summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-07-28Merge branch 'mlxsw-Add-support-for-QSFP-DD-transceiver-type'David S. Miller
Ido Schimmel says: ==================== mlxsw: Add support for QSFP-DD transceiver type This patch set from Vadim adds support for Quad Small Form Factor Pluggable Double Density (QSFP-DD) modules in mlxsw. Patch #1 enables dumping of QSFP-DD module information through ethtool. Patch #2 enables reading of temperature thresholds from QSFP-DD modules for hwmon and thermal zone purposes. Changes since v1 [1]: Only rebase on top of net-next. After discussing with Andrew and Adrian we agreed that current approach is OK and that in the future we can follow Andrew's suggestion to "make a new API where user space can request any pages it want, and specify the size of the page". This should allow us "to work around known issues when manufactures get their EEPROM wrong". [1] https://lore.kernel.org/netdev/20200626144724.224372-1-idosch@idosch.org/#t ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28mlxsw: core: Add support for temperature thresholds reading for QSFP-DD ↵Vadim Pasternak
transceivers Allow QSFP-DD transceivers temperature thresholds reading for hardware monitoring and thermal control. For this type, the thresholds are located in page 02h according to the "Module and Lane Thresholds" description from Common Management Interface Specification. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28mlxsw: core: Add ethtool support for QSFP-DD transceiversVadim Pasternak
The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware specification defines a form factor that supports up to 400 Gbps in aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports both optical and copper interfaces. Implementation is based on Common Management Interface Specification; Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower Page)" from this spec defines "Id and Status" fields located at offsets 00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory mode, which could be "upper memory flat" or "paged". Flat memory mode is coded "1", and indicates that only page 00h is implemented in EEPROM. Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h and 11h are implemented. Pages 10h and 11h are currently not supported by the driver. "Flat" memory mode is used for the passive copper transceivers. For this type only page 00h (256 bytes) is available. "Paged" memory is used for the optical transceivers. For this type pages 00h (256 bytes), 01h (128 bytes) and 02h (128 bytes) are available. Upper page 01h contains static advertising field, while upper page 02h contains the module-defined thresholds and lane-specific monitors. Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to indicate for QSFP-DD transceiver type which memory mode is to be used. Expose 256 bytes buffer for QSFP-DD passive copper transceiver and 512 bytes buffer for optical. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28Merge tag 'mlx5-updates-2020-07-28' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2020-07-28 Misc and small update to mlx5 driver: 1) Aya adds PCIe relaxed ordering support for mlx5 netdev queues. 2) Eran Refactors pages data base to be per vf/function to speedup unload time. 3) Parav changes eswitch steering initialization to account for tota_vports rather than for only active vports and Link non uplink representors to PCI device, for uniform naming scheme. 4) Tariq, trivial RX code improvements and missing inidirect calls wrappers. 5) Small cleanup patches ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28usb: hso: check for return value in hso_serial_common_create()Rustam Kovhaev
in case of an error tty_register_device_attr() returns ERR_PTR(), add IS_ERR() check Reported-and-tested-by: syzbot+67b2bd0e34f952d0321e@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=67b2bd0e34f952d0321e Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28farsync: use generic power managementVaibhav Gupta
The .suspend() and .resume() callbacks are not defined for this driver. Still, their power management structure follows the legacy framework. To bring it under the generic framework, simply remove the binding of callbacks from "struct pci_driver". Change code indentation from space to tab in "struct pci_driver". Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net/mlx5e: Fix kernel crash when setting vf VLANID on a VF devAlaa Hleihel
