summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-08-03ionic: separate interrupt for Tx and RxShannon Nelson
Add the capability to split the Tx queues onto their own interrupts with their own napi contexts. This gives the opportunity for more direct control of Tx interrupt handling, such as CPU affinity and interrupt coalescing, useful for some traffic loads. v2: use ethtool -L, not a vendor specific priv-flag v3: simplify logging, drop unnecessary "no-change" tests Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03ionic: tx separate servicingShannon Nelson
We give the tx clean path its own budget and service routine in order to give a little more leeway to be more aggressive, and in preparation for coming changes. We've found this gives us a little better performance in some packet processing scenarios without hurting other scenarios. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03ionic: use fewer firmware doorbells on rx fillShannon Nelson
We really don't need to hit the Rx queue doorbell so many times, we can wait to the end and cause a little less thrash. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: gre: recompute gre csum for sctp over gre tunnelsLorenzo Bianconi
The GRE tunnel can be used to transport traffic that does not rely on a Internet checksum (e.g. SCTP). The issue can be triggered creating a GRE or GRETAP tunnel and transmitting SCTP traffic ontop of it where CRC offload has been disabled. In order to fix the issue we need to recompute the GRE csum in gre_gso_segment() not relying on the inner checksum. The issue is still present when we have the CRC offload enabled. In this case we need to disable the CRC offload if we require GRE checksum since otherwise skb_checksum() will report a wrong value. Fixes: 90017accff61 ("sctp: Add GSO support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: bridge: clear bridge's private skb space on xmitNikolay Aleksandrov
We need to clear all of the bridge private skb variables as they can be stale due to the packet being recirculated through the stack and then transmitted through the bridge device. Similar memset is already done on bridge's input. We've seen cases where proxyarp_replied was 1 on routed multicast packets transmitted through the bridge to ports with neigh suppress which were getting dropped. Same thing can in theory happen with the port isolation bit as well. Fixes: 821f1b21cabb ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03ipv6/addrconf: use a boolean to choose between UNREGISTER/DOWNFlorent Fourcot
"how" was used as a boolean. Change the type to bool, and improve variable name Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03ipv6/addrconf: call addrconf_ifdown with consistent valuesFlorent Fourcot
Second parameter of addrconf_ifdown "how" is used as a boolean internally. It does not make sense to call it with something different of 0 or 1. This value is set to 2 in all git history. Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03Merge branch 'net-openvswitch-masks-cache-enhancements'David S. Miller
Eelco Chaudron says: ==================== net: openvswitch: masks cache enhancements This patchset adds two enhancements to the Open vSwitch masks cache. Changes in v4 [patch 2/2 only]: - Remove null check before calling free_percpu() - Make ovs_dp_change() return appropriate error codes Changes in v3 [patch 2/2 only]: - Use is_power_of_2() function - Use array_size() function - Fix remaining sparse errors Changes in v2 [patch 2/2 only]: - Fix sparse warnings - Fix netlink policy items reported by Florian Westphal ==================== Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: openvswitch: make masks cache size configurableEelco Chaudron
This patch makes the masks cache size configurable, or with a size of 0, disable it. Reviewed-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: openvswitch: add masks cache hit counterEelco Chaudron
Add a counter that counts the number of masks cache hits, and export it through the megaflow netlink statistics. Reviewed-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Signed-off-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mvpp2: fix memory leak in mvpp2_rxLorenzo Bianconi
Release skb memory in mvpp2_rx() if mvpp2_rx_refill routine fails Fixes: b5015854674b ("net: mvpp2: fix refilling BM pools in RX path") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Matteo Croce <mcroce@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03ethtool: ethnl_set_linkmodes: remove redundant null checkGaurav Singh
