit'
And related errors on NDS32:
`.text.exit' referenced in section `.dtors.65435':
defined in discarded section `.text.exit'
The gcov compiler flags cause certain compiler versions to generate
additional destructor-related sections that are not yet handled by the
linker script, resulting in references between discarded and
non-discarded sections.
Since destructors are not used in the Linux kernel, fix this by
discarding these additional sections.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Greentime Hu <green.hu@gmail.com>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Replace the repeated license text with SDPX identifiers.
While at it bump the Copyright dates for files we touched
this year.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Nic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.
Remove sfp_mutex, it has no purpose.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported that since
commit 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tasklet initialisation would be better done by tasklet_init()
instead of assuming all the fields are in an ok state by default.
This does not fix any actual know bug.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 63ae7949e94a ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During boot, mlx4_core sets the driverinit configuration parameters and
updates the devlink module on the initial values calling
devlink_param_driverinit_value_set().
If devlink_param_driverinit_value_set() returns an error mlx4_core
reports kernel module warning.
This caused false alarm during boot in case kernel was compiled with
CONFIG_NET_DEVLINK off.
Fix by removing warning reported in case
devlink_param_driverinit_value_set() fails.
This actually makes the function mlx4_devlink_set_init_value()
redundant to using directly devlink_param_driverinit_value_set() and so
removed.
It fixes the following kernel trace:
mlx4_core 0000:00:06.0: devlink set parameter 0 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 1 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 4 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 5 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 3 value failed (err = -95)
Fixes: bd1b51dc66df ("mlx4: Add mlx4 initial parameters table and register it")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Tejun writes:
"cgroup fixes for v4.19-rc7
One cgroup2 threaded mode fix for v4.19-rc7. While threaded mode
isn't used widely (yet) and the bug requires somewhat convoluted
sequence of operations, it causes a userland visible malfunction -
EINVAL on a valid attempt to enable threaded mode. This pull request
contains the fix"
* 'for-4.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Fix dom_cgrp propagation when enabling threaded mode
|
|
When booting kernel with LOCKDEP option, below warning info was found:
WARNING: possible recursive locking detected
4.19.0-rc7+ #14 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
but task is already holding lock:
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&list->lock)->rlock#4);
lock(&(&list->lock)->rlock#4);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by swapper/0/1:
#0: 00000000f7539d34 (pernet_ops_rwsem){+.+.}, at:
register_pernet_subsys+0x19/0x40 net/core/net_namespace.c:1051
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
spin_lock_bh include/linux/spinlock.h:334 [inline]
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
stack backtrace:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.0-rc7+ #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1af/0x295 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1759 [inline]
check_deadlock kernel/locking/lockdep.c:1803 [inline]
validate_chain kernel/locking/lockdep.c:2399 [inline]
__lock_acquire+0xf1e/0x3c60 kernel/locking/lockdep.c:3411
lock_acquire+0x1db/0x520 kernel/locking/lockdep.c:3900
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
tipc_link_bc_create+0xb5/0x1f0 net/tipc/link.c:526
tipc_bcast_init+0x59b/0xab0 net/tipc/bcast.c:521
tipc_init_net+0x472/0x610 net/tipc/core.c:82
ops_init+0xf7/0x520 net/core/net_namespace.c:129
__register_pernet_operations net/core/net_namespace.c:940 [inline]
register_pernet_operations+0x453/0xac0 net/core/net_namespace.c:1011
register_pernet_subsys+0x28/0x40 net/core/net_namespace.c:1052
tipc_init+0x83/0x104 net/tipc/core.c:140
do_one_initcall+0x109/0x70a init/main.c:885
do_initcall_level init/main.c:953 [inline]
do_initcalls init/main.c:961 [inline]
do_basic_setup init/main.c:979 [inline]
kernel_init_freeable+0x4bd/0x57f init/main.c:1144
kernel_init+0x13/0x180 init/main.c:1063
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:413
The reason why the noise above was complained by LOCKDEP is because we
nested to hold l->wakeupq.lock and l->inputq->lock in tipc_link_reset
function. In fact it's unnecessary to move skb buffer from l->wakeupq
queue to l->inputq queue while holding the two locks at the same time.
Instead, we can move skb buffers in l->wakeupq queue to a temporary
list first and then move the buffers of the temporary list to l->inputq
queue, which is also safe for us.
Fixes: 3f32d0be6c16 ("tipc: lock wakeup & inputq at tipc_link_reset()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Masahiro writes:
"Kbuild fixes for v4.19 (2nd)
- Fix warnings from recordmcount.pl when building with Clang
- Allow Clang to use GNU toolchains correctly
- Disable CONFIG_SAMPLES for UML to avoid build error"
* tag 'kbuild-fixes-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
samples: disable CONFIG_SAMPLES for UML
kbuild: allow to use GCC toolchain not in Clang search path
ftrace: Build with CPPFLAGS to get -Qunused-arguments
|
|
The ip_defrag.sh script requires bash-style output redirection but
use the default shell. This may cause random failures if the default
shell is not bash.
