| Age | Commit message (Collapse) | Author |
|---|
|
The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.
The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.
However, often the counter tap is installed at the remote end of the gretap
tunnel. Since this is a SW-datapath scenario anyway, we can make the filter
arbitrarily accurate.
Thus in this patch, add parameters forward_type and backward_type to
several mirroring test helpers, as some other helpers already have. Then
change do_test_span_dir_ips() to instead of installing one generic tap and
using it for test in both directions, install the tap for each direction
separately, matching on the ICMP type given by these parameters.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test works by sending packets through a tunnel, whence they are
forwarded to a LAG. One of the LAG children is removed from the LAG prior
to the exercise, and the test then counts how many packets pass through the
other one. The issue with this is that it counts all packets, not just the
encapsulated ones.
So instead add a second gretap endpoint to receive the sent packets, and
check reception counters there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The argument $dir has a fallback value of "ingress". Move the fallback from
the usage site to the argument definition block to make the fact clearer.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The argument is not used by these functions except to propagate it for
ultimately no purpose.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some functions, argument-forwarding through "$@" without listing the
individual arguments explicitly is fundamental to the operation of a
function. E.g. xfail_on_veth() should be able to run various tests in the
fail-to-xfail regime, and usage of "$@" is appropriate as an abstraction
mechanism. For functions such as simple_if_init(), $@ is a handy way to
pass an array.
In other functions, it's merely a mechanism to save some typing, which
however ends up obscuring the real arguments and makes life hard for those
that end up reading the code.
This patch adds some of the implicit function arguments and correspondingly
expands $@'s. In several cases this will come in handy as following patches
adjust the parameter lists.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Danielle Ratson says:
====================
Add ability to flash modules' firmware
CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.2.2 of revision
4.0 of the CMIS standard.
According to the CMIS standard, the firmware update process is done
using a CDB commands sequence.
CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.12 of revision 4.0.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid RTNL
being held for too long and to allow several modules to be updated
simultaneously. The interface is designed with CMIS compliant modules in
mind, but kept generic enough to accommodate future use cases, if these
arise.
The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:
* The upper layer that will be triggered from the module layer, is
cmis_ fw_update.
* The lower one is cmis_cdb.
In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the cmis_cdb interface clean and
the cmis_fw_update specific to the cdb commands handling it.
The communication between the kernel and the driver will be done using
two ethtool operations that enable reading and writing the transceiver
module EEPROM.
The operation ethtool_ops::get_module_eeprom_by_page, that is already
implemented, will be used for reading from the EEPROM the CDB reply,
e.g. reading module setting, state, etc.
The operation ethtool_ops::set_module_eeprom_by_page, that is added in
the current patchset, will be used for writing to the EEPROM the CDB
command such as start firmware image, run firmware image, etc.
Therefore in order for a driver to implement module flashing, that
driver needs to implement the two functions mentioned above.
Patchset overview:
Patch #1-#2: Implement the EEPROM writing in mlxsw.
Patch #3: Define the interface between the kernel and user space.
Patch #4: Add ability to notify the flashing firmware progress.
Patch #5: Veto operations during flashing.
Patch #6: Add extended compliance codes.
Patch #7: Add the cdb layer.
Patch #8: Add the fw_update layer.
Patch #9: Add ability to flash transceiver modules' firmware.
v8:
Patch #7:
* In the ethtool_cmis_wait_for_cond() evaluate the condition once more
to decide if the error code should be -ETIMEDOUT or something else.
* s/netdev_err/netdev_err_once.
v7:
Patch #4:
* Return -ENOMEM instead of PTR_ERR(attr) on
ethnl_module_fw_flash_ntf_put_err().
Patch #9:
* Fix Warning for not unlocking the spin_lock in the error flow
on module_flash_fw_work_list_add().
* Avoid the fall-through on ethnl_sock_priv_destroy().
v6:
* Squash some of the last patch to patch #5 and patch #9.
Patch #3:
* Add paragraph in .rst file.
Patch #4:
* Reserve '1' more place on SKB for NUL terminator in
the error message string.
* Add more prints on error flow, re-write the printing
function and add ethnl_module_fw_flash_ntf_put_err().
* Change the communication method so notification will be
sent in unicast instead of multicast.
* Add new 'struct ethnl_module_fw_flash_ntf_params' that holds
the relevant info for unicast communication and use it to
send notification to the specific socket.
* s/nla_put_u64_64bit/nla_put_uint/
Patch #7:
* In ethtool_cmis_cdb_init(), Use 'const' for the 'params'
parameter.
Patch #8:
* Add a list field to struct ethtool_module_fw_flash for
module_fw_flash_work_list that will be presented in the next
patch.
* Move ethtool_cmis_fw_update() cleaning to a new function that
will be represented in the next patch.
* Move some of the fields in struct ethtool_module_fw_flash to
a separate struct, so ethtool_cmis_fw_update() will get only
the relevant parameters for it.
* Edit the relevant functions to get the relevant params for
them.
* s/CMIS_MODULE_READY_MAX_DURATION_USEC/CMIS_MODULE_READY_MAX_DURATION_MSEC
Patch #9:
* Add a paragraph in the commit message.
* Rename labels in module_flash_fw_schedule().
* Add info to genl_sk_priv_*() and implement the relevant
callbacks, in order to handle properly a scenario of closing
the socket from user space before the work item was ended.
* Add a list the holds all the ethtool_module_fw_flash struct
that corresponds to the in progress work items.
* Add a new enum for the socket types.
* Use both above to identify a flashing socket, add it to the
list and when closing socket affect only the flashing type.
* Create a new function that will get the work item instead of
ethtool_cmis_fw_update().
* Edit the relevant functions to get the relevant params for
them.
* The new function will call the old ethtool_cmis_fw_update(),
and do the cleaning, so the existence of the list should be
completely isolated in module.c.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ability to flash the modules' firmware by implementing the
interface between the user space and the kernel.
Example from a succeeding implementation:
# ethtool --flash-module-firmware swp40 file test.bin
Transceiver module firmware flashing started for device swp40
Transceiver module firmware flashing in progress for device swp40
Progress: 99%
Transceiver module firmware flashing completed for device swp40
In addition, add infrastructure that allows modules to set socket-specific
private data. This ensures that when a socket is closed from user space
during the flashing process, the right socket halts sending notifications
to user space until the work item is completed.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the CMIS standard, the firmware update process is done using
a CDB commands sequence.
