Age | Commit message (Collapse) | Author |
|
DMA ch status register offset change in acp7.0 platform
Incorrect DMA channel status register offset check lead to
firmware boot failure.
[ 14.432497] snd_sof_amd_acp70 0000:c4:00.5: ------------[ DSP dump start ]------------
[ 14.432533] snd_sof_amd_acp70 0000:c4:00.5: Firmware boot failure due to timeout
[ 14.432549] snd_sof_amd_acp70 0000:c4:00.5: fw_state: SOF_FW_BOOT_IN_PROGRESS (3)
[ 14.432610] snd_sof_amd_acp70 0000:c4:00.5: invalid header size 0x71c41000. FW oops is bogus
[ 14.432626] snd_sof_amd_acp70 0000:c4:00.5: unexpected fault 0x71c40000 trace 0x71c40000
[ 14.432642] snd_sof_amd_acp70 0000:c4:00.5: ------------[ DSP dump end ]------------
[ 14.432657] snd_sof_amd_acp70 0000:c4:00.5: error: failed to boot DSP firmware -5
[ 14.432672] snd_sof_amd_acp70 0000:c4:00.5: fw_state change: 3 -> 4
[ 14.433260] dmic-codec dmic-codec: ASoC: Unregistered DAI 'dmic-hifi'
[ 14.433319] snd_sof_amd_acp70 0000:c4:00.5: fw_state change: 4 -> 0
[ 14.433358] snd_sof_amd_acp70 0000:c4:00.5: error: sof_probe_work failed err: -5
Update correct register offset for DMA ch status register.
Fixes: 490be7ba2a01 ("ASoC: SOF: amd: add support for acp7.0 based platform")
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20241106142658.1240929-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Xiaomi Book Pro 14 2022 (MIA2210-AD) requires a quirk entry for its
internal microphone to be enabled.
This is likely due to similar reasons as seen previously on Redmi Book
14/15 Pro 2022 models (since they likely came with similar firmware):
- commit dcff8b7ca92d ("ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022
into DMI table")
- commit c1dd6bf61997 ("ASoC: amd: yc: Add Xiaomi Redmi Book Pro 14 2022
into DMI table")
A quirk would likely be needed for Xiaomi Book Pro 15 2022 models, too.
However, I do not have such device on hand so I will leave it for now.
Signed-off-by: Mingcong Bai <jeffbai@aosc.io>
Link: https://patch.msgid.link/20241106024052.15748-1-jeffbai@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case of error when requesting ctrl_chan DMA channel, ctrl_chan is not
null. So the release of the dma channel leads to the following issue:
[ 4.879000] st,stm32-spdifrx 500d0000.audio-controller:
dma_request_slave_channel error -19
[ 4.888975] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000003d
[...]
[ 5.096577] Call trace:
[ 5.099099] dma_release_channel+0x24/0x100
[ 5.103235] stm32_spdifrx_remove+0x24/0x60 [snd_soc_stm32_spdifrx]
[ 5.109494] stm32_spdifrx_probe+0x320/0x4c4 [snd_soc_stm32_spdifrx]
To avoid this issue, release channel only if the pointer is valid.
Fixes: 794df9448edb ("ASoC: stm32: spdifrx: manage rebind issue")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20241105140242.527279-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ALSA SoC Sound has Generic Sound Card (Simple-Card, Audio-Graph-Card,
Audio-Graph-Card2). Adds its Maintainer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/87ikt2a41c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add new driver version to support tas2563 & tas2781 qfn chip
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20241104100055.48-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Alexey Klimov <alexey.klimov@linaro.org>:
This sent as RFC because of the following:
- regarding the LO switch patch. I've got info about that from two persons
independently hence not sure what tags to put there and who should be
the author. Please let me know if that needs to be corrected.
- the wcd937x pdm watchdog is a problem for audio playback and needs to be
fixed. The minimal fix would be to at least increase timeout value but
it will still trigger in case of plenty of dbg messages or other
delay-generating things. Unfortunately, I can't test HPHL/R outputs hence
the patch is only for AUX. The other options would be introducing
module parameter for debugging and using HOLD_OFF bit for that or
adding Kconfig option.
