Age | Commit message (Collapse) | Author |
|
I have observed an issue where the RX direction of the LS1028A ENETC pMAC
seems unresponsive. The minimal procedure to reproduce the issue is:
1. Connect ENETC port 0 with a loopback RJ45 cable to one of the Felix
switch ports (0).
2. Bring the ports up (MAC Merge layer is not enabled on either end).
3. Send a large quantity of unidirectional (express) traffic from Felix
to ENETC. I tried altering frame size and frame count, and it doesn't
appear to be specific to either of them, but rather, to the quantity
of octets received. Lowering the frame count, the minimum quantity of
packets to reproduce relatively consistently seems to be around 37000
frames at 1514 octets (w/o FCS) each.
4. Using ethtool --set-mm, enable the pMAC in the Felix and in the ENETC
ports, in both RX and TX directions, and with verification on both
ends.
5. Wait for verification to complete on both sides.
6. Configure a traffic class as preemptible on both ends.
7. Send some packets again.
The issue is at step 5, where the verification process of ENETC ends
(meaning that Felix responds with an SMD-R and ENETC sees the response),
but the verification process of Felix never ends (it remains VERIFYING).
If step 3 is skipped or if ENETC receives less traffic than
approximately that threshold, the test runs all the way through
(verification succeeds on both ends, preemptible traffic passes fine).
If, between step 4 and 5, the step below is also introduced:
4.1. Disable and re-enable PM0_COMMAND_CONFIG bit RX_EN
then again, the sequence of steps runs all the way through, and
verification succeeds, even if there was the previous RX traffic
injected into ENETC.
Traffic sent *by* the ENETC port prior to enabling the MAC Merge layer
does not seem to influence the verification result, only received
traffic does.
The LS1028A manual does not mention any relationship between
PM0_COMMAND_CONFIG and MMCSR, and the hardware people don't seem to
know for now either.
The bit that is toggled to work around the issue is also toggled
by enetc_mac_enable(), called from phylink's mac_link_down() and
mac_link_up() methods - which is how the workaround was found:
verification would work after a link down/up.
Fixes: c7b9e8086902 ("net: enetc: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230411192645.1896048-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.
This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.
Fixes: 0fc2ea922c8a ("sctp: implement validate_ftsn for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/2a71bffcd80b4f2c61fac6d344bb2f11c8fd74f7.1681155810.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.3-2023-04-12:
amdgpu:
- SMU13 fixes
- DP MST fix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230412215637.7881-1-alexander.deucher@amd.com
|
|
Syzbot reported a bug as following:
=====================================================
BUG: KMSAN: uninit-value in qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_endpoint_post+0xf85/0x11b0 net/qrtr/af_qrtr.c:519
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
__netdev_alloc_skb+0x120/0x7d0 net/core/skbuff.c:630
qrtr_endpoint_post+0xbd/0x11b0 net/qrtr/af_qrtr.c:446
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.
Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug.
Fixes: 5fdeb0d372ab ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+4436c9630a45820fda76@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=c14607f0963d27d5a3d5f4c8639b500909e43540
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230410012352.3997823-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commits referenced below allows userspace to use the NLM_F_ECHO flag
for RTM_NEW/DELLINK operations to receive unicast notifications for the
affected link. Prior to these changes, applications may have relied on
multicast notifications to learn the same information without specifying
the NLM_F_ECHO flag.
For such applications, the mentioned commits changed the behavior for
requests not using NLM_F_ECHO. Multicast notifications are still received,
but now use the portid of the requester and the sequence number of the
request instead of zero values used previously. For the application, this
message may be unexpected and likely handled as a response to the
NLM_F_ACKed request, especially if it uses the same socket to handle
requests and notifications.
To fix existing applications relying on the old notification behavior,
set the portid and sequence number in the notification only if the
request included the NLM_F_ECHO flag. This restores the old behavior
for applications not using it, but allows unicasted notifications for
others.