Implement a work that will be triggered from the module layer in the
next patch the will initiate and execute all the CDB commands in order, to
eventually complete the firmware update process.
This flashing process includes, writing the firmware image, running the new
firmware image and committing it after testing, so that it will run upon
reset.
This work will also notify user space about the progress of the firmware
update process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.20 of revision 5.2.
Page 9Fh is used to specify the CDB command to be executed and also
provides an area for a local payload (LPL).
According to the CMIS standard, the firmware update process is done using
a CDB commands sequence that will be implemented in the next patch.
The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:
* The upper layer that will be triggered from the module layer, is
cmis_fw_update.
* The lower one is cmis_cdb.
In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the CDB interface clean and the
cmis_fw_update specific to the CDB commands handling it.
These two layers will communicate using the API the consists of three
functions:
- struct ethtool_cmis_cdb *
ethtool_cmis_cdb_init(struct net_device *dev,
struct ethtool_module_fw_flash_params *params);
- void ethtool_cmis_cdb_fini(struct ethtool_cmis_cdb *cdb);
- int ethtool_cmis_cdb_execute_cmd(struct net_device *dev,
struct ethtool_cmis_cdb_cmd_args *args);
Add the CDB layer to support initializing, finishing and executing CDB
commands:
* The initialization process will include creating of an ethtool_cmis_cdb
instance, querying the module CDB support, entering and validating the
password from user space (CMD 0x0000) and querying the module features
(CMD 0x0040).
* The finishing API will simply free the ethtool_cmis_cdb instance.
* The executing process will write the CDB command to EEPROM using
set_module_eeprom_by_page() that was presented earlier, and will
process the reply from EEPROM.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications.
Add SFF-8024 extended compliance code definitions for CMIS compliant
modules and use them in the next patch to determine the firmware flashing
work.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some operations cannot be performed during the firmware flashing
process.
For example:
- Port must be down during the whole flashing process to avoid packet loss
while committing reset for example.
- Writing to EEPROM interrupts the flashing process, so operations like
ethtool dump, module reset, get and set power mode should be vetoed.
- Split port firmware flashing should be vetoed.
In order to veto those scenarios, add a flag in 'struct net_device' that
indicates when a firmware flash is taking place on the module and use it
to prevent interruptions during the process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add progress notifications ability to user space while flashing modules'
firmware by implementing the interface between the user space and the
kernel.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.3.1 of revision 5.2 of
the CMIS standard.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid
RTNL being held for too long and to allow several modules to be
updated simultaneously. The interface is designed with CMIS compliant
modules in mind, but kept generic enough to accommodate future use
cases, if these arise.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the ethtool_ops::set_module_eeprom_by_page operation to allow
ethtool to write to a transceiver module EEPROM, in a similar fashion to
the ethtool_ops::get_module_eeprom_by_page operation.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethtool can already retrieve information from a transceiver module
EEPROM by invoking the ethtool_ops::get_module_eeprom_by_page operation.
Add a corresponding operation that allows ethtool to write to a
transceiver module EEPROM.
The new write operation is purely an in-kernel API and is not exposed to
user space.
The purpose of this operation is not to enable arbitrary read / write
access, but to allow the kernel to write to specific addresses as part
of transceiver module firmware flashing. In the future, more
functionality can be implemented on top of these read / write
operations.
Adjust the comments of the 'ethtool_module_eeprom' structure as it is
no longer used only for read access.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract known PHY IDs from Linux kernel realtek PHY driver
and convert them into supported compatible string list for
this DT binding document.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_devices from struct lmac by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev() to allocate the net_device object at
bgx_lmac_enable().
The free of the device occurs at bgx_lmac_disable().
Do not free_netdevice() if bgx_lmac_enable() fails after lmac->netdev
is allocated, since bgx_lmac_disable() is called if bgx_lmac_enable()
fails, and lmac->netdev will be freed there (similarly to lmac->dmacs).
Link: https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240626173503.87636-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 934c29999b57b835d65442da6f741d5e27f3b584.
This triggered a usercopy BUG() in systems with HIGHMEM, reported
by the test robot in:
https://lore.kernel.org/oe-lkp/202406161539.b5ff7b20-oliver.sang@intel.com
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://patch.msgid.link/20240626070153.759257-1-sagi@grimberg.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Aaron Conole says:
====================
selftests: net: Switch pmtu.sh to use the internal ovs script.
Currently, if a user wants to run pmtu.sh and cover all the provided test
cases, they need to install the Open vSwitch userspace utilities. This
dependency is difficult for users as well as CI environments, because the
userspace build and setup may require lots of support and devel packages
to be installed, system setup to be correct, and things like permissions
and selinux policies to be properly configured.
The kernel selftest suite includes an ovs-dpctl.py utility which can
interact with the openvswitch module directly. This lets developers and
CI environments run without needing too many extra dependencies - just
the pyroute2 python package.
This series enhances the ovs-dpctl utility to provide support for set()
and tunnel() flow specifiers, better ipv6 handling support, and the
ability to add tunnel vports, and LWT interfaces. Finally, it modifies
the pmtu.sh script to call the ovs-dpctl.py utility rather than the
typical OVS userspace utilities. The pmtu.sh can still fall back on
the Open vSwitch userspace utilities if the ovs-dpctl.py script can't
be used.
====================
Link: https://patch.msgid.link/20240625172245.233874-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pmtu testing will require that the OVS module is installed,
so do that.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-8-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current pmtu test infrastucture requires an installed copy of the
ovs-vswitchd userspace. This means that any automated or constrained
environments may not have the requisite tools to run the tests. However,
the pmtu tests don't require any special classifier processing. Indeed
they are only using the vswitchd in the most basic mode - as a NORMAL
switch.
However, the ovs-dpctl kernel utility can now program all the needed basic
flows to allow traffic to traverse the tunnels and provide support for at
least testing some basic pmtu scenarios. More complicated flow pipelines
can be added to the internal ovs test infrastructure, but that is work for
the future. For now, enable the most common cases - wide mega flows with
no other prerequisites.