Address the above using posix compliant output redirection.
Fixes: 02c7f38b7ace ("selftests/net: add ip_defrag selftest")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With CONFIG_THERMAL=m, we get a build error:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c: In function 'cxgb4_thermal_get_trip_type':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c:48:11: error: 'struct adapter' has no member named 'ch_thermal'
Once that is fixed by using IS_ENABLED() checks, we get a link error
against the thermal subsystem when cxgb4 is built-in:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x180): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1e0): undefined reference to `thermal_zone_device_unregister'
Finally, since CONFIG_THERMAL can be =m, the Makefile fails to pick up the
extra file into built-in.a, and we get another link failure against the
cxgb4_thermal_init/cxgb4_thermal_remove files, so the Makefile has to
be adapted as well to work for both CONFIG_THERMAL=y and =m.
Fixes: b18719157762 ("cxgb4: Add thermal zone support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
net: explicitly requires bash when needed.
Some test scripts require bash-only features but use the default shell.
This may cause random failures if the default shell is not bash.
Instead of doing a potentially complex rewrite of such scripts, these patches
require the bash interpreter, where needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The udpgso_bench.sh script requires several bash-only features. This
may cause random failures if the default shell is not bash.
Address the above explicitly requiring bash as the script interpreter
Fixes: 3a687bef148d ("selftests: udp gso benchmark")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the script rtnetlink.sh requires a bash-only features (sleep with sub-second
precision). This may cause random test failure if the default shell is not
bash.
Address the above explicitly requiring bash as the script interpreter.
Fixes: 33b01b7b4f19 ("selftests: add rtnetlink test script")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Arthur Kiyanovski says:
====================
Improving performance and reducing latencies, by using latest capabilities exposed in ENA device
This patchset introduces the following:
1. A new placement policy of Tx headers and descriptors, which takes
advantage of an option to place headers + descriptors in device memory
space. This is sometimes referred to as LLQ - low latency queue.
The patch set defines the admin capability, maps the device memory as
write-combined, and adds a mode in transmit datapath to do header +
descriptor placement on the device.
2. Support for RX checksum offloading
3. Miscelaneous small improvements and code cleanups
Note: V1 of this patchset was created as if patches e2a322a 248ab77
from net were applied to net-next before applying the patchset. This V2
version does not assume this, and should be applyed directly on net-next
without the aformentioned patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove redundant spinlock acquire parameter from ena_com_admin_init()
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improves socket memory utilization when receiving packets larger
than 128 bytes (the previous rx copybreak) and smaller than 256 bytes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently Rx refill is done when the number of required descriptors is
above 1/8 queue size. With a default of 1024 entries per queue the
threshold is 128 descriptors.
There is intention to increase the queue size to 8196 entries.
In this case threshold of 1024 descriptors is too large and can hurt
latency.
Add another limitation to Rx threshold to be at most 256 descriptors.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set skb->ip_summed to the correct value as reported by the device.
Add counter for the case where rx csum offload is enabled but
device didn't check it.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch includes all code changes necessary in ena_netdev to enable
packet sending via the LLQ placemnt mode.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces APIs for detection, initialization, configuration
and actual usage of low latency queues(LLQ). It extends transmit API with
creation of LLQ descriptors in device memory (which include host buffers
descriptors as well as packet header)
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Low Latency Queues(LLQ) allow usage of device's memory for descriptors
and headers. Such queues decrease processing time since data is already
located on the device when driver rings the doorbell.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new fields and definitions to host info and fill them
according to the latest ENA spec version.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce fastpath overhead by making ena_com_tx_comp_req_id_get() inline.
Also move it to ena_eth_com.h file with its dependency function
ena_com_cq_inc_head().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Kees writes:
"Fix open-coded multiplication arguments to allocators
- Fixes several new open-coded multiplications added in the 4.19
merge window."
* tag 'alloc-args-v4.19-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Replace more open-coded allocation size multiplications
|
|
Ido Schimmel says:
====================
mlxsw: Preparations for VxLAN support
This patchset prepares mlxsw for VxLAN support. It contains small and
mostly non-functional changes.
The first eight patches perform small changes in the code to make it
more receptive towards the actual VxLAN changes in the next patchset.
Patches 9-17 add the registers used to configure the device for VxLAN
offload.
Last two patches add the required resources and trap IDs.
The next patchset is available here [1].
1. https://github.com/idosch/linux/tree/vxlan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.
The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.
Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the following resources to be used by the NVE code:
* Number of IPv4 underlay destination IPs in a single TNUMT record
* Number of IPv6 underlay destination IPs in a single TNUMT record
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register is used for setting up the parsing for hash, policy-engine
and routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