Alexey Klimov (2):
ASoC: codecs: wcd937x: add missing LO Switch control
ASoC: codecs: wcd937x: relax the AUX PDM watchdog
sound/soc/codecs/wcd937x.c | 12 ++++++++++--
sound/soc/codecs/wcd937x.h | 4 ++++
2 files changed, 14 insertions(+), 2 deletions(-)
--
2.45.2
|
|
On a system with wcd937x, rxmacro and Qualcomm audio DSP, which is pretty
common set of devices on Qualcomm platforms, and due to the order of how
DAPM widgets are powered on (they are sorted), there is a small time window
when wcd937x chip is online and expects the flow of incoming data but
rxmacro is not yet online. When wcd937x is programmed to receive data
via AUX port then its AUX PDM watchdog is enabled in
wcd937x_codec_enable_aux_pa(). If due to some reasons the rxmacro and
soundwire machinery are delayed to start streaming data, then there is
a chance for this AUX PDM watchdog to reset the wcd937x codec. Such event
is not logged as a message and only wcd937x IRQ counter is increased
however there could be a lot of other reasons for that IRQ.
There is a similar opportunity for such delay during DAPM widgets power
down sequence.
If wcd937x codec reset happens on the start of the playback, then there
will be no sound and if such reset happens at the end of a playback then
it may generate additional clicks and pops noises.
On qrb4210 RB2 board without any debugging bits the wcd937x resets are
sometimes observed at the end of a playback though not always.
With some debugging messages or with some tracing enabled the AUX PDM
watchdog resets the wcd937x codec at the start of a playback and there
is no sound output at all.
In this patch:
- TIMEOUT_SEL bit in PDM_WD_CTL2 register is set to increase the watchdog
reset delay to 100ms which eliminates the AUX PDM watchdog IRQs on
qrb4210 RB2 board completely and decreases the number of unwanted clicks
noises;
- HOLD_OFF bit postpones triggering such watchdog IRQ till wcd937x codec
reset which usually happens at the end of a playback. This allows to
actually output some sound in case of debugging.
Cc: Adam Skladowski <a39.skl@gmail.com>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The wcd937x supports also AUX input but the control that sets correct
soundwire port for this is missing. This control is required for audio
playback, for instance, on qrb4210 RB2 board as well as on other
SoCs.
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Reported-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Suggested-by: Adam Skladowski <a39.skl@gmail.com>
Suggested-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix DTB warnings when rk3308-codec used with audio-graph-card by
documenting port property:
codec@ff560000: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20241028213314.476776-2-dmt.yashin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The widgets array in the snd_soc_dapm_widget_list has a __counted_by
attribute attached to it, which points to the num_widgets variable. This
attribute is used in bounds checking, and if it is not set before the
array is filled, then the bounds sanitizer will issue a warning or a
kernel panic if CONFIG_UBSAN_TRAP is set.
This patch sets the size of the widgets list calculated with
list_for_each as the initial value for num_widgets as it is used for
allocating memory for the array. It is updated with the actual number of
added elements after the array is filled.
Signed-off-by: Aleksei Vetrov <vvvvvv@google.com>
Fixes: 80e698e2df5b ("ASoC: soc-dapm: Annotate struct snd_soc_dapm_widget_list with __counted_by")
Link: https://patch.msgid.link/20241028-soc-dapm-bounds-checker-fix-v1-1-262b0394e89e@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the new "LPE0F28" code path using the uninitialized ctx variable
to log an error.
Fixes: 6668610b4d8c ("ASoC: Intel: sst: Support LPE0F28 ACPI HID")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410261106.EBx49ssy-lkp@intel.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241026143615.171821-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If devm_gpiod_get_optional() fails, we need to disable previously enabled
regulators, as done in the other error handling path of the function.
Also, gpiod_set_value_cansleep(, 1) needs to be called to undo a
potential gpiod_set_value_cansleep(, 0).
If the "reset" gpio is not defined, this additional call is just a no-op.
This behavior is the same as the one already in the .remove() function.
Fixes: 11b9cd748e31 ("ASoC: cs42l51: add reset management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/a5e5f4b9fb03f46abd2c93ed94b5c395972ce0d1.1729975570.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some old Bay Trail tablets which shipped with Android as factory OS
have the SST/LPE audio engine described by an ACPI device with a
HID (Hardware-ID) of LPE0F28 instead of 80860F28.
Add support for this. Note this uses a new sst_res_info for just
the LPE0F28 case because it has a different layout for the IO-mem ACPI
resources then the 80860F28.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241025090221.52198-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Vexia Edu Atla 10 tablet mostly uses the BYTCR tablet defaults,
but as happens on more models it is using IN1 instead of IN3 for
its internal mic and JD_SRC_JD2_IN4N instead of JD_SRC_JD1_IN4P
for jack-detection.
