| Age | Commit message (Collapse) | Author |
|---|
|
Remove board specific gpio-fan driver registration. Moved into device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
mv64xxx_of_config requires that the tclk frequency be found
through the clk stuff rather than through device tree, so add
another override for the 2nd controller.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The kirkwood_pcie_scan_bus function duplicates the common code in
bios32.c, passing ops in will use the common code..
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: EXYNOS: DT Support for SATA and SATA PHY
ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
ARM: dts: Add node for touchscreen for exynos4210-trats
ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
ARM: dts: Add node for i2c3 bus for exynos4210-trats
ARM: dts: Add nodes for GPIO keys available on Trats
ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
ARM: dts: Add nodes for pin controllers for exynos4x12
pinctrl: samsung: Add support for EXYNOS4X12
gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
ARM: dts: add board dts file for EXYNOS4412 based SMDK board
ARM: dts: Add support for EXYNOS4X12 SoCs
ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
ARM: EXYNOS: Add MFC device tree support
ARM: dts: Enable serial controllers on Origen and SMDKV310
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
...
Add/add conflicts in:
arch/arm/boot/dts/exynos5250-smdk5250.dts
arch/arm/boot/dts/exynos5250.dtsi
arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
cm-t3517 starting from revision 1.2 does not have the 32K oscilator
wired to the AM3517 SoC.
Therefore switch to use the GPTIMER for system clock.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CONFIG_OMAP_32K_TIMER is kind of standing on the single zImage way.
Make OMAP2+ timer code independant from the CONFIG_OMAP_32K_TIMER
setting.
To remove the dependancy, several conversions/additions had to be done:
1) Timer initialization functions are named by the platform
name and the clock source in use.
This also makes it possible to define and use the GPTIMER as the
clock source instead of the 32K timer on platforms that do not have
the 32K timer ip block or the 32K timer is not wired on the board.
Currently, the the timer is chosen in the machine_desc structure on
per board basis. Later, DT should be used to choose the timer.
2) Settings under the CONFIG_OMAP_32K_TIMER option are used as defaults
and those under !CONFIG_OMAP_32K_TIMER are removed.
This removes the CONFIG_OMAP_32K_TIMER on OMAP2+ timer code.
3) Since we have all the timers defined inside machine_desc structure
and we no longer need the fallback to gp_timer clock source in case
32k_timer clock source is unavailable (namely on AM33xx), we no
longer need the #ifdef around omap2_sync32k_clocksource_init()
function. Remove the #ifdef CONFIG_OMAP_32K_TIMER around the
omap2_sync32k_clocksource_init() function.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
This is for adding support for DT based exynos5250 hdmi and it adds
device node for hdmi, mixer, hdmiphy and hdmiddc.
* 'next/hdmi-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
* 'next/cleanup-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: S3C64XX: Statically define parent clock of "camera" clock
ARM: S3C64XX: Remove duplicated camera clock
ARM: EXYNOS: Add missing static storage class specifiers in clock-exynos5.c
ARM: EXYNOS: Make combiner_of_init function static
ARM: EXYNOS: Make s3c_device_i2c0 always use id 0
ARM: EXYNOS: Remove wrongly placed usb2.0 PHY_CFG definition from PMU_REG
ARM: EXYNOS: reorder inclusions of <linux/platform_data/xxx.h>
ARM: EXYNOS: Remove unused static uart resource information
ARM: EXYNOS: Remove static io-remapping for gic and combiner
ARM: EXYNOS: Remove wrong I2S0 clock from peril clock
ARM: EXYNOS: remove the MMC_CAP2_BROKEN_VOLTAGE
|
|
omap-for-v3.8/timer
|
|
The thing is that team_dev_queue_xmit() returns NET_XMIT_* or -E*.
bc_trasmit() should return true in case all went well. So use ! to get
correct retval from team_dev_queue_xmit() result.
This bug caused iface statistics to be badly computed.
This bug was introduced by:
team: add broadcast mode (5fc889911a99043a97da1daa0d010ad72cbc3042)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A simple pinctrl Kconfig oneliner arriving late.
Final (hopefully) oneliner for the pinctrl subsystem targeted at v3.7"
* tag 'pinctrl-for-v3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/samsung: don't allow enabling pinctrl-samsung standalone
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull selinux RCU fixlet from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix sel_netnode_insert() suspicious rcu dereference
|
|
There have the following warning message when running modules install
for sign ko files:
# make modules_install
...
