| Age | Commit message (Collapse) | Author |
|---|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the capability to map non-linear xdp frames in XDP_TX and
ndo_xdp_xmit callback.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817173628.109102-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Petr Machata says:
====================
selftests: mlxsw: Add ordering tests for unified bridge model
Amit Cohen writes:
Commit 798661c73672 ("Merge branch 'mlxsw-unified-bridge-conversion-part-6'")
converted mlxsw driver to use unified bridge model. In the legacy model,
when a RIF was created / destroyed, it was firmware's responsibility to
update it in the relevant FID classification records. In the unified bridge
model, this responsibility moved to software.
This set adds tests to check the order of configuration for the following
classifications:
1. {Port, VID} -> FID
2. VID -> FID
3. VNI -> FID (after decapsulation)
In addition, in the legacy model, software is responsible to update a
table which is used to determine the packet's egress VID. Add a test to
check that the order of configuration does not impact switch behavior.
See more details in the commit messages.
Note that the tests supposed to pass also using the legacy model, they
are added now as with the new model they test the driver and not the
firmware.
Patch set overview:
Patch #1 adds test for {Port, VID} -> FID
Patch #2 adds test for VID -> FID
Patch #3 adds test for VNI -> FID
Patch #4 adds test for egress VID classification
====================
Link: https://lore.kernel.org/r/cover.1660747162.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via
REIV register.
The table needs to be updated in the following flows:
1. When a RIF is set on a FID, for each FID's {Port, VID} mapping, a new
{RIF, Port}->VID mapping should be created.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
a new {RIF, Port}->VID mapping should be created.
Add a test to verify that packets get the correct VID after routing,
regardless of the order of the configuration.
# ./egress_vid_classification.sh
TEST: Add RIF for existing {port, VID}->FID mapping [ OK ]
TEST: Add {port, VID}->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VXLAN decapsulation, the FID classification is done according to the
VNI. When a RIF is added on top of a FID, the existing VNI->FID mapping
should be updated by the software with the new RIF. In addition, when a new
mapping is added for FID which already has a RIF, the correct RIF should
be used for it.
Add a test to verify that packets can be routed after decapsulation which
is done after VNI->FID classification, regardless of the order of the
configuration.
# ./ingress_rif_conf_vxlan.sh
TEST: Add RIF for existing VNI->FID mapping [ OK ]
TEST: Add VNI->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VLAN-aware bridges (802.1Q), the FID classification is done according
to VID. When a RIF is added on top of a FID, the existing VID->FID mapping
should be updated by the software with the new RIF.
We never map multiple VLANs to the same FID using VID->FID, so we cannot
create VID->FID for FID which already has a RIF using 802.1Q. Anyway,
verify that packets can be routed via port which is added after the FID
already has a RIF.
Add a test to verify that packets can be routed after VID->FID
classification, regardless of the order of the configuration.
# ./ingress_rif_conf_1q.sh
TEST: Add RIF for existing VID->FID mapping [ OK ]
TEST: Add port to VID->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before layer 2 forwarding, the device classifies an incoming packet to a
FID. After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that needs
to be routed will ingress the router block.
For VLAN-unaware bridges (802.1D), the FID classification is done according
to {Port, VID}. When a RIF is added on top of a FID, all the existing
{Port, VID}->FID mappings should be updated by the software with the new
RIF. In addition, when a new mapping is added for FID which already has a
RIF, the correct RIF should be used for it.
Add a test to verify that packets can be routed after {Port, VID}->FID
classification, regardless of the order of the configuration.
# ./ingress_rif_conf_1d.sh
TEST: Add RIF for existing {port, VID}->FID mapping [ OK ]
TEST: Add {port, VID}->FID mapping for FID with a RIF [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mtk_xdp_submit_frame
Get rid of unnecessary txd_pdma pointer in mtk_xdp_submit_frame for loop
since it is actually used at the end of the routine using latest mtk_tx_dma
consumed pointer as reference.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/2c40b0fbb9163a0d62ff897abae17db84a9f3b99.1660669138.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Expose MACSEC_SALT_LEN definition to user space to be
used in various user space applications such as iproute.
