| Age | Commit message (Collapse) | Author |
|---|
|
Added the following packets drop counter:
Device out of buffer - counts packets which were dropped due to full
device internal receive queue.
This counter will be shown on ethtool as a new counter called
dev_out_of_buffer.
The counter is read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the VF LAG is in use, round-robin the TX affinity of channels among
the different ports, if supported by the firmware. Create a set of TISes
per port, while doing round-robin of the channels over the different
sets. Let all SQs of a channel share the same set of TISes.
If lag_tx_port_affinity HCA cap bit is supported, num_lag_ports > 1 and
we aren't the LACP owner (PF in the regular use), assign the affinities,
otherwise use tx_affinity == 0 in TIS context to let the FW assign the
affinities itself. The TISes of the LACP owner are mapped only to the
native physical port.
For VFs, the starting port for round-robin is determined by its vhca_id,
because a VF may have only one channel if attached to a single-core VM.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For better modularity and code sharing.
Function internal change to be introduced in the next patches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix a typo in 'mlx5e_refomrat_wol_mode_mlx5_to_linux' and
'mlx5e_refomrat_wol_mode_linux_to_mlx5' function names:
"refomrat" -> "reformat".
Fixes: 928cfe8745a6 ("net/mlx5e: Wake On LAN support")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 HW spec and bits updates:
1) Aya exposes IP-in-IP capability in mlx5_core.
2) Maxim exposes lag tx port affinity capabilities.
3) Moshe adds VNIC_ENV internal rq counter bits.
4) ODP capabilities for DC transport
Misc updates:
5) Saeed, two compiler warnings cleanups
6) Add XRQ legacy commands opcodes
7) Use refcount_t for refcount
8) fix a -Wstringop-truncation warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Hot on the heels of our last set of fixes are a few more for -rc7.
Two of them are fixing issues with our virtual interrupt controller
implementation in KVM/arm, while the other is a longstanding but
straightforward kallsyms fix which was been acked by Masami and
resolves an initialisation failure in kprobes observed on arm64.
- Fix GICv2 emulation bug (KVM)
- Fix deadlock in virtual GIC interrupt injection code (KVM)
- Fix kprobes blacklist init failure due to broken kallsyms lookup"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm/arm64: vgic-v2: Handle SGI bits in GICD_I{S,C}PENDR0 as WI
KVM: arm/arm64: vgic: Fix potential deadlock when ap_list is long
kallsyms: Don't let kallsyms_lookup_size_offset() fail on retrieving the first symbol
|
|
The de-init routine should be doing the following in order:-
1. Unregister the drm device
2. Shut down the crtcs - failing to do this might cause a connector leakage
See the 'commit 109c4d18e574 ("drm/arm/malidp: Ensure that the crtcs are
shutdown before removing any encoder/connector")'
3. Disable the interrupts
4. Unbind the components
5. Free up DRM mode_config info
Changes from v1:-
1. Re-ordered the header files inclusion
2. Rebased on top of the latest drm-misc-fixes
Signed-off-by:. Ayan Kumar Halder <Ayan.Halder@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Link: https://patchwork.freedesktop.org/patch/327606/
|
|
GCC9 build warning
One of the very few warnings I have in the current build comes from
arch/x86/boot/edd.c, where I get the following with a gcc9 build:
arch/x86/boot/edd.c: In function ‘query_edd’:
arch/x86/boot/edd.c:148:11: warning: taking address of packed member of ‘struct boot_params’ may result in an unaligned pointer value [-Waddress-of-packed-member]
148 | mbrptr = boot_params.edd_mbr_sig_buffer;
| ^~~~~~~~~~~
This warning triggers because we throw away all the CFLAGS and then make
a new set for REALMODE_CFLAGS, so the -Wno-address-of-packed-member we
added in the following commit is not present:
6f303d60534c ("gcc-9: silence 'address-of-packed-member' warning")
The simplest solution for now is to adjust the warning for this version
of CFLAGS as well, but it would definitely make sense to examine whether
REALMODE_CFLAGS could be derived from CFLAGS, so that it picks up changes
in the compiler flags environment automatically.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Walking the address list of an inet6_dev requires
appropriate locking. Since the called function
siw_listen_address() may sleep, we have to use
rtnl_lock() instead of read_lock_bh().
