summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-07-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville
2014-07-21mac80211: add support for Rx reordering offloadingMichal Kazior
Some drivers may be performing most of Tx/Rx aggregation on their own (e.g. in firmware) including AddBa/DelBa negotiations but may otherwise require Rx reordering assistance. The patch exports 2 new functions for establishing Rx aggregation sessions in assumption device driver has taken care of the necessary negotiations. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> [fix endian bug] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: fix Rx reordering with RX_FLAG_AMSDU_MOREMichal Kazior
Some drivers (e.g. ath10k) report A-MSDU subframes individually with identical seqno. The A-MPDU Rx reorder code did not account for that which made it practically unusable with drivers using RX_FLAG_AMSDU_MORE because it would end up dropping a lot of frames resulting in confusion in upper network transport layers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: remove useless NULL checksEytan Lifshitz
sdata can't be NULL, and key being NULL is really not possible unless the code is modified. The sdata check made a static analyze (klocwork) unhappy because we would get pointer to local (sdata->local) and only then check if sdata is non-NULL. Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> [remove !key check as well] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: fix a potential NULL access in ieee80211_crypto_hw_decryptMax Stepanov
The NULL pointer access could happen when ieee80211_crypto_hw_decrypt is called from ieee80211_rx_h_decrypt with the following condition: 1. rx->key->conf.cipher is not WEP, CCMP, TKIP or AES_CMAC 2. rx->sta is NULL When ieee80211_crypto_hw_decrypt is called, it verifies rx->sta->cipher_scheme and it will cause Oops if rx->sta is NULL. This path adds an addirional rx->sta == NULL verification in ieee80211_crypto_hw_decrypt for this case. Signed-off-by: Max Stepanov <Max.Stepanov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21wireless: fixup genregdb.awk for remove of antenna gain from wireless-regdLuis R. Rodriguez
Since "wireless-regdb: remove antenna gain" was merged in the wireless-regdb tree, the awk script parser has been incompatible with the 'official' regulatory database. This fixes that up. Without this change the max EIRP is set to 0 making 802.11 devices useless. The fragile nature of the awk parser must be replaced, but ideas over how to do that in the most scalable way are being reviewed. In the meantime update the documentation for CFG80211_INTERNAL_REGDB so folks are aware of expectations for now. Reported-by: John Walker <john@x109.net> Reported-by: Krishna Chaitanya <chaitanya.mgit@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: remove redundant IEEE80211_STA_CSA_RECEIVED flagLuciano Coelho
The csa_active flag was added in sdata a while ago and made IEEE80211_STA_CSA_RECEIVED redundant. The new flag is also used to mark when CSA is ongoing on other iftypes and took over the old one as the preferred method for checking whether we're in the middle of a channel switch. Remove the old, redundant flag. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: make sure TDLS teardown packet is sent on timeLiad Kaufman
Since the teardown packet is created while the queues are stopped, it isn't sent immediately, but rather is pending. To be sure that when we flush the queues prior to destroying the station we also send this packet - the tasklet handling pending packets is invoked to flush the packets. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: ArikX Nemtsov <arik@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: ignore frames between TDLS peers when operating as APArik Nemtsov
If the AP receives actions frames destined for other peers, it may mistakenly toggle BA-sessions from itself to a peer. Ignore TDLS data packets as well - the AP should not handle them. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21cfg80211: fix TDLS setup with VHT peersArik Nemtsov
Some VHT TDLS peers (Google Nexus 5) include the VHT-AID IE in their TDLS setup request/response. Usermode passes this aid as the station aid, causing it to fail verifiction, since this happens in the "set_station" stage. Make an exception for the TDLS use-case. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: disable VHT for TDLSArik Nemtsov
TDLS VHT support requires some more information elements during setup. While these are not there, mask out the peer's VHT capabilities so that VHT rates are not mistakenly used. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: set Rx highest rate in ht_capArik Nemtsov
Set for completeness mostly, currently unused in the code. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: support HT for TDLS stationsArik Nemtsov
Add the HT capabilities and HT operation information elements to TDLS setup packets where appropriate. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: move TDLS data to mgd private partArik Nemtsov
We can only be a station for TDLS connections. Also fix a bug where a delayed work could be left scheduled if the station interface was brought down during TDLS setup. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: add TDLS QoS param IE on setup-confirmArik Nemtsov
When TDLS QoS is supported by the the peer and the local card, add the WMM parameter IE to the setup-confirm frame. Take the QoS settings from the current AP, or if unsupported, use the default values from the specification. This behavior is mandated by IEEE802.11-2012 section 10.22.4. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: add QoS IE during TDLS setup startArik Nemtsov
If QoS is supported by the card, add an appropriate IE to TDLS setup- request and setup-response frames. Consolidate the setting of the WMM info IE across mac80211. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: set TDLS capab to zero on failure framesArik Nemtsov
When sending setup-failure frames, set the capability field to zero, as mandated by the specification (IEEE802.11-2012 8.5.13). Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: avoid adding some IEs on TDLS setup failure packetsArik Nemtsov
Most setup-specific information elements are not to be added when a setup frame is sent with an error status code. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: split extra TDLS IEs in setup framesArik Nemtsov
When building TDLS setup frames, use the IE order mandates in the specification, splitting extra IEs coming from usermode. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: consolidate TDLS IE treatmentArik Nemtsov
Add all information elements for TDLS discovery and setup in the same function. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: fix error path for TDLS setupArik Nemtsov