info cannot be NULL here since its being accessed earlier in the function: nlmsg_parse(info->nlhdr...). Remove this redundant NULL check. Signed-off-by: Gaurav Singh <gaurav1086@gmail.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03openvswitch: Prevent kernel-infoleak in ovs_ct_put_key()Peilin Ye
ovs_ct_put_key() is potentially copying uninitialized kernel stack memory into socket buffers, since the compiler may leave a 3-byte hole at the end of `struct ovs_key_ct_tuple_ipv4` and `struct ovs_key_ct_tuple_ipv6`. Fix it by initializing `orig` with memset(). Fixes: 9dd7f8907c37 ("openvswitch: Add original direction conntrack tuple to sw_flow_key.") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net/sched: act_ct: fix miss set mru for ovs after defrag in act_ctwenxu
When openvswitch conntrack offload with act_ct action. Fragment packets defrag in the ingress tc act_ct action and miss the next chain. Then the packet pass to the openvswitch datapath without the mru. The over mtu packet will be dropped in output action in openvswitch for over mtu. "kernel: net2: dropped over-mtu packet: 1528 > 1500" This patch add mru in the tc_skb_ext for adefrag and miss next chain situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru to the qdisc_skb_cb when the packet defrag. And When the chain miss, The mru is set to tc_skb_ext which can be got by ovs datapath. Fixes: b57dc7c13ea9 ("net/sched: Introduce action ct") Signed-off-by: wenxu <wenxu@ucloud.cn> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03Merge branch 'Improve-MDIO-Ethernet-PHY-reset'David S. Miller
Bruno Thomsen says: ==================== Improve MDIO Ethernet PHY reset This patch series is a result of trying to upstream a new device tree for a TQMa7D based board[1][2]. Initial this DTS used some deprecated PHY reset properties on the FEC device; NXP Ethernet MAC also known as Freescale Fast Ethernet Controller. When switching from FEC properties[3]: "phy-reset-gpios" "phy-reset-duration" "phy-reset-post-delay" To MDIO PHY properties[4]: "reset-gpios" "reset-assert-us" "reset-deassert-us" The result was that no Ethernet PHY device was detected on boot. This issue could be worked around by disabling PHY type ID auto- detection by using "ethernet-phy-id0022.1560" as compatible string and not "ethernet-phy-ieee802.3-c22". Upstreaming a DTS with this workaround was not accepted, so I digged into the MDIO reset flow and found that it had a few missing parts compared to the deprecated FEC reset function. After some more testing and logic analyzer traces it was revealed that the failed PHY communication was due to missing initial device reset. I was suggested[5] in a earlier mail thread to use MDIO bus reset as that was performed before auto-detection, but current device tree binding was limited to reset assert in usec. Microchip/Micrel Ethernet PHYs recommended reset circuit[8], figure 7-12, is a little "slow" after reset deassert as that is left to a RC circuit with a tau of ~100ms; using a 10k PU resistor together with a 10uF decoupling capacitor. The diode in serie of the reset signal converts the GPIO push-pull output into a open-drain output. So a post reset delay in the range of 500-1000ms is needed, depending on component tolerances and general hardware design margins. In the first version of this patch series[6] I reused the "reset-delay-us" property for reset deassert in usec as that would cause 50/50% duty-cycle, but that would always apply. The solution in this patch series is to add a new MDIO bus property, so post reset delay is optional and configured separately. MDIO bus properties[7]: "reset-delay-us" "reset-post-delay-us" (new) I have not marked this with "Fixes:" as no single commit is the cause and historically this code has only supported MDIO devices that need reset after auto-detection. The patch series also uses a new flexible sleep helper function that was introduced in 5.8-rc1, so the driver uses the optimal sleep function depending on value loaded from device tree. Future work in this area could add new properties on the MDIO device, so reset points are configurable, e.g. no reset, before/after auto-detection or both. [1] https://lore.kernel.org/linux-devicetree/20200629114927.17379-2-bruno.thomsen@gmail.com/ [2] https://lore.kernel.org/linux-devicetree/20200716172611.5349-2-bruno.thomsen@gmail.com/ [3] https://elixir.bootlin.com/linux/v5.7.8/source/Documentation/devicetree/bindings/net/fsl-fec.txt#L44 [4] https://elixir.bootlin.com/linux/v5.8-rc4/source/Documentation/devicetree/bindings/net/mdio.yaml#L78 [5] https://lore.kernel.org/netdev/CAOMZO5DtYDomD8FDCZDwYCSr2AwNT81Ay4==aDxXyBxtyvPiJA@mail.gmail.com/ [6] https://lore.kernel.org/netdev/20200728090203.17313-1-bruno.thomsen@gmail.com/ [7] https://elixir.bootlin.com/linux/v5.8-rc4/source/Documentation/devicetree/bindings/net/mdio.yaml#L36 [8] http://ww1.microchip.com/downloads/en/DeviceDoc/00002202C.pdf ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mdio device: use flexible sleeping in reset functionBruno Thomsen