Fixes: f3a63cce1b4f ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_delete_link")
Fixes: d88e136cab37 ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_newlink_create")
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20230411074319.24133-1-martin@strongswan.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- kernel panic fix for intel-ish-hid driver (Tanu Malhotra)
- buffer overflow fix in hid-sensor-custom driver (Todd Brandt)
- two device specific quirks (Alessandro Manca, Philippe Troin)
* tag 'for-linus-2023041201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: Fix kernel panic during warm reset
HID: hid-sensor-custom: Fix buffer overrun in device name
HID: topre: Add support for 87 keys Realforce R2
HID: add HP 13t-aw100 & 14t-ea100 digitizer battery quirks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A couple of fixes in apple driver, core and kernedoc fix for dmaengine
subsystem:
- apple admac driver fixes for current_tx, src_addr_widths and
global' interrupt flags handling
- xdma kerneldoc fix
- core fix for use of devm_add_action_or_reset"
* tag 'dmaengine-fix-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: apple-admac: Fix 'current_tx' not getting freed
dmaengine: apple-admac: Set src_addr_widths capability
dmaengine: apple-admac: Handle 'global' interrupt flags
dmaengine: xilinx: xdma: Fix some kernel-doc comments
dmaengine: Actually use devm_add_action_or_reset()
|
|
Update the driver implementations to fit those data exposed
by PMFW.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Correct the max shader clock reporting on SMU
13.0.7.
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Correct the pstate standard/peak profiling mode clock
settings for SMU13.0.7.
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
[Why & How]
drm_dp_remove_payload() interface was changed. Correct amdgpu dm code
to pass the right parameter to the drm helper function.
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix netfs_extract_iter_to_sg() for ITER_UBUF and ITER_IOVEC to set the
size of the page to the part of the page extracted, not the remaining
amount of data in the extracted page array at that point.
This doesn't yet affect anything as cifs, the only current user, only
passes in non-user-backed iterators.
Fixes: 018584697533 ("netfs: Add a function to extract an iterator into a scatterlist")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: Steve French <sfrench@samba.org>
Cc: Shyam Prasad N <nspmangalore@gmail.com>
Cc: Rohith Surabattula <rohiths.msft@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We were stuck on rc2, should at least attempt to track drm-fixes
slightly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
TI CPSW uses of_platform_* functions which are declared in of_platform.h.
of_platform.h gets implicitly included by of_device.h, but that is going
to be removed soon. Nothing else depends on of_device.h so it can be
dropped. of_platform.h also implicitly includes platform_device.h, so
add an explicit include for it, too.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch reports:
drivers/net/wwan/iosm/iosm_ipc_pcie.c:298 ipc_pcie_probe()
warn: missing unwind goto?
When dma_set_mask fails it directly returns without disabling pci
device and freeing ipc_pcie. Fix this my calling a correct goto label
As dma_set_mask returns either 0 or -EIO, we can use a goto label, as
it finally returns -EIO.
Add a set_mask_fail goto label which stands consistent with other goto
labels in this function..
Fixes: 035e3befc191 ("net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With Eric's ref tracker, syzbot finally found a repro for
use-after-free in tcp_write_timer_handler() by kernel TCP
sockets. [0]
If SMC creates a kernel socket in __smc_create(), the kernel
socket is supposed to be freed in smc_clcsock_release() by
calling sock_release() when we close() the parent SMC socket.
However, at the end of smc_clcsock_release(), the kernel
socket's sk_state might not be TCP_CLOSE. This means that
we have not called inet_csk_destroy_sock() in __tcp_close()
and have not stopped the TCP timers.
The kernel socket's TCP timers can be fired later, so we
need to hold a refcnt for net as we do for MPTCP subflows
in mptcp_subflow_create_socket().