Add a DMI quirk for this to fix the internal-mic and jack-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On some x86 Bay Trail tablets which shipped with Android as factory OS,
the DSDT is so broken that the codec needs to be manually instantatiated
by the special x86-android-tablets.ko "fixup" driver for cases like this.
This means that the codec-dev cannot be retrieved through its ACPI fwnode,
add support to the bytcr_rt5640 machine driver for such manually
instantiated rt5640 i2c_clients.
An example of a tablet which needs this is the Vexia EDU ATLA 10 tablet,
which has been distributed to schools in the Spanish Andalucía region.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024211615.79518-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Disable IRQs from rt5640_cancel_work(), this fixes a crash caused by
the IRQ never getting freed when the driver is unbound from the i2c_client
with jack-detection active:
[ 193.138780] rt5640 i2c-rt5640: ASoC: unknown pin LDO2
[ 193.138830] rt5640 i2c-rt5640: ASoC: unknown pin MICBIAS1
[ 193.671218] BUG: kernel NULL pointer dereference, address: 0000000000000078
[ 193.671239] #PF: supervisor read access in kernel mode
[ 193.671248] #PF: error_code(0x0000) - not-present page
...
[ 193.671531] ? asm_exc_page_fault+0x22/0x30
[ 193.671551] ? rt5640_jack_inserted+0x10/0x80 [snd_soc_rt5640]
[ 193.671574] rt5640_detect_headset+0x93/0x130 [snd_soc_rt5640]
[ 193.671596] rt5640_jack_work+0x93/0x355 [snd_soc_rt5640]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024215612.92147-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 15c7fab0e047 ("ASoC: qcom: Move Soundwire runtime stream alloc to
soundcards") moved the allocation of Soundwire stream runtime from the
Qualcomm Soundwire driver to each individual machine sound card driver,
except that it forgot to update SC7280 card.
Just like for other Qualcomm sound cards using Soundwire, the card
driver should allocate and release the runtime. Otherwise sound
playback will result in a NULL pointer dereference or other effect of
uninitialized memory accesses (which was confirmed on SDM845 having
similar issue).
Cc: stable@vger.kernel.org
Cc: Alexey Klimov <alexey.klimov@linaro.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 15c7fab0e047 ("ASoC: qcom: Move Soundwire runtime stream alloc to soundcards")
Link: https://lore.kernel.org/r/20241010054109.16938-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241012101108.129476-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On some platforms, for example i.MX93, there is only one
audio PLL source, so some sample rate can't be supported.
If the PLL source is used for 8kHz series rates, then 11kHz
series rates can't be supported.
So add constraints according to the frequency of available
clock sources, then alsa-lib will help to convert the
unsupported rate for the driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1728884313-6778-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
clk_stop_timeout should be increased to 900ms to fix clock stop issue.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://patch.msgid.link/cd26275d9fc54374a18dc016755cb72d@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Clean up the link DMA for playback during stop for IPC4 is required to
reset the DMA read/write pointers when the stream is prepared and
restarted after a call to snd_pcm_drain()/snd_pcm_drop().
The change is mainly on ASoC. We may go via ASoC tree with Vinod's
Acked-by tag
Ranjani Sridharan (4):
ASoC: SOF: ipc4-topology: Do not set ALH node_id for aggregated DAIs
ASoC: SOF: Intel: hda: Handle prepare without close for non-HDA DAI's
soundwire: intel_ace2x: Send PDI stream number during prepare
ASoC: SOF: Intel: hda: Always clean up link DMA during stop
drivers/soundwire/intel_ace2x.c | 19 +++++-----------
sound/soc/sof/intel/hda-dai-ops.c | 23 +++++++++----------
sound/soc/sof/intel/hda-dai.c | 37 +++++++++++++++++++++++++++----
sound/soc/sof/ipc4-topology.c | 15 +++++++++++--
4 files changed, 62 insertions(+), 32 deletions(-)
--
2.43.0
|
|
On i.MX8MM the register of volume control has positive and negative
values. It is different from other platforms like i.MX8MP and i.MX93
which only have positive values. Add a volume_sx flag to use SX_TLV
volume control for this kind of platform. Use common TLV volume control
for other platforms.
