summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-11-14Bluetooth: btintel_pcie: Add recovery mechanismKiran K
This patch adds a recovery mechanism to recover controller if firmware download fails due to unresponsive controller, command timeout, firmware signature verification failure etc. Driver attmepts maximum of 5 times before giving up. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btintel_pcie: Add handshake between driver and firmwareKiran K
The following handshake mechanism needs be followed after firmware download is completed to bring the firmware to running state. After firmware fragments of Operational image are downloaded and secure sends result of the image succeeds, 1. Driver sends HCI Intel reset with boot option #1 to switch FW image. 2. FW sends Alive GP[0] MSIx 3. Driver enables data path (doorbell 0x460 for RBDs, etc...) 4. Driver gets Bootup event from firmware 5. Driver performs D0 entry to device (WRITE to IPC_Sleep_Control =0x0) 6. FW sends Alive GP[0] MSIx 7. Device host interface is fully set for BT protocol stack operation. 8. Driver may optionally get debug event with ID 0x97 which can be dropped For Intermediate loadger image, all the above steps are applicable expcept #5 and #6. On HCI_OP_RESET, firmware raises alive interrupt. Driver needs to wait for it before passing control over to bluetooth stack. Co-developed-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com> Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: hci_core: Fix not checking skb length on hci_scodata_packetLuiz Augusto von Dentz
This fixes not checking if skb really contains an SCO header otherwise the code may attempt to access some uninitilized/invalid memory past the valid skb->data. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: hci_core: Fix not checking skb length on hci_acldata_packetLuiz Augusto von Dentz
This fixes not checking if skb really contains an ACL header otherwise the code may attempt to access some uninitilized/invalid memory past the valid skb->data. Reported-by: syzbot+6ea290ba76d8c1eb1ac2@syzkaller.appspotmail.com Tested-by: syzbot+6ea290ba76d8c1eb1ac2@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6ea290ba76d8c1eb1ac2 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btnxpuart: Add GPIO support to power save featureNeeraj Sanjay Kale
This adds support for driving the chip into sleep or wakeup with a GPIO. If the device tree property device-wakeup-gpios is defined, the driver utilizes this GPIO for controlling the chip's power save state, else it uses the default UART-break method. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14dt-bindings: net: bluetooth: nxp: Add support for power save feature using GPIONeeraj Sanjay Kale
This adds a new optional device tree property device-wakeup-gpios, which specifies the GPIO connected to BT_WAKE_IN pin of the NXP chipset. If this property is defined, the driver will use this GPIO for driving chip into sleep/wakeup state, else use the UART break signal by default. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: hci_conn: Use disable_delayed_work_syncLuiz Augusto von Dentz
This makes use of disable_delayed_work_sync instead cancel_delayed_work_sync as it not only cancel the ongoing work but also disables new submit which is disarable since the object holding the work is about to be freed. Reported-by: syzbot+2446dd3cb07277388db6@syzkaller.appspotmail.com Tested-by: syzbot+2446dd3cb07277388db6@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=2446dd3cb07277388db6 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add USB HW IDs for MT7920/MT7925Jiande Lu
Add HW IDs for wireless module. These HW IDs are extracted from Windows driver inf file and the test for card bring up successful. MT7920 HW IDs test with below patch. https://patchwork.kernel.org/project/bluetooth/ patch/20240930081257.23975-1-chris.lu@mediatek.com/ Patch has been tested successfully and controller is recognized devices pair successfully. MT7920 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20240930111457 Bluetooth: hci0: Device setup in 143004 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: hci0: AOSP quality report is supported Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <jiande.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add RTL8852BE device 0489:e123 to device tablesHilda Wu
Add the support ID 0489:e123 to usb_device_id table for Realtek RTL8852B chip. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e123 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14bluetooth: Fix typos in the commentsYan Zhen