Also introduces sanity checks if we got a device
from in_dev_get() or in6_dev_get().
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: 6c52fdc244b5 ("rdma/siw: connection management")
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20190828130355.22830-1-bmt@zurich.ibm.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The parent image is read only up to the overlap point, the rest of
the buffer should be zeroed. This snuck in because as it turns out
the overlap test case has not been triggering this code path for
a while now.
Fixes: a9b67e69949d ("rbd: replace obj_req->tried_parent with obj_req->read_state")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
In set_secret(), key->tfm is assigned to NULL on line 55, and then
ceph_crypto_key_destroy(key) is executed.
ceph_crypto_key_destroy(key)
crypto_free_sync_skcipher(key->tfm)
crypto_free_skcipher(&tfm->base);
This happens to work because crypto_sync_skcipher is a trivial wrapper
around crypto_skcipher: &tfm->base is still 0 and crypto_free_skcipher()
handles that. Let's not rely on the layout of crypto_sync_skcipher.
This bug is found by a static analysis tool STCheck written by us.
Fixes: 69d6302b65a8 ("libceph: Remove VLA usage of skcipher").
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
A guest is not allowed to inject a SGI (or clear its pending state)
by writing to GICD_ISPENDR0 (resp. GICD_ICPENDR0), as these bits are
defined as WI (as per ARM IHI 0048B 4.3.7 and 4.3.8).
Make sure we correctly emulate the architecture.
Fixes: 96b298000db4 ("KVM: arm/arm64: vgic-new: Add PENDING registers handlers")
Cc: stable@vger.kernel.org # 4.7+
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In mlx5_core initialization, query max ODP capabilities for DC transport
from FW and set as current capabilities.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Voon Weifeng says:
====================
stmmac: Add EHL and TGL PCI info and PCI ID
In order to keep PCI info simple and neat, this patch series have
introduced a 3 hierarchy of struct. First layer will be the
intel_mgbe_common_data struct which keeps all Intel common configuration.
Second layer will be xxx_common_data which keeps all the different Intel
microarchitecture, e.g tgl, ehl. The third layer will be configuration
that tied to the PCI ID only based on speed and RGMII/SGMII interface.
EHL and TGL will also having a higher system clock which is 200Mhz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added EHL RGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added TGL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added EHL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek Behún says:
====================
net: dsa: mv88e6xxx: Peridot/Topaz SERDES changes
this is the fifth version of changes for the Topaz/Peridot family of
switches. The patches apply on net-next.
Changes since v4:
- added Reviewed-by and Tested-by tags on first 2 patches, the others
are changed are affected by changes in patch 3/6, so I did not add
the tags, except for 5/6, which is just macro renaming
- patch 3 was changed: the serdes_get_lane returns 0 on success (lane
was discovered), -ENODEV if not lane is present on the port, and
other error if other error occured. Lane is put into a pointer of
type u8
- patches 4 and 6 were affected by this (error detecting from
serdes_get_lane)
- Andrew's complaint about the two additional parameters
(allow_over_2500 and make_cmode_writable) was addressed, by Vivien's
advice: I put a new method into chip operations structure, named
port_set_cmode_writable. This is called from mv88e6xxx_port_setup_mac
just before port_set_cmode. The method is implemented for Topaz.
The check if cmodes over 2500 should be allowed on given port is now
done in the specific port_set_cmode() that requires it, thus the
allow_over_2500 argument is not needed
Again, tested on Turris Mox with Peridot, Topaz, and Peridot + Topaz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Rutsky reported stuck TCP sessions after memory pressure
events. Edge Trigger epoll() user would never receive an EPOLLOUT
notification allowing them to retry a sendmsg().
Jason tested the case of sk_stream_alloc_skb() returning NULL,
but there are other paths that could lead both sendmsg() and sendpage()
to return -1 (EAGAIN), with an empty skb queued on the write queue.
This patch makes sure we remove this empty skb so that
Jason code can detect that the queue is empty, and
call sk->sk_write_space(sk) accordingly.