Fixes: cdfa92eb90f5 ("ASoC: fsl_micfil: Correct the number of steps on SX controls")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://patch.msgid.link/20241017071507.2577786-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Turns out some registers of pre-2.5 version of rxmacro codecs are not
located at the expected offsets but 0xc further away in memory. So far
the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and
CDC_RX_RX2_RX_PATH_DSM_CTL.
CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address
0x540 for RX2 but it should be 0x54C and it also overwrites
CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540.
The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n).
Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version
and above this offset will be equal to 0.
With such change the corresponding RXn() macros will generate the same
values for 2.5 codec version for all RX paths and the same old values
for pre-2.5 version for RX0 and RX1. However for the latter case with
RX2 path it will also add rxn_reg_stride2 on top.
While at this, also remove specific if-check for INTERP_AUX from
rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check
was used to handle such special offset for AUX interpolator but since
CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n)
macros will generate the correst addresses of dsm register, they are no
longer needed.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20241016221049.1145101-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change my contact e-mail in pcm3060 driver and MAINTAINERS
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: Kirill Marinushkin <kmarinushkin@birdec.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-sound@vger.kernel.org
Link: https://patch.msgid.link/20241016215810.1544222-1-k.marinushkin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a new match table entry on Lunarlake for the TM2 laptops
with rt713 and rt1318.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20241016030703.13669-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASUS Vivobook E1404FA needs a quirks-table entry for the internal microphone to function properly.
Signed-off-by: Ilya Dudikov <ilyadud@mail.ru>
Link: https://patch.msgid.link/20241016034038.13481-1-ilyadud25@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is required to reset the DMA read/write pointers when the stream is
prepared and restarted after a call to snd_pcm_drain()/snd_pcm_drop().
Also, now that the stream is reset during stop, do not save LLP registers
in the case of STOP/suspend to avoid erroneous delay reporting.
Link: https://github.com/thesofproject/sof/issues/9502
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the case of a prepare callback after an xrun or when the PCM is
restarted after a call to snd_pcm_drain/snd_pcm_drop, avoid
reprogramming the SHIM registers but send the PDI stream number so that
the link DMA data can be set. This is needed for the case that the DMA
data is cleared when the PCM is stopped and restarted without being
closed.
Link: https://github.com/thesofproject/sof/issues/9502
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When a PCM is restarted after a snd_pcm_drain/snd_pcm_drop(), the prepare
callback will be invoked and the hw_params will be set again. For the
HDA DAI's, the hw_params function handles this case already but not for
the non-HDA DAI's. So, add the check for link_prepared to verify if the
hw_params should be done again or not. Additionally, for SDW DAI's reset
the PCMSyCM registers as would be done in the case of a start after a
hw_free.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For aggregated DAIs, the node ID is set to the group_id during the DAI
widget's ipc_prepare op. With the current logic, setting the dai_index
for node_id in the dai_config is redundant as it will be overwritten
with the group_id anyway. Removing it will also prevent any accidental
clearing/resetting of the group_id for aggregated DAIs due to the
dai_config calls could that happen before the allocated group_id is
freed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
All: stable@vger.kernel.org # 6.10.x 6.11.x
Link: https://patch.msgid.link/20241016032910.14601-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To help Claudiu and offload the work, add myself to the maintainer list for
those drivers.
Acked-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://patch.msgid.link/20241014092830.46709-1-andrei.simion@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SDM845 sound card driver uses qcom_snd_sdw_startup() from the common
Soundwire module, so select it to fix build failures:
ERROR: modpost: "qcom_snd_sdw_startup" [sound/soc/qcom/snd-soc-sdm845.ko] undefined!
Fixes: d0e806b0cc62 ("ASoC: qcom: sdm845: add missing soundwire runtime stream alloc")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241012100957.129103-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Irq handler need to be executed as fast as possible, so
the log in irq handler is better to use dev_dbg which needs
to be enabled when debugging.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://patch.msgid.link/1728622433-2873-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On the HiHope boards, we have a single port with a single endpoint defined
as below:
....
rsnd_port: port {
rsnd_endpoint: endpoint {
remote-endpoint = <&dw_hdmi0_snd_in>;
dai-format = "i2s";
bitclock-master = <&rsnd_endpoint>;
frame-master = <&rsnd_endpoint>;
playback = <&ssi2>;
};
};
....