After the cited commit, function 'mlx5_eswitch_set_vport_vlan' started to acquire esw->state_lock. However, esw is not defined for VF devices, hence attempting to set vf VLANID on a VF dev will cause a kernel panic. Fix it by moving up the (redundant) esw validation from function '__mlx5_eswitch_set_vport_vlan' since the rest of the callers now have and use a valid esw. For example with vf device eth4: # ip link set dev eth4 vf 0 vlan 0 Trace of the panic: [ 411.409842] BUG: unable to handle page fault for address: 00000000000011b8 [ 411.449745] #PF: supervisor read access in kernel mode [ 411.452348] #PF: error_code(0x0000) - not-present page [ 411.454938] PGD 80000004189c9067 P4D 80000004189c9067 PUD 41899a067 PMD 0 [ 411.458382] Oops: 0000 [#1] SMP PTI [ 411.460268] CPU: 4 PID: 5711 Comm: ip Not tainted 5.8.0-rc4_for_upstream_min_debug_2020_07_08_22_04 #1 [ 411.462447] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 411.464158] RIP: 0010:__mutex_lock+0x4e/0x940 [ 411.464928] Code: fd 41 54 49 89 f4 41 52 53 89 d3 48 83 ec 70 44 8b 1d ee 03 b0 01 65 48 8b 04 25 28 00 00 00 48 89 45 c8 31 c0 45 85 db 75 0a <48> 3b 7f 60 0f 85 7e 05 00 00 49 8d 45 68 41 56 41 b8 01 00 00 00 [ 411.467678] RSP: 0018:ffff88841fcd74b0 EFLAGS: 00010246 [ 411.468562] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 [ 411.469715] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000001158 [ 411.470812] RBP: ffff88841fcd7550 R08: ffffffffa00fa1ce R09: 0000000000000000 [ 411.471835] R10: ffff88841fcd7570 R11: 0000000000000000 R12: 0000000000000002 [ 411.472862] R13: 0000000000001158 R14: ffffffffa00fa1ce R15: 0000000000000000 [ 411.474004] FS: 00007faee7ca6b80(0000) GS:ffff88846fc00000(0000) knlGS:0000000000000000 [ 411.475237] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 411.476129] CR2: 00000000000011b8 CR3: 000000041909c006 CR4: 0000000000360ea0 [ 411.477260] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 411.478340] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 411.479332] Call Trace: [ 411.479760] ? __nla_validate_parse.part.6+0x57/0x8f0 [ 411.482825] ? mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core] [ 411.483804] mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core] [ 411.484733] mlx5e_set_vf_vlan+0x41/0x50 [mlx5_core] [ 411.485545] do_setlink+0x613/0x1000 [ 411.486165] __rtnl_newlink+0x53d/0x8c0 [ 411.486791] ? mark_held_locks+0x49/0x70 [ 411.487429] ? __lock_acquire+0x8fe/0x1eb0 [ 411.488085] ? rcu_read_lock_sched_held+0x52/0x60 [ 411.488998] ? kmem_cache_alloc_trace+0x16d/0x2d0 [ 411.489759] rtnl_newlink+0x47/0x70 [ 411.490357] rtnetlink_rcv_msg+0x24e/0x450 [ 411.490978] ? netlink_deliver_tap+0x92/0x3d0 [ 411.491631] ? validate_linkmsg+0x330/0x330 [ 411.492262] netlink_rcv_skb+0x47/0x110 [ 411.492852] netlink_unicast+0x1ac/0x270 [ 411.493551] netlink_sendmsg+0x336/0x450 [ 411.494209] sock_sendmsg+0x30/0x40 [ 411.494779] ____sys_sendmsg+0x1dd/0x1f0 [ 411.495378] ? copy_msghdr_from_user+0x5c/0x90 [ 411.496082] ___sys_sendmsg+0x87/0xd0 [ 411.496683] ? lock_acquire+0xb9/0x3a0 [ 411.497322] ? lru_cache_add+0x5/0x170 [ 411.497944] ? find_held_lock+0x2d/0x90 [ 411.498568] ? handle_mm_fault+0xe46/0x18c0 [ 411.499205] ? __sys_sendmsg+0x51/0x90 [ 411.499784] __sys_sendmsg+0x51/0x90 [ 411.500341] do_syscall_64+0x59/0x2e0 [ 411.500938] ? asm_exc_page_fault+0x8/0x30 [ 411.501609] ? rcu_read_lock_sched_held+0x52/0x60 [ 411.502350] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 411.503093] RIP: 0033:0x7faee73b85a7 [ 411.503654] Code: Bad RIP value. Fixes: 0e18134f4f9f ("net/mlx5e: Eswitch, use state_lock to synchronize vlan change") Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Modify uplink state on interface up/downRon Diskin
When setting the PF interface up/down, notify the firmware to update uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled. This behavior will prevent sending traffic out on uplink port when PF is down, such as sending traffic from a VF interface which is still up. Currently when calling mlx5e_open/close(), the driver only sends PAOS command to notify the firmware to set the physical port state to up/down, however, it is not sufficient. When VF is in "auto" state, it follows the uplink state, which was not updated on mlx5e_open/close() before this patch. When switchdev mode is enabled and uplink representor is first enabled, set the uplink port state value back to its FW default "AUTO". Fixes: 63bfd399de55 ("net/mlx5e: Send PAOS command on interface up/down") Signed-off-by: Ron Diskin <rondi@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Query PPS pin operational status before registering itEran Ben Elisha