Enhance the pmtu testing to try testing using the internal utility, first.
As a fallback, if the internal utility isn't running, then try with the
ovs-vswitchd userspace tools.
Additionally, make sure that when the pyroute2 package is not available
the ovs-dpctl utility will error out to properly signal an error has
occurred and skip using the internal utility.
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240625172245.233874-7-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current iteration of IPv6 support requires explicit fields to be set
in addition to not properly support the actual IPv6 addresses properly.
With this change, make it so that the ipv6() bare option is usable to
create wildcarded flows to match broad swaths of ipv6 traffic.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-6-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used when setting details about the tunnel to use as
transport. There is a difference between the ODP format between tunnel():
the 'key' flag is not actually a flag field, so we don't support it in the
same way that the vswitchd userspace supports displaying it.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240625172245.233874-5-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These will be used in upcoming commits to set specific attributes for
interacting with tunnels. Since set() will use the key parsing routine, we
also make sure to prepend it with an open paren, for the action parsing to
properly understand it.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-4-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Until recently, the ovs-dpctl utility was used with a limited actions set
and didn't need to have support for multiple similar actions. However,
when adding support for tunnels, it will be important to support multiple
set() actions in a single flow. When printing these actions, the existing
code will be unable to print all of the sets - it will only print the
first.
Refactor this code to be easier to read and support multiple actions of the
same type in an action list.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-3-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The OVS module can operate in conjunction with various types of
tunnel ports. These are created as either explicit tunnel vport
types, OR by creating a tunnel interface which acts as an anchor
for the lightweight tunnel support.
This patch adds the ability to add tunnel ports to an OVS
datapath for testing various scenarios with tunnel ports. With
this addition, the vswitch "plumbing" will at least be able to
push packets around using the tunnel vports. Future patches
will add support for setting required tunnel metadata for lwts
in the datapath. The end goal will be to push packets via these
tunnels, and will be used in an upcoming commit for testing the
path MTU.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-2-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With ARCH=s390, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/net/lcs.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20240625-md-s390-drivers-s390-net-v2-1-5a8a2b2f2ae3@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use display hints for formatting scalar attrs. This is specifically
useful for formatting IPv4 addresses carried typically as u32.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20240626201234.2572964-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Highlights this time are:
- cfg80211/nl80211:
* improvements for 6 GHz regulatory flexibility
- mac80211:
* use generic netdev stats
* multi-link improvements/fixes
- brcmfmac:
* MFP support (to enable WPA3)
- wilc1000:
* suspend/resume improvements
- iwlwifi:
* remove support for older FW for new devices
* fast resume (keeping the device configured)
- wl18xx:
* support newer firmware versions
* tag 'wireless-next-2024-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (100 commits)
wifi: brcmfmac: of: Support interrupts-extended
wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3
net: rfkill: Correct return value in invalid parameter case
wifi: mac80211: fix NULL dereference at band check in starting tx ba session
wifi: iwlwifi: mvm: fix rs.h kernel-doc
wifi: iwlwifi: fw: api: datapath: fix kernel-doc
wifi: iwlwifi: fix remaining mistagged kernel-doc comments
wifi: iwlwifi: fix prototype mismatch kernel-doc warnings
wifi: iwlwifi: fix kernel-doc in iwl-fh.h
wifi: iwlwifi: fix kernel-doc in iwl-trans.h
wifi: iwlwifi: pcie: fix kernel-doc
wifi: iwlwifi: dvm: fix kernel-doc warnings
wifi: iwlwifi: mvm: don't log error for failed UATS table read
wifi: iwlwifi: trans: make bad state warnings
wifi: iwlwifi: fw: api: fix some kernel-doc
wifi: iwlwifi: mvm: remove init_dbg module parameter
wifi: iwlwifi: update the BA notification API
wifi: iwlwifi: mvm: always unblock EMLSR on ROC end
wifi: iwlwifi: mvm: use IWL_FW_CHECK for link ID check
wifi: iwlwifi: mvm: don't flush BSSes on restart with MLD API
...
====================
Link: https://patch.msgid.link/20240627114135.28507-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a050 ("ionic: fix kernel panic due to multi-buffer handling")
d9c04209990b ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Just a few changes:
- maintainers: Larry Finger sadly passed away
- maintainers: ath trees are in their group now
- TXQ FQ quantum configuration fix
- TI wl driver: work around stuck FW in AP mode
- mac80211: disable softirqs in some new code
needing that
* tag 'wireless-2024-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
MAINTAINERS: wifi: update ath.git location
MAINTAINERS: Remembering Larry Finger
wifi: mac80211: disable softirqs for queued frame handling
wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values
wifi: wlcore: fix wlcore AP mode
====================
Link: https://patch.msgid.link/20240627083627.15312-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can, bpf and netfilter.
There are a bunch of regressions addressed here, but hopefully nothing
spectacular. We are still waiting the driver fix from Intel, mentioned
by Jakub in the previous networking pull.
Current release - regressions:
- core: add softirq safety to netdev_rename_lock
- tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed
TFO
- batman-adv: fix RCU race at module unload time
Previous releases - regressions:
- openvswitch: get related ct labels from its master if it is not
confirmed
- eth: bonding: fix incorrect software timestamping report
- eth: mlxsw: fix memory corruptions on spectrum-4 systems
- eth: ionic: use dev_consume_skb_any outside of napi
Previous releases - always broken:
- netfilter: fully validate NFT_DATA_VALUE on store to data registers
- unix: several fixes for OoB data
- tcp: fix race for duplicate reqsk on identical SYN
- bpf:
- fix may_goto with negative offset
- fix the corner case with may_goto and jump to the 1st insn
- fix overrunning reservations in ringbuf
- can:
- j1939: recover socket queue on CAN bus error during BAM
transmission
- mcp251xfd: fix infinite loop when xmit fails
- dsa: microchip: monitor potential faults in half-duplex mode
- eth: vxlan: pull inner IP header in vxlan_xmit_one()
- eth: ionic: fix kernel panic due to multi-buffer handling
Misc:
- selftest: unix tests refactor and a lot of new cases added"
* tag 'net-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
net: mana: Fix possible double free in error handling path
selftest: af_unix: Check SIOCATMARK after every send()/recv() in msg_oob.c.