Correctly spelled comments make it easier for the reader to understand the code. Fix typos: 'fragement' ==> 'fragment', 'genration' ==> 'generation', 'funciton' ==> 'function', 'Explitly' ==> 'Explicitly', 'explaination' ==> 'explanation', 'Tranlate' ==> 'Translate', 'immediatelly' ==> 'immediately', 'isntance' ==> 'instance', 'transmittion' ==> 'transmission', 'recevie' ==> 'receive', 'outselves' ==> 'ourselves', 'conrol' ==> 'control'. Signed-off-by: Yan Zhen <yanzhen@vivo.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: hci_conn: Reduce hci_conn_drop() calls in two functionsMarkus Elfring
An hci_conn_drop() call was immediately used after a null pointer check for an hci_conn_link() call in two function implementations. Thus call such a function only once instead directly before the checks. This issue was transformed by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btnxpuart: Rename IW615 to IW610Neeraj Sanjay Kale
This changes the chip name of IW615 to IW610. IW610 (formerly called IW615) is yet to be released to broad market, hence there is no issue of backward compatibility. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btnxpuart: Drop _v0 suffix from FW namesNeeraj Sanjay Kale
This updates all FW names by dropping the _v0 suffix. Its been decided that all NXP BT/ WiFi FW names won't support _v0 suffix. The suffix would be kept for next HW versions such as v1, v2 and so on, which do not have backward compatible FW. This change affects W8987, IW416 and IW615 chipsets, out of which new FW files for W8987 and IW615 are yet to be released to broad market. For IW416, old and new FW names are added to maintain backward compatibility for existing customers. Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add one more ID 0x13d3:0x3623 for Qualcomm WCN785xZijun Hu
Add one more part with ID (0x13d3, 0x3623) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3623 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: Add one more ID 0x0489:0xe0f3 for Qualcomm WCN785xZijun Hu
Add one more part with ID (0x0489, 0xe0f3) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f3 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: add Foxconn 0xe0fc for Qualcomm WCN785xAaron Ma
Firmwares are already in upstream. kernel boot log as following: Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00190200.bin Bluetooth: hci0: QCA: patch rome 0x190200 build 0x5656, firmware rome 0x190200 build 0x43fb Bluetooth: hci0: using NVM file: qca/nvm_usb_00190200.bin Paired BT headphone, output is good. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0fc Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: change the conditions for ISO interfaceChris Lu
Change conditions for Bluetooth driver claiming and releasing usb ISO interface for MediaTek ISO data transmission. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: add intf release flow when usb disconnectChris Lu
MediaTek claim an special usb intr interface for ISO data transmission. The interface need to be released before unregistering hci device when usb disconnect. Removing BT usb dongle without properly releasing the interface may cause Kernel panic while unregister hci device. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: add callback function in btusb_disconnectChris Lu
Add disconnect callback function in btusb_disconnect which is reserved for vendor specific usage before deregister hci in btusb_disconnect. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14Bluetooth: btusb: mediatek: move Bluetooth power off command positionChris Lu
Move MediaTek Bluetooth power off command before releasing usb ISO interface. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2024-11-14eth: fbnic: Add support to dump registersMohsin Bashir
Add support for the 'ethtool -d <dev>' command to retrieve and print a register dump for fbnic. The dump defaults to version 1 and consists of two parts: all the register sections that can be dumped linearly, and an RPC RAM section that is structured in an interleaved fashion and requires special handling. For each register section, the dump also contains the start and end boundary information which can simplify parsing. Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com> Link: https://patch.msgid.link/20241112222605.3303211-1-mohsin.bashr@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-11-13Merge branch 'net-dsa-microchip-add-lan9646-switch-support'Jakub Kicinski
Tristram Ha says: ==================== net: dsa: microchip: Add LAN9646 switch support This series of patches is to add LAN9646 switch support to the KSZ DSA driver. ==================== Link: https://patch.msgid.link/20241109015705.82685-1-Tristram.Ha@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: dsa: microchip: Add LAN9646 switch support to KSZ DSA driverTristram Ha