In a special configuration, a ConnectX6-Dx pin pps-out might be activated when driver is loaded. Fix the driver to always read the operational pin mode when registering it, and advertise it accordingly. Fixes: ee7f12205abc ("net/mlx5e: Implement 1PPS support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Fix slab-out-of-bounds in mlx5e_rep_is_lag_netdevRaed Salem
mlx5e_rep_is_lag_netdev is used as first check as part of netdev events handler for bond device of non-uplink representors, this handler can get any netdevice under the same network namespace of mlx5e netdevice. Current code treats the netdev as mlx5e netdev and only later on verifies this, hence causes the following Kasan trace: [15402.744990] ================================================================== [15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347 [15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G B O --------- -t - 4.18.0-g3dcc204d291d-dirty #1 [15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [15402.757600] Call Trace: [15402.758968] dump_stack+0x71/0xab [15402.760427] print_address_description+0x6a/0x270 [15402.761969] kasan_report+0x179/0x2d0 [15402.763445] ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.765121] mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core] [15402.766782] mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core] Fix by deferring the violating access to be post the netdev verify check. Fixes: 7e51891a237f ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule") Signed-off-by: Raed Salem <raeds@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Vu Pham <vuhuong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Verify Hardware supports requested ptp function on a given pinEran Ben Elisha
Fix a bug where driver did not verify Hardware pin capabilities for PTP functions. Fixes: ee7f12205abc ("net/mlx5e: Implement 1PPS support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Ariel Levkovich <lariel@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Fix a bug of using ptp channel index as pin indexEran Ben Elisha
On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index as pin index. After ptp patch marked in fixes tag was introduced, driver can freely call ptp_find_pin() as part of the .enable() callback. Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow. In addition, when initializing the pins, always set channel to zero. As all pins can be attached to all channels, let ptp_set_pinfunc() to move them between the channels. For stable branches, this fix to be applied only on kernels that includes both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck on pincfg_mux. Fixes: 62582a7ee783 ("ptp: Avoid deadlocks in the programmable pin code.") Fixes: ee7f12205abc ("net/mlx5e: Implement 1PPS support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Ariel Levkovich <lariel@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Fix missing cleanup of ethtool steering during rep rx cleanupMaor Dickman
The cited commit add initialization of ethtool steering during representor rx initializations without cleaning it up in representor rx cleanup, this may cause for stale ethtool flows to remain after moving back from switchdev mode to legacy mode. Fixed by calling ethtool steering cleanup during rep rx cleanup. Fixes: 6783e8b29f63 ("net/mlx5e: Init ethtool steering for representors") Signed-off-by: Maor Dickman <maord@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Fix error path of device attachAya Levin
On failure to attach the netdev, fix the rollback by re-setting the device's state back to MLX5E_STATE_DESTROYING. Failing to attach doesn't stop statistics polling via .ndo_get_stats64. In this case, although the device is not attached, it falsely continues to query the firmware for counters. Setting the device's state back to MLX5E_STATE_DESTROYING prevents the firmware counters query. Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Fix forward to next namespaceMaor Gottlieb
