| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"Two fixes for the HID subsystem:
- regression fix for i2c-hid power management (Hans de Goede)
- signed vs unsigned API fix for Wacom driver (Jason Gerecke)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: wacom: generic: Treat serial number and related fields as unsigned
HID: i2c-hid: Send power-on command after reset
|
|
Rahul Lakkireddy says:
====================
cxgb4: add support for TC-MQPRIO Qdisc Offload
This series of patches add support for offloading TC-MQPRIO Qdisc
to Chelsio T5/T6 NICs. Offloading QoS traffic shaping and pacing
requires using Ethernet Offload (ETHOFLD) resources available on
Chelsio NICs. The ETHOFLD resources are configured by firmware
and taken from the resource pool shared with other Chelsio Upper
Layer Drivers. Traffic flowing through ETHOFLD region requires a
software netdev Tx queue (EOSW_TXQ) exposed to networking stack,
and an underlying hardware Tx queue (EOHW_TXQ) used for sending
packets through hardware.
ETHOFLD region is addressed using EOTIDs, which are per-connection
resource. Hence, EOTIDs are capable of storing only a very small
number of packets in flight. To allow more connections to share
the the QoS rate limiting configuration, multiple EOTIDs must be
allocated to reduce packet drops. EOTIDs are 1-to-1 mapped with
software EOSW_TXQ. Several software EOSW_TXQs can post packets to
a single hardware EOHW_TXQ.
The series is broken down as follows:
Patch 1 queries firmware for maximum available traffic classes,
as well as, start and maximum available indices (EOTID) into ETHOFLD
region, supported by the underlying device.
Patch 2 reworks queue configuration and simplifies MSI-X allocation
logic in preparation for ETHOFLD queues support.
Patch 3 adds skeleton for validating and configuring TC-MQPRIO Qdisc
offload. Also, adds support for software EOSW_TXQs and exposes them
to network stack. Updates Tx queue selection to use fallback NIC Tx
path for unsupported traffic that can't go through ETHOFLD queues.
Patch 4 adds support for managing hardware queues to rate limit
traffic flowing through them. The queues are allocated/removed based
on enabling/disabling TC-MQPRIO Qdisc offload, respectively.
Patch 5 adds Tx path for traffic flowing through software EOSW_TXQ
and EOHW_TXQ. Also, adds Rx path to handle Tx completions.
Patch 6 updates exisiting SCHED API to configure FLOWC based QoS
offload. In the existing QUEUE based rate limiting, multiple queues
sharing a traffic class get the aggreagated max rate limit value.
On the other hand, in FLOWC based rate limiting, multiple queues
sharing a traffic class get their own individual max rate limit
value. For example, if 2 queues are bound to class 0, which is rate
limited to 1 Gbps, then in QUEUE based rate limiting, both the
queues get the aggregate max output of 1 Gbps only. In FLOWC based
rate limiting, each queue gets its own output of max 1 Gbps each;
i.e. 2 queues * 1 Gbps rate limit = 2 Gbps max output.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rework SCHED API to allow offloading TC-MQPRIO QoS configuration.
The existing QUEUE based rate limiting throttles all queues sharing
a traffic class, to the specified max rate limit value. So, if
multiple queues share a traffic class, then all the queues get
the aggregate specified max rate limit.
So, introduce the new FLOWC based rate limiting, where multiple
queues can share a traffic class with each queue getting its own
individual specified max rate limit.
For example, if 2 queues are bound to class 0, which is rate limited
to 1 Gbps, then 2 queues using QUEUE based rate limiting, get the
aggregate output of 1 Gbps only. In FLOWC based rate limiting, each
queue gets its own output of max 1 Gbps each; i.e. 2 queues * 1 Gbps
rate limit = 2 Gbps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement Tx path for traffic flowing through software EOSW_TXQ
and EOHW_TXQ. Since multiple EOSW_TXQ can post packets to a single
EOHW_TXQ, protect the hardware queue with necessary spinlock. Also,
move common code used to generate TSO work request to a common
function.
Implement Rx path to handle Tx completions for successfully
transmitted packets.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring and managing ETHOFLD hardware queues.
Keep the queue count and MSI-X allocation scheme same as NIC queues.
ETHOFLD hardware queues are dynamically allocated/destroyed as
TC-MQPRIO Qdisc offload is enabled/disabled on the corresponding
interface, respectively.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add logic for validation and configuration of TC-MQPRIO Qdisc
offload. Also, add support to manage EOSW_TXQ, which have 1-to-1
mapping with EOTIDs, and expose them to network stack.
