| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
|
|
Update the Hyper-V MAINTAINERS to include myself.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring
The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f6e ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aab7 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rather than keep a list of all possible compression types in the
Makefile, set the target explicitly from Kconfig.
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When using initramfs compression, the data file compression suffix
gets quotes pulled in from Kconfig, e.g., initramfs_data.cpio".gz"
which make does not match a target and causes rebuild.
Fix this by filtering out quotes from the Kconfig string.
Fixes: 35e669e1a254 ("initramfs: select builtin initram compression algorithm on KConfig instead of Makefile")
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc3
These fixes address a number of long-standing issues in various
USB-serial drivers which would lead to crashes should a malicious device
lack the expected endpoints.
Included are also a few related fixes, and a couple of unrelated ones
that were found during my survey (e.g. a memleak and a
sleep-while-atomic).
A compiler warning revealed an error-handling issue in the new f81534
driver which is also fixed.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Linus reported that commit 174cc7187e6f "ACPICA: Tables: Back port
acpi_get_table_with_size() and early_acpi_os_unmap_memory() from
Linux kernel" added a new warning on his desktop system:
ACPI Warning: Table ffffffff9fe6c0a0, Validation count is zero before decrement
which turns out to come from the acpi_put_table() in
detect_intel_iommu().
This happens if the DMAR table is not present in which case NULL is
passed to acpi_put_table() which doesn't check against that and
attempts to handle it regardless.
For this reason, check the pointer passed to acpi_put_table()
before invoking it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Fixes: 6b11d1d67713 ("ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Declaration of VMX_VPID_EXTENT_SUPPORTED_MASK occures twice in the code.
Probably, it was happened after unsuccessful merge.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
Flush the KVM entry code from the icache on all CPUs, not just the one
that built the entry code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.16.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
On 64-bit kernels, MIPS KVM will clear CP0_Status.UX to prevent the
guest (running in user mode) from accessing the 64-bit memory segments.
However the previous value of CP0_Status.UX is never restored when
exiting from the guest.
If the user process uses 64-bit addressing (the n64 ABI) this can result
in address error exceptions from the kernel if it needs to deliver a
signal before returning to user mode, as the kernel will need to write a
sigframe to high user addresses on the user stack which are disallowed
by CP0_Status.UX=0.
This is fixed by explicitly setting SX and UX again when exiting from
the guest, and explicitly clearing those bits when returning to the
guest. Having the SX and UX bits set when handling guest exits (rather
than only when exiting to userland) will be helpful when we support VZ,
since we shouldn't need to directly read or write guest memory, so it
will be valid for cache management IPIs to access host user addresses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.8.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
The Turris Omnia features a Marvell MV88E6176 ethernet switch. Add it to
the dts.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Move the uart nodes over to use the label form to reference the serial
devices, rather than replicating the device node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Move the ethernet, buffer manager, and mdio nodes over to use label form
to reference the devices rather than replicating the device path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Move the I2C nodes over to use the label form to reference the I2C
controllers, rather than replicating the device node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Move the device specific pinctrl nodes over to use the label form to
reference the pin mux controller, rather than replicating the device
node path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the DTS file to describe the clearfog pro model - we update the
platform name and compatible string compared to the original version.
The original version remains for compatibility for the time being as
the name of the file has become established, and the machine name
and/or compatible may be used by userspace.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Add the DTS file to describe the clearfog base model.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Adjust regs property for the FPGA manager data register to
properly reflect that it is a single 32 bit register.