The steering tree is as follow (nic RX as example): --------- |root_ns| --------- | -------------------------------- | | | ---------- ---------- --------- |p(prio)0| | p1 | | pn | ---------- ---------- --------- | | ---------------- --------------- |ns(e.g bypass)| |ns(e.g. lag) | ---------------- --------------- | | | ---- ---- ---- |p0| |p1| |pn| ---- ---- ---- | ---- |FT| ---- find_next_chained_ft(prio) returns the first flow table in the next priority. If prio is a parent of a flow table then it returns the first flow table in the next priority in the same namespace, else if prio is parent of namespace, then it should return the first flow table in the next namespace. Currently if the user requests to forward to next namespace, the code calls to find_next_chained_ft with the prio of the next namespace and not the prio of the namesapce itself. Fixes: 9254f8ed15b6 ("net/mlx5: Add support in forward to namespace") Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: E-switch, Destroy TSAR after reload interfaceParav Pandit
When eswitch offloads is enabled, TSAR is created before reloading the interfaces. However when eswitch offloads mode is disabled, TSAR is disabled before reloading the interfaces. To keep the eswitch enable/disable sequence as mirror, destroy TSAR after reloading the interfaces. Fixes: 1bd27b11c1df ("net/mlx5: Introduce E-switch QoS management") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: E-switch, Destroy TSAR when fail to enable the modeParav Pandit
When either esw_legacy_enable() or esw_offloads_enable() fails, code missed to destroy the created TSAR. Hence, add the missing call to destroy the TSAR. Fixes: 610090ebce92 ("net/mlx5: E-switch, Initialize TSAR Qos hardware block before its user vports") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28Merge branch 'hns3-fixes'David S. Miller
Huazhong Tan says: ==================== net: hns3: fixes for -net There are some bugfixes for the HNS3 ethernet driver. patch#1 fixes a desc filling bug, patch#2 fixes a false TX timeout issue, and patch#3~#5 fixes some bugs related to VLAN and FD. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net: hns3: fix for VLAN config when reset failedGuojia Liao
When device is resetting or reset failed, firmware is unable to handle mailbox. VLAN should not be configured in this case. Fixes: fe4144d47eef ("net: hns3: sync VLAN filter entries when kill VLAN ID failed") Signed-off-by: Guojia Liao <liaoguojia@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net: hns3: fix aRFS FD rules leftover after add a user FD ruleGuojia Liao
When user had created a FD rule, all the aRFS rules should be clear up. HNS3 process flow as below: 1.get spin lock of fd_ruls_list 2.clear up all aRFS rules 3.release lock 4.get spin lock of fd_ruls_list 5.creat a rules 6.release lock; There is a short period of time between step 3 and step 4, which would creatting some new aRFS FD rules if driver was receiving packet. So refactor the fd_rule_lock to fix it. Fixes: 441228875706 ("net: hns3: refine the flow director handle") Signed-off-by: Guojia Liao <liaoguojia@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net: hns3: add reset check for VF updating port based VLANJian Shen
Currently hclgevf_update_port_base_vlan_info() may be called when VF is resetting, which may cause hns3_nic_net_open() being called twice unexpectedly. So fix it by adding a reset check for it, and extend critical region for rntl_lock in hclgevf_update_port_base_vlan_info(). Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net: hns3: fix a TX timeout issueYonglong Liu
When the queue depth and queue parameters are modified, there is a low probability that TX timeout occurs. The two operations cause the link to be down or up when the watchdog is still working. All queues are stopped when the link is down. After the carrier is on, all queues are woken up. If the watchdog detects the link between the carrier on and wakeup queues, a false TX timeout occurs. So fix this issue by modifying the sequence of carrier on and queue wakeup, which is symmetrical to the link down action. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28net: hns3: fix desc filling bug when skb is expanded or linearedYunsheng Lin
The linear and frag data part may be changed when the skb is expanded or lineared in skb_cow_head() or skb_checksum_help(), which is called by hns3_fill_skb_desc(), so the linear len return by skb_headlen() before the calling of hns3_fill_skb_desc() is unreliable. Move hns3_fill_skb_desc() before the calling of skb_headlen() to fix this bug. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-28Merge tag 'asm-generic-fixes-5.8' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic into master Pull asm-generic bugfix from Arnd Bergmann: "A single bugfix for a regression introduced through a typo in the v5.8 merge window, leading to incorrect data returned from inl() on some architectures" * tag 'asm-generic-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: io: Fix return type of _inb and _inl