Fixes: ce5ec440994b ("tcp: ensure epoll edge trigger wakeup when write queue is empty")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Reported-by: Vladimir Rutsky <rutsky@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rds6_inc_info_copy() function has a couple struct members which
are leaking stack information. The ->tos field should hold actual
information and the ->flags field needs to be zeroed out.
Fixes: 3eb450367d08 ("rds: add type of service(tos) infrastructure")
Fixes: b7ff8b1036f0 ("rds: Extend RDS API for IPv6 support")
Reported-by: 黄ID蝴蝶 <butterflyhuangxx@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
sctp: add SCTP_ECN_SUPPORTED sockopt
This patchset is to make ecn flag per netns and endpoint and then
add SCTP_ECN_SUPPORTED sockopt, as does for other feature flags.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP_ECN_SUPPORTED sockopt will be added to allow users to change
ep ecn flag, and it's similar with other feature flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl net.sctp.ecn_enable is added in this patch. It will allow
users to change the default sctp ecn flag, net.sctp.ecn_enable.
This feature was also required on this thread:
http://lkml.iu.edu/hypermail/linux/kernel/0812.1/01858.html
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.
asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit baeababb5b85d5c4e6c917efe2a1504179438d3b
("tun: return NET_XMIT_DROP for dropped packets"),
when tun_net_xmit drop packets, it will free skb and return NET_XMIT_DROP,
netpoll_send_skb_on_dev will run into following use after free cases:
1. retry netpoll_start_xmit with freed skb;
2. queue freed skb in npinfo->txq.
queue_process will also run into use after free case.
hit netpoll_send_skb_on_dev first case with following kernel log:
[ 117.864773] kernel BUG at mm/slub.c:306!
[ 117.864773] invalid opcode: 0000 [#1] SMP PTI
[ 117.864774] CPU: 3 PID: 2627 Comm: loop_printmsg Kdump: loaded Tainted: P OE 5.3.0-050300rc5-generic #201908182231
[ 117.864775] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 117.864775] RIP: 0010:kmem_cache_free+0x28d/0x2b0
[ 117.864781] Call Trace:
[ 117.864781] ? tun_net_xmit+0x21c/0x460
[ 117.864781] kfree_skbmem+0x4e/0x60
[ 117.864782] kfree_skb+0x3a/0xa0
[ 117.864782] tun_net_xmit+0x21c/0x460
[ 117.864782] netpoll_start_xmit+0x11d/0x1b0
[ 117.864788] netpoll_send_skb_on_dev+0x1b8/0x200
[ 117.864789] __br_forward+0x1b9/0x1e0 [bridge]
[ 117.864789] ? skb_clone+0x53/0xd0
[ 117.864790] ? __skb_clone+0x2e/0x120
[ 117.864790] deliver_clone+0x37/0x50 [bridge]
[ 117.864790] maybe_deliver+0x89/0xc0 [bridge]
[ 117.864791] br_flood+0x6c/0x130 [bridge]
[ 117.864791] br_dev_xmit+0x315/0x3c0 [bridge]
[ 117.864792] netpoll_start_xmit+0x11d/0x1b0
[ 117.864792] netpoll_send_skb_on_dev+0x1b8/0x200
[ 117.864792] netpoll_send_udp+0x2c6/0x3e8
[ 117.864793] write_msg+0xd9/0xf0 [netconsole]
[ 117.864793] console_unlock+0x386/0x4e0
[ 117.864793] vprintk_emit+0x17e/0x280
[ 117.864794] vprintk_default+0x29/0x50
[ 117.864794] vprintk_func+0x4c/0xbc
[ 117.864794] printk+0x58/0x6f
[ 117.864795] loop_fun+0x24/0x41 [printmsg_loop]
[ 117.864795] kthread+0x104/0x140
[ 117.864795] ? 0xffffffffc05b1000
[ 117.864796] ? kthread_park+0x80/0x80
[ 117.864796] ret_from_fork+0x35/0x40
Signed-off-by: Feng Sun <loyou85@gmail.com>
Signed-off-by: Xiaojun Zhao <xiaojunzhao141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c9120752b ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
Simplify DSA handling of VLAN subinterface offload
Depends on Vivien Didelot's patchset:
https://patchwork.ozlabs.org/project/netdev/list/?series=127197&state=*
This patchset removes a few strange-looking guards for -EOPNOTSUPP in
dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid, making that
code path no longer possible.