Move common skb validation in Tx path to a separate function and
add minimal Tx path for ETHOFLD. Update Tx queue selection to return
normal NIC Txq to send traffic pattern that can't go through ETHOFLD
Tx path.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify queue configuration and MSI-X allocation logic. Use a single
MSI-X information table for both NIC and ULDs. Remove hard-coded
MSI-X indices for firmware event queue and non data interrupts.
Instead, use the MSI-X bitmap to obtain a free MSI-X index
dynamically. Save each Rxq's index into the MSI-X information table,
within the Rxq structures themselves, for easier cleanup.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QoS offload needs Ethernet Offload (ETHOFLD) resources present in the
NIC. These resources are shared with other ULDs. So, query firmware
for the available number of traffic classes, as well as, start and
end indices (EOTID) of the ETHOFLD region.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If someone requests fscache on the mount, and the kernel doesn't
support it, it should fail the mount.
[ Drop ceph prefix -- it's provided by pr_err. ]
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.4
These are a collection of fixes since v5.4-rc4 that have accumilated,
they're all driver specific and there's nothing major in here so it's
probably not essential to actually send them but I'll leave that call to
you.
|
|
I forgot to change last_packets field in struct net_rate_estimator.
Without this fix, rate estimators would misbehave after more
than 2^32 packets have been sent.
Another solution would be to be careful and only use the
32 least significant bits of packets counters, but we have
a hole in net_rate_estimator structure and this looks
easier to read/maintain.
Fixes: d0083d98f685 ("net_sched: extend packet counter to 64bit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1
Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-06
This series contains updates to ice driver only.
Scott adds ethtool -m support so that we can read eeprom data on SFP/OSFP
modules.
Anirudh updates the return value to properly reflect when SRIOV is not
supported.
Md Fahad updates the driver to handle a change in the NVM, where the
boot configuration section was moved to the Preserved Field Area (PFA)
of the NVM.
Paul resolves an issue when DCBx requests non-contiguous TCs, transmit
hangs could occur, so configure a default traffic class (TC0) in these
cases to prevent traffic hangs. Adds a print statement to notify the
user when unsupported modules are inserted.
Bruce fixes up the driver unload code flow to ensure we do not clear the
interrupt scheme until the reset is complete, otherwise a hardware error
may occur.
Dave updates the DCB initialization to set is_sw_lldp boolean when the
firmware has been detected to be in an untenable state. This will
ensure that the firmware is in a known state.
Michal saves off the PCI state and I/O BARs address after PCI bus reset
so that after the reset, device registers can be read. Also adds a NULL
pointer check to prevent a potential kernel panic.
Mitch resolves an issue where VF's on PF's other than 0 were not seeing
resets by using the per-PF VF ID instead of the absolute VF ID.
Krzysztof does some code cleanup to remove a unneeded wrapper and
reduces the code complexity.
Brett reduces confusion by changing the name of ice_vc_dis_vf() to
ice_vc_reset_vf() to better describe what the function is actually
doing.
v2: dropped patch 3 "ice: Add support for FW recovery mode detection"
from the origin al series, while Ani makes changes based on
community feedback to implement devlink into the changes.
v3: dropped patch 1 "ice: implement set_eeprom functionality" due to a
bug found and additional changes will be needed when Ani implements
devlink in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.
Fixes: c5f299d59261 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Walle says:
====================
net: phy: at803x device tree binding
Adds a device tree binding to configure the clock and the RGMII voltage.
Changes since v1:
- rebased to latest net-next
- renamed "Atheros" to "Qualcomm Atheros"
- add a new patch to remove config_init() from AR9331
Changes since the RFC:
- renamed the Kconfig entry to "Qualcomm Atheros.." and reordered the
item
- renamed the prefix from atheros to qca
- use the correct name AR803x (instead of AT803x) in new files and
dt-bindings.
- listed the PHY maintainers in the new schema. Hopefully, thats ok.
- fixed a typo in the bindings schema
- run dtb_checks and dt_binding_check and fixed the schema
- dropped the rgmii-io-1v8 property; instead provide two regulators vddh
and vddio, add one consumer vddio-supply
- fix the clock settings for the AR8030/AR8035
- only the AR8031 supports chaning the LDO and the PLL mode in software.