af_unix: Fix wrong ioctl(SIOCATMARK) when consumed OOB skb is at the head.
selftest: af_unix: Check EPOLLPRI after every send()/recv() in msg_oob.c
selftest: af_unix: Check SIGURG after every send() in msg_oob.c
selftest: af_unix: Add SO_OOBINLINE test cases in msg_oob.c
af_unix: Don't stop recv() at consumed ex-OOB skb.
selftest: af_unix: Add non-TCP-compliant test cases in msg_oob.c.
af_unix: Don't stop recv(MSG_DONTWAIT) if consumed OOB skb is at the head.
af_unix: Stop recv(MSG_PEEK) at consumed OOB skb.
selftest: af_unix: Add msg_oob.c.
selftest: af_unix: Remove test_unix_oob.c.
tracing/net_sched: NULL pointer dereference in perf_trace_qdisc_reset()
netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers
net: usb: qmi_wwan: add Telit FN912 compositions
tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed TFO
ionic: use dev_consume_skb_any outside of napi
net: dsa: microchip: fix wrong register write when masking interrupt
Fix race for duplicate reqsk on identical SYN
ibmvnic: Add tx check to prevent skb leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became bigger than usual, as it receives a pile of pending ASoC
fixes. Most of changes are for device-specific issues while there are
a few core fixes that are all rather trivial:
- DMA-engine sync fixes
- Continued MIDI2 conversion fixes
- Various ASoC Intel SOF fixes
- A series of ASoC topology fixes for memory handling
- AMD ACP fix, curing a recent regression, too
- Platform / codec-specific fixes for mediatek, atmel, realtek, etc"
* tag 'sound-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (40 commits)
ASoC: rt5645: fix issue of random interrupt from push-button
ALSA: seq: Fix missing MSB in MIDI2 SPP conversion
ASoC: amd: yc: Fix non-functional mic on ASUS M5602RA
ALSA: hda/realtek: fix mute/micmute LEDs don't work for EliteBook 645/665 G11.
ALSA: hda/realtek: Fix conflicting quirk for PCI SSID 17aa:3820
ALSA: dmaengine_pcm: terminate dmaengine before synchronize
ALSA: hda/relatek: Enable Mute LED on HP Laptop 15-gw0xxx
ALSA: PCM: Allow resume only for suspended streams
ALSA: seq: Fix missing channel at encoding RPN/NRPN MIDI2 messages
ASoC: mediatek: mt8195: Add platform entry for ETDM1_OUT_BE dai link
ASoC: fsl-asoc-card: set priv->pdev before using it
ASoC: amd: acp: move chip->flag variable assignment
ASoC: amd: acp: remove i2s configuration check in acp_i2s_probe()
ASoC: amd: acp: add a null check for chip_pdev structure
ASoC: Intel: soc-acpi: mtl: fix speaker no sound on Dell SKU 0C64
ASoC: q6apm-lpass-dai: close graph on prepare errors
ASoC: cs35l56: Disconnect ASP1 TX sources when ASP1 DAI is hooked up
ASoC: topology: Fix route memory corruption
ASoC: rt722-sdca-sdw: add debounce time for type detection
ASoC: SOF: sof-audio: Skip unprepare for in-use widgets on error rollback
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two Netfilter fixes for net:
Patch #1 fixes CONFIG_SYSCTL=n for a patch coming in the previous PR
to move the sysctl toggle to enable SRv6 netfilter hooks from
nf_conntrack to the core, from Jianguo Wu.
Patch #2 fixes a possible pointer leak to userspace due to insufficient
validation of NFT_DATA_VALUE.
Linus found this pointer leak to userspace via zdi-disclosures@ and
forwarded the notice to Netfilter maintainers, he appears as reporter
because whoever found this issue never approached Netfilter
maintainers neither via security@ nor in private.
netfilter pull request 24-06-27
* tag 'nf-24-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers
netfilter: fix undefined reference to 'netfilter_lwtunnel_*' when CONFIG_SYSCTL=n
====================
Link: https://patch.msgid.link/20240626233845.151197-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function adev_release
calls kfree(madev). We shouldn't call kfree(madev) again
in the error handling path. Set 'madev' to NULL.
Fixes: a69839d4327d ("net: mana: Add support for auxiliary device")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20240625130314.2661257-1-make24@iscas.ac.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Kuniyuki Iwashima says:
====================
af_unix: Fix bunch of MSG_OOB bugs and add new tests.
This series rewrites the selftest for AF_UNIX MSG_OOB and fixes
bunch of bugs that AF_UNIX behaves differently compared to TCP.
Note that the test discovered few more bugs in TCP side, which
will be fixed in another series.
====================
Link: https://lore.kernel.org/r/20240625013645.45034-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
To catch regression, let's check ioctl(SIOCATMARK) after every
send() and recv() calls.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Even if OOB data is recv()ed, ioctl(SIOCATMARK) must return 1 when the
OOB skb is at the head of the receive queue and no new OOB data is queued.
Without fix:
# RUN msg_oob.no_peek.oob ...
# msg_oob.c:305:oob:Expected answ[0] (0) == oob_head (1)
# oob: Test terminated by assertion
# FAIL msg_oob.no_peek.oob
not ok 2 msg_oob.no_peek.oob
With fix:
# RUN msg_oob.no_peek.oob ...
# OK msg_oob.no_peek.oob
ok 2 msg_oob.no_peek.oob
Fixes: 314001f0bf92 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When OOB data is in recvq, we can detect it with epoll by checking
EPOLLPRI.
This patch add checks for EPOLLPRI after every send() and recv() in
all test cases.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When data is sent with MSG_OOB, SIGURG is sent to a process if the
receiver socket has set its owner to the process by ioctl(FIOSETOWN)
or fcntl(F_SETOWN).
This patch adds SIGURG check after every send(MSG_OOB) call.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When SO_OOBINLINE is enabled on a socket, MSG_OOB can be recv()ed
without MSG_OOB flag, and ioctl(SIOCATMARK) will behaves differently.
This patch adds some test cases for SO_OOBINLINE.
Note the new test cases found two bugs in TCP.
1) After reading OOB data with non-inline mode, we can re-read
the data by setting SO_OOBINLINE.