Iproute will use this as part of adding macsec extended
packet number support.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Link: https://lore.kernel.org/r/20220818153229.4721-1-ehakim@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter.
Current release - regressions:
- tcp: fix cleanup and leaks in tcp_read_skb() (the new way BPF
socket maps get data out of the TCP stack)
- tls: rx: react to strparser initialization errors
- netfilter: nf_tables: fix scheduling-while-atomic splat
- net: fix suspicious RCU usage in bpf_sk_reuseport_detach()
Current release - new code bugs:
- mlxsw: ptp: fix a couple of races, static checker warnings and
error handling
Previous releases - regressions:
- netfilter:
- nf_tables: fix possible module reference underflow in error path
- make conntrack helpers deal with BIG TCP (skbs > 64kB)
- nfnetlink: re-enable conntrack expectation events
- net: fix potential refcount leak in ndisc_router_discovery()
Previous releases - always broken:
- sched: cls_route: disallow handle of 0
- neigh: fix possible local DoS due to net iface start/stop loop
- rtnetlink: fix module refcount leak in rtnetlink_rcv_msg
- sched: fix adding qlen to qcpu->backlog in gnet_stats_add_queue_cpu
- virtio_net: fix endian-ness for RSS
- dsa: mv88e6060: prevent crash on an unused port
- fec: fix timer capture timing in `fec_ptp_enable_pps()`
- ocelot: stats: fix races, integer wrapping and reading incorrect
registers (the change of register definitions here accounts for
bulk of the changed LoC in this PR)"
* tag 'net-6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
net: moxa: MAC address reading, generating, validity checking
tcp: handle pure FIN case correctly
tcp: refactor tcp_read_skb() a bit
tcp: fix tcp_cleanup_rbuf() for tcp_read_skb()
tcp: fix sock skb accounting in tcp_read_skb()
igb: Add lock to avoid data race
dt-bindings: Fix incorrect "the the" corrections
net: genl: fix error path memory leak in policy dumping
stmmac: intel: Add a missing clk_disable_unprepare() call in intel_eth_pci_remove()
net: ethernet: mtk_eth_soc: fix possible NULL pointer dereference in mtk_xdp_run
net/mlx5e: Allocate flow steering storage during uplink initialization
net: mscc: ocelot: report ndo_get_stats64 from the wraparound-resistant ocelot->stats
net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset
net: mscc: ocelot: make struct ocelot_stat_layout array indexable
net: mscc: ocelot: fix race between ndo_get_stats64 and ocelot_check_stats_work
net: mscc: ocelot: turn stats_lock into a spinlock
net: mscc: ocelot: fix address of SYS_COUNT_TX_AGING counter
net: mscc: ocelot: fix incorrect ndo_get_stats64 packet counters
net: dsa: felix: fix ethtool 256-511 and 512-1023 TX packet counters
net: dsa: don't warn in dsa_port_set_state_now() when driver doesn't support it
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fix from Shuah Khan:
- fix landlock test build regression
* tag 'linux-kselftest-next-6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/landlock: fix broken include of linux/landlock.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull rtla tool fixes from Steven Rostedt:
"Fixes for the Real-Time Linux Analysis tooling:
- Fix tracer name in comments and prints
- Fix setting up symlinks
- Allow extra flags to be set in build
- Consolidate and show all necessary libraries not found in build
error"
* tag 'trace-rtla-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
rtla: Consolidate and show all necessary libraries that failed for building
tools/rtla: Build with EXTRA_{C,LD}FLAGS
tools/rtla: Fix command symlinks
rtla: Fix tracer name
|
|
Some (Juniper MX5) SFP link partners exhibit a disinclination to
autonegotiate with X550 configured in SFI mode. This patch enables
a manual AN-37 restart to work around the problem.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Wei Fang says:
====================
Add DT property to disable hibernation mode
The patches add the ability to disable the hibernation mode of AR803x
PHYs. Hibernation mode defaults to enabled after hardware reset on
these PHYs. If the AR803x PHYs enter hibernation mode, they will not
provide any clock. For some MACs, they might need the clocks which
provided by the PHYs to support their own hardware logic.