INSTALL drivers/input/touchscreen/pcap_ts.ko
Found = in conditional, should be == at scripts/sign-file line 164.
Found = in conditional, should be == at scripts/sign-file line 161.
Found = in conditional, should be == at scripts/sign-file line 159.
This patch change replace '=' by '==' in elsif conditions for avoid the
above warning messages.
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
setting of slave devices.
Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An SKB paged fragment can consist of a compound page with order > 0.
However the netchannel protocol deals only in PAGE_SIZE frames.
Handle this in xennet_make_frags by iterating over the frames which
make up the page.
This is the netfront equivalent to 6a8ed462f16b for netback.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: ANNIE LI <annie.li@oracle.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
John W. Linville says:
====================
This is a batch of fixes intended for 3.7...
Included are two pulls. Regarding the mac80211 tree, Johannes says:
"Please pull my mac80211.git tree (see below) to get two more fixes for
3.7. Both fix regressions introduced *before* this cycle that weren't
noticed until now, one for IBSS not cleaning up properly and the other
to add back the "wireless" sysfs directory for Fedora's startup scripts."
Regarding the iwlwifi tree, Johannes says:
"Please also pull my iwlwifi.git tree, I have two fixes: one to remove a
spurious warning that can actually trigger in legitimate situations, and
the other to fix a regression from when monitor mode was changed to use
the "sniffer" firmware mode."
Also included is an nfc tree pull. Samuel says:
"We mostly have pn533 fixes here, 2 memory leaks and an early unlocking fix.
Moreover, we also have an LLCP adapter linked list insertion fix."
On top of that, a few more bits... Albert Pool adds a USB ID
to rtlwifi. Bing Zhao provides two mwifiex fixes -- one to fix
a system hang during a command timeout, and the other to properly
report a suspend error to the MMC core. Finally, Sujith Manoharan
fixes a thinko that would trigger an ath9k hang during device reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies pin control groups of SD pins on EXYNOS4210
and EXYNOS4X12 to use drive strength 3 as a default value which
corresponds to S5P_GPIO_DRVSTR_LV4 in legacy non-DT code.
This is needed at least on Origen board for sdhci2 to work and
if any other drive strength is required on each board, we can
overide it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited commit message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds device tree nodes for power domains available
on EXYNOS4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds a way to specify bindings between devices and power
domains using device tree.
A device can be bound to particular power domain by adding a
power-domain property containing a phandle to the domain. The device
will be bound to the domain before binding a driver to it and unbound
after unbinding a driver from it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds initialization of name field in generic power domain
struct.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Initial state of power domains might vary on different boards and with
different bootloaders.
This patch adds detection of initial state of power domains when being
registered from DT.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds fixed voltage vmmc regulator to dts file of Origen
board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch modifies sdhci nodes present in Origen device tree source
to use current generic mmc bindings.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch updates all parts of Origen dts related to pin configuration
to use new GPIO and pinctrl bindings, instead of (now unsupported on
Exynos4) legacy gpio-samsung bindings.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch changes memory configuration defined in dts file of Origen
board from single 1 GiB section into four 256 MiB sections to match
section size limit.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Needed to match device ids for clocks, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is similar to a recent commit for exynos5250 titled:
ARM: EXYNOS: Add aliases for i2c controller
Adding aliases will be useful to prevent warnings in a future
change. See:
i2c: s3c2410: Get the i2c bus number from alias id
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
===============================
[ INFO: suspicious RCU usage. ]
3.5.0-rc1+ #63 Not tainted
-------------------------------
security/selinux/netnode.c:178 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by trinity-child1/8750:
#0: (sel_netnode_lock){+.....}, at: [<ffffffff812d8f8a>] sel_netnode_sid+0x16a/0x3e0
stack backtrace:
Pid: 8750, comm: trinity-child1 Not tainted 3.5.0-rc1+ #63
Call Trace:
[<ffffffff810cec2d>] lockdep_rcu_suspicious+0xfd/0x130
[<ffffffff812d91d1>] sel_netnode_sid+0x3b1/0x3e0
[<ffffffff812d8e20>] ? sel_netnode_find+0x1a0/0x1a0
[<ffffffff812d24a6>] selinux_socket_bind+0xf6/0x2c0
[<ffffffff810cd1dd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff810cdb55>] ? lock_release_holdtime.part.9+0x15/0x1a0
[<ffffffff81093841>] ? lock_hrtimer_base+0x31/0x60
[<ffffffff812c9536>] security_socket_bind+0x16/0x20
[<ffffffff815550ca>] sys_bind+0x7a/0x100
[<ffffffff816c03d5>] ? sysret_check+0x22/0x5d
[<ffffffff810d392d>] ? trace_hardirqs_on_caller+0x10d/0x1a0
[<ffffffff8133b09e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff816c03a9>] system_call_fastpath+0x16/0x1b
This patch below does what Paul McKenney suggested in the previous thread.