# RUN msg_oob.no_peek.inline_oob_ahead_break ...
# msg_oob.c:146:inline_oob_ahead_break:AF_UNIX :world
# msg_oob.c:147:inline_oob_ahead_break:TCP :oworld
# OK msg_oob.no_peek.inline_oob_ahead_break
ok 14 msg_oob.no_peek.inline_oob_ahead_break
2) The head OOB data is dropped if SO_OOBINLINE is disabled
if a new OOB data is queued.
# RUN msg_oob.no_peek.inline_ex_oob_drop ...
# msg_oob.c:171:inline_ex_oob_drop:AF_UNIX :x
# msg_oob.c:172:inline_ex_oob_drop:TCP :y
# msg_oob.c:146:inline_ex_oob_drop:AF_UNIX :y
# msg_oob.c:147:inline_ex_oob_drop:TCP :Resource temporarily unavailable
# OK msg_oob.no_peek.inline_ex_oob_drop
ok 17 msg_oob.no_peek.inline_ex_oob_drop
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, recv() is stopped at a consumed OOB skb even if a new
OOB skb is queued and we can ignore the old OOB skb.
>>> from socket import *
>>> c1, c2 = socket(AF_UNIX, SOCK_STREAM)
>>> c1.send(b'hellowor', MSG_OOB)
8
>>> c2.recv(1, MSG_OOB) # consume OOB data stays at middle of recvq.
b'r'
>>> c1.send(b'ld', MSG_OOB)
2
>>> c2.recv(10) # recv() stops at the old consumed OOB
b'hellowo' # should be 'hellowol'
manage_oob() should not stop recv() at the old consumed OOB skb if
there is a new OOB data queued.
Note that TCP behaviour is apparently wrong in this test case because
we can recv() the same OOB data twice.
Without fix:
# RUN msg_oob.no_peek.ex_oob_ahead_break ...
# msg_oob.c:138:ex_oob_ahead_break:AF_UNIX :hellowo
# msg_oob.c:139:ex_oob_ahead_break:Expected:hellowol
# msg_oob.c:141:ex_oob_ahead_break:Expected ret[0] (7) == expected_len (8)
# ex_oob_ahead_break: Test terminated by assertion
# FAIL msg_oob.no_peek.ex_oob_ahead_break
not ok 11 msg_oob.no_peek.ex_oob_ahead_break
With fix:
# RUN msg_oob.no_peek.ex_oob_ahead_break ...
# msg_oob.c:146:ex_oob_ahead_break:AF_UNIX :hellowol
# msg_oob.c:147:ex_oob_ahead_break:TCP :helloworl
# OK msg_oob.no_peek.ex_oob_ahead_break
ok 11 msg_oob.no_peek.ex_oob_ahead_break
Fixes: 314001f0bf92 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While testing, I found some weird behaviour on the TCP side as well.
For example, TCP drops the preceding OOB data when queueing a new
OOB data if the old OOB data is at the head of recvq.
# RUN msg_oob.no_peek.ex_oob_drop ...
# msg_oob.c:146:ex_oob_drop:AF_UNIX :x
# msg_oob.c:147:ex_oob_drop:TCP :Resource temporarily unavailable
# msg_oob.c:146:ex_oob_drop:AF_UNIX :y
# msg_oob.c:147:ex_oob_drop:TCP :Invalid argument
# OK msg_oob.no_peek.ex_oob_drop
ok 9 msg_oob.no_peek.ex_oob_drop
# RUN msg_oob.no_peek.ex_oob_drop_2 ...
# msg_oob.c:146:ex_oob_drop_2:AF_UNIX :x
# msg_oob.c:147:ex_oob_drop_2:TCP :Resource temporarily unavailable
# OK msg_oob.no_peek.ex_oob_drop_2
ok 10 msg_oob.no_peek.ex_oob_drop_2
This patch allows AF_UNIX's MSG_OOB implementation to produce different
results from TCP when operations are guarded with tcp_incompliant{}.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Let's say a socket send()s "hello" with MSG_OOB and "world" without flags,
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX)
>>> c1.send(b'hello', MSG_OOB)
5
>>> c1.send(b'world')
5
and its peer recv()s "hell" and "o".
>>> c2.recv(10)
b'hell'
>>> c2.recv(1, MSG_OOB)
b'o'
Now the consumed OOB skb stays at the head of recvq to return a correct
value for ioctl(SIOCATMARK), which is broken now and fixed by a later
patch.
Then, if peer issues recv() with MSG_DONTWAIT, manage_oob() returns NULL,
so recv() ends up with -EAGAIN.
>>> c2.setblocking(False) # This causes -EAGAIN even with available data
>>> c2.recv(5)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
BlockingIOError: [Errno 11] Resource temporarily unavailable
However, next recv() will return the following available data, "world".
>>> c2.recv(5)
b'world'
When the consumed OOB skb is at the head of the queue, we need to fetch
the next skb to fix the weird behaviour.
Note that the issue does not happen without MSG_DONTWAIT because we can
retry after manage_oob().
This patch also adds a test case that covers the issue.
Without fix:
# RUN msg_oob.no_peek.ex_oob_break ...
# msg_oob.c:134:ex_oob_break:AF_UNIX :Resource temporarily unavailable
# msg_oob.c:135:ex_oob_break:Expected:ld
# msg_oob.c:137:ex_oob_break:Expected ret[0] (-1) == expected_len (2)
# ex_oob_break: Test terminated by assertion
# FAIL msg_oob.no_peek.ex_oob_break
not ok 8 msg_oob.no_peek.ex_oob_break
With fix:
# RUN msg_oob.no_peek.ex_oob_break ...
# OK msg_oob.no_peek.ex_oob_break
ok 8 msg_oob.no_peek.ex_oob_break
Fixes: 314001f0bf92 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After consuming OOB data, recv() reading the preceding data must break at
the OOB skb regardless of MSG_PEEK.
Currently, MSG_PEEK does not stop recv() for AF_UNIX, and the behaviour is
not compliant with TCP.
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX)
>>> c1.send(b'hello', MSG_OOB)
5
>>> c1.send(b'world')
5
>>> c2.recv(1, MSG_OOB)
b'o'
>>> c2.recv(9, MSG_PEEK) # This should return b'hell'
b'hellworld' # even with enough buffer.