So, the patches add the support to disable hibernation mode by adding
a boolean:
qca,disable-hibernation-mode
If one wished to disable hibernation mode to better match with the
specifical MAC, just add this property in the phy node of DT.
====================
Link: https://lore.kernel.org/r/20220818030054.1010660-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the cable is unplugged, the Atheros AR803x PHYs will enter
hibernation mode after about 10 seconds if the hibernation mode
is enabled and will not provide any clock to the MAC. But for
some MACs, this feature might cause unexpected issues due to the
logic of MACs.
Taking SYNP MAC (stmmac) as an example, if the cable is unplugged
and the "eth0" interface is down, the AR803x PHY will enter
hibernation mode. Then perform the "ifconfig eth0 up" operation,
the stmmac can't be able to complete the software reset operation
and fail to init it's own DMA. Therefore, the "eth0" interface is
failed to ifconfig up. Why does it cause this issue? The truth is
that the software reset operation of the stmmac is designed to
depend on the RX_CLK of PHY.
So, this patch offers an option for the user to determine whether
to disable the hibernation mode of AR803x PHYs.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hibernation mode of Atheros AR803x PHYs defaults to be
enabled after hardware reset. When the cable is unplugged,
the PHY will enter hibernation mode after about 10 seconds
and the PHY clocks will be stopped to save power.
However, some MACs need the phy output clock for proper
functioning of their logic. For instance, stmmac needs the
RX_CLK of PHY for software reset to complete.
Therefore, add a DT property to configure the PHY to disable
this hardware hibernation mode.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This device does not remember its MAC address, so add a possibility
to get it from the platform. If it fails, generate a random address.
This will provide a MAC address early during boot without user space
being involved.
Also remove extra calls to is_valid_ether_addr().
Made after suggestions by Andrew Lunn:
1) Use eth_hw_addr_random() to assign a random MAC address during probe.
2) Remove is_valid_ether_addr() from moxart_mac_open()
3) Add a call to platform_get_ethdev_address() during probe
4) Remove is_valid_ether_addr() from moxart_set_mac_address(). The core does this
v1 -> v2:
Handle EPROBE_DEFER returned from platform_get_ethdev_address().
Move MAC reading code to the beginning of the probe function.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Yang Yingliang <yangyingliang@huawei.com>
CC: Pavel Skripkin <paskripkin@gmail.com>
CC: Guobin Huang <huangguobin4@huawei.com>
CC: Yang Wei <yang.wei9@zte.com.cn>
CC: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220818092317.529557-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cong Wang says:
====================
tcp: some bug fixes for tcp_read_skb()
This patchset contains 3 bug fixes and 1 minor refactor patch for
tcp_read_skb(). V1 only had the first patch, as Eric prefers to fix all
of them together, I have to group them together.
====================
Link: https://lore.kernel.org/r/20220817195445.151609-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When skb->len==0, the recv_actor() returns 0 too, but we also use 0
for error conditions. This patch amends this by propagating the errors
to tcp_read_skb() so that we can distinguish skb->len==0 case from
error cases.
Fixes: 04919bed948d ("tcp: Introduce tcp_read_skb()")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As tcp_read_skb() only reads one skb at a time, the while loop is
unnecessary, we can turn it into an if. This also simplifies the
code logic.
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_cleanup_rbuf() retrieves the skb from sk_receive_queue, it
assumes the skb is not yet dequeued. This is no longer true for
tcp_read_skb() case where we dequeue the skb first.
Fix this by introducing a helper __tcp_cleanup_rbuf() which does
not require any skb and calling it in tcp_read_skb().
Fixes: 04919bed948d ("tcp: Introduce tcp_read_skb()")
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before commit 965b57b469a5 ("net: Introduce a new proto_ops
->read_skb()"), skb was not dequeued from receive queue hence
when we close TCP socket skb can be just flushed synchronously.