Signed-off-by: Dave Jones <davej@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@parisplace.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Conflicts:
drivers/mtd/nand/nand_base.c
|
|
git://git.linaro.org/people/ljones/linux-3.0-ux500 into next/dt
From Lee Jones. It's an update of the previous ux500/dt branch with a few more
patches:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Describe UART platform registering issues more accurately
ARM: ux500: Enable all MMC devices on the u9540 when booting with DT
ARM: ux500: Enable SDI4 port on the u9540 when booting with Device Tree
ARM: ux500: Add UART support to the u9540 Device Tree
ARM: ux500: Add skeleton DTS file for the u9540
ARM: ux500: Add SDI (MMC) support to the HREF Device Tree
ARM: ux500: Move regulator-name properties out to board DTS files
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If this array is not cleared, the jack related code later might
fail to create "Internal Speaker Phantom Jack" on Dell Inspiron 3420 and
Dell Vostro 2420.
BugLink: https://bugs.launchpad.net/bugs/1076840
Cc: stable@vger.kernel.org (3.6+)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
From Roland Stigge:
DTS updates for the LPC32xx Soc for 3.7
This time, only one patch: Adding the motor PWM to lpc32xx.dtsi
* tag 'lpc32xx-dts-for-3.7' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add the motor PWM to base dts file
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/cleanup
From Stephen Warren:
ARM: bcm2835: cleanup
Just a few minor/trivial cleanups.
* tag 'bcm2835-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: remove useless variables from Makefile.boot
ARM: bcm2835: Fix typo in the error message
ARM: bcm2835: Add missing static modifiers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup for 3.8
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
* tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
iommu: tegra: remove include of <mach/iomap.h>
staging: nvec: remove include of <mach/iomap.h>
crypto: tegra: remove include of <mach/clk.h>
ARM: tegra: update *.dts for regulator-compatible deprecation
usb: phy: tegra remove include of <mach/iomap.h>
usb: host: tegra remove include of <mach/iomap.h>
|
|
We found a new codec ID 292, and that just a simple quirk would enable
sound output/input on this ALC292 chip.
BugLink: https://bugs.launchpad.net/bugs/1081466
Cc: stable@vger.kernel.org
Tested-by: Acelan Kao <acelan.kao@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
next/dt
From Nicolas Ferre:
More DT material for AT91:
- conversion of watchdog to DT
- usart definition for evk-pro3 board
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: evk-pro3: enable watchdog
ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
watchdog: at91sam9_wdt: add device tree support
ARM: at91: dt: evk-pro3: enable uart0 and uart2
|
|
into next/cleanup
From Nicolas Ferre:
Removing unneeded macro.
* tag 'at91-for-next-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91/atmel-mci: remove unused setup_dma_addr() macro
|
|
While these got added in the right place everywhere else, entry_64.S
is the odd one where they ended up before the initial CFI directive(s).
In order to cover the full code ranges, the CFI directive must be
first, though.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/5093BA1F02000078000A600E@nat28.tlf.novell.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Add valid patch size for family 16h processors.
[ hpa: promoting to urgent/stable since it is hw enabling and trivial ]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Acked-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Link: http://lkml.kernel.org/r/1353004910-2204-1-git-send-email-boris.ostrovsky@amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
|
Modules, in particular oprofile (and possibly other similar tools)
need kernel_stack_pointer(), so export it using EXPORT_SYMBOL_GPL().
Cc: Yang Wei <wei.yang@windriver.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Jun Zhang <jun.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
In 32 bit the stack address provided by kernel_stack_pointer() may
point to an invalid range causing NULL pointer access or page faults
while in NMI (see trace below). This happens if called in softirq
context and if the stack is empty. The address at ®s->sp is then
out of range.