With commit 547b02f74e4a ("ASoC: rsnd: enable multi Component support for
Audio Graph Card/Card2"), support for multiple ports was added. This caused
probe failures on HiHope boards, as the endpoint could not be retrieved due
to incorrect device node pointers being used.
This patch fixes the issue by updating the `rsnd_dai_of_node()` and
`rsnd_dai_probe()` functions to use the correct device node pointers based
on the port names ('port' or 'ports'). It ensures that the endpoint is
properly parsed for both single and multi-port configurations, restoring
compatibility with HiHope boards.
Fixes: 547b02f74e4a ("ASoC: rsnd: enable multi Component support for Audio Graph Card/Card2")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/20241010141432.716868-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The variable slot_found is being initialized to zero and inside
a for-loop is being checked if it's reached MAX_NUM_CH, however,
this is currently impossible since slot_found is never changed.
In a previous loop a similar coding pattern is used and slot_found
is being incremented. It appears the increment of slot_found is
missing from the loop, so fix the code by adding in the increment.
Fixes: 6a8e1d46f062 ("ASoC: max98388: add amplifier driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20241010182032.776280-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As reported the builtin microphone doesn't work on the ASUS Vivobook
model S15 OLED M3502RA. Therefore add a quirk for it to make it work.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219345
Signed-off-by: Christian Heusel <christian@heusel.eu>
Link: https://patch.msgid.link/20241010-bugzilla-219345-asus-vivobook-v1-1-3bb24834e2c3@heusel.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When v4 topology support was removed, minimal topology ABI version
should have been bumped.
Fixes: fe4a07454256 ("ASoC: Drop soc-topology ABI v4 support")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://patch.msgid.link/20241009081230.304918-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added proper error handling for register value check that
return -EPERM when register value does not meet expected condition
Signed-off-by: Zhu Jun <zhujun2@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241009073938.7472-1-zhujun2@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During the migration of Soundwire runtime stream allocation from
the Qualcomm Soundwire controller to SoC's soundcard drivers the sdm845
soundcard was forgotten.
At this point any playback attempt or audio daemon startup, for instance
on sdm845-db845c (Qualcomm RB3 board), will result in stream pointer
NULL dereference:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000020
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000101ecf000
[0000000000000020] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ...
CPU: 5 UID: 0 PID: 1198 Comm: aplay
Not tainted 6.12.0-rc2-qcomlt-arm64-00059-g9d78f315a362-dirty #18
Hardware name: Thundercomm Dragonboard 845c (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sdw_stream_add_slave+0x44/0x380 [soundwire_bus]
lr : sdw_stream_add_slave+0x44/0x380 [soundwire_bus]
sp : ffff80008a2035c0
x29: ffff80008a2035c0 x28: ffff80008a203978 x27: 0000000000000000
x26: 00000000000000c0 x25: 0000000000000000 x24: ffff1676025f4800
x23: ffff167600ff1cb8 x22: ffff167600ff1c98 x21: 0000000000000003
x20: ffff167607316000 x19: ffff167604e64e80 x18: 0000000000000000
x17: 0000000000000000 x16: ffffcec265074160 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000000 x6 : ffff167600ff1cec
x5 : ffffcec22cfa2010 x4 : 0000000000000000 x3 : 0000000000000003
x2 : ffff167613f836c0 x1 : 0000000000000000 x0 : ffff16761feb60b8
Call trace:
sdw_stream_add_slave+0x44/0x380 [soundwire_bus]
wsa881x_hw_params+0x68/0x80 [snd_soc_wsa881x]
snd_soc_dai_hw_params+0x3c/0xa4
__soc_pcm_hw_params+0x230/0x660
dpcm_be_dai_hw_params+0x1d0/0x3f8
dpcm_fe_dai_hw_params+0x98/0x268
snd_pcm_hw_params+0x124/0x460
snd_pcm_common_ioctl+0x998/0x16e8
snd_pcm_ioctl+0x34/0x58
__arm64_sys_ioctl+0xac/0xf8
invoke_syscall+0x48/0x104
el0_svc_common.constprop.0+0x40/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x34/0xe0
el0t_64_sync_handler+0x120/0x12c
el0t_64_sync+0x190/0x194
Code: aa0403fb f9418400 9100e000 9400102f (f8420f22)
---[ end trace 0000000000000000 ]---
0000000000006108 <sdw_stream_add_slave>:
6108: d503233f paciasp
610c: a9b97bfd stp x29, x30, [sp, #-112]!