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has 4 internal PHYs and 1 SGMII port. The chip id read from hardware is same as KSZ9477, so software driver needs to create a new chip id and group allowable functions under its chip data structure to differentiate the product. Signed-off-by: Tristram Ha <tristram.ha@microchip.com> Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13dt-bindings: net: dsa: microchip: Add LAN9646 switch supportTristram Ha
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has 4 internal PHYs and 1 SGMII port. Signed-off-by: Tristram Ha <tristram.ha@microchip.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://patch.msgid.link/20241109015705.82685-2-Tristram.Ha@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13Merge branch 'support-external-snapshots-on-dwmac1000'Jakub Kicinski
Maxime Chevallier says: ==================== Support external snapshots on dwmac1000 The main change since v3 is the move of the fifo flush wait in the ptp_clock_info enable() function within the mutex that protects the ptp registers. Thanks Jakub and Paolo for spotting this. This series also aggregates Daniel's reviews, except for the patch 4 which was modified since then. This series is another take on the previous work [1] done by Alexis Lothoré, that fixes the support for external snapshots timestamping in GMAC3-based devices. Details on why this is needed are mentionned on the cover [2] from V1. [1]: https://lore.kernel.org/netdev/20230616100409.164583-1-alexis.lothore@bootlin.com/ [2]: https://lore.kernel.org/netdev/20241029115419.1160201-1-maxime.chevallier@bootlin.com/ Link to V1: https://lore.kernel.org/netdev/20241029115419.1160201-1-maxime.chevallier@bootlin.com/ Link to V2: https://lore.kernel.org/netdev/20241104170251.2202270-1-maxime.chevallier@bootlin.com/ Link to V3: https://lore.kernel.org/netdev/20241106090331.56519-1-maxime.chevallier@bootlin.com/ ==================== Link: https://patch.msgid.link/20241112170658.2388529-1-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: dwmac_socfpga: This platform has GMACMaxime Chevallier
Indicate that dwmac_socfpga has a gmac. This will make sure that gmac-specific interrupt processing is done, including timestamp interrupt handling. Without this, the external snapshot interrupt is never ack'd and we have an interrupt storm on external snapshot event. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-10-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Configure only the relevant bits for timestamping setupMaxime Chevallier
The PTP_TCR (Timestamp Control Register) is used to configure several features related to packet timestamping. On one hand, it configures the 1588 packet processing, to indicate what types of frames should be timestamped (all, only 1588v1 or 1588v2, using L2 or L4 timestamping, on IPv4 or IPv6, etc.). This is congfigured usually through the ioctl / ndo dedicated for such setup. This configuration is done by setting some fields in that register, that seem to behave the same way on all dwmac variants, including DWMAC1000. On the other hand, and only on DWMAC1000 apparently, some fields in that register are used to configure external snapshots (bits 24/25). On DWMAC4 and others, these fields are reserved and external snapshots are configured through a dedicated register that simply doesn't seem to exist on DWMAC1000. This configuration is done in the dwmac1000-specific ptp_clock_info ops (cf dwmac1000_ptp_enable()). So to avoid the timestamping configuration interfering with the external snapshots, this commit makes sure that the config_hw_tstamping only configures the relevant bits in PTP_TCR, so that the DWMAC1000 timestamping can correctly rely on these otherwise reserved fields. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-9-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Don't include dwmac4 definitions in stmmac_ptpMaxime Chevallier
The stmmac_ptp code doesn't need the dwmac4 register definitions, remove the inclusion. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-8-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Enable timestamping interrupt on dwmac1000Maxime Chevallier
The default configuration for the interrupts on dwmac1000 have the timestamping interrupt masked. Now that the timestamping has been adapted to dwmac1000, enable the timestamping interrupt on these platforms. On dwmac1000, the external snapshot interrupt is configured through a dedicated bit, that is set as reserved on other dwmac variants. The timestaming interrupt is acknowledged by reading the GMAC3_X_TIMESTAMP_STATUS register. Make sure that this interrupt is enabled when snapshot is enabled, and masked when disabled. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-7-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Introduce dwmac1000 timestamping operationsMaxime Chevallier