Check if we have the correct PHY.
- new patch to mention the AR8033 which is the same as the AR8031 just
without PTP support
- new patch which corrects any displayed PHY names and comments. Be
consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to its datasheet, the internal PHY doesn't have debug
registers nor MMDs. Since config_init() only configures delays and
clocks and so on in these registers it won't be needed on this PHY.
Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix at least the displayed strings. The actual name of the chip is
AR803x.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AR8033 is the AR8031 without PTP support. All other registers are
the same. Unfortunately, they share the same PHY ID. Therefore, we
cannot distinguish between the one with PTP support and the one without.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document the Atheros AR803x PHY bindings.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The name of the PHY is actually AR803x not AT803x. Additionally, add the
name of the vendor and mention the AR8031 support.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahamees says:
====================
Mellanox, mlx5 fixes 2019-11-06
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
No -stable this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reading tp->recvmsg_inq after socket lock is released
raises a KCSAN warning [1]
Replace has_tss & has_cmsg by cmsg_flags and make
sure to not read tp->recvmsg_inq a second time.
[1]
BUG: KCSAN: data-race in tcp_chrono_stop / tcp_recvmsg
write to 0xffff888126adef24 of 2 bytes by interrupt on cpu 0:
tcp_chrono_set net/ipv4/tcp_output.c:2309 [inline]
tcp_chrono_stop+0x14c/0x280 net/ipv4/tcp_output.c:2338
tcp_clean_rtx_queue net/ipv4/tcp_input.c:3165 [inline]
tcp_ack+0x274f/0x3170 net/ipv4/tcp_input.c:3688
tcp_rcv_established+0x37e/0xf50 net/ipv4/tcp_input.c:5696
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1561
tcp_v4_rcv+0x19dc/0x1bb0 net/ipv4/tcp_ipv4.c:1942
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5214
napi_skb_finish net/core/dev.c:5677 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5710
read to 0xffff888126adef25 of 1 bytes by task 7275 on cpu 1:
tcp_recvmsg+0x77b/0x1a30 net/ipv4/tcp.c:2187
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7275 Comm: sshd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: b75eba76d3d7 ("tcp: send in-queue bytes in cmsg upon read")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_backlog.tail might be read without holding the socket spinlock,
we need to add proper READ_ONCE()/WRITE_ONCE() to silence the warnings.
KCSAN reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff8881265109f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:907 [inline]
sk_add_backlog include/net/sock.h:938 [inline]
tcp_add_backlog+0x476/0xce0 net/ipv4/tcp_ipv4.c:1759
tcp_v4_rcv+0x1a70/0x1bd0 net/ipv4/tcp_ipv4.c:1947
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:4929
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5043
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5133
napi_skb_finish net/core/dev.c:5596 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5629
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6311 [inline]
net_rx_action+0x3ae/0xa90 net/core/dev.c:6379
__do_softirq+0x115/0x33f kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0xbb/0xe0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
do_IRQ+0xa6/0x180 arch/x86/kernel/irq.c:263
ret_from_intr+0x0/0x19
native_safe_halt+0xe/0x10 arch/x86/kernel/paravirt.c:71
arch_cpu_idle+0x1f/0x30 arch/x86/kernel/process.c:571
default_idle_call+0x1e/0x40 kernel/sched/idle.c:94
cpuidle_idle_call kernel/sched/idle.c:154 [inline]
do_idle+0x1af/0x280 kernel/sched/idle.c:263
cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:355
start_secondary+0x208/0x260 arch/x86/kernel/smpboot.c:264
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241
read to 0xffff8881265109f8 of 8 bytes by task 8057 on cpu 0:
tcp_recvmsg+0x46e/0x1b40 net/ipv4/tcp.c:2050
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8057 Comm: syz-fuzzer Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.
Fixes: 0c65b2b90d13 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 69c51582ff786 ("dpif-netlink: don't allocate per
thread netlink sockets"), in Open vSwitch ovs-vswitchd, has
changed the number of allocated sockets to just one per port
by moving the socket array from a per handler structure to
a per datapath one. In the kernel datapath, a vport will have
only one socket in most case, if so select it directly in
fast-path.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb64c ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jose Abreu says:
====================
net: stmmac: Fixes for -net
Misc fixes for stmmac.
Patch 1/11 and 2/11, use the correct variable type for bitrev32() calls.