6110: 910003fd mov x29, sp
6114: a90153f3 stp x19, x20, [sp, #16]
6118: a9025bf5 stp x21, x22, [sp, #32]
611c: aa0103f6 mov x22, x1
6120: 2a0303f5 mov w21, w3
6124: a90363f7 stp x23, x24, [sp, #48]
6128: aa0003f8 mov x24, x0
612c: aa0203f7 mov x23, x2
6130: a9046bf9 stp x25, x26, [sp, #64]
6134: aa0403f9 mov x25, x4 <-- x4 copied to x25
6138: a90573fb stp x27, x28, [sp, #80]
613c: aa0403fb mov x27, x4
6140: f9418400 ldr x0, [x0, #776]
6144: 9100e000 add x0, x0, #0x38
6148: 94000000 bl 0 <mutex_lock>
614c: f8420f22 ldr x2, [x25, #32]! <-- offset 0x44
^^^
This is 0x6108 + offset 0x44 from the beginning of sdw_stream_add_slave()
where data abort happens.
wsa881x_hw_params() is called with stream = NULL and passes it further
in register x4 (5th argument) to sdw_stream_add_slave() without any checks.
Value from x4 is copied to x25 and finally it aborts on trying to load
a value from address in x25 plus offset 32 (in dec) which corresponds
to master_list member in struct sdw_stream_runtime:
struct sdw_stream_runtime {
const char * name; /* 0 8 */
struct sdw_stream_params params; /* 8 12 */
enum sdw_stream_state state; /* 20 4 */
enum sdw_stream_type type; /* 24 4 */
/* XXX 4 bytes hole, try to pack */
here-> struct list_head master_list; /* 32 16 */
int m_rt_count; /* 48 4 */
/* size: 56, cachelines: 1, members: 6 */
/* sum members: 48, holes: 1, sum holes: 4 */
/* padding: 4 */
/* last cacheline: 56 bytes */
Fix this by adding required calls to qcom_snd_sdw_startup() and
sdw_release_stream() to startup and shutdown routines which restores
the previous correct behaviour when ->set_stream() method is called to
set a valid stream runtime pointer on playback startup.
Reproduced and then fix was tested on db845c RB3 board.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 15c7fab0e047 ("ASoC: qcom: Move Soundwire runtime stream alloc to soundcards")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org> # Lenovo Yoga C630
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://patch.msgid.link/20241009213922.999355-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add missing snd_soc_dai_link.platforms assignment to avoid
soc_dai_link_sanity_check() failure.
Fixes: d24028606e76 ("ASoC: loongson: Add Loongson ASoC Sound Card Support")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://patch.msgid.link/6645888f2f9e8a1d8d799109f867d0f97fd78c58.1728459624.git.zhoubinbin@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current implementation does not work for widgets of DAPMs without
component, as snd_soc_dapm_to_component() requires it. If the widget is
directly owned by the card, e.g. as it is the case for the tegra
implementation, the call leads to UB. Therefore directly access the
component of the widget's DAPM to be able to check if a component is
available.
Fixes: f82eb06a40c8 ("ASoC: tegra: machine: Handle component name prefix")
Cc: stable@vger.kernel.org # v6.7+
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://patch.msgid.link/20241008-tegra-dapm-v2-1-5e999cb5f0e7@skidata.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 9ee3f0d8c999 ("ASOC: SOF: Intel: hda-loader: only wait for
HDaudio IOC for IPC4 devices") removed DMA wait for IPC3 case.
Proceed and remove the wait for IPC4 devices as well.
There is no dependency to IPC version in the load logic and
checking the firmware status is a sufficient check in case of
errors.
The removed code also had a bug in that -ETIMEDOUT is returned
without stopping the DMA transfer.
Cc: stable@vger.kernel.org
Link: https://github.com/thesofproject/linux/issues/5135
Fixes: 9ee3f0d8c999 ("ASOC: SOF: Intel: hda-loader: only wait for HDaudio IOC for IPC4 devices")
Suggested-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20241008060710.15409-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Incorrect SRAM base addr for acp7.0 platform results firmware boot
failure.
Add condition check to support SRAM addr for various platforms.
