| Age | Commit message (Collapse) | Author |
|---|
|
Fix misspelling in word syndrome.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fixes the bug when turning on/off CQE compression mechanism
resets the RX rings size to default value when it is not
needed.
Fixes: 2fc4bfb7250d ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The assumption that the next header field contains the transport
protocol is wrong for IPv6 packets with extension headers.
Instead, we should look the inner-most next header field in the buffer.
This will fix TSO offload for tunnels over IPv6 with extension headers.
Performance testing: 19.25x improvement, cool!
Measuring bandwidth of 16 threads TCP traffic over IPv6 GRE tap.
CPU: Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
TSO: Enabled
Before: 4,926.24 Mbps
Now : 94,827.91 Mbps
Fixes: b3f63c3d5e2c ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix bug that allows ets bw sum to be 0% when ets tc type exists.
Fixes: 08fb1dacdd76 ('net/mlx5e: Support DCBNL IEEE ETS')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.
In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.
Fixes: 7486216b3a0b ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b23d1 ("net/mlx5: Rate limit tables support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before the offending commit, mlx5 core did the IRQ affinity itself,
and it seems that the new generic code have some drawbacks and one
of them is the lack for user ability to modify irq affinity after
the initial affinity values got assigned.
The issue is still being discussed and a solution in the new generic code
is required, until then we need to revert this patch.
This fixes the following issue:
echo <new affinity> > /proc/irq/<x>/smp_affinity
fails with -EIO
This reverts commit a435393acafbf0ecff4deb3e3cb554b34f0d0664.
Note: kept mlx5_get_vector_affinity in include/linux/mlx5/driver.h since
it is used in mlx5_ib driver.
Fixes: a435393acafb ("mlx5: move affinity hints assignments to generic code")
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jes Sorensen <jsorensen@fb.com>
Reported-by: Jes Sorensen <jsorensen@fb.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, if a size of zero is passed to
mlx5_fpga_mem_{read|write}_i2c()
the "err" return value will not be initialized, which triggers gcc
warnings:
[..]/mlx5/core/fpga/sdk.c:87 mlx5_fpga_mem_read_i2c() error:
uninitialized symbol 'err'.
[..]/mlx5/core/fpga/sdk.c:115 mlx5_fpga_mem_write_i2c() error:
uninitialized symbol 'err'.
fix that.
Fixes: a9956d35d199 ('net/mlx5: FPGA, Add SBU infrastructure')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Simon Horman says:
====================
nfp: flower: add Geneve tunnel support
John Hurley says:
This patchset adds support for offloading the encap and decap of Geneve
tunnels to the NFP. In both cases, specifying well known port 6081 is a
requirement for rule offload.
Geneve firmware support has been recently added, so the patchset includes
the reading of a fw symbol that defines a bitmap of newly supported
features. Geneve will only be offloaded if the fw supports it. The new
symbol is added in fw r5646.
Geneve option fields are not supported as either a match or an action due
there current exclussion from TC flower. Because Geneve (as both a match
and action) behaves the same as other udp tunnels such as VXLAN, generic
functions are created that handle both Geneve and VXLAN. It is anticapated
that these functions will be modified to support options in future
patches.
The removal of an unused variable 'tun_dst_mask' is included as a separate
patch here. This does not affect functionality.
Also included are modifications to the test framework to check that the
new encap and decap features are functioning correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Generate rules for the NFP to encapsulate packets in Geneve tunnels. Move
the vxlan action code to generic udp tunnel actions and use core code for
both vxlan and Geneve.
Only support outputting to well known port 6081. Setting tunnel options
is not supported yet.
Only attempt to offload if the fw supports Geneve.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile Geneve match fields for offloading to the NFP. The addition of
Geneve overflows the 8 bit key_layer field, so apply extended metadata to
the match cmsg allowing up to 32 more key_layer fields.
Rather than adding new Geneve blocks, move the vxlan code to generic ipv4
udp tunnel structs and use these for both vxlan and Geneve.
Matches are only supported when specifically mentioning well known port
6081. Geneve tunnel options are not yet included in the match.
Only offload Geneve if the fw supports it - include check for this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the _abi_flower_extra_features symbol from the fw which gives a 64
bit bitmap of new features (on top of the flower base support) that the fw
can offload. Store this bitmap in the priv data associated with each app.
If the symbol does not exist, set the bitmap to 0.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tunnel dest IP is required for separate offload to the NFP. It is
already verified that a dest IP must be present and must be an exact
match in the flower rule. Therefore, we can just extract the IP from the
generated offload rule and remove the unused mask variable. The function
is then no longer required to return the IP separately.
