Age | Commit message (Collapse) | Author |
|
Merge series from Ariel D'Alessandro <ariel.dalessandro@collabora.com>:
This patchset modifies the tlv320aic31xx driver to update its sysclk if
BCLK is used as the input clock. This allows to be used by the generic
fsl-asoc-card, without having to add a specific driver.
|
|
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
When a pipeline is marked dynamic in the SOF DSP firmware
topology definition (the tplg file kernel loads from filesystem),
it means the pipeline resources are not allocated when DSP is
booted (at driver probe, or at runtime resume), but rather delayed
until the pipeline is actually used.
|
|
Add entry for fsl,imx-audio-tlv320aic31xx audio codec. This codec is
configured to use BCLK as clock input.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20211119153248.419802-6-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If BCLK is used as PLL input, the sysclk is determined by the hw
params. So it must be updated here to match the input frequency, based
on sample rate, format and channels.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20211119153248.419802-5-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add divisors for rates needed when the clk_in is set to BCLK.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20211119153248.419802-4-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the clock used by the codec is BCLK, the operation parameters need
to be calculated from input sample rate and format. Low frequency rates
required different r multipliers, in order to achieve a higher PLL
output frequency.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20211119153248.419802-3-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20211119153248.419802-2-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When a jack handler is registered in cs42l42_set_jack() the
initial state should be reported if an attached headphone/headset
has already been detected.
The jack detect sequence takes around 1 second: typically long
enough for the machine driver to probe and register the jack handler
in time to receive the first report from the interrupt handler. So
it is possible on some systems that the correct initial state was seen
simply because of lucky timing. Modular builds were more likely to
miss the reporting of the initial state.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 4ca239f33737 ("ASoC: cs42l42: Always enable TS_PLUG and TS_UNPLUG interrupts")
Link: https://lore.kernel.org/r/20211119124854.58939-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are already 3 versions of the Up boards with support for the SOF
community key (ApolloLake, WhiskyLake, TigerLake). Rather than
continue to add quirks for each version, let's add a wildcard.
For WHL and TGL, the authentication supports both the SOF community
key and the firmware signed with the Intel production key. Given two
choices, the community key is the preferred option to allow developers
to sign their own firmware. The firmware signed with production key
can still be selected if needed with a kernel module
option (snd-sof-pci.fw_path="intel/sof")
Tested-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211119231327.211946-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable support of pm_runtime on STM32 SPDIFRX driver to allow
SPDIFRX power state monitoring.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20211119104752.13564-4-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable support of pm_runtime on STM32 DFSDM audio driver
to allow power state monitoring.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20211119104752.13564-3-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Enable support of pm_runtime on STM32 I2S driver to allow
I2S power state monitoring.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20211119104752.13564-2-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To keep the widget use_counts balanced, free the DAI widget
during suspend and also during the stop trigger.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-11-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support for dynamic pipelines with multi-core
by using the platform-specific core_get/put() ops to
power up/down a core when a widget is set up/freed.
Along with this, a few redundant functions are removed:
1. sof_pipeline_core_enable() is no longer needed as the
pipeline core will be set up when the pipeline widget
is set up
2. sof_core_enable() is replaced with snd_sof_core_get()
4. core_power_up/down() DSP ops are deprecated and replaced with
core get/put ops.
5. Core power down in sof_widget_unload() during topology
removal is also removed as it is not really needed. For dynamic
pipelines, the cores will be powered off when they are not used.
For static pipelines, the cores will be powered off in the device
remove callback.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-10-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The core_power_up/down() ops will be deprecated. Use the
HDA platform-specific functions for powering up/down
the cores during probe/suspend/remove. The enabled_cores_mask
and the core ref_count's are manually updated in each of
these functions.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-9-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Free widgets for static pipelines in sof_tear_down_pipelines().
But this feature is unavailable in older firmware with ABI < 3.19.
Just reset widget use_count's for this case. This would ensure that
the secondary cores enabled required for topology setup are powered
down properly before the primary core is powered off during
system suspend.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-8-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the function sof_load_pipeline_ipc() and directly
send the IPC instead. The pipeline core is already enabled
with the call to sof_pipeline_core_enable() in sof_widget_setup().