Let's fix it by returning NULL for consumed skb and unlinking it only if
MSG_PEEK is not specified.
This patch also adds test cases that add recv(MSG_PEEK) before each recv().
Without fix:
# RUN msg_oob.peek.oob_ahead_break ...
# msg_oob.c:134:oob_ahead_break:AF_UNIX :hellworld
# msg_oob.c:135:oob_ahead_break:Expected:hell
# msg_oob.c:137:oob_ahead_break:Expected ret[0] (9) == expected_len (4)
# oob_ahead_break: Test terminated by assertion
# FAIL msg_oob.peek.oob_ahead_break
not ok 13 msg_oob.peek.oob_ahead_break
With fix:
# RUN msg_oob.peek.oob_ahead_break ...
# OK msg_oob.peek.oob_ahead_break
ok 13 msg_oob.peek.oob_ahead_break
Fixes: 314001f0bf92 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
AF_UNIX's MSG_OOB functionality lacked thorough testing, and we found
some bizarre behaviour.
The new selftest validates every MSG_OOB operation against TCP as a
reference implementation.
This patch adds only a few tests with basic send() and recv() that
do not fail.
The following patches will add more test cases for SO_OOBINLINE, SIGURG,
EPOLLPRI, and SIOCATMARK.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
test_unix_oob.c does not fully cover AF_UNIX's MSG_OOB functionality,
thus there are discrepancies between TCP behaviour.
Also, the test uses fork() to create message producer, and it's not
easy to understand and add more test cases.
Let's remove test_unix_oob.c and rewrite a new test.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the TRACE_EVENT(qdisc_reset) NULL dereference occurred from
qdisc->dev_queue->dev <NULL> ->name
This situation simulated from bunch of veths and Bluetooth disconnection
and reconnection.
During qdisc initialization, qdisc was being set to noop_queue.
In veth_init_queue, the initial tx_num was reduced back to one,
causing the qdisc reset to be called with noop, which led to the kernel
panic.
I've attached the GitHub gist link that C converted syz-execprogram
source code and 3 log of reproduced vmcore-dmesg.
https://gist.github.com/yskelg/cc64562873ce249cdd0d5a358b77d740
Yeoreum and I use two fuzzing tool simultaneously.
One process with syz-executor : https://github.com/google/syzkaller
$ ./syz-execprog -executor=./syz-executor -repeat=1 -sandbox=setuid \
-enable=none -collide=false log1
The other process with perf fuzzer:
https://github.com/deater/perf_event_tests/tree/master/fuzzer
$ perf_event_tests/fuzzer/perf_fuzzer
I think this will happen on the kernel version.
Linux kernel version +v6.7.10, +v6.8, +v6.9 and it could happen in v6.10.
This occurred from 51270d573a8d. I think this patch is absolutely
necessary. Previously, It was showing not intended string value of name.
I've reproduced 3 time from my fedora 40 Debug Kernel with any other module
or patched.
version: 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug
[ 5287.164555] veth0_vlan: left promiscuous mode
[ 5287.164929] veth1_macvtap: left promiscuous mode
[ 5287.164950] veth0_macvtap: left promiscuous mode
[ 5287.164983] veth1_vlan: left promiscuous mode
[ 5287.165008] veth0_vlan: left promiscuous mode
[ 5287.165450] veth1_macvtap: left promiscuous mode
[ 5287.165472] veth0_macvtap: left promiscuous mode
[ 5287.165502] veth1_vlan: left promiscuous mode
…
[ 5297.598240] bridge0: port 2(bridge_slave_1) entered blocking state
[ 5297.598262] bridge0: port 2(bridge_slave_1) entered forwarding state
[ 5297.598296] bridge0: port 1(bridge_slave_0) entered blocking state
[ 5297.598313] bridge0: port 1(bridge_slave_0) entered forwarding state
[ 5297.616090] 8021q: adding VLAN 0 to HW filter on device bond0
[ 5297.620405] bridge0: port 1(bridge_slave_0) entered disabled state
[ 5297.620730] bridge0: port 2(bridge_slave_1) entered disabled state
[ 5297.627247] 8021q: adding VLAN 0 to HW filter on device team0
[ 5297.629636] bridge0: port 1(bridge_slave_0) entered blocking state
…
[ 5298.002798] bridge_slave_0: left promiscuous mode
[ 5298.002869] bridge0: port 1(bridge_slave_0) entered disabled state
[ 5298.309444] bond0 (unregistering): (slave bond_slave_0): Releasing backup interface
[ 5298.315206] bond0 (unregistering): (slave bond_slave_1): Releasing backup interface
[ 5298.320207] bond0 (unregistering): Released all slaves
[ 5298.354296] hsr_slave_0: left promiscuous mode
[ 5298.360750] hsr_slave_1: left promiscuous mode
[ 5298.374889] veth1_macvtap: left promiscuous mode
[ 5298.374931] veth0_macvtap: left promiscuous mode
[ 5298.374988] veth1_vlan: left promiscuous mode
[ 5298.375024] veth0_vlan: left promiscuous mode
[ 5299.109741] team0 (unregistering): Port device team_slave_1 removed
[ 5299.185870] team0 (unregistering): Port device team_slave_0 removed
…
[ 5300.155443] Bluetooth: hci3: unexpected cc 0x0c03 length: 249 > 1
[ 5300.155724] Bluetooth: hci3: unexpected cc 0x1003 length: 249 > 9
[ 5300.155988] Bluetooth: hci3: unexpected cc 0x1001 length: 249 > 9
….