2020-07-28Merge tag 'arm-fixes-5.8-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master Pull ARM SoC DT fixes from Arnd Bergmann: "These are the latest device tree fixes for Arm SoCs: - TI Keystone2 ethernet regressed after a driver change broke with incorrect phy-mode in a board's DT source. - A similar fix is needed for two i.MX boards that were missed in an earlier bugfix. - DT change for Armada 38x allowing to add the register needed to fix NETA lockup when repeatedly switching speed. - One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card detect work correctly. - Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that were failing on older SoCs and one to fix Cedrus on the H6" * tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: dts: keystone-k2g-evm: fix rgmii phy-mode for ksz9031 phy ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2 ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2 arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage ARM: dts sunxi: Relax a bit the CMA pool allocation range
2020-07-28Bluetooth: hci_qca: Stop collecting memdump again for command timeout during SSRVenkata Lakshmi Narayana Gubba
Setting memdump state to idle prior to setting of callback function pointer for command timeout to NULL,causing the issue.Now moved the initialisation of memdump state to qca_setup(). Fixes: d841502c79e3 ("Bluetooth: hci_qca: Collect controller memory dump during SSR") Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28Bluetooth: Fix suspend notifier raceAbhishek Pandit-Subedi
Unregister from suspend notifications and cancel suspend preparations before running hci_dev_do_close. Otherwise, the suspend notifier may race with unregister and cause cmd_timeout even after hdev has been freed. Below is the trace from when this panic was seen: [ 832.578518] Bluetooth: hci_core.c:hci_cmd_timeout() hci0: command 0x0c05 tx timeout [ 832.586200] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 832.586203] #PF: supervisor read access in kernel mode [ 832.586205] #PF: error_code(0x0000) - not-present page [ 832.586206] PGD 0 P4D 0 [ 832.586210] PM: suspend exit [ 832.608870] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 832.613232] CPU: 3 PID: 10755 Comm: kworker/3:7 Not tainted 5.4.44-04894-g1e9dbb96a161 #1 [ 832.630036] Workqueue: events hci_cmd_timeout [bluetooth] [ 832.630046] RIP: 0010:__queue_work+0xf0/0x374 [ 832.630051] RSP: 0018:ffff9b5285f1fdf8 EFLAGS: 00010046 [ 832.674033] RAX: ffff8a97681bac00 RBX: 0000000000000000 RCX: ffff8a976a000600 [ 832.681162] RDX: 0000000000000000 RSI: 0000000000000009 RDI: ffff8a976a000748 [ 832.688289] RBP: ffff9b5285f1fe38 R08: 0000000000000000 R09: ffff8a97681bac00 [ 832.695418] R10: 0000000000000002 R11: ffff8a976a0006d8 R12: ffff8a9745107600 [ 832.698045] usb 1-6: new full-speed USB device number 119 using xhci_hcd [ 832.702547] R13: ffff8a9673658850 R14: 0000000000000040 R15: 000000000000001e [ 832.702549] FS: 0000000000000000(0000) GS:ffff8a976af80000(0000) knlGS:0000000000000000 [ 832.702550] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 832.702550] CR2: 0000000000000000 CR3: 000000010415a000 CR4: 00000000003406e0 [ 832.702551] Call Trace: [ 832.702558] queue_work_on+0x3f/0x68 [ 832.702562] process_one_work+0x1db/0x396 [ 832.747397] worker_thread+0x216/0x375 [ 832.751147] kthread+0x138/0x140 [ 832.754377] ? pr_cont_work+0x58/0x58 [ 832.758037] ? kthread_blkcg+0x2e/0x2e [ 832.761787] ret_from_fork+0x22/0x40 [ 832.846191] ---[ end trace fa93f466da517212 ]--- Fixes: 9952d90ea2885 ("Bluetooth: Handle PM_SUSPEND_PREPARE and PM_POST_SUSPEND") Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Reviewed-by: Miao-chen Chou <mcchou@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28i2c: slave: add sanity check when unregisteringWolfram Sang
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: slave: improve sanity check when registeringWolfram Sang
Add check for ERR_PTR and simplify code while here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28net/mlx5: drop unnecessary list_emptyJulia Lawall