[0]:
leaked reference.
sk_alloc (./include/net/net_namespace.h:335 net/core/sock.c:2108)
inet_create (net/ipv4/af_inet.c:319 net/ipv4/af_inet.c:244)
__sock_create (net/socket.c:1546)
smc_create (net/smc/af_smc.c:3269 net/smc/af_smc.c:3284)
__sock_create (net/socket.c:1546)
__sys_socket (net/socket.c:1634 net/socket.c:1618 net/socket.c:1661)
__x64_sys_socket (net/socket.c:1672)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
==================================================================
BUG: KASAN: slab-use-after-free in tcp_write_timer_handler (net/ipv4/tcp_timer.c:378 net/ipv4/tcp_timer.c:624 net/ipv4/tcp_timer.c:594)
Read of size 1 at addr ffff888052b65e0d by task syzrepro/18091
CPU: 0 PID: 18091 Comm: syzrepro Tainted: G W 6.3.0-rc4-01174-gb5d54eb5899a #7
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.amzn2022.0.1 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:107)
print_report (mm/kasan/report.c:320 mm/kasan/report.c:430)
kasan_report (mm/kasan/report.c:538)
tcp_write_timer_handler (net/ipv4/tcp_timer.c:378 net/ipv4/tcp_timer.c:624 net/ipv4/tcp_timer.c:594)
tcp_write_timer (./include/linux/spinlock.h:390 net/ipv4/tcp_timer.c:643)
call_timer_fn (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/timer.h:127 kernel/time/timer.c:1701)
__run_timers.part.0 (kernel/time/timer.c:1752 kernel/time/timer.c:2022)
run_timer_softirq (kernel/time/timer.c:2037)
__do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572)
__irq_exit_rcu (kernel/softirq.c:445 kernel/softirq.c:650)
irq_exit_rcu (kernel/softirq.c:664)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1107 (discriminator 14))
</IRQ>
Fixes: ac7138746e14 ("smc: establish new socket family")
Reported-by: syzbot+7e1e1bdb852961150198@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/000000000000a3f51805f8bcc43a@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
iavf: fix racing in VLANs
Ahmed Zaki says:
This patchset mainly fixes a racing issue in the iavf where the number of
VLANs in the vlan_filter_list might be more than the PF limit. To fix that,
we get rid of the cvlans and svlans bitmaps and keep all the required info
in the list.
The second patch adds two new states that are needed so that we keep the
VLAN info while the interface goes DOWN:
-- DISABLE (notify PF, but keep the filter in the list)
-- INACTIVE (dev is DOWN, filter is removed from PF)
Finally, the current code keeps each state in a separate bit field, which
is error prone. The first patch refactors that by replacing all bits with
a single enum. The changes are minimal where each bit change is replaced
with the new state value.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: remove active_cvlans and active_svlans bitmaps
iavf: refactor VLAN filter states
====================
Link: https://lore.kernel.org/r/20230407210730.3046149-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix not setting Dath Path for broadcast sink
- Fix not cleaning up on LE Connection failure
- SCO: Fix possible circular locking dependency
- L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
- Fix race condition in hidp_session_thread
- btbcm: Fix logic error in forming the board name
- btbcm: Fix use after free in btsdio_remove
* tag 'for-net-2023-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}
Bluetooth: Set ISO Data Path on broadcast sink
Bluetooth: hci_conn: Fix possible UAF
Bluetooth: SCO: Fix possible circular locking dependency sco_sock_getsockopt
Bluetooth: SCO: Fix possible circular locking dependency on sco_connect_cfm
bluetooth: btbcm: Fix logic error in forming the board name.
Bluetooth: btsdio: fix use after free bug in btsdio_remove due to race condition
Bluetooth: Fix race condition in hidp_session_thread
Bluetooth: Fix printing errors if LE Connection times out
Bluetooth: hci_conn: Fix not cleaning up on LE Connection failure
====================
Link: https://lore.kernel.org/r/20230410172718.4067798-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b26cd9325be4c1fcd331b77f10acb627c560d4d7.
This patch introduces a regression on Lenovo Z13, which can't wake
from the lid with it applied; and some unspecified AMD based Dell
platforms are unable to wake from hitting the power button
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230411134932.292287-1-korneld@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The "compatible" doesn't match what the kernel is using. Fix it as
kernel using.