[ 5301.075531] team0: Port device team_slave_1 added
[ 5301.085515] bridge0: port 1(bridge_slave_0) entered blocking state
[ 5301.085531] bridge0: port 1(bridge_slave_0) entered disabled state
[ 5301.085588] bridge_slave_0: entered allmulticast mode
[ 5301.085800] bridge_slave_0: entered promiscuous mode
[ 5301.095617] bridge0: port 1(bridge_slave_0) entered blocking state
[ 5301.095633] bridge0: port 1(bridge_slave_0) entered disabled state
…
[ 5301.149734] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 5301.173234] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 5301.180517] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 5301.193481] hsr_slave_0: entered promiscuous mode
[ 5301.204425] hsr_slave_1: entered promiscuous mode
[ 5301.210172] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 5301.210185] Cannot create hsr debugfs directory
[ 5301.224061] bond0: (slave bond_slave_1): Enslaving as an active interface with an up link
[ 5301.246901] bond0: (slave bond_slave_0): Enslaving as an active interface with an up link
[ 5301.255934] team0: Port device team_slave_0 added
[ 5301.256480] team0: Port device team_slave_1 added
[ 5301.256948] team0: Port device team_slave_0 added
…
[ 5301.435928] hsr_slave_0: entered promiscuous mode
[ 5301.446029] hsr_slave_1: entered promiscuous mode
[ 5301.455872] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 5301.455884] Cannot create hsr debugfs directory
[ 5301.502664] hsr_slave_0: entered promiscuous mode
[ 5301.513675] hsr_slave_1: entered promiscuous mode
[ 5301.526155] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 5301.526164] Cannot create hsr debugfs directory
[ 5301.563662] hsr_slave_0: entered promiscuous mode
[ 5301.576129] hsr_slave_1: entered promiscuous mode
[ 5301.580259] debugfs: Directory 'hsr0' with parent 'hsr' already present!
[ 5301.580270] Cannot create hsr debugfs directory
[ 5301.590269] 8021q: adding VLAN 0 to HW filter on device bond0
[ 5301.595872] KASAN: null-ptr-deref in range [0x0000000000000130-0x0000000000000137]
[ 5301.595877] Mem abort info:
[ 5301.595881] ESR = 0x0000000096000006
[ 5301.595885] EC = 0x25: DABT (current EL), IL = 32 bits
[ 5301.595889] SET = 0, FnV = 0
[ 5301.595893] EA = 0, S1PTW = 0
[ 5301.595896] FSC = 0x06: level 2 translation fault
[ 5301.595900] Data abort info:
[ 5301.595903] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000
[ 5301.595907] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 5301.595911] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 5301.595915] [dfff800000000026] address between user and kernel address ranges
[ 5301.595971] Internal error: Oops: 0000000096000006 [#1] SMP
…
[ 5301.596076] CPU: 2 PID: 102769 Comm:
syz-executor.3 Kdump: loaded Tainted:
G W ------- --- 6.10.0-0.rc2.20240608gitdc772f8237f9.29.fc41.aarch64+debug #1
[ 5301.596080] Hardware name: VMware, Inc. VMware20,1/VBSA,
BIOS VMW201.00V.21805430.BA64.2305221830 05/22/2023
[ 5301.596082] pstate: 01400005 (nzcv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 5301.596085] pc : strnlen+0x40/0x88
[ 5301.596114] lr : trace_event_get_offsets_qdisc_reset+0x6c/0x2b0
[ 5301.596124] sp : ffff8000beef6b40
[ 5301.596126] x29: ffff8000beef6b40 x28: dfff800000000000 x27: 0000000000000001
[ 5301.596131] x26: 6de1800082c62bd0 x25: 1ffff000110aa9e0 x24: ffff800088554f00
[ 5301.596136] x23: ffff800088554ec0 x22: 0000000000000130 x21: 0000000000000140
[ 5301.596140] x20: dfff800000000000 x19: ffff8000beef6c60 x18: ffff7000115106d8
[ 5301.596143] x17: ffff800121bad000 x16: ffff800080020000 x15: 0000000000000006
[ 5301.596147] x14: 0000000000000002 x13: ffff0001f3ed8d14 x12: ffff700017ddeda5
[ 5301.596151] x11: 1ffff00017ddeda4 x10: ffff700017ddeda4 x9 : ffff800082cc5eec
[ 5301.596155] x8 : 0000000000000004 x7 : 00000000f1f1f1f1 x6 : 00000000f2f2f200
[ 5301.596158] x5 : 00000000f3f3f3f3 x4 : ffff700017dded80 x3 : 00000000f204f1f1
[ 5301.596162] x2 : 0000000000000026 x1 : 0000000000000000 x0 : 0000000000000130
[ 5301.596166] Call trace:
[ 5301.596175] strnlen+0x40/0x88
[ 5301.596179] trace_event_get_offsets_qdisc_reset+0x6c/0x2b0
[ 5301.596182] perf_trace_qdisc_reset+0xb0/0x538
[ 5301.596184] __traceiter_qdisc_reset+0x68/0xc0
[ 5301.596188] qdisc_reset+0x43c/0x5e8
[ 5301.596190] netif_set_real_num_tx_queues+0x288/0x770
[ 5301.596194] veth_init_queues+0xfc/0x130 [veth]
[ 5301.596198] veth_newlink+0x45c/0x850 [veth]
[ 5301.596202] rtnl_newlink_create+0x2c8/0x798
[ 5301.596205] __rtnl_newlink+0x92c/0xb60
[ 5301.596208] rtnl_newlink+0xd8/0x130
[ 5301.596211] rtnetlink_rcv_msg+0x2e0/0x890
[ 5301.596214] netlink_rcv_skb+0x1c4/0x380
[ 5301.596225] rtnetlink_rcv+0x20/0x38
[ 5301.596227] netlink_unicast+0x3c8/0x640
[ 5301.596231] netlink_sendmsg+0x658/0xa60
[ 5301.596234] __sock_sendmsg+0xd0/0x180
[ 5301.596243] __sys_sendto+0x1c0/0x280
[ 5301.596246] __arm64_sys_sendto+0xc8/0x150
[ 5301.596249] invoke_syscall+0xdc/0x268
[ 5301.596256] el0_svc_common.constprop.0+0x16c/0x240
[ 5301.596259] do_el0_svc+0x48/0x68
[ 5301.596261] el0_svc+0x50/0x188
[ 5301.596265] el0t_64_sync_handler+0x120/0x130
[ 5301.596268] el0t_64_sync+0x194/0x198
[ 5301.596272] Code: eb15001f 54000120 d343fc02 12000801 (38f46842)
[ 5301.596285] SMP: stopping secondary CPUs
[ 5301.597053] Starting crashdump kernel...
[ 5301.597057] Bye!
After applying our patch, I didn't find any kernel panic errors.