MDIO device reset assert and deassert length was created by usleep_range() but that does not ensure optimal handling of all the different values from device tree properties. By switching to the new flexible sleeping helper function, fsleep(), the correct delay function is called depending on delay length, e.g. udelay(), usleep_range() or msleep(). Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mdiobus: add reset-post-delay-us handlingBruno Thomsen
Load new "reset-post-delay-us" value from MDIO properties, and if configured to a greater then zero delay do a flexible sleeping delay after MDIO bus reset deassert. This allows devices to exit reset state before start bus communication. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mdiobus: use flexible sleeping for reset-delay-usBruno Thomsen
MDIO bus reset pulse width is created by using udelay() and that function might not be optimal depending on device tree value. By switching to the new fsleep() helper the correct delay function is called depending on delay length, e.g. udelay(), usleep_range() or msleep(). Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03dt-bindings: net: mdio: add reset-post-delay-us propertyBruno Thomsen
Add "reset-post-delay-us" parameter to MDIO bus properties, so it's possible to add a delay after reset deassert. This is optional in case external hardware slows down release of the reset signal. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03bpf: Allow to specify ifindex for skb in bpf_prog_test_run_skbDmitry Yakunin
Now skb->dev is unconditionally set to the loopback device in current net namespace. But if we want to test bpf program which contains code branch based on ifindex condition (eg filters out localhost packets) it is useful to allow specifying of ifindex from userspace. This patch adds such option through ctx_in (__sk_buff) parameter. Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200803090545.82046-3-zeil@yandex-team.ru
2020-08-03bpf: Setup socket family and addresses in bpf_prog_test_run_skbDmitry Yakunin
Now it's impossible to test all branches of cgroup_skb bpf program which accesses skb->family and skb->{local,remote}_ip{4,6} fields because they are zeroed during socket allocation. This commit fills socket family and addresses from related fields in constructed skb. Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200803090545.82046-2-zeil@yandex-team.ru
2020-08-03net/mlx5: Delete extra dump stack that gives nothingLeon Romanovsky
The WARN_*() macros are intended to catch impossible situations from the SW point of view. They gave a little in case HW<->SW interface is out-of-sync. Such out-of-sync scenario can be due to SW errors that are not part of this flow or because some HW errors, where dump stack won't help either. This specific WARN_ON() is useless because mlx5_core code is prepared to handle such situations and will unfold everything correctly while providing enough information to the users to understand why FS is not working. WARNING: CPU: 0 PID: 3222 at drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 connect_fts_in_prio.isra.20+0x1dd/0x260 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 Kernel panic - not syncing: panic_on_warn set ... CPU: 0 PID: 3222 Comm: syz-executor861 Not tainted 5.5.0-rc6+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Call Trace: __dump_stack linux/lib/dump_stack.c:77 [inline] dump_stack+0x94/0xce linux/lib/dump_stack.c:118 panic+0x234/0x56f linux/kernel/panic.c:221 __warn+0x1cc/0x1e1 linux/kernel/panic.c:582 report_bug+0x200/0x310 linux/lib/bug.c:195 fixup_bug.part.11+0x32/0x80 linux/arch/x86/kernel/traps.c:174 fixup_bug linux/arch/x86/kernel/traps.c:273 [inline] do_error_trap+0xd3/0x100 linux/arch/x86/kernel/traps.c:267 do_invalid_op+0x31/0x40 linux/arch/x86/kernel/traps.c:286 invalid_op+0x1e/0x30 linux/arch/x86/entry/entry_64.S:1027 RIP: 0010:connect_fts_in_prio.isra.20+0x1dd/0x260 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 Code: 00 00 48 c7 c2 60 8c 31 84 48 c7 c6 00 81 31 84 48 8b 38 e8 3c a8 cb ff 41 83 fd 01 8b 04 24 0f 8e 29 ff ff ff e8 83 7b bc fe <0f> 0b 8b 04 24 e9 1a ff ff ff 89 04 24 e8 c1 20 e0 fe 8b 04 24 eb RSP: 0018:ffffc90004bb7858 EFLAGS: 00010293 RAX: ffff88805de98e80 RBX: 0000000000000c96 RCX: ffffffff827a853d RDX: 0000000000000000 