Signed-off-by: Dalon Westergreen <dwesterg@altera.com>
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add socfpga_arria10_socdk_nand.dts board file for supporting NAND.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: move nand dts node to socfpga_arria10.dtsi
|
|
The asm-prototypes.h file is used to provide dummy function declarations
for genksyms, when processing asm files with EXPORT_SYMBOL. Make sure
that any architecture defines get out of our way. x86 currently has an
issue with memcpy on 64bit with CONFIG_KMEMCHECK=y and with
memset/__memset on 32bit:
$ cat init/test.c
#include <asm/asm-prototypes.h>
$ make -s init/test.o
In file included from ./arch/x86/include/asm/string.h:4:0,
from ./include/linux/string.h:18,
from ./include/linux/bitmap.h:8,
from ./include/linux/cpumask.h:11,
from ./arch/x86/include/asm/cpumask.h:4,
from ./arch/x86/include/asm/msr.h:10,
from ./arch/x86/include/asm/processor.h:20,
from ./arch/x86/include/asm/cpufeature.h:4,
from ./arch/x86/include/asm/thread_info.h:52,
from ./include/linux/thread_info.h:25,
from ./arch/x86/include/asm/preempt.h:6,
from ./include/linux/preempt.h:59,
from ./include/linux/spinlock.h:50,
from ./include/linux/seqlock.h:35,
from ./include/linux/time.h:5,
from ./include/uapi/linux/timex.h:56,
from ./include/linux/timex.h:56,
from ./include/linux/sched.h:19,
from ./include/linux/uaccess.h:4,
from ./arch/x86/include/asm/asm-prototypes.h:2,
from init/test.c:1:
./arch/x86/include/asm/string_64.h:52:47: error: expected declaration specifiers or ‘...’ before ‘(’ token
#define memcpy(dst, src, len) __inline_memcpy((dst), (src), (len))
./include/asm-generic/asm-prototypes.h:6:14: note: in expansion of macro ‘memcpy’
extern void *memcpy(void *, const void *, __kernel_size_t);
^
...
During real build, this manifests itself by genksyms segfaulting.
Fixes: 334bb7738764 ("x86/kbuild: enable modversions for symbols exported from asm")
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Michal Marek <mmarek@suse.com>
|
|
This reverts commit 6b7e95d1336b9eb0d4c6db190ce756480496bd13. This commit
is based on a concern about value of the given parameter. It's expected
to be ORed value with some enumeration-constants, thus often it can not be
one of the enumeration-constants. I understood that this is out of
specification and causes implementation-dependent issues.
In C language specification, enumerated type can be interpreted as an
integer type, in which all of enumeration-constants in corresponding
enumerator-list can be stored. Implementations can select one of char,
signed int and unsigned int as its type, and this selection is
implementation-dependent.
In GCC, a signed integer is selected when at least one of
enumeration-constants has negative value, else an unsigned integer is
selected. This behaviour can be switched by -fshort-enums to short type.
Anyway, the type can be decided after scanning all of
enumeration-constants.
Totally, there's no rules to constrain the value of enumerated type to
be one of enumeration-constants. In short, in enumerated type, decision
of actual type for the type is the most important and
enumeration-constants are just used for the decision, thus it's permitted
to have an integer value in a range of enumeration-constants. In our case,
actual type for the type is currently deterministic to be either char or
unsigned int. Under GCC, it's unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Testing EP_FLAG_RUNNING in snd_complete_urb() before running the completion
logic allows us to save a few cpu cycles by returning early, skipping the
pending urb in case the stream was stopped; the stop logic handles the urb
and sets the completion callbacks to NULL.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 16200948d83 ("ALSA: usb-audio: Fix race at stopping the stream") was
incomplete causing another more severe kernel panic, so it got reverted.
This fixes both the original problem and its fallout kernel race/crash.
The original fix is to move the endpoint member NULL clearing logic inside
wait_clear_urbs() so the irq triggering the urb completion doesn't call
retire_capture/playback_urb() after the NULL clearing and generate a panic.
However this creates a new race between snd_usb_endpoint_start()'s call
to wait_clear_urbs() and the irq urb completion handler which again calls
retire_capture/playback_urb() leading to a new NULL dereference.
We keep the EP deactivation code in snd_usb_endpoint_start() because
removing it will break the EP reference counting (see [1] [2] for info),
however we don't need the "can_sleep" mechanism anymore because a new
function was introduced (snd_usb_endpoint_sync_pending_stop()) which
synchronizes pending stops and gets called inside the pcm prepare callback.
It also makes sense to remove can_sleep because it was also removed from
deactivate_urbs() signature in [3] so we benefit from more simplification.
[1] commit 015618b90 ("ALSA: snd-usb: Fix URB cancellation at stream start")
[2] commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in PCM capture stream")
[3] commit ccc1696d5 ("ALSA: usb-audio: simplify endpoint deactivation code")
Fixes: f8114f8583bb ("Revert "ALSA: usb-audio: Fix race at stopping the stream"")
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fixes for crashes and double-cleanup errors
- XFS maintainership handover
- fix to prevent absurdly large block reservations
- fix broken sysfs getter/setters
* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix max_retries _show and _store functions
xfs: update MAINTAINERS
xfs: fix crash and data corruption due to removal of busy COW extents
xfs: use the actual AG length when reserving blocks
xfs: fix double-cleanup when CUI recovery fails
|
|
Add the FPGA manger DTS entry for Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the I2C LTC 2977 power monitor that is on the Arria10 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the watchdog for Arria5 and Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the CAN node on the Cyclone5 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the SPI node and add the Rohm DH2228FV DAC.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The I2C LCD display on the Cyclone5 and Arria5 devkits is only capable of
the standard 100 kHz clock. Set the "clock-frequency" of the I2C node
to be 100000.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable all the GPIO ports and define the GPIO-based leds on the Cyclone5 and
Arria5 devkits.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the compatible string for supporting the generic device tree cpufreq-dt
driver on APM's X-Gene 2 SoC.
Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull networking fixes from David Miller:
1) stmmac_drv_probe() can race with stmmac_open() because we register
the netdevice too early. Fix from Florian Fainelli.
2) UFO handling in __ip6_append_data() and ip6_finish_output() use
different tests for deciding whether a frame will be fragmented or
not, put them in sync. Fix from Zheng Li.
3) The rtnetlink getstats handlers need to validate that the netlink
request is large enough, fix from Mathias Krause.
4) Use after free in mlx4 driver, from Jack Morgenstein.
5) Fix setting of garbage UID value in sockets during setattr() calls,
from Eric Biggers.
6) Packet drop_monitor doesn't format the netlink messages properly
such that nlmsg_next fails to work, fix from Reiter Wolfgang.
7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
Nault.
8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.
9) IGMP code doesn't reset group query timers properly, from Michal
Tesar.
10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
Alexander Duyck.
11) vxlan offload check needs to be more strict in be2net driver, from
Sabrina Dubroca.
12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
fix from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sh_eth: enable RX descriptor word 0 shift on SH7734
sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
dpaa_eth: Initialize CGR structure before init
dpaa_eth: cleanup after init_phy() failure
net: systemport: Pad packet before inserting TSB
net: systemport: Utilize skb_put_padto()
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
libcxgb: fix error check for ip6_route_output()
net: usb: asix_devices: add .reset_resume for USB PM
net: vrf: Add missing Rx counters
drop_monitor: consider inserted data in genlmsg_end
benet: stricter vxlan offloading check in be_features_check
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
net: macb: Updated resource allocation function calls to new version of API.
net: stmmac: dwmac-oxnas: use generic pm implementation
net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
net: stmmac: dwmac-oxnas: fix of-node leak
Documentation/networking: fix typo in mpls-sysctl
igmp: Make igmp group member RFC 3376 compliant
flow_dissector: Update pptp handling to avoid null pointer deref.
...
|
|
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4f8 ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although the old quirk table showed ASUS X71SL with ALC663 codec being
compatible with asus-mode3 fixup, the bugzilla reporter explained that
asus-model8 fits better for the dual headphone controls. So be it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191781
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
What appears to be a copy and paste error from the line above gets
the ioctl a ssize_t return value instead of the traditional "int".
The associated sample code used "long" which meant it would compile
for x86-64 but not i386, with the latter failing as follows:
CC [M] samples/vfio-mdev/mtty.o
samples/vfio-mdev/mtty.c:1418:20: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.ioctl = mtty_ioctl,
^
samples/vfio-mdev/mtty.c:1418:20: note: (near initialization for ‘mdev_fops.ioctl’)
cc1: some warnings being treated as errors
Since in this case, vfio is working with struct file_operations; as such:
long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
...and so here we just standardize on long vs. the normal int that user
space typically sees and documents as per "man ioctl" and similar.
Fixes: 9d1a546c53b4 ("docs: Sample driver to demonstrate how to use Mediated device framework.")
Cc: Kirti Wankhede <kwankhede@nvidia.com>
Cc: Neo Jia <cjia@nvidia.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
If we failed to set up RSS on EF10 (e.g. because firmware declared
RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
no fields, rather than confusingly reporting what fields we _would_ be
hashing on if RSS was working.
Fixes: dcb4123cbec0 ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Madalin Bucur says:
====================
dpaa_eth: a couple of fixes
Add cleanup on PHY initialization failure path, avoid using
uninitialized memory at CGR init.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: systemport: Fix padding vs. TSB insertion
This patch series fixes how we pad the packets submitted to the SYSTEMPORT
adapter, and how the transmit status block (prepended 8 bytes) fits in the
picture. The first patch is not technically a bug fix, but is required for the
second path to be applied and to greatly simplify the skb length calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