In GMAC3_X, the timestamping configuration differs from GMAC4 in the layout of the registers accessed to grab the number of snapshots in FIFO as well as the register offset to grab the aux snapshot timestamp. Introduce dedicated ops to configure timestamping on dwmac100 and dwmac1000. The latency correction doesn't seem to exist on GMAC3, so its corresponding operation isn't populated. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-6-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Introduce dwmac1000 ptp_clock_info and operationsMaxime Chevallier
The PTP configuration for GMAC3_X differs from the other implementations in several ways : - There's only one external snapshot trigger - The snapshot configuration is done through the PTP_TCR register, whereas the other dwmac variants have a dedicated ACR (auxiliary control reg) for that purpose - The layout for the PTP_TCR register also differs, as bits 24/25 are used for the snapshot configuration. These bits are reserved on other variants. On GMAC3_X, we also can't discover the number of snapshot triggers automatically. The GMAC3_X has one PPS output, however it's configuration isn't supported yet so report 0 n_per_out for now. Introduce a dedicated set of ptp_clock_info ops and configuration parameters to reflect these differences specific to GMAC3_X. This was tested on dwmac_socfpga. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-5-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Only update the auto-discovered PTP clock featuresMaxime Chevallier
Some DWMAC variants such as dwmac1000 don't support discovering the number of output pps and auxiliary snapshots. Allow these parameters to be defined in default ptp_clock_info, and let them be updated only when the feature discovery yielded a result. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-4-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Use per-hw ptp clock opsMaxime Chevallier
The auxiliary snapshot configuration was found to differ depending on the dwmac version. To prepare supporting this, allow specifying the ptp_clock_info ops in the hwif array Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-3-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: stmmac: Don't modify the global ptp ops directlyMaxime Chevallier
The stmmac_ptp_clock_ops are copied into the stmmac_priv structure before being registered to the PTP core. Some adjustments are made prior to that, such as the number of snapshots or max adjustment parameters. Instead of modifying the global definition, then copying into the local private data, let's first copy then modify the local parameters. Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20241112170658.2388529-2-maxime.chevallier@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: phy: c45: don't use temporary linkmode bitmaps in ↵Heiner Kallweit
genphy_c45_ethtool_get_eee genphy_c45_eee_is_active() populates both bitmaps only if it returns successfully. So we can avoid the overhead of the temporary bitmaps. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/b0832102-28ab-4223-b879-91fb1fc11278@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13net: simplify eeecfg_mac_can_tx_lpiHeiner Kallweit
Simplify the function. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/f9a4623b-b94c-466c-8733-62057c6d9a17@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13ynl: samples: Fix the wrong format specifierLuo Yifan
Make a minor change to eliminate a static checker warning. The type of s->ifc is unsigned int, so the correct format specifier should be %u instead of %d. Signed-off-by: Luo Yifan <luoyifan@cmss.chinamobile.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20241113011142.290474-1-luoyifan@cmss.chinamobile.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13Merge branch 'tools-ynl-two-patches-to-ease-building-with-rpmbuild'Jakub Kicinski
Jan Stancek says: ==================== tools: ynl: two patches to ease building with rpmbuild I'm looking to build and package ynl for Fedora and Centos Stream users. Default rpmbuild has couple hardening options enabled by default [1][2], which currently prevent ynl from building. This series contains 2 small patches to address it. [1] https://fedoraproject.org/wiki/Changes/Harden_All_Packages [2] https://fedoraproject.org/wiki/Changes/PythonSafePath ==================== Link: https://patch.msgid.link/cover.1731399562.git.jstancek@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13tools: ynl: extend CFLAGS to keep options from environmentJan Stancek