list_for_each_entry is able to handle an empty list. The only effect of avoiding the loop is not initializing the index variable. Drop list_empty tests in cases where these variables are not used. Note that list_for_each_entry is defined in terms of list_first_entry, which indicates that it should not be used on an empty list. But in list_for_each_entry, the element obtained by list_first_entry is not really accessed, only the address of its list_head field is compared to the address of the list head, so the list_first_entry is safe. The semantic patch that makes this change is as follows (with another variant for the no brace case): (http://coccinelle.lip6.fr/) <smpl> @@ expression x,e; iterator name list_for_each_entry; statement S; identifier i; @@ -if (!(list_empty(x))) { list_for_each_entry(i,x,...) S - } ... when != i ? i = e </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: DR, Reduce print level for matcher printAlex Vesker
There is no need to print on each unsuccessful matcher ip_version combination since it probably will happen when trying to create all the possible combinations. On a real failure we have a print in the calling function. Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Add support for PCI relaxed orderingAya Levin
The concept of Relaxed Ordering in the PCI Express environment allows switches in the path between the Requester and Completer to reorder some transactions just received before others that were previously enqueued. In ETH driver, there is no question of write integrity since each memory segment is written only once per cycle. In addition, the driver doesn't access the memory shared with the hardware until the corresponding CQE arrives indicating all PCI transactions are done. Running TCP single stream over ConnectX-4 LX, ARM CPU on remote-numa has 300% improvement in the bandwidth. With relaxed ordering turned off: BW:10 [GB/s] With relaxed ordering turned on: BW:40 [GB/s] The driver turns relaxed ordering with respect to the firmware capabilities and the return value from pcie_relaxed_ordering_enabled(). Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Use indirect call wrappers for RX post WQEs functionsTariq Toukan
Use the indirect call wrapper API macros for declaration and scope of the RX post WQEs functions. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Move exposure of datapath function to txrx headerTariq Toukan
Move them from the generic header file "en.h", to the datapath header file "txrx.h". Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: RX, Re-work initializaiton of RX function pointersTariq Toukan
Instead of exposing the RQ datapath handlers (from en_rx.c) so that they are set in the control path (in en_main.c), wrap this logic in a single function in en_rx.c and expose it alone. Every profile will now have a pointer to the new mlx5e_rx_handlers structure, instead of directly pointing to the previously-exposed RQ handlers. This significantly improves locality and modularity of the driver, and allows many functions in en_rx.c to become static. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5e: Link non uplink representors to PCI deviceParav Pandit
Currently PF and VF representors are exposed as virtual device. They are not linked to its parent PCI device like how uplink representor is linked. Due to this, PF and VF representors cannot benefit of the systemd defined naming scheme. This requires special handling by the users. Hence, link the PF and VF representors to their parent PCI device similar to existing uplink representor netdevice. Example: udevadm output before linking to PCI device: $ udevadm test-builtin net_id /sys/class/net/eth6 Load module index Network interface NamePolicy= disabled on kernel command line, ignoring. Parsed configuration file /usr/lib/systemd/network/99-default.link Created link configuration context. Using default interface naming scheme 'v243'. ID_NET_NAMING_SCHEME=v243 Unload module index Unloaded link configuration context. udevadm output after linking to PCI device: $ udevadm test-builtin net_id /sys/class/net/eth6 Load module index Network interface NamePolicy= disabled on kernel command line, ignoring. Parsed configuration file /usr/lib/systemd/network/99-default.link Created link configuration context. Using default interface naming scheme 'v243'. ID_NET_NAMING_SCHEME=v243 ID_NET_NAME_PATH=enp0s8f0npf0vf0 Unload module index Unloaded link configuration context. In past there was little concern over seeing 10,000 lines output showing up at thread [1] is not applicable as ndo ops for VF handling is not exposed for all the 100 repesentors for mlx5 devices. Additionally alternative device naming [2] to overcome shorter device naming is also part of the latest systemd release v245. [1] https://marc.info/?l=linux-netdev&m=152657949117904&w=2 [2] https://lwn.net/Articles/814068/ Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: E-switch, Use eswitch total_vportsParav Pandit