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-7-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set core_get/put ops for CNL/ICL platforms. These platforms
do not support enabling/disabling secondary cores
dynamically. So skip sending the IPC to power off the
cores in the core_put op.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-6-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set core_get/put() ops for TGL. When core_get()
is requested for a core, its ref_count is incremented
and the PM_CORE_ENABLE IPC sent to the firmware to
power up the core if the current ref_count is 1.
Conversely, the ref_count is decremented in core_put()
and an IPC is sent to the DSP to power off the core
if the ref_count is 0.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-5-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add ops to get/put a core that will be used to power
up/down a core along with incrementing/decrementing
its ref_count.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-4-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add two fields num_cores and dsp_cores_ref_count to
struct snd_sof_dev. These will be used to maintain the
ref count for each core to determine when it should be
powered up or down.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
expose get_chip_info().
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119192621.4096077-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Resume common flow (System PM / Runtime PM) is like this:
sof_resume
-> specific device resume
-> snd_sof_load_firmware
-> snd_sof_dsp_reset (1)
-> load_modules()
-> snd_sof_run_firmware (2)
We need to implement dsp_reset callback (1) that will actually reset
the DSP but keep it stalled.
In order to implement this we do the following:
-> put DSP into reset (assert CoreReset bit from PWRCTL)
-> stall the DSP using RunStall bit from AudioDSP_REG2 mix
-> take DSP out of reset (de-assert CoreReset bit from PWRCTL)
At this moment the DSP is taken out of reset and Stalled! This means
that we can load the firmware and then start the DSP (2).
Until now we resetted the DSP by turning down the Audiomix PD. This
doesn't work for Runtime PM if another IP is keeping Audiomix PD up.
By introducing dsp_reset() we no longer rely on turning off the
audiomix to reset the DSP.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211119094319.81674-6-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On i.MX8M DSP is controlled via a set of registers
from Audio MIX. This patches gets a reference (via regmap)
to Audio Mix registers and implements DSP start.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211119094319.81674-5-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We make use of common imx8m_suspend / imx8m_resume functions
for both system PM and runtime PM.
imx8m_suspend:
- frees the MU channels
- disables the clocks
imx8m_resume
- enables the clocks
- requests the MU channels
On i.MX8MP there is no dedicated functionality to put the DSP in reset.
The only way of doing this is to POWER DOWN the Audiomix domain.
We are able to do this because turning off the clocks and freeing the
channels makes the Audiomix to have no users thus PM kernel core turns
it down.
SOF core will not call system PM suspend handler if the DSP is already
down, but at resume it will call the system PM resume. So, we need to
keep track of the state via snd_sof_dsp_set_power_state
Few insights on how SOF core handles the PM:
- SOF core uses PM runtime autosuspend (with a timeout of 2 secs)
- at probe, SOF core boots the DSP and lets the PM runtime suspend to
turn it off, if there is no activity
- when someone opens the ALSA sound card (aplay/arecord, etc) ALSA core
calls PM runtime resume to turn on the DSP
- when the ALSA sound card is closed SOF core make use of PM subsystem
to call PM runtime suspend and thus turning off the DSP.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211119094319.81674-4-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Handle clocks and mailbox channels at runtime suspend/resume
in order to save power.
DSP runtime PM uses a timeout of 2s. If device
is idle for 2s system will enter runtime suspend.
Because SOF state machine assumes that even if the DSP wasn't previously
active at a System resume, will re-load the firmware we need to make sure
that all needed resources are active.
Kernel core will take care of enabling the PD, we need to make sure that
we request the MU channels.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211119094319.81674-3-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need at least 3 clocks in order to power up and access
DSP core registers found on i.MX8QM, i.MX8QXP and i.MX8MP
platforms.
Add code to request these clocks and enable them at probe. Next
patches will add PM support which will only activate clocks when
DSP is used.
DSP clocks are already documented in
Documentation/devicetree/bindings/dsp/fsl,dsp.yaml
We choose to add:
* imx8_parse_clocks
* imx8_enable_clocks
* imx8_disable_clocks
wrappers because in the future DSP will need to take care about the
clocks of other related Audio IPs (e.g SAI, ESAI).
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211119094319.81674-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Without a module alias, autoloading the driver does not occurr
when it is built as a module.
By adding a module alias, the driver now probes fine automatically
and therefore analog audio output works as it should.