After this commit, we have to uncharge skb immediately after being
dequeued, otherwise it is still charged in the original sock. And we
still need to retain skb->sk, as eBPF programs may extract sock
information from skb->sk. Therefore, we have to call
skb_set_owner_sk_safe() here.
Fixes: 965b57b469a5 ("net: Introduce a new proto_ops ->read_skb()")
Reported-and-tested-by: syzbot+a0e6f8738b58f7654417@syzkaller.appspotmail.com
Tested-by: Stanislav Fomichev <sdf@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit c23d92b80e0b ("igb: Teardown SR-IOV before
unregister_netdev()") places the unregister_netdev() call after the
igb_disable_sriov() call to avoid functionality issue.
However, it introduces several race conditions when detaching a device.
For example, when .remove() is called, the below interleaving leads to
use-after-free.
(FREE from device detaching) | (USE from netdev core)
igb_remove | igb_ndo_get_vf_config
igb_disable_sriov | vf >= adapter->vfs_allocated_count?
kfree(adapter->vf_data) |
adapter->vfs_allocated_count = 0 |
| memcpy(... adapter->vf_data[vf]
Moreover, the igb_disable_sriov() also suffers from data race with the
requests from VF driver.
(FREE from device detaching) | (USE from requests)
igb_remove | igb_msix_other
igb_disable_sriov | igb_msg_task
kfree(adapter->vf_data) | vf < adapter->vfs_allocated_count
adapter->vfs_allocated_count = 0 |
To this end, this commit first eliminates the data races from netdev
core by using rtnl_lock (similar to commit 719479230893 ("dpaa2-eth: add
MAC/PHY support through phylink")). And then adds a spinlock to
eliminate races from driver requests. (similar to commit 1e53834ce541
("ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero")
Fixes: c23d92b80e0b ("igb: Teardown SR-IOV before unregister_netdev()")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817184921.735244-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-17 (ice)
This series contains updates to ice driver only.
Grzegorz prevents modifications to VLAN 0 when setting VLAN promiscuous
as it will already be set. He also ignores -EEXIST error when attempting
to set promiscuous and ensures promiscuous mode is properly cleared from
the hardware when being removed.
Benjamin ignores additional -EEXIST errors when setting promiscuous mode
since the existing mode is the desired mode.
Sylwester fixes VFs to allow sending of tagged traffic when no VLAN filters
exist.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix VF not able to send tagged traffic with no VLAN filters
ice: Ignore error message when setting same promiscuous mode
ice: Fix clearing of promisc mode with bridge over bond
ice: Ignore EEXIST when setting promisc mode
ice: Fix double VLAN error when entering promisc mode
====================
Link: https://lore.kernel.org/r/20220817171329.65285-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Lots of double occurrences of "the" were replaced by single occurrences,
but some of them should become "to the" instead.
Fixes: 12e5bde18d7f6ca4 ("dt-bindings: Fix typo in comment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c5743c0a1a24b3a8893797b52fed88b99e56b04b.1660755148.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the ethtool_op_get_ts_info() callback to ethtool ops, so that we can
at least use software timestamping.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/20220817095725.97444-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If construction of the array of policies fails when recording
non-first policy we need to unwind.
netlink_policy_dump_add_policy() itself also needs fixing as
it currently gives up on error without recording the allocated
pointer in the pstate pointer.
Reported-by: syzbot+dc54d9ba8153b216cae0@syzkaller.appspotmail.com
Fixes: 50a896cf2d6f ("genetlink: properly support per-op policy dumping")
Link: https://lore.kernel.org/r/20220816161939.577583-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
intel_eth_pci_remove()
Commit 09f012e64e4b ("stmmac: intel: Fix clock handling on error and remove
paths") removed this clk_disable_unprepare()
This was partly revert by commit ac322f86b56c ("net: stmmac: Fix clock
handling on remove path") which removed this clk_disable_unprepare()
because:
"
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
"
However later on, commit 5ec55823438e8 ("net: stmmac: add clocks management
for gmac driver") has updated stmmac_dvr_remove() which do not call
clk_disable_unprepare() anymore.