RSI: 0000000000000000 RDI: fffff52000976efa RBP: 0000000000000007 R08: ffffed100da060e3 R09: ffffed100da060e3 R10: 0000000000000001 R11: ffffed100da060e2 R12: dffffc0000000000 R13: 0000000000000002 R14: ffff8880683a1a10 R15: ffffed100d07bc1c connect_prev_fts linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:844 [inline] connect_flow_table linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:975 [inline] __mlx5_create_flow_table+0x8f8/0x1710 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1064 mlx5_create_flow_table linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1094 [inline] mlx5_create_auto_grouped_flow_table+0xe1/0x210 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1136 _get_prio linux/drivers/infiniband/hw/mlx5/main.c:3286 [inline] get_flow_table+0x2ea/0x760 linux/drivers/infiniband/hw/mlx5/main.c:3376 mlx5_ib_create_flow+0x331/0x11c0 linux/drivers/infiniband/hw/mlx5/main.c:3896 ib_uverbs_ex_create_flow+0x13e8/0x1b40 linux/drivers/infiniband/core/uverbs_cmd.c:3311 ib_uverbs_write+0xaa5/0xdf0 linux/drivers/infiniband/core/uverbs_main.c:769 __vfs_write+0x7c/0x100 linux/fs/read_write.c:494 vfs_write+0x168/0x4a0 linux/fs/read_write.c:558 ksys_write+0xc8/0x200 linux/fs/read_write.c:611 do_syscall_64+0x9c/0x390 linux/arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45a059 Code: 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fcc17564c98 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007fcc17564ca0 RCX: 000000000045a059 RDX: 0000000000000030 RSI: 00000000200003c0 RDI: 0000000000000005 RBP: 0000000000000007 R08: 0000000000000002 R09: 0000000000003131 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006e636c R13: 0000000000000000 R14: 00000000006e6360 R15: 00007ffdcbdaf6a0 Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Rebooting in 1 seconds.. Fixes: f90edfd279f3 ("net/mlx5_core: Connect flow tables") Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
2020-08-03net/mlx5: convert to new udp_tunnel infrastructureJakub Kicinski
Allocate nic_info dynamically - n_entries is not constant. Attach the tunnel offload info only to the uplink representor. We expect the "main" netdev to be unregistered in switchdev mode, and there to be only one uplink representor. Drop the udp_tunnel_drop_rx_info() call, it was not there until commit b3c2ed21c0bd ("net/mlx5e: Fix VXLAN configuration restore after function reload") so the device doesn't need it, and core should handle reloads and reset just fine. v2: - don't drop the ndos on reprs, and register info on uplink repr. v4: - Move netdev tunnel structure handling to en_main.c Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-08-03udp_tunnel: add the ability to hard-code IANA VXLANJakub Kicinski
mlx5 has the IANA VXLAN port (4789) hard coded by the device, instead of being added dynamically when tunnels are created. To support this add a workaround flag to struct udp_tunnel_nic_info. Skipping updates for the port is fairly trivial, dumping the hard coded port via ethtool requires some code duplication. The port is not a part of any real table, we dump it in a special table which has no tunnel types supported and only one entry. This is the last known workaround / hack needed to convert all drivers to the new infra. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-08-03net/mlx5: DR, Change push vlan action sequenceAlex Vesker
The DR TX state machine supports the following order: modify header, push vlan and encapsulation. Instead fs_dr would pass: push vlan, modify header and encapsulation. The above caused the rule creation to fail on invalid action sequence provided error. Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation") Signed-off-by: Alex Vesker <valex@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-08-03net/mlx5e: Enable users to change VF/PF representors carrier stateParav Pandit
Currently PF and VF representor netdevice carrier is always controlled by controlling the representor netdevice device state as up/down. Representor netdevice state change undergoes one or more txq/rxq destroy/create commands to firmware, skb and its rx buffer allocation, health reporters creation and more. Due to this limitation users do not have the ability to just change the carrier of the non uplink representors without modifying the device state. In one use case when the eswitch physical port carrier is down/up, user needs to update the VF link state to same as physical port carrier. Example of updating VF representor carrier state: $ ip link set enp0s8f0npf0vf0 carrier off $ ip link set enp0s8f0npf0vf0 carrier on This enhancement results into VF link state change