It also disables the code path for the sja1105 driver, which does
support editing the VLAN table, but not hardware-accelerated VLAN
sub-interfaces, therefore the check in the DSA core would be wrong.
There was no better DSA callback to do this than .port_enable, i.e.
at ndo_open time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch barely supports traffic I/O, and it does that by repurposing
VLANs when there is no bridge that is taking control of them.
Letting DSA declare this netdev feature as supported (see
dsa_slave_create) would mean that VLAN sub-interfaces created on sja1105
switch ports will be hardware offloaded. That means that
net/8021q/vlan_core.c would install the VLAN into the filter tables of
the switch, potentially interfering with the tag_8021q VLANs.
We need to prevent that from happening and not let the 8021q core
offload VLANs to the switch hardware tables. In vlan_filtering=0 modes
of operation, the switch ports can pass through VLAN-tagged frames with
no problem.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After witnessing the discussion in https://lkml.org/lkml/2019/8/14/151
w.r.t. ioctl extensibility, it became clear that such an issue might
prevent that the 3 RSV bits inside the DSA 802.1Q tag might also suffer
the same fate and be useless for further extension.
So clearly specify that the reserved bits should currently be
transmitted as zero and ignored on receive. The DSA tagger already does
this (and has always did), and is the only known user so far (no
Wireshark dissection plugin, etc). So there should be no incompatibility
to speak of.
Fixes: 0471dd429cea ("net: dsa: tag_8021q: Create a stable binary format")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 34786005eca3 ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e827093 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
René van Dorst says:
====================
net: ethernet: mediatek: convert to PHYLINK
These patches converts mediatek driver to PHYLINK API.
v3->v4:
* Phylink improvements and clean-ups after review
v2->v3:
* Phylink improvements and clean-ups after review
v1->v2:
* Rebase for mt76x8 changes
* Phylink improvements and clean-ups after review
* SGMII port doesn't support 2.5Gbit in SGMII mode only in BASE-X mode.
Refactor the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink API
This patch the removes the recently added mediatek,physpeed property.
Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
See mt7622-bananapi-bpi-r64.dts for a working example.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* Re-add SGMII support but now with PHYLINK API support
So the SGMII changes are more clear
* Move SGMII block setup from mtk_gmac_sgmii_path_setup() to
mtk_mac_config()
* Merge mtk_setup_hw_path() into mtk_mac_config()
* Remove mediatek,physpeed property, fixed-link supports now any speed so
speed = <2500>; is now valid with PHYLINK
* Demagic SGMII register values
* Use phylink state to setup fixed-link mode
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This convert the basics to PHYLINK API.
SGMII support is not in this patch.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: explicit programmation of VLAN on CPU ports
When a VLAN is programmed on a user port, every switch of the fabric also
program the CPU ports and the DSA links as part of the VLAN. To do that,
DSA makes use of bitmaps to prepare all members of a VLAN.
While this is expected for DSA links which are used as conduit between
interconnected switches, only the dedicated CPU port of the slave must be
programmed, not all CPU ports of the fabric. This may also cause problems in
other corners of DSA such as the tag_8021q.c driver, which needs to program
its ports manually, CPU port included.
We need the dsa_port_vlan_{add,del} functions and its dsa_port_vid_{add,del}
variants to simply trigger the VLAN programmation without any logic in them,
but they may currently skip the operation based on the bridge device state.
This patchset gets rid of the bitmap operations, and moves the bridge device
check as well as the explicit programmation of CPU ports where they belong,
in the slave code.
While at it, clear the VLAN flags before programming a CPU port, as it
doesn't make sense to forward the PVID flag for example for such ports.
Changes in v2: only clear the PVID flag.
====================
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To 2.22
Signed-off-by: Steve French <stfrench@microsoft.com>
|