So this call should now be called from intel_eth_pci_remove().
Fixes: 5ec55823438e8 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/d7c8c1dadf40df3a7c9e643f76ffadd0ccc1ad1b.1660659689.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With special lengths supplied by user space, register_shm_helper() has
an integer overflow when calculating the number of pages covered by a
supplied user space memory region.
This causes internal_get_user_pages_fast() a helper function of
pin_user_pages_fast() to do a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Modules linked in:
CPU: 1 PID: 173 Comm: optee_example_a Not tainted 5.19.0 #11
Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
pc : internal_get_user_pages_fast+0x474/0xa80
Call trace:
internal_get_user_pages_fast+0x474/0xa80
pin_user_pages_fast+0x24/0x4c
register_shm_helper+0x194/0x330
tee_shm_register_user_buf+0x78/0x120
tee_ioctl+0xd0/0x11a0
__arm64_sys_ioctl+0xa8/0xec
invoke_syscall+0x48/0x114
Fix this by adding an an explicit call to access_ok() in
tee_shm_register_user_buf() to catch an invalid user space address
early.
Fixes: 033ddf12bcf5 ("tee: add register user memory")
Cc: stable@vger.kernel.org
Reported-by: Nimish Mishra <neelam.nimish@gmail.com>
Reported-by: Anirban Chakraborty <ch.anirban00727@gmail.com>
Reported-by: Debdeep Mukhopadhyay <debdeep.mukhopadhyay@gmail.com>
Suggested-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pages allocated with GFP_ATOMIC cannot come from Highmem. This is why
there is no need to call kmap() on them.
Therefore, don't call kmap() on rx_buffer->page() and instead use a
plain page_address() to get the kernel address.
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove non-inclusive language from the driver where
possible; replace "master" with "primary"; replace
"slave" with "secondary".
Signed-off-by: Mikael Barsehyan <mikael.barsehyan@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove ucast_shared as it was always true. Remove the code depending on
ucast_shared from ice_add_mac and ice_remove_mac.
Remove ice_find_ucast_rule_entry function as it was only
used when ucast_shared was set to false.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For certain devices, 100M speeds are supported. Do not mask off
100M speed for these devices.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Co-developed-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Mikael Barsehyan <mikael.barsehyan@intel.com>
Tested-by: Kavya AV <kavyax.av@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make sure that only the valid combinations of FCS/CRC stripping and
VLAN stripping offloads are allowed.
You cannot have FCS/CRC stripping disabled while VLAN stripping is
enabled - this breaks the correctness of the FCS/CRC.
If administrator tries to enable VLAN stripping when FCS/CRC stripping is
disabled, the request should be rejected.
If administrator tries to disable FCS/CRC stripping when VLAN stripping
is enabled, the request should be rejected if VLANs are configured. If
there is no VLAN configured, then both FCS/CRC and VLAN stripping should
be disabled.
Testing Hints:
The default settings after driver load are:
- VLAN C-Tag offloads are enabled
- VLAN S-Tag offloads are disabled
- FCS/CRC stripping is enabled
Restore the default settings before each test with the command:
ethtool -K eth0 rx-fcs off rxvlan on txvlan on rx-vlan-stag-hw-parse off
tx-vlan-stag-hw-insert off
Test 1:
Disable FCS/CRC and VLAN stripping:
ethtool -K eth0 rx-fcs on rxvlan off
Try to enable VLAN stripping:
ethtool -K eth0 rxvlan on
Expected: VLAN stripping request is rejected
Test 2:
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: VLAN stripping is also disabled, as there are no VLAN
configured
Test 3:
Add a VLAN:
ip link add link eth0 eth0.42 type vlan id 42
ip link set eth0 up
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: FCS/CRC stripping request is rejected
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver can allow the user to configure whether the CRC aka the FCS
(Frame Check Sequence) is DMA'd to the host as part of the receive
buffer. The driver usually wants this feature disabled so that the
hardware checks the FCS and strips it in order to save PCI bandwidth.