which is represented by the VF representor netdevice carrier. This enables users to modify the representor carrier without modifying the representor netdevice state. A simple test is run using [1] to calculate the time difference between updating carrier vs updating device state (to update just the carrier) with one VF to simulate 255 VFs. Time taken to update the carrier using device up/down: $ time ./calculate.sh dev enp0s8f0npf0vf0 real 0m30.913s user 0m0.200s sys 0m11.168s Time taken to update just the carrier using carrier iproute2 command: $ time ./calculate.sh carrier enp0s8f0npf0vf0 real 0m2.142s user 0m0.160s sys 0m2.021s Test shows that its better to use carrier on/off user interface to notify link up/down event to VF compare to device up/down interface, because carrier user interface delivers the same event 15 times faster. [1] https://github.com/paravmellanox/myscripts/blob/master/calculate_carrier_time.sh Signed-off-by: Parav Pandit <parav@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-08-03Merge branch 'bpf-libbpf-btf-parsing'Daniel Borkmann
Andrii Nakryiko says: ==================== It's pretty common for applications to want to parse raw (binary) BTF data from file, as opposed to parsing it from ELF sections. It's also pretty common for tools to not care whether given file is ELF or raw BTF format. This patch series exposes internal raw BTF parsing API and adds generic variant of BTF parsing, which will efficiently determine the format of a given fail and will parse BTF appropriately. Patches #2 and #3 removes re-implementations of such APIs from bpftool and resolve_btfids tools. ==================== Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2020-08-03tools/resolve_btfids: Use libbpf's btf__parse() APIAndrii Nakryiko
Instead of re-implementing generic BTF parsing logic, use libbpf's API. Also add .gitignore for resolve_btfids's build artifacts. Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200802013219.864880-4-andriin@fb.com
2020-08-03tools/bpftool: Use libbpf's btf__parse() API for parsing BTF from fileAndrii Nakryiko
Use generic libbpf API to parse BTF data from file, instead of re-implementing it in bpftool. Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200802013219.864880-3-andriin@fb.com
2020-08-03libbpf: Add btf__parse_raw() and generic btf__parse() APIsAndrii Nakryiko
Add public APIs to parse BTF from raw data file (e.g., /sys/kernel/btf/vmlinux), as well as generic btf__parse(), which will try to determine correct format, currently either raw or ELF. Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200802013219.864880-2-andriin@fb.com
2020-08-03tools, bpftool: Fix wrong return value in do_dump()Tianjia Zhang
In case of btf_id does not exist, a negative error code -ENOENT should be returned. Fixes: c93cc69004df3 ("bpftool: add ability to dump BTF types") Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Andrii Nakryiko <andriin@fb.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200802111540.5384-1-tianjia.zhang@linux.alibaba.com
2020-08-03tools, build: Propagate build failures from tools/build/Makefile.buildAndrii Nakryiko
The '&&' command seems to have a bad effect when $(cmd_$(1)) exits with non-zero effect: the command failure is masked (despite `set -e`) and all but the first command of $(dep-cmd) is executed (successfully, as they are mostly printfs), thus overall returning 0 in the end. This means in practice that despite compilation errors, tools's build Makefile will return success. We see this very reliably with libbpf's Makefile, which doesn't get compilation error propagated properly. This in turns causes issues with selftests build, as well as bpftool and other projects that rely on building libbpf. The fix is simple: don't use &&. Given `set -e`, we don't need to chain commands with &&. The shell will exit on first failure, giving desired behavior and propagating error properly. Fixes: 275e2d95591e ("tools build: Move dependency copy into function") Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jiri Olsa <jolsa@redhat.com> Link: https://lore.kernel.org/bpf/20200731024244.872574-1-andriin@fb.com
2020-08-03mac80211: Do not report beacon loss if beacon filtering enabledLoic Poulain
