| Age | Commit message (Collapse) | Author |
|---|
|
Add a property to the binding to configure the Alert Polarity.
Alert pin is asserted based on the value of Alert Polarity bit of
Mask/Enable register. It is by default 0 which means Alert pin is
configured to be active low open collector. Value of 1 maps to
Inverted (active high open collector).
Signed-off-by: Amna Waseem <Amna.Waseem@axis.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240603-apol-ina2xx-fix-v3-1-b9eff3158e4e@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit ac0c26bae662 ("hwmon: (lm25066) Use i2c_get_match_data()") changed
enum chips to start with 1 instead of 0, under the assumption that
the data pointer in of_device_id must not start with 0 (NULL) if
i2c_get_match_data() is used. However, that is perfectly fine as long as
there is also an i2c_device_id array with the same data which is used
as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 10a0575ea09d ("hwmon: (nct6775-i2c) Use i2c_get_match_data()")
introduced calling i2c_get_match_data() to the nct6775 driver. As part
of that commit, enum kinds was changed to start with 1, based on
Adjust the 'kinds' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
The patch had to be fixed later with commit 2792fc8f8c83 ("hwmon:
(nct6775-core) Explicitly initialize nct6775_device_names indexes") and
commit efe86092ab31 ("hwmon: (nct6775-platform) Explicitly initialize
nct6775_sio_names indexes").
Various patches submitted later show that the change from 0 to 1 is
not really necessary. As it turns out, it is perfectly fine as long as
there is an i2c_device_id array with the same data as in the of_device_id
array. This data is used as fallback if the data pointer in struct
of_device_id is NULL (0).
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Earlier it was assumed that the data pointer in of_device_id must not start
with 0 (NULL) if i2c_get_match_data() is used. However, it turns out that
this is perfectly fine as long as there is also an i2c_device_id array with
the same data, which is used as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
While doing that, remove chip_id from struct mp2856_data since it is only
used in the probe function, and typecast the result of i2c_get_match_data()
to kernel_ulong_t to avoid the double typecast.
Cc: Peter Yin <peteryin.openbmc@gmail.com>
Cc: Potin Lai <potin.lai.pt@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If a driver calls device_get_match_data(), the .data pointer in its id
data structures must not be NULL/0 because device_get_match_data()
returns NULL if an entry is not found. Explain that in a comment to avoid
confusion why this is required in this driver but not in other drivers.
Cc: Daniel Matyas <daniel.matyas@analog.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Provided and tested by a user in a GitHub PR [1].
[1] https://github.com/zeule/asus-ec-sensors/pull/56
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20240608085146.572777-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
With SPD5118 chip detection for the most part handled by the i2c-smbus
core using DMI information, the spd5118 driver no longer needs to
auto-detect spd5118 compliant chips.
Auto-detection by the driver is still needed on systems with no DMI support
or on systems with more than eight DIMMs and can not be removed entirely.
However, it affects boot time and introduces the risk of mis-identifying
chips. Add configuration option to be able to disable it on systems where
chip detection is handled outside the driver.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Detect (LP)DDR5 memory and instantiate the SPD5118 driver automatically.
Suggested-by: Thomas Weißschuh <linux@weissschuh.net>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for reading SPD NVMEM data from SPD5118 (Jedec JESD300)
compliant memory modules. NVMEM write operation is not supported.
NVMEM support is optional. If CONFIG_NVMEM is disabled, the driver will
still instantiate but not provide NVMEM attribute files.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add suspend/resume support to ensure that limit and configuration
registers are updated and synchronized after a suspend/resume cycle.
Cc: Armin Wolf <W_Armin@gmx.de>
Cc: Stephen Horvath <s.horvath@outlook.com.au>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add bindings for the SPD hub present in DDR5 modules.
(https://www.jedec.org/standards-documents/docs/jesd300-5b01).
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/asus_atk0110.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/corsair-cpro.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/mr75203.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-hwmon-v1-1-1ea6d6fe61e3@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Switch to the _scoped() version introduced in commit 365130fd47af
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240404-hwmon_device_for_each_child_node_scoped-v1-2-53997abde43c@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Switch to the _scoped() version introduced in commit 365130fd47af
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240404-hwmon_device_for_each_child_node_scoped-v1-1-53997abde43c@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-32-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-31-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-30-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-29-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-28-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-27-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-26-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-25-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-24-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-23-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-22-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-21-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-20-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-19-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-18-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-17-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-16-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-15-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-14-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-13-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-12-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-11-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-10-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-9-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-8-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-7-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-6-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-5-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-4-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-3-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-2-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use spi_get_device_match_data() helper to simplify a bit the driver.
Also kernel_ulong_t type is preferred for kernel code over uintptr_t
(needed for the cast).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240606142515.132504-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for g761 PWM Fan Controller.
The g761 is a copy of the g763 with the only difference of supporting
and internal clock. The internal clock is used if no clocks property is
defined in device node and in such case the required bit is enabled and
clock handling is skipped.
The internal clock oscillator runs at 31KHz.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20240604164348.542-3-ansuelsmth@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for g761 PWM Fan controller. This is an exact copy of g763
with the difference that it does also support an internal clock
oscillator.
With clocks property not defined, the internal clock oscillator is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240604164348.542-2-ansuelsmth@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert g762 Documentation to yaml schema and port all the custom
properties and info.
Add the vendor prefix to name to follow naming standard.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240604164348.542-1-ansuelsmth@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