Fixing this by checking if regs and ®s->sp are in the same stack
context. Otherwise return the previous stack pointer stored in struct
thread_info. If that address is invalid too, return address of regs.
BUG: unable to handle kernel NULL pointer dereference at 0000000a
IP: [<c1004237>] print_context_stack+0x6e/0x8d
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in:
Pid: 4434, comm: perl Not tainted 3.6.0-rc3-oprofile-i386-standard-g4411a05 #4 Hewlett-Packard HP xw9400 Workstation/0A1Ch
EIP: 0060:[<c1004237>] EFLAGS: 00010093 CPU: 0
EIP is at print_context_stack+0x6e/0x8d
EAX: ffffe000 EBX: 0000000a ECX: f4435f94 EDX: 0000000a
ESI: f4435f94 EDI: f4435f94 EBP: f5409ec0 ESP: f5409ea0
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
CR0: 8005003b CR2: 0000000a CR3: 34ac9000 CR4: 000007d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process perl (pid: 4434, ti=f5408000 task=f5637850 task.ti=f4434000)
Stack:
000003e8 ffffe000 00001ffc f4e39b00 00000000 0000000a f4435f94 c155198c
f5409ef0 c1003723 c155198c f5409f04 00000000 f5409edc 00000000 00000000
f5409ee8 f4435f94 f5409fc4 00000001 f5409f1c c12dce1c 00000000 c155198c
Call Trace:
[<c1003723>] dump_trace+0x7b/0xa1
[<c12dce1c>] x86_backtrace+0x40/0x88
[<c12db712>] ? oprofile_add_sample+0x56/0x84
[<c12db731>] oprofile_add_sample+0x75/0x84
[<c12ddb5b>] op_amd_check_ctrs+0x46/0x260
[<c12dd40d>] profile_exceptions_notify+0x23/0x4c
[<c1395034>] nmi_handle+0x31/0x4a
[<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<c13950ed>] do_nmi+0xa0/0x2ff
[<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<c13949e5>] nmi_stack_correct+0x28/0x2d
[<c1029dc5>] ? ftrace_define_fields_irq_handler_entry+0x45/0x45
[<c1003603>] ? do_softirq+0x4b/0x7f
<IRQ>
[<c102a06f>] irq_exit+0x35/0x5b
[<c1018f56>] smp_apic_timer_interrupt+0x6c/0x7a
[<c1394746>] apic_timer_interrupt+0x2a/0x30
Code: 89 fe eb 08 31 c9 8b 45 0c ff 55 ec 83 c3 04 83 7d 10 00 74 0c 3b 5d 10 73 26 3b 5d e4 73 0c eb 1f 3b 5d f0 76 1a 3b 5d e8 73 15 <8b> 13 89 d0 89 55 e0 e8 ad 42 03 00 85 c0 8b 55 e0 75 a6 eb cc
EIP: [<c1004237>] print_context_stack+0x6e/0x8d SS:ESP 0068:f5409ea0
CR2: 000000000000000a
---[ end trace 62afee3481b00012 ]---
Kernel panic - not syncing: Fatal exception in interrupt
V2:
* add comments to kernel_stack_pointer()
* always return a valid stack address by falling back to the address
of regs
Reported-by: Yang Wei <wei.yang@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/20120912135059.GZ8285@erda.amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jun Zhang <jun.zhang@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
The biggest batch of fixes here is the Kirkwood DMA fixes, plus a couple
of other small fixes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull missed powerpc fixes from Benjamin Herrenschmidt:
"Here are small 52xx fixes that Anatolij asked me to pull a while back
and that I completely missed. The stuff is local to that platform
code, and was in next for a while, so it should still go into 3.7."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mpc5200: move lpbfifo node and fix its interrupt property
powerpc: 52xx: nop out unsupported critical IRQs
powerpc/pcm030: add pcm030-audio-fabric to dts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fix from Konrad Rzeszutek Wilk:
- Fix regression introduced by commit ceb90fa0a800 ("xen/privcmd: add
PRIVCMD_MMAPBATCH_V2 ioctl").
* tag 'stable/for-linus-3.7-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/privcmd: Correctly return success from IOCTL_PRIVCMD_MMAPBATCH
|