mac80211.h says: Beacon filter support is advertised with the IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to enable beacon filter support whenever power save is enabled, that is IEEE80211_CONF_PS is set. When power save is enabled, the stack will not check for beacon loss and the driver needs to notify about loss of beacons with ieee80211_beacon_loss(). Some controllers may want to dynamically enable the beacon filter capabilities on power save entry (CONF_PS) and disable it on exit. This is the case for the wcn36xx driver which only supports beacon filtering in PS mode (no CONNECTION_MONITOR support). When the mac80211 beacon monitor timer expires, the beacon filter flag must be checked again in case it as been changed in between (e.g. vif moved to PS mode). Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-03netfilter: flowtable: Set offload timeout when adding flowRoi Dayan
On heavily loaded systems the GC can take time to go over all existing conns and reset their timeout. At that time other calls like from nf_conntrack_in() can call of nf_ct_is_expired() and see the conn as expired. To fix this when we set the offload bit we should also reset the timeout instead of counting on GC to finish first iteration over all conns before the initial timeout. Fixes: 90964016e5d3 ("netfilter: nf_conntrack: add IPS_OFFLOAD status bit") Signed-off-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-03netfilter: conntrack: Move nf_ct_offload_timeout to header fileRoi Dayan
To be used by callers from other modules. [ Rename DAY to NF_CT_DAY to avoid possible symbol name pollution issue --Pablo ] Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-03selftests: netfilter: add meta iif/oif match testFlorian Westphal
simple test case, but would have caught this: FAIL: iifgroupcount, want "packets 2", got table inet filter { counter iifgroupcount { packets 0 bytes 0 } } Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-03mac80211: fix misplaced while instead of ifJohannes Berg
This never was intended to be a 'while' loop, it should've just been an 'if' instead of 'while'. Fix this. I noticed this while applying another patch from Ben that intended to fix a busy loop at this spot. Cc: stable@vger.kernel.org Fixes: b16798f5b907 ("mac80211: mark station unauthorized before key removal") Reported-by: Ben Greear <greearb@candelatech.com> Link: https://lore.kernel.org/r/20200803110209.253009ae41ff.I3522aad099392b31d5cf2dcca34cbac7e5832dde@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-03nl80211: use eth_zero_addr() to clear mac addressMiaohe Lin
Use eth_zero_addr() to clear mac address instead of memset(). Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Link: https://lore.kernel.org/r/1596273349-24333-1-git-send-email-linmiaohe@huawei.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-03mac80211: use eth_zero_addr() to clear mac addressMiaohe Lin
Use eth_zero_addr() to clear mac address instead of memset(). Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Link: https://lore.kernel.org/r/1596273158-24183-1-git-send-email-linmiaohe@huawei.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-03mac8211: fix struct initialisationJohn Crispin
Sparse showed up with the following error. net/mac80211/agg-rx.c:480:43: warning: Using plain integer as NULL pointer Fixes: 2ab45876756f (mac80211: add support for the ADDBA extension element) Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/20200803084540.179908-1-john@phrozen.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-03mac80211: Handle special status codes in SAE commitJouni Malinen
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK (WFA) options. Those extensions use special status code values in the SAE commit messages (Authentication frame with transaction sequence number 1) to identify which extension is in use. mac80211 was interpreting those new values as the AP denying authentication and that resulted in failure to complete SAE authentication in some cases. Fix this by adding exceptions for the new status code values 126 and 127. Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-08-02netfilter: nf_tables: report EEXIST on overlapsPablo Neira Ayuso
Replace EBUSY by EEXIST in the following cases: - If the user adds a chain with a different configuration such as different type, hook and priority. - If the user adds a non-base chain that clashes with an existing basechain. - If the user adds a { key : value } mapping element and the key exists but the value differs. - If the device already belongs to an existing flowtable. User describe that this error reporting is confusing: - https://bugzilla.netfilter.org/show_bug.cgi?id=1176 - https://bugzilla.netfilter.org/show_bug.cgi?id=1413 Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-08-02brcmfmac: Set timeout value when configuring power saveNicolas Saenz Julienne
Set the timeout value as per cfg80211's set_power_mgmt() request. If the requested value value is left undefined we set it to 2 seconds, the maximum supported value. Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200721112302.22718-1-nsaenzjulienne@suse.de