Package build environments like Fedora rpmbuild introduced hardening options (e.g. -pie -Wl,-z,now) by passing a -spec option to CFLAGS and LDFLAGS. ynl Makefiles currently override CFLAGS but not LDFLAGS, which leads to a mismatch and build failure: CC sample devlink /usr/bin/ld: devlink.o: relocation R_X86_64_32 against symbol `ynl_devlink_family' can not be used when making a PIE object; recompile with -fPIE /usr/bin/ld: failed to set dynamic section sizes: bad value collect2: error: ld returned 1 exit status Extend CFLAGS to support hardening options set by build environment. Signed-off-by: Jan Stancek <jstancek@redhat.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/265b2d5d3a6d4721a161219f081058ed47dc846a.1731399562.git.jstancek@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13tools: ynl: add script dir to sys.pathJan Stancek
Python options like PYTHONSAFEPATH or -P [1] do not add script directory to PYTHONPATH. ynl depends on this path to build and run. [1] This option is default for Fedora rpmbuild since introduction of https://fedoraproject.org/wiki/Changes/PythonSafePath Signed-off-by: Jan Stancek <jstancek@redhat.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/b26537cdb6e1b24435b50b2ef81d71f31c630bc1.1731399562.git.jstancek@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13Merge tag 'wireless-next-2024-11-13' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.13 Most likely the last -next pull request for v6.13. Most changes are in Realtek and Qualcomm drivers, otherwise not really anything noteworthy. Major changes: mac80211 * EHT 1024 aggregation size for transmissions ath12k * switch to using wiphy_lock() and remove ar->conf_mutex * firmware coredump collection support * add debugfs support for a multitude of statistics ath11k * dt: document WCN6855 hardware inputs ath9k * remove include/linux/ath9k_platform.h ath5k * Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support rtw88: * 8821au and 8812au USB adapters support rtw89 * thermal protection * firmware secure boot for WiFi 6 chip * tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits) Revert "wifi: iwlegacy: do not skip frames with bad FCS" wifi: mac80211: pass MBSSID config by reference wifi: mac80211: Support EHT 1024 aggregation size in TX net: rfkill: gpio: Add check for clk_enable() wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw() wifi: Switch back to struct platform_driver::remove() wifi: ipw2x00: libipw_rx_any(): fix bad alignment wifi: brcmfmac: release 'root' node in all execution paths wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA wifi: iwlwifi: bump minimum API version in BZ/SC to 92 wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h wifi: iwlwifi: be less noisy if the NIC is dead in S3 wifi: iwlwifi: mvm: tell iwlmei when we finished suspending wifi: iwlwifi: allow fast resume on ax200 wifi: iwlwifi: mvm: support new initiator and responder command version wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency wifi: iwlwifi: mvm: MLO scan upon channel condition degradation wifi: iwlwifi: mvm: support new versions of the wowlan APIs wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif() ... ==================== Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-11-13Merge branch 'phy-mediatek-reorg'David S. Miller
Sky Huang says: ==================== Re-organize MediaTek ethernet phy drivers and propose mtk-phy-lib This patchset comes from patch 1/9, 3/9, 4/9, 5/9 and 7/9 of: https://lore.kernel.org/netdev/20241004102413.5838-1-SkyLake.Huang@mediatek.com/ This patchset changes MediaTek's ethernet phy's folder structure and integrates helper functions, including LED & token ring manipulation, into mtk-phy-lib. --- Change in v2: - Add correct Reviewed-by tag in each patch. Change in v3: [patch 4/5] - Fix kernel test robot error by adding missing MTK_NET_PHYLIB. ==================== Signed-off-by: Sky Huang <skylake.huang@mediatek.com>
2024-11-13net: phy: mediatek: add MT7530 & MT7531's PHY ID macrosSkyLake.Huang
This patch adds MT7530 & MT7531's PHY ID macros in mtk-ge.c so that it follows the same rule of mtk-ge-soc.c. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13net: phy: mediatek: Integrate read/write page helper functionsSkyLake.Huang
This patch integrates read/write page helper functions as MTK phy lib. They are basically the same in mtk-ge.c & mtk-ge-soc.c. Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13net: phy: mediatek: Improve readability of mtk-phy-lib.c's ↵SkyLake.Huang
mtk_phy_led_hw_ctrl_set() This patch removes parens around TRIGGER_NETDEV_RX/TRIGGER_NETDEV_TX in mtk_phy_led_hw_ctrl_set(), which improves readability. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13net: phy: mediatek: Move LED helper functions into mtk phy libSkyLake.Huang