Because tun_dst is localised to tunnel matches, move the declaration to
the tunnel if branch.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our MMC host driver now issues a reset, instead of just deasserting
the reset control, since commit c34eda69ad4c ("mmc: sunxi: Reset the
device at probe time"). The sun9i-mmc clock driver does not support
this, and will fail, which results in MMC not probing.
This patch implements the reset callback by asserting the reset control,
then deasserting it after a small delay.
Fixes: 7a6fca879f59 ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Cc: <stable@vger.kernel.org> # 4.14.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171218035751.20661-1-wens@csie.org
|
|
The recently added fib_metrics_match() causes a regression for routes
with both RTAX_FEATURES and RTAX_CC_ALGO if the latter has
TCP_CONG_NEEDS_ECN flag set:
| # ip link add d0 type dummy
| # ip link set d0 up
| # ip route add 172.29.29.0/24 dev d0 features ecn congctl dctcp
| # ip route del 172.29.29.0/24 dev d0 features ecn congctl dctcp
| RTNETLINK answers: No such process
During route insertion, fib_convert_metrics() detects that the given CC
algo requires ECN and hence sets DST_FEATURE_ECN_CA bit in
RTAX_FEATURES.
During route deletion though, fib_metrics_match() compares stored
RTAX_FEATURES value with that from userspace (which obviously has no
knowledge about DST_FEATURE_ECN_CA) and fails.
Fixes: 5f9ae3d9e7e4a ("ipv4: do metrics match when looking up and deleting a route")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RSS table is 4k for T6 and later cards, add check for the
same.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First, the check of &q->ring.queue against NULL is wrong, it
is always false. We should check the value rather than the address.
Secondly, we need the same check in pfifo_fast_reset() too,
as both ->reset() and ->destroy() are called in qdisc_destroy().
Fixes: c5ad119fb6c0 ("net: sched: pfifo_fast use skb_array")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When, during a join operation, or during message transmission, a group
member needs to be added to the group's 'congested' list, we sort it
into the list in ascending order, according to its current advertised
window size. However, we miss the case when the member is already on
that list. This will have the result that the member, after the window
size has been decremented, might be at the wrong position in that list.
This again may have the effect that we during broadcast and multicast
transmissions miss the fact that a destination is not yet ready for
reception, and we end up sending anyway. From this point on, the
behavior during the remaining session is unpredictable, e.g., with
underflowing window sizes.
We now correct this bug by unconditionally removing the member from
the list before (re-)sorting it in.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In recent tests with new adapters, it was discovered that ARP
packets were not being properly processed. This patch adds
support for ARP packet headers to be passed to backing adapters,
if necessary.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Falcon says:
====================
ibmvnic: Fix and increase maximum TX/RX queues
This series renames IBMVNIC_MAX_TX_QUEUES to IBMVNIC_MAX_QUEUES since
it is used to allocate both RX and TX queues. The value is also increased
to accommodate newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase the number of queues allocated to accommodate recent
network adapter inclusions on the IBM vNIC platform.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This value denotes the maximum number of TX queues but is used
to allocate both RX and TX queues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For T6, tid start range should be read from
LE_DB_ACTIVE_TABLE_START_INDEX_A register.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-12-18
Here's the first bluetooth-next pull request for the 4.16 kernel.
- hci_ll: multiple cleanups & fixes
- Remove Gustavo Padovan from the MAINTAINERS file
- Support BLE Adversing while connected (if the controller can do it)
- DT updates for TI chips
- Various other smaller cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the boot loader to specify the MAC address in the device tree
to override the EEPROM, or in case no EEPROM is present.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Tristram Ha <tristram.ha@micrel.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
(client) gre6 <---> eth1 (route) eth2 <---> gre6 (server)
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions EMAC stop reception of incoming packets and
continuously increment R_MISS register instead of saving data into
provided buffer. The commit implement workaround for such situation.
Then the stall detected EMAC will be restarted.
On device the stall looks like the device lost it's dynamic IP address.
ifconfig shows that interface error counter rapidly increments.
At the same time on the DHCP server we can see continues DHCP-requests
from device.
In real network stalls happen really rarely. To make them frequent the
broadcast storm[1] should be simulated. For simulation it is necessary
to make following connections:
1. connect radxarock to 1st port of switch
2. connect some PC to 2nd port of switch
3. connect two other free ports together using standard ethernet cable,
in order to make a switching loop.