Control the reception of FCS to the host using the command:
ethtool -K eth0 rx-fcs <on|off>
The default shown in ethtool -k eth0 | grep fcs; should be "off", as the
hardware will drop any frame with a bad checksum, and DMA of the
checksum is useless overhead especially for small packets.
Testing Hints:
test the FCS/CRC arrives with received packets using
tcpdump -nnpi eth0 -xxxx
and it should show crc data as the last 4 bytes of the packet. Can also
use wireshark to turn on CRC checking and check the data is correct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix possible NULL pointer dereference in mtk_xdp_run() if the
ebpf program returns XDP_TX and xdp_convert_buff_to_frame routine fails
returning NULL.
Fixes: 5886d26fd25bb ("net: ethernet: mtk_eth_soc: add xmit XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/627a07d759020356b64473e09f0855960e02db28.1660659112.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPsec code relies on valid priv->fs pointer that is the case in NIC
flow, but not correct in uplink. Before commit that mentioned in the
Fixes line, that pointer was valid in all flows as it was allocated
together with priv struct.
In addition, the cleanup representors routine called to that
not-initialized priv->fs pointer and its internals which caused NULL
deference.
So, move FS allocation to be as early as possible.
Fixes: af8bbf730068 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/ae46fa5bed3c67f937bfdfc0370101278f5422f1.1660639564.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Fixes for Ocelot driver statistics
This series contains bug fixes for the ocelot drivers (both switchdev
and DSA). Some concern the counters exposed to ethtool -S, and others to
the counters exposed to ifconfig. I'm aware that the changes are fairly
large, but I wanted to prioritize on a proper approach to addressing the
issues rather than a quick hack.
Some of the noticed problems:
- bad register offsets for some counters
- unhandled concurrency leading to corrupted counters
- unhandled 32-bit wraparound of ifconfig counters
The issues on the ocelot switchdev driver were noticed through code
inspection, I do not have the hardware to test.
This patch set necessarily converts ocelot->stats_lock from a mutex to a
spinlock. I know this affects Colin Foster's development with the SPI
controlled VSC7512. I have other changes prepared for net-next that
convert this back into a mutex (along with other changes in this area).
====================
Link: https://lore.kernel.org/r/20220816135352.1431497-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot->stats
Rather than reading the stats64 counters directly from the 32-bit
hardware, it's better to rely on the output produced by the periodic
ocelot_port_update_stats().
It would be even better to call ocelot_port_update_stats() right from
ocelot_get_stats64() to make sure we report the current values rather
than the ones from 2 seconds ago. But we need to export
ocelot_port_update_stats() from the switch lib towards the switchdev
driver for that, and future work will largely undo that.
There are more ocelot-based drivers waiting to be introduced, an example
of which is the SPI-controlled VSC7512. In that driver's case, it will
be impossible to call ocelot_port_update_stats() from ndo_get_stats64
context, since the latter is atomic, and reading the stats over SPI is
sleepable. So the compromise taken here, which will also hold going
forward, is to report 64-bit counters to stats64, which are not 100% up
to date.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 2 methods can run concurrently, and one will change the window of
counters (SYS_STAT_CFG_STAT_VIEW) that the other sees. The fix is
similar to what commit 7fbf6795d127 ("net: mscc: ocelot: fix mutex lock
error during ethtool stats read") has done for ethtool -S.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This register, used as part of stats->tx_dropped in
ocelot_get_stats64(), has a wrong address. At the address currently
given, there is actually the c_tx_green_prio_6 counter.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc16552 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ds->ops->port_stp_state_set() is, like most DSA methods, optional, and
if absent, the port is supposed to remain in the forwarding state (as
standalone). Such is the case with the mv88e6060 driver, which does not
offload the bridge layer. DSA warns that the STP state can't be changed
to FORWARDING as part of dsa_port_enable_rt(), when in fact it should not.