2020-08-02bcma: gpio: Use irqchip templateLinus Walleij
This makes the driver use the irqchip template to assign properties to the gpio_irq_chip instead of using the explicit call to gpiochip_irqchip_add(). The irqchip is instead added while adding the gpiochip. Cc: Rafał Miłecki <rafal@milecki.pl> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200722111725.210923-1-linus.walleij@linaro.org
2020-08-02drivers: bcma: remove set but not used variable `addrh` and `sizeh`Zheng Yongjun
Fixes gcc '-Wunused-but-set-variable' warning: drivers/bcma/scan.c: In function 'bcma_erom_get_addr_desc': drivers/bcma/scan.c:219 warning: variable `addrh` and `sizeh` set but not used [-Wunused-but-set-variable] Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200721083935.13306-1-zhengyongjun3@huawei.com
2020-08-02wl1251: fix always return 0 errorWang Hai
wl1251_event_ps_report() should not always return 0 because wl1251_ps_set_mode() may fail. Change it to return 'ret'. Fixes: f7ad1eed4d4b ("wl1251: retry power save entry") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200730073939.33704-1-wanghai38@huawei.com
2020-08-02airo: use generic power managementVaibhav Gupta
Drivers using legacy power management .suspen()/.resume() callbacks have to manage PCI states and device's PM states themselves. They also need to take care of standard configuration registers. Switch to generic power management framework using a single "struct dev_pm_ops" variable to take the unnecessary load from the driver. This also avoids the need for the driver to directly call most of the PCI helper functions and device power state control functions, as through the generic framework PCI Core takes care of the necessary operations, and drivers are required to do only device-specific jobs. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200728114128.1218310-1-vaibhavgupta40@gmail.com
2020-08-02intersil: fix wiki website urlFlavio Suligoi
In some Intersil files, the wiki url is still the old "wireless.kernel.org" instead of the new "wireless.wiki.kernel.org" Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200723135254.594984-1-f.suligoi@asem.it
2020-08-02qtnfmac: Missing platform_device_unregister() on error in qtnf_core_mac_alloc()Wang Hai
Add the missing platform_device_unregister() before return from qtnf_core_mac_alloc() in the error handling case. Fixes: 616f5701f4ab ("qtnfmac: assign each wiphy to its own virtual platform device") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200730064910.37589-1-wanghai38@huawei.com
2020-08-02ipw2x00: switch from 'pci_' to 'dma_' APIChristophe JAILLET
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'ipw2100_msg_allocate()' (ipw2100.c), GFP_KERNEL can be used because it is called from the probe function. The call chain is: ipw2100_pci_init_one (the probe function) --> ipw2100_queues_allocate --> ipw2100_msg_allocate Moreover, 'ipw2100_msg_allocate()' already uses GFP_KERNEL for some other memory allocations. When memory is allocated in 'status_queue_allocate()' (ipw2100.c), GFP_KERNEL can be used because it is called from the probe function. The call chain is: ipw2100_pci_init_one (the probe function) --> ipw2100_queues_allocate --> ipw2100_rx_allocate --> status_queue_allocate Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other memory allocations. When memory is allocated in 'bd_queue_allocate()' (ipw2100.c), GFP_KERNEL can be used because it is called from the probe function. The call chain is: ipw2100_pci_init_one (the probe function) --> ipw2100_queues_allocate --> ipw2100_rx_allocate --> bd_queue_allocate Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other memory allocations. When memory is allocated in 'ipw2100_tx_allocate()' (ipw2100.c), GFP_KERNEL can be used because it is called from the probe function. The call chain is: ipw2100_pci_init_one (the probe function) --> ipw2100_queues_allocate --> ipw2100_tx_allocate Moreover, 'ipw2100_tx_allocate()' already uses GFP_KERNEL for some other memory allocations. When memory is allocated in 'ipw_queue_tx_init()' (ipw2200.c), GFP_KERNEL can be used because it is called from a call chain that already uses GFP_KERNEL and no spin_lock is taken in the between. The call chain is: ipw_up --> ipw_load --> ipw_queue_reset --> ipw_queue_tx_init 'ipw_up()' already uses GFP_KERNEL for some other memory allocations. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200722101716.26185-1-christophe.jaillet@wanadoo.fr
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-01 22:51:46 +0000