This patch creates mtk-phy-lib.c & mtk-phy.h and integrates mtk-ge-soc.c's LED helper functions so that we can use those helper functions in other MTK's ethernet phy driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13net: phy: mediatek: Re-organize MediaTek ethernet phy driversSkyLake.Huang
Re-organize MediaTek ethernet phy driver files and get ready to integrate some common functions and add new 2.5G phy driver. mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988 mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988 Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13Merge branch 'octeontx2-rvu-rep'David S. Miller
Geetha sowjanya says: ==================== Introduce RVU representors This series adds representor support for each rvu devices. When switchdev mode is enabled, representor netdev is registered for each rvu device. In implementation of representor model, one NIX HW LF with multiple SQ and RQ is reserved, where each RQ and SQ of the LF are mapped to a representor. A loopback channel is reserved to support packet path between representors and VFs. CN10K silicon supports 2 types of MACs, RPM and SDP. This patch set adds representor support for both RPM and SDP MAC interfaces. - Patch 1: Implements basic representor driver. - Patch 2: Add devlink support to create representor netdevs that can be used to manage VFs. - Patch 3: Implements basec netdev_ndo_ops. - Patch 4: Installs tcam rules to route packets between representor and VFs. - Patch 5: Enables fetching VF stats via representor interface - Patch 6: Adds support to sync link state between representors and VFs . - Patch 7: Enables configuring VF MTU via representor netdevs. - Patch 8: Adds representors for sdp MAC. - Patch 9: Adds devlink port support. - Patch 10: Implements offload stats. - Patch 11: Implements tc offload support. - patch 12: Adds documentation for rvu port representor. pci/0002:1c:00.0 Command to create PF/VF representor Rpf1vf0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether f6:43:83:ee:26:21 brd ff:ff:ff:ff:ff:ff Rpf1vf1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 12:b2:54:0e:24:54 brd ff:ff:ff:ff:ff:ff Rpf1vf2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 4a:12:c4:4c:32:62 brd ff:ff:ff:ff:ff:ff Rpf1vf3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether ca:cb:68:0e:e2:6e brd ff:ff:ff:ff:ff:ff Rpf2vf0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 06:cc:ad:b4:f0:93 brd ff:ff:ff:ff:ff:ff ~# devlink port pci/0002:1c:00.0/0: type eth netdev Rpf1vf0 flavour physical port 0 splittable false pci/0002:1c:00.0/1: type eth netdev Rpf1vf1 flavour pcivf controller 0 pfnum 1 vfnum 1 external false splittable false pci/0002:1c:00.0/2: type eth netdev Rpf1vf2 flavour pcivf controller 0 pfnum 1 vfnum 2 external false splittable false pci/0002:1c:00.0/3: type eth netdev Rpf1vf3 flavour pcivf controller 0 pfnum 1 vfnum 3 external false splittable false ----------- v11:v1: - Submitted refactoring changes as a separate patch set. https://lore.kernel.org/netdev/20241023161843.15543-1-gakula@marvell.com/T/ - Moved documentation to a separate patch. - patch 9: Added code changes to forward updated mac address to VF. - Implemented TC offload support. v10-v11: - As suggested by "Jiri Pirko" adjusted the documentation. - Added more commit description to patch1. v9-v10: - Fixed build warning w.r.t documentation. v8-v9: - Updated the documentation. v7-v8: - Implemented offload stats ndo. - Added documentation. v6-v7: - Rebased on top net-next branch. v5-v6: - Addressed review comments provided by "Simon Horman". - Added review tag. v4-v5: - Patch 3: Removed devm_* usage in rvu_rep_create() - Patch 3: Fixed build warnings. v3-v4: - Patch 2 & 3: Fixed coccinelle reported warnings. - Patch 10: Added devlink port support. v2-v3: - Used extack for error messages. - As suggested reworked commit messages. - Fixed sparse warning. v1-v2: -Fixed build warnings. -Address review comments provided by "Kalesh Anakkur Purayil". ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13Documentation: octeontx2: Add Documentation for RVU representorsGeetha sowjanya
Adds documentation for creating and configuring rvu port representors Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-11-13octeontx2-pf: Adds TC offload supportGeetha sowjanya
Implements tc offload support for rvu representors. Usage example: - Add tc rule to drop packets with vlan id 3 using port representor(Rpf1vf0). # tc filter add dev Rpf1vf0 protocol 802.1Q parent ffff: flower vlan_id 3 vlan_ethtype ipv4 skip_sw action drop - Redirect packets with vlan id 5 and IPv4 packets to eth1, after stripping vlan header. # tc filter add dev Rpf1vf0 ingress protocol 802.1Q flower vlan_id 5 vlan_ethtype ipv4 skip_sw action vlan pop action mirred ingress redirect dev eth1 Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-28 09:29:23 +0000