The error message is also not up to modern standards, so take the
opportunity to make it more descriptive.
Fixes: fd3645413197 ("net: dsa: change scope of STP state setter")
Reported-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20220816201445.1809483-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If an error occurs in dsa_devlink_region_create(), then 'priv->regions'
array will be accessed by negative index '-1'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: bf425b82059e ("net: dsa: sja1105: expose static config as devlink region")
Link: https://lore.kernel.org/r/20220817003845.389644-1-subkhankulov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 'has_crossts' flag was not used anywhere in the stmmac driver,
removing it from both header file and dwmac-intel driver.
Signed-off-by: Wong Vee Khee <veekhee@apple.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20220817064324.10025-1-veekhee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Andrii Nakryiko says:
====================
bpf-next 2022-08-17
We've added 45 non-merge commits during the last 14 day(s) which contain
a total of 61 files changed, 986 insertions(+), 372 deletions(-).
The main changes are:
1) New bpf_ktime_get_tai_ns() BPF helper to access CLOCK_TAI, from Kurt
Kanzenbach and Jesper Dangaard Brouer.
2) Few clean ups and improvements for libbpf 1.0, from Andrii Nakryiko.
3) Expose crash_kexec() as kfunc for BPF programs, from Artem Savkov.
4) Add ability to define sleepable-only kfuncs, from Benjamin Tissoires.
5) Teach libbpf's bpf_prog_load() and bpf_map_create() to gracefully handle
unsupported names on old kernels, from Hangbin Liu.
6) Allow opting out from auto-attaching BPF programs by libbpf's BPF skeleton,
from Hao Luo.
7) Relax libbpf's requirement for shared libs to be marked executable, from
Henqgi Chen.
8) Improve bpf_iter internals handling of error returns, from Hao Luo.
9) Few accommodations in libbpf to support GCC-BPF quirks, from James Hilliard.
10) Fix BPF verifier logic around tracking dynptr ref_obj_id, from Joanne Koong.
11) bpftool improvements to handle full BPF program names better, from Manu
Bretelle.
12) bpftool fixes around libcap use, from Quentin Monnet.
13) BPF map internals clean ups and improvements around memory allocations,
from Yafang Shao.
14) Allow to use cgroup_get_from_file() on cgroupv1, allowing BPF cgroup
iterator to work on cgroupv1, from Yosry Ahmed.
15) BPF verifier internal clean ups, from Dave Marchevsky and Joanne Koong.
16) Various fixes and clean ups for selftests/bpf and vmtest.sh, from Daniel
Xu, Artem Savkov, Joanne Koong, Andrii Nakryiko, Shibin Koikkara Reeny.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (45 commits)
selftests/bpf: Few fixes for selftests/bpf built in release mode
libbpf: Clean up deprecated and legacy aliases
libbpf: Streamline bpf_attr and perf_event_attr initialization
libbpf: Fix potential NULL dereference when parsing ELF
selftests/bpf: Tests libbpf autoattach APIs
libbpf: Allows disabling auto attach
selftests/bpf: Fix attach point for non-x86 arches in test_progs/lsm
libbpf: Making bpf_prog_load() ignore name if kernel doesn't support
selftests/bpf: Update CI kconfig
selftests/bpf: Add connmark read test
selftests/bpf: Add existing connection bpf_*_ct_lookup() test
bpftool: Clear errno after libcap's checks
bpf: Clear up confusion in bpf_skb_adjust_room()'s documentation
bpftool: Fix a typo in a comment
libbpf: Add names for auxiliary maps
bpf: Use bpf_map_area_alloc consistently on bpf map creation
bpf: Make __GFP_NOWARN consistent in bpf map creation
bpf: Use bpf_map_area_free instread of kvfree
bpf: Remove unneeded memset in queue_stack_map creation
libbpf: preserve errno across pr_warn/pr_info/pr_debug
...
====================
Link: https://lore.kernel.org/r/20220817215656.1180215-1-andrii@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