Currently steering table and rx group initialization helper routines works on the total_vports passed as input parameter. Both eswitch helpers work on the mlx5_eswitch and thereby have access to esw->total_vports. Hence use it directly instead of passing it via function input arguments. Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: E-switch, Reuse total_vports and avoid duplicate nvportsParav Pandit
Total e-switch vports are already stored in mlx5_eswitch total_vports. Avoid copy of it in nvports and reuse existing total_vports calculation. Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: E-switch, Consider maximum vf vports for steering initParav Pandit
When eswitch is enabled, VFs might not be enabled. Hence, consider maximum number of VFs. This further closes the gap between handling VF vports between ECPF and PF. Fixes: ea2128fd632c ("net/mlx5: E-switch, Reduce dependency on num_vfs during mode set") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Add function ID to reclaim pages debug logAvihu Hagag
Add function ID to reclaim pages debug log for better user visibility. Signed-off-by: Avihu Hagag <avihuh@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28net/mlx5: Hold pages RB tree per VFEran Ben Elisha
Per page request event, FW request to allocated or release pages for a single function. Driver maintains FW pages object per function, so there is no need to hold one global page data-base. Instead, have a page data-base per function, which will improve performance release flow in all cases, especially for "release all pages". As the range of function IDs is large and not sequential, use xarray to store a per function ID page data-base, where the function ID is the key. Upon first allocation of a page to a function ID, create the page data-base per function. This data-base will be released only at pagealloc mechanism cleanup. NIC: ConnectX-4 Lx CPU: Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz Test case: 32 VFs, measure release pages on one VF as part of FLR Before: 0.021 Sec After: 0.014 Sec The improvement depends on amount of VFs and memory utilization by them. Time measurements above were taken from idle system. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-28ALSA: hda/hdmi: Fix keep_power assignment for non-component devicesTakashi Iwai
It's been reported that, when neither nouveau nor Nvidia graphics driver is used, the screen starts flickering. And, after comparing between the working case (stable 4.4.x) and the broken case, it turned out that the problem comes from the audio component binding. The Nvidia and AMD audio binding code clears the bus->keep_power flag whenever snd_hdac_acomp_init() succeeds. But this doesn't mean that the component is actually bound, but it merely indicates that it's ready for binding. So, when both nouveau and Nvidia are blacklisted or not ready, the driver keeps running without the audio component but also with bus->keep_power = false. This made the driver runtime PM kicked in and powering down when unused, which results in flickering in the graphics side, as it seems. For fixing the bug, this patch moves the bus->keep_power flag change into generic_acomp_notifier_set() that is the function called from the master_bind callback of component ops; i.e. it's guaranteed that the binding succeeded. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208609 Fixes: 5a858e79c911 ("ALSA: hda - Disable audio component for legacy Nvidia HDMI codecs") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200728082033.23933-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2020-07-28Bluetooth: hci_serdev: Only unregister device if it was registeredNicolas Boichat
We should not call hci_unregister_dev if the device was not successfully registered. Fixes: c34dc3bfa7642fd ("Bluetooth: hci_serdev: Introduce hci_uart_unregister_device()") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28Bluetooth: Return NOTIFY_DONE for hci_suspend_notifierMax Chou