The patch "8f02e6b mac80211: make sure TDLS peer STA exists during setup" broke TDLS error paths where the STA doesn't exist when sending the error. Fix it by only testing for STA existence during a non-error flow. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-21mac80211: track TDLS initiator internallyArik Nemtsov
Infer the TDLS initiator and track it in mac80211 via a STA flag. This avoids breaking old userspace that doesn't pass it via nl80211 APIs. The only case where userspace will need to pass the initiator is when the STA is removed due to unreachability before a teardown packet is sent. Support for unreachability was only recently added to wpa_supplicant, so it won't be a problem in practice. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-18mwifiex: remove redundant timestamps in debug printsBing Zhao
We don't need wall-clock time here, and in most configurations that care, there are already timestamps in the kernel using CONFIG_PRINTK_TIME=y. Reported-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18mwifiex: do not re-associate when already connectedUjjal Roy
In managed mode if the driver is getting a re-associate command from cfg80211, driver deauthenticates with the AP internally and sends a disconnected event to cfg80211 before completion of its association process. The disconnected event then modifies the SSID length as wdev->ssid_len = 0. So, upon receiving the connect result event from driver, cfg80211 is unable to get that BSS from the device's BSS list and generates the following WARN_ON message. WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658 __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]() Avoid re-association while the device is already associated to a network. Also remove the internal deauthentication from the association path. Signed-off-by: Ujjal Roy <royujjal@gmail.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18mwifiex: remove needless current_bssid variableAvinash Patil
This local variable is not used anywhere in function. Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: N-PHY: update spur avoidance to support newer devicesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: use one shared function for setting MAC frequencyRafał Miłecki
By the way add few chipsets that were tracked with "wl" dumps. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: N-PHY: set band on every channel switchRafał Miłecki
Seems to be required by some hardware, wl does it every time. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: N-PHY: complete 0x2057 radio init calibrationRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: N-PHY: add tables for radio 0x2057 rev 14Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18b43: N-PHY: fix channel switching with 2 GHz radio 0x2057Rafał Miłecki
Values were written to wrong registers. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18ath9k: drop negativity checks for unsigned values coming from kstrtoul()Andrey Utkin
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80471 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80481 Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18ath9k: set up tx power into the MRRLorenzo Bianconi
Set up tx power for each MRR segment in the tx descriptor Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18ath9k: fix pending tx frames accountingFelix Fietkau
Packets originally buffered for the regular hardware tx queues can end up being transmitted through the U-APSD queue (via PS-Poll or U-APSD). When packets are dropped due to retransmit failures, the pending frames counter is not always updated properly. Fix this by keeping track of the queue that a frame was accounted for in the ath_frame_info struct, and using that on completion to decide whether the counter should be updated. This fixes some spurious transmit queue hangs. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18bcma: add support for BCM43217 found in Tenda W322E (14e4:43a9)Rafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18bcma: extract antenna gains from SPROM correctlyRafał Miłecki
Just like in case of SSB SPROMs they are encoded in a bit tricky way. SPROM struct already uses s8 type and it's supposed to store decoded values. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18ssb: extract power info from SPROM revs 4 and 5Rafał Miłecki
This is needed to properly handle early 802.11n devices like BCM4321. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: add new register region for AGC tableVladimir Kondratiev
New register area defined in the firmware Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: map RGF_USER_USAGE_1 on the debugfsVladimir Kondratiev
Firmware sets this register with the offset of the firmware trace area within the peripheral memory region. Critical for the firmware trace to work Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: use same mapping table for FW addr translation and debugfsVladimir Kondratiev
Use single data source for all information regarding the firmware memory map. With this change "ucode_xxx" regions disappears since they are in fact part of larger "upper area" region Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: fix memory leak on error path in wil_write_file_rxon()Vladimir Kondratiev
If copy_from_user() fails, buffer allocated for parameters would leak Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: fix double definition of 'ctx'Vladimir Kondratiev
Variable 'ctx' declarad again in the inner loop. Should use one from outer loop instead. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: export FW/HW versions through debugfsVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: support for "sparrow" hardwareVladimir Kondratiev
New hardware release appears; it require some changes to properly support it. Introduce struct wil_board and "board" attribute in wil6210_priv; keep hardware variant information in this structure. fill it on probe(). Used in the reset flow. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18Merge tag 'for-linville-20140717' of git://github.com/kvalo/athJohn W. Linville
2014-07-18Merge branch 'for-upstream' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
2014-07-18mac80211: suppress unused variable warning without lockdepJohannes Berg
When lockdep isn't compiled, a local variable isn't used (it's only in a macro argument), annotate it to suppress the compiler warning. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-07-16mwifiex: remove redundant TDLS setup action frame check and avoid leaksBing Zhao
The unwanted frame types are already handled in 'default' case of the switch/case below. The str_ptr is allocated but it can be leaked if the length check fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr after the length checks. Reported-by: Paul Stewart <pstew@chromium.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-15ssb: extract antenna gains from SPROMs revs 4+ properlyRafał Miłecki
They are encoded the same way as in older SPROMs. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-15ssb: make code for antenna gain extraction more genericRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-29 10:15:23 +0000