Fixes: 6b2748ada244 ("dt-bindings: interrupt-controller: add yaml for LoongArch CPU interrupt controller")
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20221208020954.GA3368836-robh@kernel.org/
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Liu Peibao <liupeibao@loongson.cn>
Link: https://lore.kernel.org/r/20230401091304.12633-1-liupeibao@loongson.cn
[robh: Rename file to match compatible, fix subject typo]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Provide pci_msix_can_alloc_dyn() stub when CONFIG_PCI_MSI unset to
avoid build errors (Reinette Chatre)
- Quirk AMD XHCI controller that loses MSI-X state in D3hot to avoid
broken USB after hotplug or suspend/resume (Basavaraj Natikar)
- Fix use-after-free in pci_bus_release_domain_nr() (Rob Herring)
* tag 'pci-v6.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix use-after-free in pci_bus_release_domain_nr()
x86/PCI: Add quirk for AMD XHCI controller that loses MSI-X state in D3hot
PCI/MSI: Provide missing stub for pci_msix_can_alloc_dyn()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix fast checksum detection, this affects filesystems with non-crc32c
checksum, calculation would not be offloaded to worker threads
- restore thread_pool mount option behaviour for endio workers, the new
value for maximum active threads would not be set to the actual work
queues
* tag 'for-6.3-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix fast csum implementation detection
btrfs: restore the thread_pool= behavior in remount for the end I/O workqueues
|
|
'priv' is a managed resource, so there is no need to free it explicitly or
there will be a double free().
Fixes: 90ad200b4cbc ("drm/armada: Use devm_drm_dev_alloc")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/c4f3c9207a9fce35cb6dd2cc60e755275961588a.1640536364.git.christophe.jaillet@wanadoo.fr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"Core fix:
- mtdblock: Tolerate corrected bit-flips
Raw NAND fixes:
- meson: Fix bitmask for length in command word
- stm32_fmc2:
- Remove unsupported EDO mode
- Use timings.mode instead of checking tRC_min.
The first patch is the real fix but nowadays we use
timings.mode instead of bare timings, so in order to ease the
backports, the fix was split into two steps, the first one easy
to backport on older kernels, the second one just as a
follow-up so recent stable kernels would look like the
mainline"
* tag 'mtd/fixes-for-6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: meson: fix bitmask for length in command word
mtdblock: tolerate corrected bit-flips
mtd: rawnand: stm32_fmc2: use timings.mode instead of checking tRC_min
mtd: rawnand: stm32_fmc2: remove unsupported EDO mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
- Update my email address in the MAINTAINERS file
* tag 'ata-6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
MAINTAINERS: Change ata maintainer email addresses
|
|
Pull kvm fixes from Paolo Bonzini:
"Two ARM fixes:
- Ensure the guest PMU context is restored before the first KVM_RUN,
fixing an issue where EL0 event counting is broken after vCPU
save/restore
- Actually initialize ID_AA64PFR0_EL1.{CSV2,CSV3} based on the
sanitized, system-wide values for protected VMs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64: Advertise ID_AA64PFR0_EL1.CSV2/3 to protected VMs
KVM: arm64: PMU: Restore the guest's EL0 event counting after migration
|
|
This is an oversight from dc5bdb68b5b3 ("drm/fb-helper: Fix vt
restore") - I failed to realize that nasty userspace could set this.
It's not pretty to mix up kernel-internal and userspace uapi flags
like this, but since the entire fb_var_screeninfo structure is uapi
we'd need to either add a new parameter to the ->fb_set_par callback
and fb_set_par() function, which has a _lot_ of users. Or some other
fairly ugly side-channel int fb_info. Neither is a pretty prospect.