Fixes: 0d6a04da9b25 ("ASoC: Add Rockchip rk817 audio CODEC support")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211121150521.159543-1-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit dac7cbd55dca ("ASoC: Intel: soc-acpi-byt: shrink tables using
compatible IDs") and commit 959ae8215a9e ("ASoC: Intel: soc-acpi-cht:
shrink tables using compatible IDs") simplified the match tables in
soc-acpi-intel-byt-match.c and soc-acpi-intel-cht-match.c by merging
identical entries using the new .comp_ids snd_soc_acpi_mach field to
point a single entry to multiple ACPI HIDs and clearing the previously
unique per entry .id field.
But various machine drivers from sound/soc/intel/boards rely on mach->id
in one or more ways, e.g. some drivers contain the following snippets:
adev = acpi_dev_get_first_match_dev(mach->id, NULL, -1);
pkg_found = snd_soc_acpi_find_package_from_hid(mach->id, ...
if (!strncmp(snd_soc_cards[i].codec_id, mach->id, 8)) { ...
All of which are broken by the match table shrinking.
Make the snd_soc_acpi_mach.id field non const (the storage for the tables
already is non const) and on a comps_ids match copy the matching HID to
the id field to fix this.
Fixes: dac7cbd55dca ("ASoC: Intel: soc-acpi-byt: shrink tables using compatible IDs")
Fixes: 959ae8215a9e ("ASoC: Intel: soc-acpi-cht: shrink tables using compatible IDs")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Brent Lu <brent.lu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211118153014.349222-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Filter
out duplicate updates in Mixer driver.
Fixes: 05bb3d5ec64a ("ASoC: tegra: Add Tegra210 based Mixer driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-17-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Filter
out duplicate updates in ADX driver.
Fixes: a99ab6f395a9 ("ASoC: tegra: Add Tegra210 based ADX driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-16-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Filter
out duplicate updates in AMX driver.
Fixes: 77f7df346c45 ("ASoC: tegra: Add Tegra210 based AMX driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-15-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Filter
out duplicate updates in SFC driver.
Fixes: b2f74ec53a6c ("ASoC: tegra: Add Tegra210 based SFC driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-14-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Filter
out duplicate updates in MVC driver.
Fixes: e539891f9687 ("ASoC: tegra: Add Tegra210 based MVC driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-13-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the AHUB driver accordingly.
Fixes: 16e1bcc2caf4 ("ASoC: tegra: Add Tegra210 based AHUB driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-12-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DSPK driver accordingly.
Fixes: 327ef6470266 ("ASoC: tegra: Add Tegra186 based DSPK driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-11-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DMIC driver accordingly.
Fixes: 8c8ff982e9e2 ("ASoC: tegra: Add Tegra210 based DMIC driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-10-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the I2S driver accordingly.
Fixes: c0bfa98349d1 ("ASoC: tegra: Add Tegra210 based I2S driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-9-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the ADMAIF driver accordingly.
Fixes: f74028e159bb ("ASoC: tegra: Add Tegra210 based ADMAIF driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-8-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: e539891f9687 ("ASoC: tegra: Add Tegra210 based MVC driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-7-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: b2f74ec53a6c ("ASoC: tegra: Add Tegra210 based SFC driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-6-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: 327ef6470266 ("ASoC: tegra: Add Tegra186 based DSPK driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-5-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: 8c8ff982e9e2 ("ASoC: tegra: Add Tegra210 based DMIC driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: c0bfa98349d1 ("ASoC: tegra: Add Tegra210 based I2S driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.
Fixes: f74028e159bb ("ASoC: tegra: Add Tegra210 based ADMAIF driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Daniel Baluta <daniel.baluta@oss.nxp.com>:
This adds sound open firmware driver support for MT8915 platform.
|
|
Remove redundant conditional check and clean code in special
headset support functions.
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Co-developed-by: Venkata Prasad Potturu <potturu@codeaurora.org>
Signed-off-by: Venkata Prasad Potturu <potturu@codeaurora.org>
Link: https://lore.kernel.org/r/1637234411-554-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add DSP system PM callback for suspend and resume
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211118100749.54628-9-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add adsp clock on/off support on mt8195 platform.
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211118100749.54628-8-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add dsp ops callback to register AFE DL2/DL3/UL4/UL5 sof dai's with ALSA
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211118100749.54628-7-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|