Fixes: 145d7e5ae8f4 ("ASoC: SOF: amd: add option to use sram for data bin loading")
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20241008091347.594378-2-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add dev_err to print ACP_SHA_DSP_FW_QUALIFIER and ACP_SHA_PSP_ACK
register values for PSP firmware validation failure case.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://patch.msgid.link/20241008091347.594378-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Function snd_pcm_period_elapsed() is part of sequence servicing HDAudio
stream IRQs. It's called under Global Interrupt Enable (GIE) disabled -
no HDAudio interrupts will be raised. At the same time, the function may
end up calling __snd_pcm_xrun() or snd_pcm_drain_done(). On the
avs-driver side, this translates to IPCs and as GIE is disabled, these
will never complete successfully.
Improve system stability by scheduling stream-IRQ handling in a separate
thread.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20241008083758.756578-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Combinations of "tx" alone, "rx" alone and "tx", "rx" together are
supposedly valid (see link below), which is not the case today as "rx"
alone is not accepted by the current binding.
Let's rework the two interrupt properties to expose all correct
possibilities.
Cc: Péter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/linux-sound/20241003102552.2c11840e@xps-13/T/#m277fce1d49c50d94e071f7890aed472fa2c64052
Fixes: 8be90641a0bb ("ASoC: dt-bindings: davinci-mcasp: convert McASP bindings to yaml schema")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241003083611.461894-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A devm_kzalloc() in asoc_qcom_lpass_cpu_platform_probe() could
possibly return NULL pointer. NULL Pointer Dereference may be
triggerred without addtional check.
Add a NULL check for the returned pointer.
Fixes: b5022a36d28f ("ASoC: qcom: lpass: Use regmap_field for i2sctl and dmactl registers")
Cc: stable@vger.kernel.org
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com>
Link: https://patch.msgid.link/20241006205737.8829-1-zichenxie0106@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Move non-boot built-in DTBs to the .rodata section
- Fix Kconfig bugs
- Fix maint scripts in the linux-image Debian package
- Import some list macros to scripts/include/
* tag 'kbuild-fixes-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: deb-pkg: Remove blank first line from maint scripts
kbuild: fix a typo dt_binding_schema -> dt_binding_schemas
scripts: import more list macros
kconfig: qconf: fix buffer overflow in debug links
kconfig: qconf: move conf_read() before drawing tree pain
kconfig: clear expr::val_is_valid when allocated
kconfig: fix infinite loop in sym_calc_choice()
kbuild: move non-boot built-in DTBs to .rodata section
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Intel PMC fix for suspend/resume issues on some Sky and Kaby Lake
laptops
- Intel Diamond Rapids hw-id additions
- Documentation and MAINTAINERS fixes
- Some other small fixes
* tag 'platform-drivers-x86-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: x86-android-tablets: Fix use after free on platform_device_register() errors
platform/x86: wmi: Update WMI driver API documentation
platform/x86: dell-ddv: Fix typo in documentation
platform/x86: dell-sysman: add support for alienware products
platform/x86/intel: power-domains: Add Diamond Rapids support
platform/x86: ISST: Add Diamond Rapids to support list
platform/x86:intel/pmc: Disable ACPI PM Timer disabling on Sky and Kaby Lake
platform/x86: dell-laptop: Do not fail when encountering unsupported batteries
MAINTAINERS: Update Intel In Field Scan(IFS) entry
platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM64:
- Fix pKVM error path on init, making sure we do not change critical
system registers as we're about to fail
- Make sure that the host's vector length is at capped by a value
common to all CPUs
- Fix kvm_has_feat*() handling of "negative" features, as the current
code is pretty broken
- Promote Joey to the status of official reviewer, while James steps
down -- hopefully only temporarly
x86:
- Fix compilation with KVM_INTEL=KVM_AMD=n
- Fix disabling KVM_X86_QUIRK_SLOT_ZAP_ALL when shadow MMU is in use
Selftests:
- Fix compilation on non-x86 architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/reboot: emergency callbacks are now registered by common KVM code
KVM: x86: leave kvm.ko out of the build if no vendor module is requested
KVM: x86/mmu: fix KVM_X86_QUIRK_SLOT_ZAP_ALL for shadow MMU
KVM: arm64: Fix kvm_has_feat*() handling of negative features
KVM: selftests: Fix build on architectures other than x86_64
KVM: arm64: Another reviewer reshuffle
KVM: arm64: Constrain the host to the maximum shared SVE VL with pKVM
KVM: arm64: Fix __pkvm_init_vcpu cptr_el2 error path
|