After that, is necessary to make a broadcast storm. For example, running on
PC 'ping' to some IP address triggers ARP-request storm. After some
time (~10sec), EMAC on rk3188 will stall.
Observed and tested on rk3188 radxarock.
[1] https://en.wikipedia.org/wiki/Broadcast_radiation
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few thousand such pages are usually left around due to the re-use of
L1 tables having been provided by the hypervisor (Dom0) or tool stack
(DomU). Set NX in the direct map variant, which needs to be done in L2
due to the dual use of the re-used L1s.
For x86_configure_nx() to actually do what it is supposed to do, call
get_cpu_cap() first. This was broken by commit 4763ed4d45 ("x86, mm:
Clean up and simplify NX enablement") when switching away from the
direct EFER read.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
This reverts commit 63dd00fa3e524c27cc0509190084ab147ecc8ae2.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e52 ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jonas Gorski says:
====================
bcm63xx_enet: remove mac_id usage
This patchset aims at reducing the platform device id number usage with
the target of making it eventually possible to probe the driver through OF.
Runtested on BCM6358.
Since the patches touch mostly net/, they should go through net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Directly use the platform device for generating the miibus name. This
removes the last user of bcm_enet_priv::mac_id and we can remove the
field.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling the ephy clock for mac 1 is harmless, and the actual usage of
the ephy is not restricted to mac 0, so we might as well remove the
check.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the reliance on device ids, pass the dma channel numbers to
the enet devices as platform data.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have the individual clocks available as "enet" we
don't need to rely on the device id for them anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Haishuang Yan says:
====================
net: speedup geneve/vxlan tunnels dismantle
This patch series add batching to vxlan/geneve tunnels so that netns
dismantles are less costly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in geneve_exit_net, it's better batch them
to speedup geneve tunnel dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we now hold RTNL lock in vxlan_exit_net, it's better to batch them
to speedup vxlan tunnels dismantle.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both first_tx_ctx and tx_skb are the head of tx ctx, it not
necessary to use two structure members to statically indicate
the head of tx ctx. So first_tx_ctx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
Introduce NETIF_F_GRO_HW
Introduce NETIF_F_GRO_HW feature flag and convert drivers that support
hardware GRO to use the new flag.
v5:
- Documentation changes requested by Alexander Duyck.
- bnx2x changes requested by Manish Chopra to enable LRO by default, and
disable GRO_HW if disable_tpa module parameter is set.
v4:
- more changes requested by Alexander Duyck:
- check GRO_HW/GRO dependency in drivers's ndo_fix_features().
- Reverse the order of RXCSUM and GRO_HW dependency check in
netdev_fix_features().
- No propagation in netdev_disable_gro_hw().
v3:
- Let driver's ndo_fix_features() disable NETIF_F_LRO when NETIF_F_GRO_HW
is set instead of doing it in common netdev_fix_features().
v2:
- NETIF_F_GRO_HW flag propagation between upper and lower devices not
required (see patch 1).
- NETIF_F_GRO_HW depends on NETIF_F_GRO and NETIF_F_RXCSUM.
- Add dev_disable_gro_hw() to disable GRO_HW for generic XDP.
- Use ndo_fix_features() on all 3 drivers to drop GRO_HW when it is not
supported
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and set edev->gro_disable according to the
feature flag. Add qede_fix_features() to drop NETIF_F_GRO_HW if
XDP is running or MTU does not support GRO_HW or GRO is not set.
qede_change_mtu() also checks and disables GRO_HW if MTU is not
supported.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW and turn on TPA_MODE_GRO when NETIF_F_GRO_HW
is set. Disable NETIF_F_GRO_HW in bnx2x_fix_features() if the MTU
does not support TPA_MODE_GRO or GRO is not set. bnx2x_change_mtu() also
needs to disable NETIF_F_GRO_HW if the MTU does not support it.
Original parameter disable_tpa will continue to disable LRO and GRO_HW.
Preserve the original behavior of enabling LRO by default. User has
to run ethtool -K to explicitly enable GRO_HW.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertise NETIF_F_GRO_HW in hw_features if hardware GRO is supported.
In bnxt_fix_features(), disable GRO_HW and LRO if current hardware
configuration does not allow it. GRO_HW depends on GRO. GRO_HW is
also mutually exclusive with LRO. XDP setup will now rely on
bnxt_fix_features() to turn off aggregation. During chip init, turn on
or off hardware GRO based on NETIF_F_GRO_HW in features flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware should not aggregate any packets when generic XDP is installed.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