We've found a simple reproducer
# echo 1 > /sys/kernel/debug/tracing/events/qdisc/qdisc_reset/enable
# ip link add veth0 type veth peer name veth1
Error: Unknown device type.
However, without our patch applied, I tested upstream 6.10.0-rc3 kernel
using the qdisc_reset event and the ip command on my qemu virtual machine.
This 2 commands makes always kernel panic.
Linux version: 6.10.0-rc3
[ 0.000000] Linux version 6.10.0-rc3-00164-g44ef20baed8e-dirty
(paran@fedora) (gcc (GCC) 14.1.1 20240522 (Red Hat 14.1.1-4), GNU ld
version 2.41-34.fc40) #20 SMP PREEMPT Sat Jun 15 16:51:25 KST 2024
Kernel panic message:
[ 615.236484] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
[ 615.237250] Dumping ftrace buffer:
[ 615.237679] (ftrace buffer empty)
[ 615.238097] Modules linked in: veth crct10dif_ce virtio_gpu
virtio_dma_buf drm_shmem_helper drm_kms_helper zynqmp_fpga xilinx_can
xilinx_spi xilinx_selectmap xilinx_core xilinx_pr_decoupler versal_fpga
uvcvideo uvc videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videodev
videobuf2_common mc usbnet deflate zstd ubifs ubi rcar_canfd rcar_can
omap_mailbox ntb_msi_test ntb_hw_epf lattice_sysconfig_spi
lattice_sysconfig ice40_spi gpio_xilinx dwmac_altr_socfpga mdio_regmap
stmmac_platform stmmac pcs_xpcs dfl_fme_region dfl_fme_mgr dfl_fme_br
dfl_afu dfl fpga_region fpga_bridge can can_dev br_netfilter bridge stp
llc atl1c ath11k_pci mhi ath11k_ahb ath11k qmi_helpers ath10k_sdio
ath10k_pci ath10k_core ath mac80211 libarc4 cfg80211 drm fuse backlight ipv6
Jun 22 02:36:5[3 6k152.62-4sm98k4-0k]v kCePUr:n e1l :P IUDn:a b4le6
8t oC ohmma: nidpl eN oketr nteali nptaedg i6n.g1 0re.0q-urecs3t- 0at0
1v6i4r-tgu4a4le fa2d0dbraeeds0se-dir tyd f#f2f08
615.252376] Hardware name: linux,dummy-virt (DT)
[ 615.253220] pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS
BTYPE=--)
[ 615.254433] pc : strnlen+0x6c/0xe0
[ 615.255096] lr : trace_event_get_offsets_qdisc_reset+0x94/0x3d0
[ 615.256088] sp : ffff800080b269a0
[ 615.256615] x29: ffff800080b269a0 x28: ffffc070f3f98500 x27:
0000000000000001
[ 615.257831] x26: 0000000000000010 x25: ffffc070f3f98540 x24:
ffffc070f619cf60
[ 615.259020] x23: 0000000000000128 x22: 0000000000000138 x21:
dfff800000000000
[ 615.260241] x20: ffffc070f631ad00 x19: 0000000000000128 x18:
ffffc070f448b800
[ 615.261454] x17: 0000000000000000 x16: 0000000000000001 x15:
ffffc070f4ba2a90
[ 615.262635] x14: ffff700010164d73 x13: 1ffff80e1e8d5eb3 x12:
1ffff00010164d72
[ 615.263877] x11: ffff700010164d72 x10: dfff800000000000 x9 :
ffffc070e85d6184
[ 615.265047] x8 : ffffc070e4402070 x7 : 000000000000f1f1 x6 :
000000001504a6d3
[ 615.266336] x5 : ffff28ca21122140 x4 : ffffc070f5043ea8 x3 :
0000000000000000
[ 615.267528] x2 : 0000000000000025 x1 : 0000000000000000 x0 :
0000000000000000
[ 615.268747] Call trace:
[ 615.269180] strnlen+0x6c/0xe0
[ 615.269767] trace_event_get_offsets_qdisc_reset+0x94/0x3d0
[ 615.270716] trace_event_raw_event_qdisc_reset+0xe8/0x4e8
[ 615.271667] __traceiter_qdisc_reset+0xa0/0x140
[ 615.272499] qdisc_reset+0x554/0x848
[ 615.273134] netif_set_real_num_tx_queues+0x360/0x9a8
[ 615.274050] veth_init_queues+0x110/0x220 [veth]
[ 615.275110] veth_newlink+0x538/0xa50 [veth]
[ 615.276172] __rtnl_newlink+0x11e4/0x1bc8
[ 615.276944] rtnl_newlink+0xac/0x120
[ 615.277657] rtnetlink_rcv_msg+0x4e4/0x1370
[ 615.278409] netlink_rcv_skb+0x25c/0x4f0
[ 615.279122] rtnetlink_rcv+0x48/0x70
[ 615.279769] netlink_unicast+0x5a8/0x7b8
[ 615.280462] netlink_sendmsg+0xa70/0x1190
Yeoreum and I don't know if the patch we wrote will fix the underlying
cause, but we think that priority is to prevent kernel panic happening.
So, we're sending this patch.
Fixes: 51270d573a8d ("tracing/net_sched: Fix tracepoints that save qdisc_dev() as a string")
Link: https://lore.kernel.org/lkml/20240229143432.273b4871@gandalf.local.home/t/
Cc: netdev@vger.kernel.org
Tested-by: Yunseong Kim <yskelg@gmail.com>
Signed-off-by: Yunseong Kim <yskelg@gmail.com>
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Link: https://lore.kernel.org/r/20240624173320.24945-4-yskelg@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Christophe Roullier says:
====================
Series to deliver Ethernet for STM32MP25
STM32MP25 is STM32 SOC with 2 GMACs instances.
GMAC IP version is SNPS 5.3x.
GMAC IP configure with 2 RX and 4 TX queue.
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
TSO supported
====================
Link: https://lore.kernel.org/r/20240624071052.118042-1-christophe.roullier@foss.st.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add Ethernet support for STM32MP25.
STM32MP25 is STM32 SOC with 2 GMACs instances.
GMAC IP version is SNPS 5.3x.
GMAC IP configure with 2 RX and 4 TX queue.
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
TSO supported
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