The original return is NOTIFY_STOP, but notifier_call_chain would stop the future call for register_pm_notifier even registered on other Kernel modules with the same priority which value is zero. Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28Bluetooth: hci_h5: Set HCI_UART_RESET_ON_INIT to correct flagsNicolas Boichat
HCI_UART_RESET_ON_INIT belongs in hdev_flags, not flags. Fixes: ce945552fde4a09 ("Bluetooth: hci_h5: Add support for serdev enumerated devices") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllersIsmael Ferreras Morezuelas
For some reason they tend to squat on the very first CSR/ Cambridge Silicon Radio VID/PID instead of paying fees. This is an extremely common problem; the issue goes as back as 2013 and these devices are only getting more popular, even rebranded by reputable vendors and sold by retailers everywhere. So, at this point in time there are hundreds of modern dongles reusing the ID of what originally was an early Bluetooth 1.1 controller. Linux is the only place where they don't work due to spotty checks in our detection code. It only covered a minimum subset. So what's the big idea? Take advantage of the fact that all CSR chips report the same internal version as both the LMP sub-version and HCI revision number. It always matches, couple that with the manufacturer code, that rarely lies, and we now have a good idea of who is who. Additionally, by compiling a list of user-reported HCI/lsusb dumps, and searching around for legit CSR dongles in similar product ranges we can find what CSR BlueCore firmware supported which Bluetooth versions. That way we can narrow down ranges of fakes for each of them. e.g. Real CSR dongles with LMP subversion 0x73 are old enough that support BT 1.1 only; so it's a dead giveaway when some third-party BT 4.0 dongle reuses it. So, to sum things up; there are multiple classes of fake controllers reusing the same 0A12:0001 VID/PID. This has been broken for a while. Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891 IC markings on 0x7558: FR3191AHAL 749H15143 (???) https://bugzilla.kernel.org/show_bug.cgi?id=60824 Fixes: 81cac64ba258ae (Deal with USB devices that are faking CSR vendor) Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com> Tested-by: Mike Johnson <yuyuyak@gmail.com> Tested-by: Ricardo Rodrigues <ekatonb@gmail.com> Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com> Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com> Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2020-07-28xfrm: esp6: fix the location of the transport header with encapsulationSabrina Dubroca
commit 17175d1a27c6 ("xfrm: esp6: fix encapsulation header offset computation") changed esp6_input_done2 to correctly find the size of the IPv6 header that precedes the TCP/UDP encapsulation header, but didn't adjust the final call to skb_set_transport_header, which I assumed was correct in using skb_network_header_len. Xiumei Mu reported that when we create xfrm states that include port numbers in the selector, traffic from the user sockets is dropped. It turns out that we get a state mismatch in __xfrm_policy_check, because we end up trying to compare the encapsulation header's ports with the selector that's based on user traffic ports. Fixes: 0146dca70b87 ("xfrm: add support for UDPv6 encapsulation of ESP") Fixes: 26333c37fc28 ("xfrm: add IPv6 support for espintcp") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2020-07-27Merge tag 'sh-for-5.8-part2' of git://git.libc.org/linux-sh into masterLinus Torvalds
Pull arch/sh fixes from Rich Felker: "Two last-minute fixes: one is for a boot regression (mmu code broken) and the other fixes a long-standing broken syscall number bounds check" * tag 'sh-for-5.8-part2' of git://git.libc.org/linux-sh: sh: Fix validation of system call number sh/tlb: Fix PGTABLE_LEVELS > 2
2020-07-27fix a braino in cmsghdr_from_user_compat_to_kern()Al Viro
commit 547ce4cfb34c ("switch cmsghdr_from_user_compat_to_kern() to copy_from_user()") missed one of the places where ucmlen should've been replaced with cmsg.cmsg_len, now that we are fetching the entire struct rather than doing it field-by-field. As the result, compat sendmsg() with several different-sized cmsg attached started to fail with EINVAL. Trivial to fix, fortunately. Fixes: 547ce4cfb34c ("switch cmsghdr_from_user_compat_to_kern() to copy_from_user()") Reported-by: Nick Bowler <nbowler@draconx.ca> Tested-by: Nick Bowler <nbowler@draconx.ca> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 04:50:04 +0000