Patch 3/11, fixes the random failures the we were seing when running selftests.
Patch 4/11, prevents a crash that can occur when receiving AVB packets and with
SPH feature enabled on XGMAC.
Patch 5/11, fixes the correct settings for CBS on XGMAC.
Patch 6/11, corrects the interpretation of AVB feature on XGMAC.
Patch 7/11, disables Flow Control for AVB enabled queues on XGMAC.
Patch 8/11, disables MMC interrupts on XGMAC, preventing a storm of interrupts.
Patch 9/11, fixes the number of packets that were being taken into account in
the RX path cleaning function.
Patch 10/11, fixes an incorrect descriptor setting that could cause IP
misbehavior.
Patch 11/11, fixes the IOC generation mechanism when multiple descriptors
are used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.
Fixes: b6cdf09f51c2 ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.
Fixes: c2b69474d63b ("net: stmmac: xgmac: Correct RAVSEL field interpretation")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.
To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 0efedbf11f07 ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function ptp_clock_register() returns ERR_PTR() and never returns
NULL. The NULL test should be removed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing unlock before return from function idtcm_probe()
in the error handling case.
Fixes: 3a6ba7dc7799 ("ptp: Add a ptp clock driver for IDT ClockMatrix.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing register size validation in bitwise and cmp offloads.
2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
from Dan Carpenter.
3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
Stefano Brivio.
4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
from Jozsef Kadlecsik.
5) Fix unaligned access to private data area of nf_tables instructions,
from Lukas Wunner.
6) Relax check for object updates, reported as a regression by
Eric Garver, patch from Fernando Fernandez Mancera.
7) Crash on ebtables dnat extension when used from the output path.
From Florian Westphal.
8) Fix bogus EOPNOTSUPP when updating basechain flags.
9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When preparing tunnel packets for the link failover or synchronization,
as for the safe algorithm, we added a dummy packet on the pair link but
never sent it out. In the case of failover, the pair link will be reset
anyway. But for link synching, it will always result in retransmission
of the dummy packet after that.
We have also observed that such the retransmission at the early stage
when a new node comes in a large cluster will take some time and hard
to be done, leading to the repeated retransmit failures and the link is
reset.
Since in commit 4929a932be33 ("tipc: optimize link synching mechanism")
we have already built a dummy 'TUNNEL_PROTOCOL' message on the new link
for the synchronization, there's no need for the dummy on the pair one,
this commit will skip it when the new mechanism takes in place. In case
nothing exists in the pair link's transmq, the link synching will just
start and stop shortly on the peer side.
The patch is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
lwtunnel: add ip and ip6 options setting and dumping
With this patchset, users can configure options by ip route encap
for geneve, vxlan and ersapn lwtunnel, like:
# ip r a 1.1.1.0/24 encap ip id 1 geneve class 0 type 0 \
data "1212121234567890" dst 10.1.0.2 dev geneve1
# ip r a 1.1.1.0/24 encap ip id 1 vxlan gbp 456 \
dst 10.1.0.2 dev erspan1
# ip r a 1.1.1.0/24 encap ip id 1 erspan ver 1 idx 123 \
dst 10.1.0.2 dev erspan1
iproute side patch is attached on the reply of this mail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_erspan() for .build_state and
ip_tun_fill_encap_opts_erspan() for .fill_encap and
if (tun_flags & TUNNEL_ERSPAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_vxlan() for .build_state and
ip_tun_fill_encap_opts_vxlan() for .fill_encap and
if (tun_flags & TUNNEL_VXLAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To add options setting and dumping, .build_state(), .fill_encap() and
.get_encap_size() in ip_tun_lwt_ops needs to be extended:
ip_tun_build_state():
ip_tun_parse_opts():
ip_tun_parse_opts_geneve()
ip_tun_fill_encap_info():
ip_tun_fill_encap_opts():
ip_tun_fill_encap_opts_geneve()
ip_tun_encap_nlsize()
ip_tun_opts_nlsize():
if (tun_flags & TUNNEL_GENEVE_OPT)
ip_tun_parse_opts(), ip_tun_fill_encap_opts() and ip_tun_opts_nlsize()
processes LWTUNNEL_IP_OPTS.
ip_tun_parse_opts_geneve(), ip_tun_fill_encap_opts_geneve() and
if (tun_flags & TUNNEL_GENEVE_OPT) processes LWTUNNEL_IP_OPTS_GENEVE.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