Instead just correct the issue at hand by filtering out this
kernel-internal flag in the ioctl handling code.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Fixes: dc5bdb68b5b3 ("drm/fb-helper: Fix vt restore")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: shlomo@fastmail.com
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Qiujun Huang <hqjagain@gmail.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: linux-fbdev@vger.kernel.org
Cc: Helge Deller <deller@gmx.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Shigeru Yoshida <syoshida@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404193934.472457-1-daniel.vetter@ffwll.ch
|
|
Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/203
Fixes: 5728d064190e1 ("drm/nouveau/fb: handle sysmem flush page from common code")
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405110455.1368428-1-kherbst@redhat.com
|
|
On TGL+ the DSS control registers are at different offsets, and there's
one per pipe. Fix the offsets to fix dual link DSI for TGL+.
There would be helpers for this in the DSC code, but just do the quick
fix now for DSI. Long term, we should probably move all the DSS handling
into intel_vdsc.c, so exporting the helpers seems counter-productive.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8232
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301151409.1581574-1-jani.nikula@intel.com
(cherry picked from commit 1a62dd9895dca78bee28bba3a36f08836fdd143d)
|
|
Change my email address referenced in the MAINTAINERS file for the ata
subsystem to dlemoal@kernel.org. And while at it, also change other
references for zonefs and the k210 drivers to the same address.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull RCU fix from Paul McKenney:
"This fixes a pair of bugs in which an improbable but very real
sequence of events can cause kfree_rcu() to be a bit too quick about
freeing the memory passed to it.
It turns out that this pair of bugs is about two years old, and so
this is not a v6.3 regression. However: (1) It just started showing up
in the wild and (2) Its consequences are dire, so its fix needs to go
in sooner rather than later.
Testing is of course being upgraded, and the upgraded tests detect
this situation very quickly. But to the best of my knowledge right
now, the tests are not particularly urgent and will thus most likely
show up in the v6.5 merge window (the one after this coming one).
Kudos to Ziwei Dai and his group for tracking this one down the hard
way!"
* tag 'urgent-rcu.2023.04.07a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu/kvfree: Avoid freeing new kfree_rcu() memory after old grace period
|
|
Pull virtio fixes from Michael Tsirkin:
"Some last minute fixes - most of them for regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim_net: complete the initialization before register the device
vdpa/mlx5: Add and remove debugfs in setup/teardown driver
tools/virtio: fix typo in README instructions
vhost-scsi: Fix crash during LUN unmapping
vhost-scsi: Fix vhost_scsi struct use after free
virtio-blk: fix ZBD probe in kernels without ZBD support
virtio-blk: fix to match virtio spec
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p fixes from Eric Van Hensbergen:
"These are some collected fixes for the 6.3-rc series that have been
passed our 9p regression tests and been in for-next for at least a
week.
They include a fix for a KASAN reported problem in the extended
attribute handling code and a use after free in the xen transport.
This also includes some updates for the MAINTAINERS file including the
transition of our development mailing list from sourceforge.net to
lists.linux.dev"
* tag '9p-6.3-fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
Update email address and mailing list for v9fs
9p/xen : Fix use after free bug in xen_9pfs_front_remove due to race condition
9P FS: Fix wild-memory-access write in v9fs_get_acl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML fix from Richard Weinberger:
- Build regression fix for older gcc versions
* tag 'uml-for-linus-6.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
um: Only disable SSE on clang to work around old GCC bugs
|
|
Similar to commit d0be8347c623 ("Bluetooth: L2CAP: Fix use-after-free
caused by l2cap_chan_put"), just use l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.
Cc: stable@kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Min Li <lm0963hack@gmail.com>
|
|
This patch enables ISO data rx on broadcast sink.
Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the following trace:
==================================================================
BUG: KASAN: slab-use-after-free in hci_conn_del+0xba/0x3a0
Write of size 8 at addr ffff88800208e9c8 by task iso-tester/31
CPU: 0 PID: 31 Comm: iso-tester Not tainted 6.3.0-rc2-g991aa4a69a47
#4716
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.1-2.fc36
04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x1d/0x70
print_report+0xce/0x610
? __virt_addr_valid+0xd4/0x150
? hci_conn_del+0xba/0x3a0
kasan_report+0xdd/0x110
? hci_conn_del+0xba/0x3a0
hci_conn_del+0xba/0x3a0
hci_conn_hash_flush+0xf2/0x120
hci_dev_close_sync+0x388/0x920
hci_unregister_dev+0x122/0x260
vhci_release+0x4f/0x90
__fput+0x102/0x430
task_work_run+0xf1/0x160
? __pfx_task_work_run+0x10/0x10
? mark_held_locks+0x24/0x90
exit_to_user_mode_prepare+0x170/0x180
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x4e/0x90
entry_SYSCALL_64_after_hwframe+0x70/0xda
Fixes: 0f00cd322d22 ("Bluetooth: Free potentially unfreed SCO connection")
Link: https://syzkaller.appspot.com/bug?extid=8bb72f86fc823817bc5d
Cc: <stable@vger.kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This attempts to fix the following trace:
======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc2-g68fcb3a7bf97 #4706 Not tainted
------------------------------------------------------
sco-tester/31 is trying to acquire lock:
ffff8880025b8070 (&hdev->lock){+.+.}-{3:3}, at:
sco_sock_getsockopt+0x1fc/0xa90
but task is already holding lock:
ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_sock_getsockopt+0x104/0xa90
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
lock_sock_nested+0x32/0x80
sco_connect_cfm+0x118/0x4a0
hci_sync_conn_complete_evt+0x1e6/0x3d0
hci_event_packet+0x55c/0x7c0
hci_rx_work+0x34c/0xa00
process_one_work+0x575/0x910
worker_thread+0x89/0x6f0
kthread+0x14e/0x180
ret_from_fork+0x2b/0x50
-> #1 (hci_cb_list_lock){+.+.}-{3:3}:
__mutex_lock+0x13b/0xcc0
hci_sync_conn_complete_evt+0x1ad/0x3d0
hci_event_packet+0x55c/0x7c0
hci_rx_work+0x34c/0xa00
process_one_work+0x575/0x910
worker_thread+0x89/0x6f0
kthread+0x14e/0x180
ret_from_fork+0x2b/0x50
-> #0 (&hdev->lock){+.+.}-{3:3}:
__lock_acquire+0x18cc/0x3740
lock_acquire+0x151/0x3a0
__mutex_lock+0x13b/0xcc0
sco_sock_getsockopt+0x1fc/0xa90
__sys_getsockopt+0xe9/0x190
__x64_sys_getsockopt+0x5b/0x70
do_syscall_64+0x42/0x90
entry_SYSCALL_64_after_hwframe+0x70/0xda
other info that might help us debug this:
Chain exists of:
&hdev->lock --> hci_cb_list_lock --> sk_lock-AF_BLUETOOTH-BTPROTO_SCO
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
lock(hci_cb_list_lock);
lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
lock(&hdev->lock);
*** DEADLOCK ***
1 lock held by sco-tester/31:
#0: ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0},
at: sco_sock_getsockopt+0x104/0xa90
Fixes: 248733e87d50 ("Bluetooth: Allow querying of supported offload codecs over SCO socket")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This attempts to fix the following trace:
======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc2-g0b93eeba4454 #4703 Not tainted
------------------------------------------------------
kworker/u3:0/46 is trying to acquire lock:
ffff888001fd9130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_connect_cfm+0x118/0x4a0
but task is already holding lock:
ffffffff831e3340 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0x1ad/0x3d0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (hci_cb_list_lock){+.+.}-{3:3}:
__mutex_lock+0x13b/0xcc0
hci_sync_conn_complete_evt+0x1ad/0x3d0
hci_event_packet+0x55c/0x7c0
hci_rx_work+0x34c/0xa00
process_one_work+0x575/0x910
worker_thread+0x89/0x6f0
kthread+0x14e/0x180
ret_from_fork+0x2b/0x50
-> #1 (&hdev->lock){+.+.}-{3:3}:
__mutex_lock+0x13b/0xcc0
sco_sock_connect+0xfc/0x630
__sys_connect+0x197/0x1b0
__x64_sys_connect+0x37/0x50
do_syscall_64+0x42/0x90
entry_SYSCALL_64_after_hwframe+0x70/0xda
-> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
__lock_acquire+0x18cc/0x3740
lock_acquire+0x151/0x3a0
lock_sock_nested+0x32/0x80
sco_connect_cfm+0x118/0x4a0
hci_sync_conn_complete_evt+0x1e6/0x3d0
hci_event_packet+0x55c/0x7c0
hci_rx_work+0x34c/0xa00
process_one_work+0x575/0x910
worker_thread+0x89/0x6f0
kthread+0x14e/0x180
ret_from_fork+0x2b/0x50
other info that might help us debug this:
Chain exists of:
sk_lock-AF_BLUETOOTH-BTPROTO_SCO --> &hdev->lock --> hci_cb_list_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hci_cb_list_lock);
lock(&hdev->lock);
lock(hci_cb_list_lock);
lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
*** DEADLOCK ***
4 locks held by kworker/u3:0/46:
#0: ffff8880028d1130 ((wq_completion)hci0#2){+.+.}-{0:0}, at:
process_one_work+0x4c0/0x910
#1: ffff8880013dfde0 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0},
at: process_one_work+0x4c0/0x910
#2: ffff8880025d8070 (&hdev->lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0xa6/0x3d0
#3: ffffffffb79e3340 (hci_cb_list_lock){+.+.}-{3:3}, at:
hci_sync_conn_complete_evt+0x1ad/0x3d0
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch fixes an incorrect loop exit condition in code that replaces
'/' symbols in the board name. There might also be a memory corruption
issue here, but it is unlikely to be a real problem.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In btsdio_probe, the data->work is bound with btsdio_work. It will be
started in btsdio_send_frame.
If the btsdio_remove runs with a unfinished work, there may be a race
condition that hdev is freed but used in btsdio_work. Fix it by
canceling the work before do cleanup in btsdio_remove.
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There is a potential race condition in hidp_session_thread that may
lead to use-after-free. For instance, the timer is active while
hidp_del_timer is called in hidp_session_thread(). After hidp_session_put,
then 'session' will be freed, causing kernel panic when hidp_idle_timeout
is running.
The solution is to use del_timer_sync instead of del_timer.
Here is the call trace:
? hidp_session_probe+0x780/0x780
call_timer_fn+0x2d/0x1e0
__run_timers.part.0+0x569/0x940
hidp_session_probe+0x780/0x780
call_timer_fn+0x1e0/0x1e0
ktime_get+0x5c/0xf0
lapic_next_deadline+0x2c/0x40
clockevents_program_event+0x205/0x320
run_timer_softirq+0xa9/0x1b0
__do_softirq+0x1b9/0x641
__irq_exit_rcu+0xdc/0x190
irq_exit_rcu+0xe/0x20
sysvec_apic_timer_interrupt+0xa1/0xc0
Cc: stable@vger.kernel.org
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:
Bluetooth: hci0: Opcode 0x200d failed: -110
Bluetooth: hci0: request failed to create LE connection: err -110
Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.
Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60de ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_connect_le_scan_cleanup shall always be invoked to cleanup the
states and re-enable passive scanning if necessary, otherwise it may
cause the pending action to stay active causing multiple attempts to
connect.
Fixes: 9b3628d79b46 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Fix "same task" check when redirecting event output
- Do not wait unconditionally for RCU on the event migration path if
there are no events to migrate
* tag 'perf_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix the same task check in perf_event_set_output
perf: Optimize perf_pmu_migrate_context()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a new Intel Arrow Lake CPU model number
- Fix a confusion about how to check the version of the ACPI spec which
supports a "online capable" bit in the MADT table which lead to a
bunch of boot breakages with Zen1 systems and VMs
* tag 'x86_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add model number for Intel Arrow Lake processor
x86/acpi/boot: Correct acpi_is_processor_usable() check
x86/ACPI/boot: Use FADT version to check support for online capable
|